| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d687 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c9836c ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
|
| | |
| |
| |
| |
| | |
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This adds pinctrl driver for SPEAr13xx family. SPEAr13xx family supports two
machines: SPEAr1310 and SPEAr1340.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Same GPIO pins declarations would be required for other SoCs and that will be a
lot of lines of code. Its better to create common macros for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The nomadik gpio code has been converted to pinctrl, but the nomadik platform
still expects the old code to be present. Change it to use the new one instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This implements the pin configuration interface for the
Nomadik pin controller.
As part of the exercise we add a bit in the pin_cfg_t for
the Nomadik pinctrl driver that indicates if the pin should
be forced into GPIO mode. This is not done to go behind the
back of the GPIO subsystem, but to ensure that default modes
can be set by hogs on boot and system suspend/resume states.
It was used implicitly by the old code defining all config
settings and modes in a single config word but we now have
a split between pinmux and pinconf leading to the need to
have this.
We also add a bit for explicitly setting sleepmode of the
pin. This was previously handled by custom calls with the
_sleep() suffix, but we now have one single interface into
the configuration so we replace this with a bit indicating
that the pin shall be configured into sleep mode.
Some of the configuration can be refactored later to use
less custom fields on the pin_cfg_t but we are currently
leaving the old function calls in place so we stay
compatible.
ChangeLog v1->v2:
- Drop a hunk changing pinmuxing for GPIO and move it
over to the preceding pinmux patch.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Implements basic pinmux for the Nomadik pin controller.
The plan is to split the existing singular pin config interface
nmk_config_pin(), nmk_config_pins(), that will configure muxing
and other settings at the same time, into two interfaces
by splitting the code in pinmux and pinctrl and eventually
deleting the old interface and its helper functions when all
users are gone.
nmk_gpio_set_mode() and nmk_gpio_get_mode() are two older
interfaces for just configuring muxing/altfunctions that
will also be replaced in the end.
We take some extra care to handle the glitch-avoidance here,
but it is simpler now since there is only one altsetting per
pingroup so we know immediately if we need to avoid altfunc
C glitches for a certain group.
As part of the makeover implement the .request() and .free()
calls on the GPIO chips and have them call back into the
pinctrl layer to reserve GPIOs.
ChangeLog v1->v2:
- Rebased on pinctrl-mergebase-20120418 so we get the latest
driver infrastructure where function count is done by a fixed
value and we can drop a few range checks since this is now
handled by the core.
- Include a GPIO muxing hunk erroneously part of the pin config
patch.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since all pins we can control are GPIOs, match a GPIO range to
each pin in the debug function and call into the GPIO debug
print function to have the per-pin information.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Break out the code displaying the status of a single pin so we
can use the same code in the pinctrl debug function.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
a60b57e "drivers/gpio: gpio-nomadik: Add support for irqdomains" broke
building with CONFIG_OF_GPIO disabled.
Without this patch, building nhk8815_defconfig results in:
/home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c: In function 'nmk_gpio_probe':
/home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c:1238:6: error: 'struct gpio_chip' has no member named 'of_node'
make[3]: *** [drivers/gpio/gpio-nomadik.o] Error 1
make[2]: *** [drivers/gpio] Error 2
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [drivers] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
I'm moving this driver over to the pinctrl subsystem to convert
the custom pin mux/config scheme over to use pinctrl.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |\ \ \
| | | |/
| | |/|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* spear/pinctrl:
pinctrl: (cosmetic) fix two entries in DocBook comments
pinctrl: add more info to error msgs in pin_request
CLKDEV: provide helpers for common clock framework
pinctrl: add pinctrl-mxs support
pinctrl: pinctrl-imx: add imx6q pinctrl driver
pinctrl: pinctrl-imx: add imx pinctrl core driver
dt: add of_get_child_count helper function
pinctrl: support gpio request deferred probing
pinctrl: add pinctrl_provide_dummies interface for platforms to use
pinctrl: enhance reporting of errors when loading from DT
pinctrl: add kerneldoc for pinctrl_ops device tree functions
pinctrl: propagate map validation errors
pinctrl: fix dangling comment
pinctrl: fix signed vs unsigned conditionals inside pinmux_map_to_setting
ARM: 7392/1: CLKDEV: Optimize clk_find()
ARM: 7376/1: clkdev: Implement managed clk_get()
This just adds more dependencies that are required in order not to
break the spear pinctrl support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | |
| | | | \ | |
| | | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
spear/pinctrl
The spear/pinctrl branch has hard dependencies on both the
pinctrl branch and the clkdev branch. We merge those here
to fix it up without having to rebase a branch that has
been pulled into other stable branches already.
Conflicts:
Documentation/driver-model/devres.txt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/pinctrl
By Stephen Warren
via Stephen Warren
* 'for-3.5/gpio-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
pinctrl: tegra: error reporting cleanup
pinctrl: tegra: debugfs enhancements
pinctrl: tegra: refactor probe handling
ARM: dt: tegra20: add pinmux to device tree
ARM: dt: tegra cardhu: add pinmux to device tree
ARM: tegra: Remove pre-pinctrl pinmux driver
ARM: tegra: Switch to new pinctrl driver
gpio: tegra: Hide tegra_gpio_enable/disable()
ARM: tegra: seaboard: Don't gpio_request() ISL29018_IRQ
gpio: tegra: configure pins during irq_set_type
ARM: tegra: Remove VBUS_GPIO handling from board files
usb: ehci-tegra: Add vbus_gpio to platform data
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Print an explicit error message in various failure cases to allow
easier diagnosis.
WARN_ON() some internal failures that users/clients shouldn't be able to
trigger.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
* Only provide debugfs-relates ops when CONFIG_DEBUG_FS is enabled.
* Implement pin_config_group_dbg_show op.
* Implement pin_config_config_dbg_show op.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.
This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |_|_|/
| | |/| | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
* Rename old pinmux and new pinctrl platform driver and DT match table
entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
in pinctrl format.
Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.
All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.
Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.
Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
|
| | |\ \ \ \ \
| | |/ / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next/pinctrl
By Stephen Warren (12) and others
via Linus Walleij
* tag 'pinctrl-mergebase-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (24 commits)
pinctrl: show pin name for pingroups in sysfs
pinctrl: show pin name when request pins
pinctrl: implement devm_pinctrl_get()/put()
pinctrl: a minor fix of pin config debug information
pinctrl: pinconf: fix compilation error if PINCONF is not selected
pinctrl: allow pctldevs to decode pin config in debugfs
pinctrl: ifdef CONFIG_DEBUG_FS cleanup
pinctrl: mark non-EXPERIMENTAL
pinctrl: tegra: Add complete device tree support
dt: Document Tegra20/30 pinctrl binding
dt: Move Tegra20 pin mux binding into new pinctrl directory
dt: pinctrl: Document device tree binding
dt: add property iteration helpers
pinctrl: implement pinctrl deferred probing
pinctrl: add some error checking for user interfaces
pinctrl: fix pinmux_check_ops error checking
pinctrl: replace list_*() with get_*_count()
pinctrl: mark const init data with __initconst instead of __initdata
Documentation: pinctrl: add missing spi0_0 grp in example
pinctrl: fix build when CONFIG_OF && !CONFIG_PINCTRL
...
Resolved conflicts in drivers/pinctrl/core.c due to same patch being
applied in two branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |\ \ \ \ \
| | |_|/ / /
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/gpio
Linus Walleij <linus.walleij@linaro.org> writes:
This is a pull request for the GPIO and pin control stuff
accumulated in the ST-Ericsson tree. Here we have:
- Improvements and fixes and a custom pin config API from
Rabin Vincent
- Device Tree bindings from Lee Jones
- Some accumulated patches by yours truly.
- A MSP platform data init patch from Ola Lilja that is merged
here due to dependency on pin config work. It is to be
used with work being worked on in parallel in the ALSA
SoC subsystem.
If you wonder about the custom pin config implementation this
is to be used as a transition base as I am rewriting the
driver to use pinctrl. Expect a final pull request on top
of this one that will move the ux500 over to pinctrl.
* 'ux500-gpio-pins-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Add support for MSP I2S-devices
drivers/gpio: gpio-nomadik: Add support for irqdomains
drivers/gpio: gpio-nomadik: Apply Device Tree bindings
ARM: ux500: update pin handling
ARM: ux500: implement pin API
ARM: ux500: remove a bunch of internal pull-ups
plat-nomadik: new sleep mode pincfg macros
gpio/nomadik: use ioremap() instead of static mappings
gpio/nomadik: support low EMI mode
gpio/nomadik: fix spurious interrupts with SKE
gpio/nomadik: cache [rf]w?imsc
gpio/nomadik: don't set SLPM to 1 for non-wakeup pins
Also includes an update to v3.4-rc4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Most code assumes that the pinctrl ops are present. Validate this when
registering a pinctrl driver. Remove the one place in the code that
was checking whether one of these non-optional ops was present.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This adds pinctrl driver for SPEAr3xx family. SPEAr3xx family supports three
families: SPEAr300, SPEAr310 and SPEAr320.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This adds pinctrl driver for SPEAr platform. It also updates MAINTAINERS file
for SPEAr pinctrl drivers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ChangeLog v1->v2:
* change PIN_FUNC_ID base in binding doc to 0 from 1.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ChangeLog v1->v2:
* change PIN_FUNC_ID base in binding doc to 0 from 1.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some SoCs may not have pinmux disable function in HW.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Also checking invalid num_configs when validate the pinconf map.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The recent added mxs gpio device tree bindings require gpio nodes
defined under pinctrl node too. The pinctrl-mxs driver should skip
these node for group parsing and creating.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The initial mxs pinctrl support, commit 1772311 (pinctrl: add
pinctrl-mxs support) skipped creating group from device tree pin config
node. Add it to get pin config node work for client device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Additionally print which pin the request failed for, which entity already
claimed it, and what entity was trying to claim it.
Remove duplicate device name from a debug message.
Clean up some indentation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add pinctrl support for Freescale MXS SoCs, i.MX23 and i.MX28.
The driver supports device tree probe only.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The driver has mux and config support while the gpio is still
not supported.
For select input setting, the driver will handle it internally
and do not need user to take care of it.
The pinctrl-imx core driver will parse the dts file and dynamically
create the pinmux functions and groups.
Each IMX SoC pinctrl driver should register pins with a pin register map
including mux register and config register and select input map to core
for proper operations.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
As pinctrl handles, it may be possible the pinctrl gpio ranges
are still not got registered when user call pinctrl_gpio_request.
Thus, add defer support for it too.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add a interface pinctrl_provide_dummies for platform to indicate
whether it needs use pinctrl dummy state.
ChangeLog v3->v4:
* remove dummy gpio support in pinctrl subsystem.
Let gpio driver decide whether it wants to use pinctrl gpio mux
function.
ChangeLog v2->v3:
* Also changed the missed pinctrl gpio APIs in v1.
ChangeLog v1->v2:
* Based on sascha's suggestion, drop using kconfig since it will hide
pinctrl errors on all other boards.
See: https://lkml.org/lkml/2012/4/18/282
It seemed both Linus and Stephen agreed with this way, so i'm ok
with it too.
* Add dummy gpio support.
pinctrl gpio in the same situation as state.
* Patch name changed.
Original is pinctrl: handle dummy state in core.
* Split removing old dt dummy interface into a separate patch
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There are a few places in the api where the code simply returns -EINVAL when
it finds an error. An example is pinmux_map_to_setting() which now reports an
error if we try to match a group with a function that it does not support.
The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the
same style and is located inside the according functions and not the calling
code.
When the map is found in the DT but the default state can not be selected we
get an error to know that the code at least tried.
The patch also removes a stray word from one comment and a "->" from another
for the sake of consistency.
Finally we replace a few pr_err/debug() calls with dev_err/dbg().
Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting
inside pinmux_map_to_setting().
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
pinctrl_register_map() was returning early if pinmux_validate_map() or
pinconf_validate_map() failed, but was not actually returning the error
code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
pinmux_map_to_setting() uses setting->data.mux.func/group to store the return
code of pinmux_func_name_to_selector/pinctrl_get_group_selector(). However,
struct pinctrl_setting_mux defines these elements as unsigned, resulting in all
error codes getting lost. The conditionals following the assignments will always
evaluate to false thus breaking the error paths.
This bug can be triggered by loading a pinmux group map from the devicetree
with an invalid function/group string.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pin name is more useful to users.
After change, when cat pingroups in sysfs, it becomes:
root@freescale /sys/kernel/debug/pinctrl/20e0000.iomuxc$ cat pingroups
registered pin groups:
group: uart4grp-1
pin 219 (MX6Q_PAD_KEY_ROW0)
pin 218 (MX6Q_PAD_KEY_COL0)
group: usdhc4grp-1
pin 305 (MX6Q_PAD_SD4_CMD)
pin 306 (MX6Q_PAD_SD4_CLK)
pin 315 (MX6Q_PAD_SD4_DAT0)
pin 316 (MX6Q_PAD_SD4_DAT1)
pin 317 (MX6Q_PAD_SD4_DAT2)
pin 318 (MX6Q_PAD_SD4_DAT3)
pin 319 (MX6Q_PAD_SD4_DAT4)
pin 320 (MX6Q_PAD_SD4_DAT5)
pin 321 (MX6Q_PAD_SD4_DAT6)
pin 322 (MX6Q_PAD_SD4_DAT7)
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Pin name is more useful to users.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
These functions allow the driver core to automatically clean up any
allocations made by drivers, thus leading to simplified drivers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When we compile pinctrl layer for platforms without CONFIG_PINCONF, we get
following compilation errors:
drivers/built-in.o: In function `pinctrl_show':
linux-2.6/drivers/pinctrl/core.c:1116: undefined
reference to `pinconf_show_setting'
drivers/built-in.o: In function `pinctrl_maps_show':
linux-2.6/drivers/pinctrl/core.c:1071: undefined
reference to `pinconf_show_map'
drivers/built-in.o: In function `pinctrl_init_device_debugfs':
linux-2.6/drivers/pinctrl/core.c:1224: undefined
reference to `pinconf_init_device_debugfs'
make[1]: *** [.tmp_vmlinux1] Error 1
This patch fixes this.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Add a pinconf op so that pin controller drivers can decode their pin
config settings for debugfs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
