summaryrefslogtreecommitdiffstats
path: root/drivers/regulator/Kconfig
Commit message (Collapse)AuthorAgeFilesLines
* LP3971 PMIC regulator driver (updated and combined version)Marek Szyprowski2009-06-151-0/+7
| | | | | | | | | | | This patch adds regulator drivers for National Semiconductors LP3971 PMIC. This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface. Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: add userspace-consumer driverMike Rapoport2009-06-151-0/+10
| | | | | | | | | | | The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Maxim 1586 regulator driverRobert Jarzmik2009-06-151-0/+9
| | | | | | | | | | | | | | The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: twl4030 regulatorsDavid Brownell2009-03-311-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Support most of the LDO regulators in the twl4030 family chips. In the case of LDOs supporting MMC/SD, the voltage controls are used; but in most other cases, the regulator framework is only used to enable/disable a supplies, conserving power when a given voltage rail is not needed. The drivers/mfd/twl4030-core.c code already sets up the various regulators according to board-specific configuration, and knows that some chips don't provide the full set of voltage rails. The omitted regulators are intended to be under hardware control, such as during the hardware-mediated system powerup, powerdown, and suspend states. Unless/until software hooks are known to be safe, they won't be exported here. These regulators implement the new get_status() operation, but can't realistically implement get_mode(); the status output is effectively the result of a vote, with the relevant hardware inputs not exposed. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Make fixed voltage regulators visible in KconfigMark Brown2009-03-311-1/+5
| | | | | | | | | This allows users to enable or disable support for these regulators at build time as they can for other regulators rather than having platforms force the regulators to be built in. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: PCF50633 pmic driverBalaji Rao2009-01-111-0/+7
| | | | | | | | | | | Changes from V1: - Removed support for suspend_enable & suspend_disable functions. Signed-off-by: Balaji Rao <balajirrao@openmoko.org> Cc: Andy Green <andy@openmoko.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
* regulator: Use menuconfig in KconfigTakashi Iwai2008-11-091-11/+4
| | | | | | | | | Use menuconfig instead of flat configs so that you can disable/enable regulator items with one selection. Also, use depends instead of reverse selections to make life easier, too. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* da903x: add regulator support for DA9030/DA9034Eric Miao2008-10-131-0/+8
| | | | | | Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Liam Girdwood <lrg@kernel.org>
* regulator: Add WM8350 regulator supportMark Brown2008-10-131-0/+9
| | | | | | | | | | | | The WM8350 features six DCDC convertors (four buck and two boost), four LDO voltage regulators and two constant current sinks. This driver adds support for these through the regulator API. This driver was written by Liam Girdwood with updates for submission from Mark Brown. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add WM8400 regulator supportMark Brown2008-10-131-0/+7
| | | | | | | | | | | | The WM8400 provides two programmable DCDC step-down (buck) convertors and four low-dropout (LDO) regulators. This driver provides support for runtime managment of these in the standard regulator API. Support for configuration of the suspend and hibernate mode behaviour of the regulators is not yet included. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: TI bq24022 Li-Ion Charger driverPhilipp Zabel2008-07-301-0/+10
| | | | | | | | This adds a regulator driver for the TI bq24022 Single-Chip Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
* regulator: core kbuild filesLiam Girdwood2008-07-301-0/+49
This patch adds kernel build support for the regulator core. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
OpenPOWER on IntegriCloud