summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/iwlwifi/iwl-mac80211.c
Commit message (Collapse)AuthorAgeFilesLines
* iwlwifi: move all ucode routines to iwl-ucode.cDon Fry2012-02-021-1/+1
| | | | | | | | | The routines dealing with the ucode are spread through several files. Move them all to the same file and create a iwl-ucode.h file with the ucode file definitions. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: stop_hw replace enable_rfkill_intEmmanuel Grumbach2012-02-021-3/+4
| | | | | | | | | | This trans_ops->stop_hw leaves the RFKILL interrupt enabled, we can call that one instead of enable_rfkill_int. By that, we reduce the numbers of acceesses to the NIC from the upper layers. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: kill bus_get_hw_idEmmanuel Grumbach2012-02-021-1/+1
| | | | | | | Get this information from the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: give trans to all the read / write functionsEmmanuel Grumbach2012-02-021-13/+14
| | | | | | | | | From now on, the transport layer in charge of providing access to the device. So change all the driver to give a pointer to the transport to all the low level functions that actually access the device. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: update CopyrightWey-Yi Guy2012-01-061-1/+1
| | | | | | Update Copyright to 2012 Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: set hw_version in wiphyWey-Yi Guy2011-12-191-0/+2
| | | | | | Set the hw_version in wiphy structure Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlagn: finer-grained HT disableJohannes Berg2011-12-191-0/+4
| | | | | | | | | | | | At least while debugging, a lot of people use 11n_disable=1 to disable HT completely. To be able to figure out what parts of HT cause the problems we see, make the parameter a bitmap, allowing to disable all of HT and aggregation (TX/RX) separately. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: remove most of the iwl_priv references from iwl-ucode.cDon Fry2011-12-161-2/+3
| | | | | | | | Remove all but the last few references to iwl_priv from the lower level iwl-ucode.c, with resulting code changes. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: create iwl_mac80211 unregister routineDon Fry2011-12-161-0/+9
| | | | | | | | The mac80211 setup_register operations are collected in one routine, but the cleanup routines are not. Create a routine for this. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: tid_data logic move to upper layer - tx AGG setupEmmanuel Grumbach2011-12-161-49/+1
| | | | | | | | | The tid_data is not related to the transport layer, so move the logic that depends on it to the upper layer. This patch deals with tx AGG setup. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: move iwl_cfg from iwl_priv to iwl_sharedDon Fry2011-12-161-11/+11
| | | | | | | | Move the configuration pointer from the upper level iwl_priv to the lower level iwl_shared structure, with associated code fixes. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* Merge branch 'master' of ↵John W. Linville2011-12-141-0/+6
| | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/iwlwifi/iwl-agn.c
* iwlwifi: move device_pointers from iwl_priv to iwl_sharedDon Fry2011-12-081-1/+1
| | | | | | | Move the low level ucode device_pointers structure to iwl_shared. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlagn: remove MACDUMP debugJohannes Berg2011-12-021-4/+0
| | | | | | | | | This is only used for TX debugging where there already is more debugging and tracing is more useful anyway, so remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlagn: fix HW crypto for TX-only keysJohannes Berg2011-12-021-0/+11
| | | | | | | | | | | | | | | Group keys in IBSS or AP mode are not programmed into the device since we give the key to it with every TX packet. However, we do need mac80211 to create the MMIC & PN in all cases. Move the code around to set the key flags all the time. We set them even when the key is removed again but that is obviously harmless. Cc: stable@vger.kernel.org Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlwifi: do not re-configure HT40 after associatedWey-Yi Guy2011-12-021-15/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ht40 setting should not change after association unless channel switch This fix a problem we are seeing which cause uCode assert because driver sending invalid information and make uCode confuse Here is the firmware assert message: kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000. kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301 kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump: kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6 kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1 kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2 kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1 kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2 kernel: iwlagn 0000:03:00.0: 0x01008035 | data1 kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2 kernel: iwlagn 0000:03:00.0: 0x000005A7 | line kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1 kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2 kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3 kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version kernel: iwlagn 0000:03:00.0: 0x00480303 | board version kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd kernel: iwlagn 0000:03:00.0: CSR values: kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG) kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303 kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40 kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030 kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5 kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0 kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001 kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001 kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044 kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078 kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2 kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200 kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010 kernel: iwlagn 0000:03:00.0: FH register values: kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060 kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries kernel: ------------[ cut here ]------------ WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407() kernel: Hardware name: 4290W4H kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2 kernel: Call Trace: kernel: [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87 kernel: [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407 kernel: [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32 kernel: [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87 kernel: [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3 kernel: [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff8104ba97>] ? kthread+0x7a/0x82 kernel: [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10 kernel: [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11 kernel: [<ffffffff813d21b0>] ? gs_change+0xb/0xb Cc: <stable@kernel.org> 3.1+ Reported-by: Udo Steinberg <udo@hypervisor.org> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
* iwlagn: convert remain-on-channel duration to TUJohannes Berg2011-11-111-1/+2
| | | | | | | | The device expects TU but we get ms, so convert. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: Move the core suspend function to iwl-agn-libWey-Yi Guy2011-11-111-345/+2
| | | | | | | | The core suspend function is part of agn, iwl_mac80211 should only handle mac80211 I/F operations. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: move station functions to mac80211Wey-Yi Guy2011-11-111-0/+71
| | | | | | | The station related mac80211 callback functions should belong to _mac80211 Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: move hw_scan into _mac80211 fileWey-Yi Guy2011-11-111-0/+46
| | | | | | | iwlagn_mac_hw_scan should belong to _mac80211 callback. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: move more mac80211 callback functionWey-Yi Guy2011-11-111-0/+308
| | | | | | | Move more mac80211 related functions to _mac80211 file Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlagn: explicitly program P2P QoS parametersJohannes Berg2011-11-111-0/+28
| | | | | | | | | | | | | | | | | | | | | | | In P2P device mode, the device needs to have valid QoS parameters. We currently have those because we program parameters from any virtual interface into all contexts, but not only do we want to get rid of this -- it is also unpredictable since on the BSS context we might have any parameters, and there it might even be programmed for HT. Explicitly program default QoS parameters into the PAN context for P2P (the defaults are 11g but with QoS disabled) to make device behaviour predictable. This also helps when in a follow-up patch we will use TX QoS parameters from mac80211 only for the context they were meant for -- without this first that would completely break P2P device discovery. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: move all mac80211 related functions to one placeWey-Yi Guy2011-11-111-0/+1521
There are many mac80211 callback functions in the driver, as current implementation, those functions are scatter everywhere which is very difficult to find and maintain, move all the mac80211 callback functions into single file. There should be no functional changes Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
OpenPOWER on IntegriCloud