summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/ipr.c
Commit message (Collapse)AuthorAgeFilesLines
* [SCSI] ipr: fix possible false positive detection of stuck interruptWayne Boyer2011-05-241-6/+6
| | | | | | | | | | | | | | | | If the driver is getting flooded with interrupts, there's a possibility that the interrupt service routine could falsely detect a stuck interrupt condition and reset the adapter. This patch changes the logic such that the routine will loop back into the command processing code one more time after detecting the stuck interrupt signature. If there are no commands to process after that pass, and the interrupt is still not cleared, then the driver will print the "Error clearing HRRQ" message and reset the adapter. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <jbottomley@parallels.com>
* [SCSI] ipr: Rate limit DMA mapping errorsAnton Blanchard2011-05-171-1/+2
| | | | | | | | | | | I noticed a stream of errors from the IPR driver while doing IOMMU fault injection. Rate limit the errors so we don't clog up the console and logfiles. Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <jbottomley@parallels.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: increase the dump size for 64 bit adaptersKleber Sacilotto de Souza2011-05-011-15/+65
| | | | | | | | | | | | | | | Currently the size of the dump generated by the driver is limited in 4MB, which is insufficient to gather much useful data from the new 64 bit adapters. This patch makes the needed changes to increase the dump limit for the 64 bit adapters to 32MB, or even to a bigger value in the future, but keeping the current limitations for the legacy 32 bit adapters. Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: improve interrupt service routine performanceWayne Boyer2011-05-011-29/+39
| | | | | | | | | | | | | | | | | | | | | During performance testing on P7 machines it was observed that the interrupt service routine was doing unnecessary MMIO operations. This patch rearranges the logic of the routine and moves some of the code out of the main routine. The result is that there are now fewer MMIO operations in the performance path of the code. As a result of the above change, an existing condition was exposed where the driver could get an "unexpected" hrrq interrupt. The original code would flag the interrupt as unexpected and then reset the adapter. After further analysis it was confirmed that this condition can occasionally occur and that the interrupt can safely be ignored. Additional code in this patch detects this condition, clears the interrupt and allows the driver to continue without resetting the adapter. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: remove unneeded volatile declarationsWayne Boyer2011-05-011-3/+3
| | | | | | | | | This patch removes three volatile declarations based on some feedback and code analysis. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix synchronous request flags for better performanceWayne Boyer2011-05-011-1/+2
| | | | | | | | | | In testing it was noticed that Extended Delay after Reset flag was being set for gscsi and volume set devices. This had a negative effect on performance for volume sets. The fix is to only set the flag for gscsi devices. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds2011-03-171-3/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits) [SCSI] scsi_dh_rdac: Add MD36xxf into device list [SCSI] scsi_debug: add consecutive medium errors [SCSI] libsas: fix ata list corruption issue [SCSI] hpsa: export resettable host attribute [SCSI] hpsa: move device attributes to avoid forward declarations [SCSI] scsi_debug: Logical Block Provisioning (SBC3r26) [SCSI] sd: Logical Block Provisioning update [SCSI] Include protection operation in SCSI command trace [SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try) [SCSI] target: Fix volume size misreporting for volumes > 2TB [SCSI] bnx2fc: Broadcom FCoE offload driver [SCSI] fcoe: fix broken fcoe interface reset [SCSI] fcoe: precedence bug in fcoe_filter_frames() [SCSI] libfcoe: Remove stale fcoe-netdev entries [SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h [SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument [SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs [SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out" [SCSI] libfc: Fixing a memory leak when destroying an interface [SCSI] megaraid_sas: Version and Changelog update ... Fix up trivial conflicts due to whitespace differences in drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
| * [SCSI] ipr: Fix a race on multiple configuration changesKleber Sacilotto de Souza2011-02-181-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | In a multiple configuration change scenario a remove notification can be followed by an immediate add notification for the same device, which will cause the device to be removed but never added back. This patch fixes the problem by ensuring that in such situations the device will be added back. Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
| * [SCSI] remove flush_scheduled_work() usagesTejun Heo2011-02-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Simple conversions to drop flush_scheduled_work() usages in drivers/scsi. More involved ones will be done in separate patches. * NCR5380, megaraid_sas: cancel_delayed_work() + flush_scheduled_work() -> cancel_delayed_work_sync(). * mpt2sas_scsih: drop unnecessary flush_scheduled_work(). * arcmsr_hba, ipr, pmcraid: flush the used work explicitly instead of using flush_scheduled_work(). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* | libata: remove ATA_FLAG_NO_LEGACYSergei Shtylyov2011-03-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | All checks of ATA_FLAG_NO_LEGACY have been removed by the commits c791c30670ea61f19eec390124128bf278e854fe ([libata] minor PCI IDE probe fixes and cleanups) and f0d36efdc624beb3d9e29b9ab9e9537bf0f25d5b (libata: update libata core layer to use devres), so I think it's time to finally get rid of this flag... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | libata: remove ATA_FLAG_MMIOSergei Shtylyov2011-03-021-2/+1
| | | | | | | | | | | | | | | | | | Commit 0d5ff566779f894ca9937231a181eb31e4adff0e (libata: convert to iomap) removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself. Do it now, at last... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | libata: remove ATA_FLAG_{SRST|SATA_RESET}Sergei Shtylyov2011-03-021-2/+2
| | | | | | | | | | | | | | | | | | These flags are marked as obsolete and the checks for them have been removed by commit 294440887b32c58d220fb54b73b7a58079b78f20 (libata-sff: kill unused ata_bus_reset()), so I think it's time to finally get rid of them... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | ipr/sas_ata: use mode mask macros from <linux/ata.h>Sergei Shtylyov2011-03-021-3/+3
|/ | | | | | | | | Commit 14bdef982caeda19afe34010482867c18217c641 ([libata] convert drivers to use ata.h mode mask defines) didn't convert these two libata driver outside drivers/ata/... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Merge branch 'linux-next' of ↵Linus Torvalds2011-01-141-7/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI/PM: Report wakeup events before resuming devices PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events PCI: sysfs: Update ROM to include default owner write access x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available PCI/ACPI: Request _OSC control once for each root bridge (v3) PCI: enable pci=bfsort by default on future Dell systems PCI/PCIe: Clear Root PME Status bits early during system resume PCI: pci-stub: ignore zero-length id parameters x86/PCI: irq and pci_ids patch for Intel Patsburg PCI: Skip id checking if no id is passed PCI: fix __pci_device_probe kernel-doc warning PCI: make pci_restore_state return void PCI: Disable ASPM if BIOS asks us to PCI: Add mask bit definition for MSI-X table PCI: MSI: Move MSI-X entry definition to pci_regs.h Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the meantime been converted to not use legacy PCI power management, and thus no longer use pci_restore_state() at all (and that caused trivial conflicts with the "make pci_restore_state return void" patch)
| * PCI: make pci_restore_state return voidJon Mason2010-12-231-7/+1
| | | | | | | | | | | | | | | | | | | | | | pci_restore_state only ever returns 0, thus there is no benefit in having it return any value. Also, a large majority of the callers do not check the return code of pci_restore_state. Make the pci_restore_state a void return and avoid the overhead. Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* | Merge branch 'upstream-linus' of ↵Linus Torvalds2011-01-101-1/+1
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies. pata_hpt37x: actually limit HPT370 to UltraDMA/66 pata_hpt3x2n: coding style cleanup pata_hpt37x: coding style cleanup pata_hpt366: coding style cleanup pata_hpt3x2n: calculate average f_CNT pata_hpt3x2n: clarify about HPT371N support pata_hpt{37x|3x2n}: SATA mode filtering [libata] avoid needlessly passing around ptr to SCSI completion func [libata] new driver acard_ahci, for ATP8620 host controller
| * | [libata] avoid needlessly passing around ptr to SCSI completion funcJeff Garzik2011-01-051-1/+1
| |/ | | | | | | | | | | | | It's stored in struct scsi_cmnd->scsi_done, making several 'done' parameters to functions redundant. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | [SCSI] ipr: fix mailbox register definition and add a delay before readingWayne Boyer2010-12-211-6/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | The definition for the mailbox register for new adapters was incorrect. The value has been updated to the correct offset. After an adapter reset, the mailbox register on the new adapters takes a number of seconds to stabilize. A delay has been added before reading the register. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* | [SCSI] ipr: fix lun assignment and comparisonWayne Boyer2010-12-211-4/+3
|/ | | | | | | | | | | | | | The lun value was not getting set up correctly for all devices attached to the new 64 bit adapters. The fix is to move the logic to earlier in the ipr_init_res_entry routine such that the value does get set correctly for all devices. Then the ipr_is_same_device comparison function was using the wrong lun value in the logic for the new adapters. Change this to use the correct lun value. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* SCSI host lock push-downJeff Garzik2010-11-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Move the mid-layer's ->queuecommand() invocation from being locked with the host lock to being unlocked to facilitate speeding up the critical path for drivers who don't need this lock taken anyway. The patch below presents a simple SCSI host lock push-down as an equivalent transformation. No locking or other behavior should change with this patch. All existing bugs and locking orders are preserved. Additionally, add one parameter to queuecommand, struct Scsi_Host * and remove one parameter from queuecommand, void (*done)(struct scsi_cmnd *) Scsi_Host* is a convenient pointer that most host drivers need anyway, and 'done' is redundant to struct scsi_cmnd->scsi_done. Minimal code disturbance was attempted with this change. Most drivers needed only two one-line modifications for their host lock push-down. Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Acked-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [SCSI] ipr: add definitions for a new adapterWayne Boyer2010-10-251-0/+2
| | | | | | | | | There was an addition to the hardware roadmap that includes a new adapter. This patch adds the new definitions for the adapter. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix array error loggingWayne Boyer2010-10-071-5/+5
| | | | | | | | | | | The structure definitions for reporting array errors did not have the correct size for the Array WWID field. This patch fixes those definitions. It also fixes part of the output formatting that did not have newlines and fixes size calculations. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: reverse the isr optimization changesWayne Boyer2010-09-091-30/+33
| | | | | | | | | | | | | | | | | | The isr optimization patch that was submitted a few months ago exposed problems with receiving and handling spurious HRRQ interrutps. commit 64ffdb762241c0a9c0c8fac7ea92aa0ba1529334 Author: Wayne Boyer <wayneb@linux.vnet.ibm.com> Date: Wed May 19 11:56:13 2010 -0700 [SCSI] ipr: improve interrupt service routine performance That patch is reverted with this one. A new patch will be submitted once the issue is better understood and properly handled in the driver. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix resource address formatting and add attribute for device IDWayne Boyer2010-09-051-1/+42
| | | | | | | | | | | This patch fixes a resource address formatting problem where the first byte was being zeroed out. Also, the device ID is now made available as a sysfs attribute. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix resource type update and add sdev and shost attributesWayne Boyer2010-07-281-2/+68
| | | | | | | | | | | | | | | | | Setting the resource type in the ipr_update_res_entry function was incorrect in that the top 4 bits were masked off. The assignment has been updated to no longer mask those bits. Then, two new attributes were added to allow the user space utilities to more easily get information. The resource_type sdev attribute is set for all devices in the adapter's configuration table and indicates the type of device. The fw_type shost attribute indicates the firmware type supported by the adapter. Finally, the resource_path attribute was changed to be mode S_IRUGO. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix transition to operational for new adaptersWayne Boyer2010-07-281-6/+9
| | | | | | | | | | | | | | | | | | The method of transitioning to operational for new adapters includes using initialization stages. The current stage is indicated via a register read. The final good stage in the sequence is "operational" but does not necessarily indicate that the driver can proceed. There is another bit that gets set in the adapter->host interrupt register when the adapter has completed enough of its bringup such that it can accept commands. The driver was not checking that bit before proceeding which led to intermittent errors and adapter resets. The fix is to check the "transition to operational" bit in the interrupt register after detecting that the initialization stage is "operational" and only proceed if both are set. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add support for new Obsidian-E embedded adapterWayne Boyer2010-07-271-0/+2
| | | | | | | | | | This patch allows the driver to recognize a new Obsidian-E based adapter that uses a new subsystem ID. This patch also fixes a few tab/space problems. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add MMIO write to perform BIST for 64 bit adaptersWayne Boyer2010-07-271-16/+21
| | | | | | | | | The 64 bit chip used in new adapters does not properly support the BIST register in PCI config space. This patch implements an alternative MMIO write reset method. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: move setting of the allow_restart flag for vsets and disksWayne Boyer2010-07-271-3/+2
| | | | | | | | | | | | | | | | | | | | A problem was found where the call to scsi_add_device() fails intermittently for an adapter. This is caused when __scsi_add_device() returns -ENODEV as a result of not calling scsi_probe_and_add_lun() since the call to scsi_host_scan_allowed() fails. scsi_host_scan_allowed() fails because the adapter state is set to SHOST_RECOVERY instead of SHOST_RUNNING. The state of the adapter is being set to SHOST_RECOVERY by scsi_eh_scmd_add() during error handling. This problem is avoided by moving the setting of the allow_restart flag to later in the device initialization sequence. This prevents further error handling if we get a NOT_READY response from a TUR command by causing scsi_check_sense() to return SUCCESS. Therefore, scsi_eh_scmd_add() will not run and the adapter state will remain as SHOST_RUNNING. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add endian swap enablement for 64 bit adaptersWayne Boyer2010-07-271-2/+17
| | | | | | | | | | | | | | | | | | | A change in the hardware design of the chip for the new adapters changes the default endianness of MMIO operations. This patch adds a register definition which when written to with a predefined value will change the endianness back to what the driver expects. This patch also fixes two problems found during testing. First, the first reserved field in the ipr_hostrcb64_fabirc_desc structure only reserved one byte. The correct amount to reserve is 2 bytes. Second, the reserved field of the ipr_hostrcb64_error structure only reserved 2 bytes. The correct amount to reserve is 16 bytes. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix resource path display and formattingWayne Boyer2010-07-211-18/+33
| | | | | | | | | | | | | | It was possible to overflow the buffer used to print out the formatted version of the resource path. The fix is to limit the number of bytes that get formatted. This patch also updates the ipr_show_resource_path function to display the resource address for devices that are attached to adapters that don't support resource paths. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: improve interrupt service routine performanceWayne Boyer2010-05-241-33/+30
| | | | | | | | | | | | | During performance testing on P7 machines it was observed that the interrupt service routine was doing unnecessary MMIO operations. This patch rearranges the logic of the routine and moves some of the code out of the main routine. The result is that there are now fewer MMIO operations in the performance path of the code. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: set the data list length in the request control blockWayne Boyer2010-05-241-0/+2
| | | | | | | | | | | | In bring up testing for the new 64 bit adapters, the first read command failed after loading the driver. The cause was that the command requires more than one scatter gather element and the corresponding code to set the data list length in the request control block was missing. This patch adds the correct assignment. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: fix a register read to use the correct address for 64 bit adaptersWayne Boyer2010-05-241-4/+8
| | | | | | | | | | | | | | | | Fix ipr_reset_enable_ioa() to read the correct IOA to host interrupt register address for 64 bit adapters. We need to read the lower 32 bits, not the upper 32 bits. Also change the write of the 64 bit mask value to a single writeq instead of two writel calls. Finally, use the correct u8 type for the type field in the ipr_resource_entry structure. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: include the resource path in the IOA status area structureWayne Boyer2010-05-241-57/+74
| | | | | | | | | | The IOA status area now includes the new resource path field for 64 bit adapters. This patch changes the driver to fix the ioasa structure and to use the correct structure definition based on the type of adatper. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: implement fixes for 64 bit adapter supportWayne Boyer2010-05-241-4/+9
| | | | | | | | | Implement some small fixes for 64 bit support that were preventing the adapter from becoming operational. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* sysfs: add struct file* to bin_attr callbacksChris Wright2010-05-211-3/+6
| | | | | | | | | This allows bin_attr->read,write,mmap callbacks to check file specific data (such as inode owner) as part of any privilege validation. Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* libata: kill ATA_FLAG_DISABLEDTejun Heo2010-05-171-3/+3
| | | | | | | | | | | | | | | | | | | | ATA_FLAG_DISABLED is only used by drivers which don't use ->error_handler framework and is largely broken. Its only meaningful function is to make irq handlers skip processing if the flag is set, which is largely useless and even harmful as it makes those ports more likely to cause IRQ storms. Kill ATA_FLAG_DISABLED and makes the callers disable attached devices instead. ata_port_probe() and ata_port_disable() which manipulate the flag are also killed. This simplifies condition check in IRQ handlers. While updating IRQ handlers, remove ap NULL check as libata guarantees consecutive port allocation (unoccupied ports are initialized with dummies) and long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo2010-03-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* [SCSI] ipr: adds PCI ID definitions for new adaptersWayne Boyer2010-03-031-7/+19
| | | | | | | | | | | | This patch adds the PCI ID definitions for new adapters based on the next generation 64 bit IOA PCI interface chip. New entries have been added to the ipr_pci_table[] array for the adapters and to the ipr_chip[] array for the new versions of the chip. Older entries have been removed for cards that did not ship. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add support for new IOASCsWayne Boyer2010-03-031-0/+32
| | | | | | | | This patch adds support for new errors that can be received from adapters using the next generation 64 bit IOA PCI interface chip. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add support for multiple stages of initializationWayne Boyer2010-03-031-30/+155
| | | | | | | | | This patch adds support for using the new IOA initialization feedback register. It also enables 64 bit support in the ipr_ioafp_identify_hrrq and ipr_mask_and_clear_interrupts routines. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: implement shutdown changes and remove obsolete write cache parameterWayne Boyer2010-03-031-143/+65
| | | | | | | | | | | | This patch adds a reboot notifier that will issue a shutdown prepare command to all adapters. This helps to prevent a problem where the primary adapter can get shut down before the secondary adapter and cause the secondary adapter to fail over and log and error. This patch also removes the "enable_cache" paramater as it is obsolete. Write cache for an adapter is now controlled from the iprconfig utility. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add hardware assisted smart dump functionalityWayne Boyer2010-03-031-16/+65
| | | | | | | | | This patch adds the hardware assisted smart dump functionality for the next generation IOA PCI interface chip. Signea-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add error handling updates for the next generation chipWayne Boyer2010-03-031-10/+247
| | | | | | | Add support for the new log data notification and overlay IDs. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: update the configuration table code for the next generation chipWayne Boyer2010-03-031-96/+416
| | | | | | | | | | | | This patch changes the configuration table structures and related code such that both 32 bit and 64 bit based adapters can work with the driver. This patch also implements the code to generate the virtual bus/id/lun values for devices connected to the new adapters. It also implements support for the new device resource path. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: define new offsets to registers for the next generation chipWayne Boyer2010-03-031-0/+15
| | | | | | | | This patch adds the entry to the ipr_chip_cfg array that defines the register offsets for the next generation 64 bit IOA PCI interface chip. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] ipr: add support for new adapter command structures for the next ↵Wayne Boyer2010-03-031-113/+337
| | | | | | | | | | generation chip Change the adapter command structures such that both 32 bit and 64 bit based adapters can work with the driver. Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectorsMartin K. Petersen2010-02-261-1/+1
| | | | | | | | | | | | | The block layer calling convention is blk_queue_<limit name>. blk_queue_max_sectors predates this practice, leading to some confusion. Rename the function to appropriately reflect that its intended use is to set max_hw_sectors. Also introduce a temporary wrapper for backwards compability. This can be removed after the merge window is closed. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds2009-12-171-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (40 commits) [SCSI] 3w-9xxx fix bug in sgl loading [SCSI] fcoe, libfc: adds enable/disable for fcoe interface [SCSI] libfc: reduce hold time on SCSI host lock [SCSI] libfc: remote port gets stuck in restart state without really restarting [SCSI] pm8001: misc code cleanup [SCSI] pm8001: enable read HBA SAS address from VPD [SCSI] pm8001: do not reset local sata as it will not be found if reset [SCSI] pm8001: bit set pm8001_ha->flags [SCSI] pm8001:fix potential NULL pointer dereference [SCSI] pm8001: set SSC down-spreading only to get less errors on some 6G device. [SCSI] pm8001: fix endian issues with SAS address [SCSI] pm8001: enhance error handle for IO patch [SCSI] pm8001: Fix for sata io circular lock dependency. [SCSI] hpsa: add driver for HP Smart Array controllers. [SCSI] cxgb3i: always use negative errno in case of error [SCSI] bnx2i: minor code cleanup and update driver version [SCSI] bnx2i: Task management ABORT TASK fixes [SCSI] bnx2i: update CQ arming algorith for 5771x chipsets [SCSI] bnx2i: Adjust sq_size module parametr to power of 2 only if a non-zero value is specified [SCSI] bnx2i: Add 5771E device support to bnx2i driver ...
OpenPOWER on IntegriCloud