| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
After searching for the old property, bail out with -ENODEV
if it was not found.
It is unnecessary to check if oldprop is NULL before removing
its binary file; the check was already done before.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In tag next-20140407, building with CONFIG_DEBUG_SECTION_MISMATCH
enabled, the following WARNING is occured:
WARNING: drivers/built-in.o(.text.unlikely+0x2220): Section mismatch
in reference from the function __reserved_mem_check_root() to the
function .init.text:of_get_flat_dt_prop()
The function __reserved_mem_check_root() references
the function __init of_get_flat_dt_prop().
This is often because __reserved_mem_check_root lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: vmlinux.o(.text.unlikely+0xb9d0): Section mismatch in reference
from the function __reserved_mem_check_root() to the (unknown reference)
.init.data:(unknown)
The function __reserved_mem_check_root() references
the (unknown reference) __initdata (unknown).
This is often because __reserved_mem_check_root lacks a __initdata
annotation or the annotation of (unknown) is wrong.
This is cause by :
'drivers: of: add initialization code for dynamic reserved memory'.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull MTD updates from Brian Norris:
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
Fix index regression in nand_read_subpage
mtd: diskonchip: mem resource name is not optional
mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
mtd: omap2: Use devm_ioremap_resource()
mtd: denali_dt: Use devm_ioremap_resource()
mtd: devices: elm: update DRIVER_NAME as "omap-elm"
mtd: devices: elm: configure parallel channels based on ecc_steps
mtd: devices: elm: clean elm_load_syndrome
mtd: devices: elm: check for hardware engine's design constraints
mtd: st_spi_fsm: Succinctly reorganise .remove()
mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
mtd: st_spi_fsm: Avoid duplicating MTD core code
mtd: st_spi_fsm: Remove useless consts from function arguments
mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This commit adds simple helpers to obtain the devicetree properties
that specify the ECC strength and ECC step size to use on a given
NAND controller.
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |\ \
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b283c ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9bf ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e46 ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.
When the ID is given the phy autoprobing is defeated and the phy is
created directly.
This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.
Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell 88E1318)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \
| | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
of_get_phy_mode() uses a local array to map phy_interface_t values from
include/linux/net/phy.h to a string which is read from the 'phy-mode' or
'phy-connection-type' property. In preparation for exposing the PHY
interface mode through sysfs, perform the following:
- mode phy_modes from drivers/of/of_net.c to include/linux/phy.h such
that it is right below the phy_interface_t enum
- make it a static inline function returning the string such that we can
use it by just including include/linux/net/phy.h
- add a PHY_INTERFACE_MODE_MAX enum value to guard the iteration in
of_get_phy_mode()
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
ePAPR 1.1 defines the "stdout-path" property for specifying the console
device, but Linux currently only handles the older "linux,stdout-path"
property. This patch adds parsing for the new property name.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When the reserved memory patches hit -next, several legacy (non-DT) boot
failures were detected and bisected down to that commit. There needs to
be some sanity checking whether a DT is even present before parsing the
reserved ranges.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add support for custom reserved memory drivers. Call their init() function
for each reserved region and prepare for using operations provided by them
with by the reserved_mem->ops array.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This patch adds support for dynamically allocated reserved memory regions
declared in device tree. Such regions are defined by 'size', 'alignment'
and 'alloc-ranges' properties.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This patch adds support for static (defined by 'reg' property) reserved
memory regions declared in device tree.
Memory blocks can be reliably reserved only during early boot. This must
happen before the whole memory management subsystem is initialized,
because we need to ensure that the given contiguous blocks are not yet
allocated by kernel. Also it must happen before kernel mappings for the
whole low memory are created, to ensure that there will be no mappings
(for reserved blocks). Typically, all this happens before device tree
structures are unflattened, so we need to get reserved memory layout
directly from fdt.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
After the move to having device nodes be proper kobjects the lifecycle
of the node needs to be controlled better.
At first convert of_add_node() in the unflattened functions to
of_init_node() which initializes the kobject so that of_node_get/put
work correctly even before of_init is called.
Afterwards introduce of_node_is_initialized & of_node_is_attached that
query the underlying kobject about the state (attached means kobj
is visible in sysfs)
Using that make sure the lifecycle of the tree is correct at all
times.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[grant.likely: moved of_node_init() calls, fixed up locking, and
dropped __of_populate() hunks]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The same data is now available in sysfs, so we can remove the code
that exports it in /proc and replace it with a symlink to the sysfs
version.
Tested on versatile qemu model and mpc5200 eval board. More testing
would be appreciated.
v5: Fixed up conflicts with mainline changes
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Adds a few simple test cases to ensure that addition, update and removal
of device tree node properties works correctly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
| | |/ / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Device tree nodes are already treated as objects, and we already want to
expose them to userspace which is done using the /proc filesystem today.
Right now the kernel has to do a lot of work to keep the /proc view in
sync with the in-kernel representation. If device_nodes are switched to
be kobjects then the device tree code can be a whole lot simpler. It
also turns out that switching to using /sysfs from /proc results in
smaller code and data size, and the userspace ABI won't change if
/proc/device-tree symlinks to /sys/firmware/devicetree/base.
v7: Add missing sysfs_bin_attr_init()
v6: Add __of_add_property() early init fixes from Pantelis
v5: Rename firmware/ofw to firmware/devicetree
Fix updating property values in sysfs
v4: Fixed build error on Powerpc
Fixed handling of dynamic nodes on powerpc
v3: Fixed handling of duplicate attribute and child node names
v2: switch to using sysfs bin_attributes which solve the problem of
reporting incorrect property size.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
| | |\ \ \ \
| | | |_|/
| | |/| |
| | | | | |
Linux 3.14-rc5
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This reverts commit 02ed594e7113644c06ae3a89bc9215d839510efc.
The change is completely broken. It attempt to get the previous item in
a linked list by grabbing the address of a stack variable. Outright
wrong.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Translating an address from a PCI node of the device-tree into a CPU
physical address doesn't require the core PCI support. Those
translations are just related to the device tree itself.
The use case to translate an address from a PCI node without actually
using the PCI core support is when one needs to access the PCI
controller without accessing any PCI devices.
Marvell SoCs, such as Kirkwood, Dove or Armada XP for instance, come
with an IP of a PCI controller. In the registers of this controller
are stored the ID and the revision of a SoC. With this patch it will
be possible to read the SoC ID of a board without any PCI device and
then without the PCI core support.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The of_update_property() is intented to update a property in a node
and if the property does not exist, will add it.
The second search of the property is possibly won't be found, that
maybe removed by other thread just before the second search begain.
Using the __of_find_property() and __of_add_property() instead and
move them into lock operations.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There two places will use the same code for adding one new property to
the DT node. Adding __of_add_property() and prepare for fixing
of_update_property()'s bug.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When attaching a node always clear the detach flag. Without this change
the sequence detach, attach fails.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Per the ePAPR v1.1 specification, 'phy-connection-type' is the canonical
property name for describing an Ethernet to PHY connection type. Make
sure that of_get_phy_mode() also attempts to parse that property and
update the comments mentioning 'phy-mode' to also include
'phy-connection-type'.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If of_graph_parse_endpoint is given a parentless node instead of an
endpoint node, it is clearly a bug.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch adds a new struct of_endpoint which is then embedded in struct
v4l2_of_endpoint and contains the endpoint properties that are not V4L2
(or even media) specific: the port number, endpoint id, local device tree
node and remote endpoint phandle. of_graph_parse_endpoint parses those
properties and is used by v4l2_of_parse_endpoint, which just adds the
V4L2 MBUS information to the containing v4l2_of_endpoint structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
A 'return endpoint;' at the end of the (!prev) case allows to
reduce the indentation level of the (prev) case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If of_graph_get_next_endpoint is given a parentless node instead of an
endpoint node, it is clearly a bug.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
| | | | | | |
| | \ \ \ | |
| |\ \ \ \ \
| |_|/ / /
|/| | / /
| | |/ /
| |/| | |
'regulator/topic/enable', 'regulator/topic/fan53555', 'regulator/topic/fixed', 'regulator/topic/gpio', 'regulator/topic/lp3971', 'regulator/topic/lp872x' and 'regulator/topic/max14577' into regulator-next
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The need to know the number of array elements in a property is
a common pattern. To prevent duplication of open-coded implementations
add a helper static function that also centralises strict sanity
checking and DTB format details, as well as a set of wrapper functions
for u8, u16, u32 and u64.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
| |\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adds a selftest function for the of_match_node function. of_match_node
is supposed to handle precedence for the compatible property as well as
the name and device_type values. This patch adds some test case data and
a function that makes sure each test node matches against the correct
entry of an of_device_id table.
This code was written to verify the new of_match_node() implementation
that is an earlier part of this series.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Kevin Hao <haokexin@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In the current implementation of __of_match_node(), it will compare
each given match entry against all the node's compatible strings
with of_device_is_compatible().
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and
also an alphabetical ordering is more sane there.
Therefore, we define a following priority order for the match, and
then scan all the entries to find the best match.
1. specific compatible && type && name
2. specific compatible && type
3. specific compatible && name
4. specific compatible
5. general compatible && type && name
6. general compatible && type
7. general compatible && name
8. general compatible
9. type && name
10. type
11. name
v5: Fix nested locking bug
v4: Short-circuit failure cases instead of mucking with score, and
remove extra __of_device_is_compatible() wrapper stub.
Move scoring logic directly into __of_device_is_compatible()
v3: Also need to bail out when there does have a compatible member in match
entry, but it doesn't match with the device node's compatible.
v2: Fix the bug such as we get the same score for the following two match
entries with the empty node 'name2 { };'
struct of_device_id matches[] = {
{.name = "name2", },
{.name = "name2", .type = "type1", },
{}
};
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[grant.likely: added v4 changes]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit 06b29e76a74b2373e6f8b5a7938b3630b9ae98b2.
As pointed out by Grant Likely, we should also take the type and name
into account when searching the best compatible match. That means the
match with compatible, type and name should be better than the match
just with the same compatible string. So revert this and we will
implement another method to find the best match entry.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
| |\ \ \
| |/ /
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking fixes from David Miller:
1) kvaser CAN driver has fixed limits of some of it's table, validate
that we won't exceed those limits at probe time. Fix from Olivier
Sobrie.
2) Fix rtl8192ce disabling interrupts for too long, from Olivier
Langlois.
3) Fix botched shift in ath5k driver, from Dan Carpenter.
4) Fix corruption of deferred packets in TIPC, from Erik Hugne.
5) Fix newlink error path in macvlan driver, from Cong Wang.
6) Fix netpoll deadlock in bonding, from Ding Tianhong.
7) Handle GSO packets properly in forwarding path when fragmentation is
necessary on egress, from Florian Westphal.
8) Fix axienet build errors, from Michal Simek.
9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
Tsirkin.
10) Carrier status isn't set properly in hyperv driver, from Haiyang
Zhang.
11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.
12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
queue selection method. Add a fallback method mechanism to fix this
bug, from Daniel Borkmann.
13) Fix regression in link local route handling on GRE tunnels, from
Nicolas Dichtel.
14) Bonding can assign dup aggregator IDs in some sequences of
configuration, fix by making the allocation counter per-bond instead
of global. From Jiri Bohac.
15) sctp_connectx() needs compat translations, from Daniel Borkmann.
16) Fix of_mdio PHY interrupt parsing, from Ben Dooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
MAINTAINERS: add entry for the PHY library
of_mdio: fix phy interrupt passing
net: ethernet: update dependency and help text of mvneta
NET: fec: only enable napi if we are successful
af_packet: remove a stray tab in packet_set_ring()
net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
ipv4: fix counter in_slow_tot
irtty-sir.c: Do not set_termios() on irtty_close()
bonding: 802.3ad: make aggregator_identifier bond-private
usbnet: remove generic hard_header_len check
gre: add link local route when local addr is any
batman-adv: fix potential kernel paging error for unicast transmissions
batman-adv: avoid double free when orig_node initialization fails
batman-adv: free skb on TVLV parsing success
batman-adv: fix TT CRC computation by ensuring byte order
batman-adv: fix potential orig_node reference leak
batman-adv: avoid potential race condition when adding a new neighbour
batman-adv: properly check pskb_may_pull return value
batman-adv: release vlan object after checking the CRC
batman-adv: fix TT-TVLV parsing on OGM reception
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.
Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:
- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above
This fixes the issue:
net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI
to the correct:
net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 8fdade4 ("net: of_mdio: parse "max-speed" property to set PHY
supported features") introduced a typo in of_set_phy_supported for the
first assignment of phydev->supported which will not effectively limit
the PHY device supported features bits if the PHY driver contains
"higher" features (e.g: max-speed = <100> and PHY driver has
PHY_GBIT_FEATURES set).
Fix this by making sure that the very first thing is to reset to sane
defaults (PHY_BASIC_FEATURES) and then progressively add speed features
as we parse them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This reverts commit 105353145eafb3ea919f5cdeb652a9d8f270228e.
Stephen Chivers reported this is broken as we will get a match
entry '.type = "serial"' instead of the '.compatible = "ns16550"'
in the following scenario:
serial0: serial@4500 {
compatible = "fsl,ns16550", "ns16550";
}
struct of_device_id of_platform_serial_table[] = {
{ .compatible = "ns8250", .data = (void *)PORT_8250, },
{ .compatible = "ns16450", .data = (void *)PORT_16450, },
{ .compatible = "ns16550a", .data = (void *)PORT_16550A, },
{ .compatible = "ns16550", .data = (void *)PORT_16550, },
{ .compatible = "ns16750", .data = (void *)PORT_16750, },
{ .compatible = "ns16850", .data = (void *)PORT_16850, },
...
{ .type = "serial", .data = (void *)PORT_UNKNOWN, },
{ /* end of list */ },
};
So just revert this patch, we will use another implementation to find
the best compatible match in a follow-on patch.
Reported-by: Stephen N Chivers <schivers@csc.com.au>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On IBM pseries systems the device_type device-tree property of a PCIe
bridge contains the string "pciex". The of_bus_pci_match() function was
looking only for "pci" on this property, so in such cases the bus
matching code was falling back to the default bus, causing problems on
functions that should be using "assigned-addresses" for region address
translation. This patch fixes the problem by also looking for "pciex" on
the PCI bus match function.
v2: added comment
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
10G PHYs don't currently support running the state machine, which
is implicitly setup via of_phy_connect(). Therefore, it is necessary
to implement an OF version of phy_attach(), which does everything
except start the state machine.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
