summaryrefslogtreecommitdiffstats
path: root/drivers/regulator/tps65217-regulator.c
Commit message (Collapse)AuthorAgeFilesLines
* regulator: tps65217: Allow DCDC1 and DCDC3 up to 3.3VMåns Andersson2017-01-231-2/+4
| | | | | | | | | | The data sheet statement that DCDC1 and DCDC3 only can be set in the range 0.9V - 1.5V refers to storage on its internal EEPROM and therefore cold boot configuration. After power-on the device can be reconfigured over i2c and DCDC1/3 set up to 3.3V. Signed-off-by: Måns Andersson <mans.andersson@nibe.se> Signed-off-by: Mark Brown <broonie@kernel.org>
* regulator: tps65217: Enable suspend configurationRuss Dill2016-06-271-9/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The TPS65217 has a pre-defined power-up / power-down sequence which in a typical application does not need to be changed. However, it is possible to define custom sequences under I2C control. The power-up sequence is defined by strobes and delay times. Each output rail is assigned to a strobe to determine the order in which the rails are enabled. Every regulator of tps65217 PMIC has sequence registers and every regulator has a default strobe value and gets disabled when a particular power down sequence occurs. To keep a regulator on during suspend we write value 0 to strobe so that the regulator is out of all sequencers and is not impacted by any power down sequence. Hence saving the default strobe value during probe so that when we want to regulator to be enabled during suspend we write 0 to strobe and when we want it to get disabled during suspend we write the default saved strobe value. This allows platform data to specify which power rails should be on or off during RTC only suspend. This is necessary to keep DDR state while in RTC only suspend. Signed-off-by: Russ Dill <Russ.Dill@ti.com> [Enhanced commit log and added dynamic allocation for strobes] Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* regulator: tps65217: Use simplified DT parsingMark Brown2014-09-101-77/+29
| | | | | | Remove a bunch of code in favour of data. Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Remove unused driver_data from of_match tableMark Brown2014-09-091-7/+7
| | | | | | We don't ever reference the driver_data we supply so remove it. Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Remove spurious platform data checkMark Brown2014-09-061-6/+2
| | | | | | | | We should always be able to probe a regulator with no platform data. This will enable readback of current state, though no changes can be made to the device configuration. Signed-off-by: Mark Brown <broonie@kernel.org>
* regulator: tps65217: Fix build warningsSachin Kamat2014-06-241-2/+2
| | | | | | | | | | | rdev_get_id() returns an int. Convert rid to type int to avoid the following warnings: drivers/regulator/tps65217-regulator.c:73:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] drivers/regulator/tps65217-regulator.c:87:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Use regulator_map_voltage_ascend for LDO1Axel Lin2014-04-181-0/+1
| | | | | | | | The voltages in LDO1_VSEL_table are in ascendant order, so use regulator_map_voltage_ascend. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Remove *rdev[] from struct tps65217Axel Lin2014-04-181-3/+0
| | | | | | | | | Now this driver uses devm_regulator_register() so we don't need to save rdev pointer to tps->rdev[i] for cleanup. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Allow missing init_data for diagnosticsAxel Lin2014-03-031-13/+2
| | | | | | | | The regulator core supports this to allow the configuration to be inspected at runtime even if no software management is enabled. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Use of_get_child_by_nameSachin Kamat2014-02-141-1/+1
| | | | | | | | of_find_node_by_name walks the allnodes list, and can thus walk outside of the parent node. Use of_get_child_by_name instead. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
* Merge remote-tracking branch 'regulator/topic/linear' into regulator-nextMark Brown2013-10-241-16/+8
|\
| * regulator: Add REGULATOR_LINEAR_RANGE macroAxel Lin2013-10-111-8/+8
| | | | | | | | | | | | | | Add REGULATOR_LINEAR_RANGE macro and convert regulator drivers to use it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| * regulator: Remove max_uV from struct regulator_linear_rangeAxel Lin2013-10-111-16/+8
| | | | | | | | | | | | | | | | | | linear ranges means each range has linear voltage settings. So we can calculate max_uV for each linear range in regulator core rather than set the max_uV field in drivers. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* | regulator: tps65217: Use devm_regulator_registerSachin Kamat2013-09-171-22/+4
|/ | | | | | | devm_* simplifies the code. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: tps65217: Convert to use linear rangesAxel Lin2013-08-301-145/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Below is the equation in original code: tps65217_uv1_ranges: 0 ... 24: uV = vsel * 25000 + 900000; 25 ... 52: uV = (vsel - 24) * 50000 + 1500000; = (vsel - 25) * 50000 + 1550000; 53 ... 55: uV = (vsel - 52) * 100000 + 2900000; = (vsel - 53) * 100000 + 3000000; 56 ... 62: uV = 3300000; tps65217_uv2_ranges: 0 ... 8: uV = vsel * 50000 + 1500000; 9 ... 13: uV = (vsel - 8) * 100000 + 1900000; = (vsel - 9) * 100000 + 2000000; 14 ... 31: uV = (vsel - 13) * 50000 + 2400000; = (vsel - 14) * 50000 + 2450000; The voltage tables are composed of linear ranges. This patch converts this driver to use multiple linear ranges APIs. In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52. This change makes it possible to reuse the same linear_ranges table for DCDCx. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* regulator: Remove all platform_set_drvdata(pdev, NULL) in driversAxel Lin2013-05-121-2/+0
| | | | | | | | | Since 0998d06310 "device-core: Ensure drvdata = NULL when no driver is bound", this is done by driver core after device_release or on probe failure. Thus we can remove all platform_set_drvdata(pdev, NULL) in drivers. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Fix using wrong dev argument for calling of_regulator_matchAxel Lin2013-01-241-2/+2
| | | | | | | | | | | | The dev parameter is the device requestiong the data. In this case it should be &pdev->dev rather than pdev->dev.parent. The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(), which means this fixes a memory leak because the memory is allocated every time probe() is called, thus it should be freed when this driver is unloaded. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devexitBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devinitBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: remove use of __devexit_pBill Pemberton2012-11-201-1/+1
| | | | | | | | CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* mfd: Move tps65217 regulator plat data handling to regulatorAnilKumar Ch2012-08-221-15/+109
| | | | | | | | | | | | | | | | | | | | | Regulator platform data handling was mistakenly added to MFD driver. So we will see build errors if we compile MFD drivers without CONFIG_REGULATOR. This patch moves regulator platform data handling from TPS65217 MFD driver to regulator driver. This makes MFD driver independent of REGULATOR framework so build error is fixed if CONFIG_REGULATOR is not set. drivers/built-in.o: In function `tps65217_probe': tps65217.c:(.devinit.text+0x13e37): undefined reference to `of_regulator_match' This patch also fix allocation size of tps65217 platform data. Current implementation allocates a struct tps65217_board for each regulator specified in the device tree. But the structure itself provides array of regulators so one instance of it is sufficient. Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
* regulator: tps65217: Add device tree supportAnilKumar Ch2012-07-121-0/+1
| | | | | | | | | This commit adds device tree support for tps65217 pmic. And usage details are added to device tree documentation. Driver is tested by using kernel module with regulator set and get APIs. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Fix voltage boundary checking in tps65217_pmic_map_voltageAxel Lin2012-07-031-3/+3
| | | | | | | | | | | | | | It is ok to request voltage with min_uV < tps->info[rid]->min_uV and max_uV > tps->info[rid]->max_uV. The equation we used in uv_to_vsel() does not allow min_uV < tps->info[rid]->min_uV, otherwise it returns negative selector. So we need to set min_uV = tps->info[rid]->min_uV if min_uV < tps->info[rid]->min_uV. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: invalid if checkAlan Cox2012-07-021-2/+2
| | | | | | | | | This permits the setting of bogus values because the invalidity check is itself invalid. Reported-by: dcb314@hotmail.com Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Convert LDO1 to use regulator_list_voltage_tableAxel Lin2012-07-011-25/+22
| | | | | | | | | | | Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table. We have n_voltages and volt_table settings in regulator_desc, so we don't need the table and table_len fields in struct tps_info. Thus remove them from struct tps_info. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Convert to regulator_[is_enabled|get_voltage_sel]_regmapAxel Lin2012-06-131-72/+42
| | | | | | | | | | | | | | | This patch converts .is_enabled and .get_voltage_sel to regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap. For .enable, .disable, and .set_voltage_sel, the write protect level is either 1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap. Now we store the enable reg/mask and vsel reg/mask in regulator_desc, so we can remove enable_mask, set_vout_reg, and set_vout_mask from struct tps_info. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Convert to set_voltage_sel and map_voltageAxel Lin2012-05-181-38/+30
| | | | | | | | | | Convert tps65217_pmic_ops to use set_voltage_sel and map_voltage. After this convertion, we can also use tps65217_pmic_set_voltage_sel() for set_voltage_sel callback of tps65217_pmic_ldo1_ops. Thus this patch also removes tps65217_pmic_ldo1_set_voltage_sel() function. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: core: Use a struct to pass in regulator runtime configurationMark Brown2012-04-091-2/+6
| | | | | | | | | | | | | | Rather than adding new arguments to regulator_register() every time we want to add a new bit of dynamic information at runtime change the function to take these via a struct. By doing this we avoid needing to do further changes like the recent addition of device tree support which required each regulator driver to be updated to take an additional parameter. The regulator_desc which should (mostly) be static data is still passed separately as most drivers are able to configure this statically at build time. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Constify regulator_descAxel Lin2012-04-061-1/+1
| | | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Merge tps65217_pmic_ldo234_ops and tps65217_pmic_dcdc_ops to ↵Axel Lin2012-03-121-187/+72
| | | | | | | | | | | | | | tps65217_pmic_ops Most callback functions implementation for tps65217_pmic_ldo234_ops and tps65217_pmic_dcdc_ops are the same except the rid range checking. This patch uses tps65217_pmic_ops for all DCDCx, LDO2, LDO3, and LDO4. And rework tps65217_pmic_set_voltage to make it can be called for DCDCx, LDO2, LDO3, and LDO4. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Use DIV_ROUND_UP macro to calculate selectorAxel Lin2012-03-111-6/+6
| | | | | | | Use DIV_ROUND_UP macro for better readability. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Update tps65217-regulator for DT changesAxel Lin2012-01-201-1/+1
| | | | | Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: tps65217: Add tps65217 regulator driverAnilKumar Ch2012-01-201-0/+493
This patch adds tps65217 PMIC as a regulator The regulator module consists of 3 DCDCs and 4 LDOs. The output voltages are configurable and are meant to supply power to the main processor and other components Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OpenPOWER on IntegriCloud