summaryrefslogtreecommitdiffstats
path: root/drivers/net/tg3.c
Commit message (Collapse)AuthorAgeFilesLines
* [TG3]: Fix build warning on sparc32.David S. Miller2008-03-201-3/+3
| | | | | | | | | | | | Sparc MAC address support should be protected consistently with CONFIG_SPARC, but there was a stray CONFIG_SPARC64 case. Bump driver version and release date. Reported by Andrew Morton. Signed-off-by: David S. Miller <davem@davemloft.net>
* tg3: ethtool phys_id defaultStephen Hemminger2008-02-231-1/+1
| | | | | | | | | | | | | When asked to blink LEDs the tg3 driver behaves when using: ethtool -p ethX The default value for data is zero, and other drivers interpret this as blink forever (or at least a really long time). The tg3 driver interprets this as blink once. All drivers should have the same behaviour. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* NULL noise in drivers/netAl Viro2008-01-281-1/+1
| | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version to 3.87Matt Carlson2008-01-281-2/+2
| | | | | | | | This patch updates the version number to 3.87. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix supporting flowctrl codeMatt Carlson2008-01-281-43/+64
| | | | | | | | | | | | | | | | | | This patch does three things. It modifies tg3_setup_flow_control() to use the administrator requested flow control settings if autonegotiation is turned off. It slightly modifies the tg3_setup_fiber_mii_phy() function to account for this new use case. And finally, it does the same for tg3_setup_copper_phy(). The copper modifications are more than a small multi-line change. The new code makes an attempt to avoid a link renegotiation if the link is active at half duplex and the only difference between the current advertised settings and requested advertised settings is the flow control advertisements. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Correct sw autoneg flow control advertisementsMatt Carlson2008-01-281-13/+25
| | | | | | | | | | | | This patch modifies the software autoneg code to use the administrator specified flow control parameters. Since the autonegotiation code uses alternative flow control enumerations, the 1000-BaseX utility functions are used and code was added to convert the definitions to and from the alternate enumerations. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Correct 5704S flowctrl advertisementsMatt Carlson2008-01-281-11/+15
| | | | | | | | | | | | This patch modifies the 5704S hardware autoneg code to use the administrator specified flow control parameters. Since the 5704S uses device specific flow control enumerations, the 1000-BaseX utility functions are used and code was added to convert the definitions to and from the proprietary enumerations. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Replace some magic 5704S constantsMatt Carlson2008-01-281-11/+12
| | | | | | | | | | This patch replaces magic values with preprocessor definitions for the sg_dig_ctrl and sg_dig_status registers. This is preparatory work for the next patch. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 1000T & 1000X flowctl adv helpersMatt Carlson2008-01-281-14/+48
| | | | | | | | | | | | | This patch adds two functions designed to convert abstract TX & RX flow control parameters to 1000-BaseT and 1000-BaseX autonegotiation advertisements. Code that uses standard definitions which statically advertises TX & RX flow control has been replaced with code that configures the advertisements based on administrator dictated preferences. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 1000T & 1000X flowctrl resolversMatt Carlson2008-01-281-36/+50
| | | | | | | | | | | This patch adds two new utility functions to resolve flow control. One function resolves flow control based on 1000-BaseT register definitions. The other resolves flow control based on 1000-Base X register definitions. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Separate requested and actual flow control parametersMatt Carlson2008-01-281-33/+36
| | | | | | | | | This patch removes the TX and RX flow control flags from tg3_flags and adds two new flow control variables, flowctrl and active_flowctrl. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Use print_macJoe Perches2008-01-281-7/+6
| | | | | Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Endianness bugfix.Al Viro2007-12-191-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tg3_nvram_write_block_unbuffered() is reading data from nvram into allocated buffer before overwriting a part of it with user-supplied data. Then it feeds the entire page back to nvram. It should be storing the words it had read as little-endian, not as host-endian. Note that tg3_set_eeprom() does exactly that for padding the same data to full words before it gets passed down to tg3_nvram_write_block() and then to tg3_nvram_write_block_unbuffered(). Moreover, when we get to sending the entire thing back to nvram, we go through it word-by-word, doing essentially writel(swab32(le32_to_cpu(word)), ...) so if we want them to reach the card in host-independent endianness, we'd better really have all that buffer filled with fixed-endian. For user-supplied part we obviously do have that (it's an array of octets memcpy'd in), ditto for padding of user-supplied part to word boundaries (taken care of in tg3_set_eeprom()). The rest of the buffer gets filled by tg3_nvram_write_block_unbuffered() and it would damn better be consistent with that (and with tg3_get_eeprom(), while we are at it - there we also convert the words read from nvram to little-endian before returning the buffer to user). The bug should get triggered on big-endian boxen when set_eeprom is done for less than entire page. Then the words that should've been unaffected at all will actually get byteswapped in place in nvram. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Endianness annotations.Al Viro2007-12-191-43/+54
| | | | | | | | | | | | | Fixed misannotations, introduced a new helper - tg3_nvram_read_le(). It gets __le32 * instead of u32 * and puts there the value converted to little-endian. A lot of callers of tg3_nvram_read() were doing that; converted them to tg3_nvram_read_le(). At that point the driver is practically endian-clean; the only remaining place is an actual bug, AFAICS; will be dealt with in the next patch. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version to 3.86Matt Carlson2007-11-121-2/+2
| | | | | | | | This patch updates the version number to 3.86 Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: MII => TPMatt Carlson2007-11-121-1/+1
| | | | | | | | | This patch changes the PHY type reported through ethtool for copper devices from MII to TP. The latter is more accurate. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add A1 revsMatt Carlson2007-11-121-12/+18
| | | | | | | | | | This patch adds the A1 revision of 5784, 5764, and 5761, and applies all previous bugfixes. In places where the list of devices gets too long, the patch uses a new TG3_FLG3_5761_5784_AX_FIXES flag instead. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Increase the PCI MRRSMatt Carlson2007-11-121-1/+7
| | | | | | | | | | | Previous devices hardcoded the PCI Maximum Read Request Size to 4K. To better comply with the PCI spec, the hardware now defaults the MRRS to 512 bytes. This will yield poor driver performance if left untouched. This patch increases the MRRS to 4K on driver initialization. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Prescaler fixMatt Carlson2007-11-121-0/+16
| | | | | | | | | | | Internal hardware timers become inaccurate after link events. Clock frequency switches performed by the CPMU fail to adjust timer prescalers. The fix is to detect core clock frequency changes during link events and adjust the timer prescalers accordingly. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Limit 5784 / 5764 to MAC LED modeMatt Carlson2007-11-121-0/+3
| | | | | | | | | Most 5784 / 5764 LED modes do not work as expected because of a hardware bug. This patch forces the LED mode to be in MAC LED mode. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Disable GPHY autopowerdownMatt Carlson2007-11-121-0/+6
| | | | | | | | | | New CPMU devices contend with the GPHY for power management. The GPHY autopowerdown feature is enabled by default in the PHY and thus needs to be disabled after every PHY reset. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: CPMU adjustments for loopback testsMatt Carlson2007-11-121-5/+7
| | | | | | | | | | This patch adds the LINK_SPEED mode to the list of CPMU modes that can cause the loopback tests to fail. These bugs are planned to be fixed in future revisions of the chip, so the patch qualifies the fixes as such. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix nvram selftest failuresMatt Carlson2007-11-121-6/+30
| | | | | | | | | | | | | Newer devices contain bootcode in the chip's private ROM area. This bootcode is called selfboot. Selfboot can be patched in the device's NVRAM and the patches can have several formats. In one particular format, the checksum calculation needs to be slightly modified. This patch adjusts the NVRAM test code for that case, and add support for the missing formats. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: 5784 / 5764 DMA engine lockup fixMatt Carlson2007-11-121-0/+15
| | | | | | | | | | 5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The fix is to run the MAC clock at faster speeds. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: APE flag fixMatt Carlson2007-11-121-1/+1
| | | | | | | | | This patch corrects a bug where the ENABLE_APE flag was tested against the wrong flag variable. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: 5784 / 5764 GPHY power down fixMatt Carlson2007-11-121-2/+24
| | | | | | | | | | | | | | 5784 and 5764 devices fail to link / pass traffic after one load / unload cycle. This happens because of a hardware bug in the new CPMU. During normal operation, the MAC depends on the PHY clock being available. When the PHY is powered down, the clock the MAC depends on is disabled. The fix is to switch the MAC clock to an alternate source before powering down the PHY, and to restore the MAC clock to the PHY source upon device resume. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix 5761 PXEboot crashMatt Carlson2007-11-121-23/+23
| | | | | | | | | | | | | | | | When 5761 devices boot the machine using PXEboot, PXE leaves the device active when it terminates. The tg3 driver has code to detect this condition and resets the device during initialization. On 5761 devices, device resets involve sending a driver state update message to the APE on the 5761. However, during this initialization stage, communications to the APE registers have not yet been set up. The driver then dereferences a NULL pointer and crashes the machine. The fix is to move the APE register access setup earlier in the initialization code to cover this condition. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* PCI: Add quirk for devices which disable MSI when INTX_DISABLE is set.David Miller2007-11-051-9/+0
| | | | | | | | | | | | | | | | | | A reasonably common problem with some devices is that they will disable MSI generation when the INTX_DISABLE bit is set in the PCI_COMMAND register. Quirk this explicitly, guarding the pci_intx() calls in msi.c with this quirk indication. The first entries for this quirk are for 5714 and 5780 Tigon3 chips, and thus we can remove the workaround code from the tg3.c driver. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Michael Chan <mchan@broadcom.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [TG3]: Update version to 3.85Matt Carlson2007-10-221-2/+2
| | | | | | | | This patch updates the version number to 3.85. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: PCI command adjustmentMatt Carlson2007-10-221-5/+2
| | | | | | | | | | | This patch changes the way the driver works with the PCI command register. It adjusts the access size from dwords to words. This patch is done both as a PCI configuration space cleanup and as preparatory work for PCI error recovery. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add management FW version to ethtool reportMatt Carlson2007-10-221-13/+70
| | | | | | | | | This patch appends the management firmware version to the bootcode firmware string reported through ethtool. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5723 supportMatt Carlson2007-10-221-0/+1
| | | | | | | | This patch adds support for upcoming 5723 devices. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵Linus Torvalds2007-10-151-2/+8
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits) [IPV6]: Consolidate the ip6_pol_route_(input|output) pair [TCP]: Make snd_cwnd_cnt 32-bit [TCP]: Update the /proc/net/tcp documentation [NETNS]: Don't panic on creating the namespace's loopback [NEIGH]: Ensure that pneigh_lookup is protected with RTNL [INET]: kmalloc+memset -> kzalloc in frag_alloc_queue [ISDN]: Fix compile with CONFIG_ISDN_X25 disabled. [IPV6]: Replace sk_buff ** with sk_buff * in input handlers [SELINUX]: Update for netfilter ->hook() arg changes. [INET]: Consolidate the xxx_put [INET]: Small cleanup for xxx_put after evictor consolidation [INET]: Consolidate the xxx_evictor [INET]: Consolidate the xxx_frag_destroy [INET]: Consolidate xxx_the secret_rebuild [INET]: Consolidate the xxx_frag_kill [INET]: Collect common frag sysctl variables together [INET]: Collect frag queues management objects together [INET]: Move common fields from frag_queues in one place. [TG3]: Fix performance regression on 5705. [ISDN]: Remove local copy of device name to make sure renames work. ...
| * [TG3]: Fix performance regression on 5705.Michael Chan2007-10-151-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A performance regression was introduced by the following commit: commit ee6a99b539a50b4e9398938a0a6d37f8bf911550 Author: Michael Chan <mchan@broadcom.com> Date: Wed Jul 18 21:49:10 2007 -0700 [TG3]: Fix msi issue with kexec/kdump. In making that change, the PCI latency timer and cache line size registers were not restored after chip reset. On the 5705, the latency timer gets reset to 0 during chip reset and this causes very poor performance. Update version to 3.84. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | netdev: convert non-obvious instances to use ARRAY_SIZE()Alejandro Martinez Ruiz2007-10-151-1/+1
|/ | | | | | | | This will convert remaining non-obvious or naive calculations of array sizes to use ARRAY_SIZE() macro. Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [TG3]: Refine napi poll loop.Michael Chan2007-10-121-10/+14
| | | | | | | | | | | | | | Need to read and store sblk->status_tag before checking for more work. The status tag is later written back to the hardware when enabling interrupts to acknowledge how much work has been processed. If the order is reversed, we can end up acknowledging work we haven't processed. When we detect tx error, it is more correct to return the rx work_done so far instead of 0. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix APE induced regressionMatt Carlson2007-10-111-3/+4
| | | | | | | | This patch fixes a bug caused by the recent APE support added for 5761 devices. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [NET]: Fix NAPI completion handling in some drivers.David S. Miller2007-10-111-18/+37
| | | | | | | | | | | | | | | | | | | | | In order for the list handling in net_rx_action() to be correct, drivers must follow certain rules as stated by this comment in net_rx_action(): /* Drivers must not modify the NAPI state if they * consume the entire weight. In such cases this code * still "owns" the NAPI instance and therefore can * move the instance around on the list at-will. */ A few drivers do not do this because they mix the budget checks with reading hardware state, resulting in crashes like the one reported by takano@axe-inc.co.jp. BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen Hemminger. Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version to 3.83Matt Carlson2007-10-101-2/+2
| | | | | | | | Update to version 3.83. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: WOL defaultsMatt Carlson2007-10-101-6/+9
| | | | | | | | | This patch enables WOL by default if out-of-box WOL is enabled in the NVRAM. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5761 supportMatt Carlson2007-10-101-13/+73
| | | | | | | | | This patch adds rest of the miscellaneous code required to support the 5761. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5761 APE supportMatt Carlson2007-10-101-4/+228
| | | | | | | | | | This patch adds support for the new APE block, present in 5761 chips. APE stands for Application Processing Engine. The primary function of the APE is to process manageability traffic, such as ASF. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add new 5761 NVRAM decode routinesMatt Carlson2007-10-101-0/+79
| | | | | | | | | This patch adds a new 5761-specific NVRAM strapping decode routine. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix ethtool autonegotiate flags.Andy Gospodarek2007-10-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I recently noticed that when calling: # ethtool -s eth0 autoneg on on a 5722 (though I'm sure it's not specific to that card) that subsequent checks of the cards status looked like this: # ethtool eth0 Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: No <---- This seems odd?!? Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes I noticed that the following commit: commit 3600d918d870456ea8e7bb9d47f327de5c20f3d6 Author: Michael Chan <mchan@broadcom.com> Date: Thu Dec 7 00:21:48 2006 -0800 [TG3]: Allow partial speed advertisement. Honor the advertisement bitmask from ethtool. We used to always advertise the full capability when autoneg was set to on. changed things around so that ethtool speed settings were strictly followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg in the advertising field (and maybe it shouldn't have to). I'd vote that it should be fixed there, but it should also be added here just in case someone using ethtool ioctls in their own application gets what they want. Adding that flag in tg3_set_settings seemed like the most logical place since the driver works fine on boot. This is just an issue when re-enabling autonegotiation, so we should probably nip it there. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version to 3.82.Michael Chan2007-10-101-2/+2
| | | | | Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5784 and 5764 support.Matt Carlson2007-10-101-11/+42
| | | | | | | | This patch adds the support for 5784 and 5764 devices. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: ASIC decoding and basic CPMU support.Matt Carlson2007-10-101-5/+16
| | | | | | | | | | | | | Newer products change the way the ASIC revision is obtained. This patch implements how the driver will extract the revision number. This patch also adds preliminary CPMU support. CPMU stands for Central Power Management Unit. The CPMU's role is to put the chip into lower power states when the operating conditions allow it. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Walk PCI capability lists.Matt Carlson2007-10-101-13/+35
| | | | | | | | | | | Newer tg3 devices shuffle around the registers in PCI configuration space. This patch changes the way the driver accesses the PCI capabilities registers. Hardcoded register locations are replaced with offsets from pci_find_capability() return values. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [netdrvr] Stop using legacy hooks ->self_test_count, ->get_stats_countJeff Garzik2007-10-101-9/+10
| | | | | | | These have been superceded by the new ->get_sset_count() hook. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [ETHTOOL] Provide default behaviors for a few ethtool sub-ioctlsJeff Garzik2007-10-101-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | For the operations get-tx-csum get-sg get-tso get-ufo the default ethtool_op_xxx behavior is fine for all drivers, so we permit op==NULL to imply the default behavior. This provides a more uniform behavior across all drivers, eliminating ethtool(8) "ioctl not supported" errors on older drivers that had not been updated for the latest sub-ioctls. The ethtool_op_xxx() functions are left exported, in case anyone wishes to call them directly from a driver-private implementation -- a not-uncommon case. Should an ethtool_op_xxx() helper remain unused for a while, except by net/core/ethtool.c, we can un-export it at a later date. [ Resolved conflicts with set/get value ethtool patch... -DaveM ] Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud