summaryrefslogtreecommitdiffstats
path: root/drivers/net/sky2.c
Commit message (Collapse)AuthorAgeFilesLines
* sky2: program proper register for fiber PHYStephen Hemminger2007-05-301-1/+1
| | | | | | | | Driver was reading value from one register, setting bit and then writing the wrong register. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: checksum offload plus vlan bugStephen Hemminger2007-05-301-1/+1
| | | | | | | | Driver was not correctly setting up transmit descriptor when doing VLAN tag insertion with checksum offload. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: dont set bogus bit in PHY registerStephen Hemminger2007-05-301-1/+1
| | | | | | | | | | This code inherited from the sk98lin driver is incorrect on the Yukon2. The GPHY_CTRL register values are specific to the internal PHY of the chip and the values used were leftovers. Driver was setting bit 13 which is now the INT polarity for the PHY! Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: memory barriers changeStephen Hemminger2007-05-171-4/+11
| | | | | | | | | Do some memory barrier changes for safety/perfomance: Don't need read after update to index, mmiowb() followed by read at end of irq is sufficient. Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: remove dual port workaroundStephen Hemminger2007-05-171-7/+0
| | | | | | | | | | This workaround was added to deal with NAPI core and how it affected dual port shared polling. It turned out not to be necessary. Stopping device 0 only doesn't stop NAPI from working completely after that. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: MIB counter overflow handlingStephen Hemminger2007-05-171-0/+6
| | | | | | | | Make sure that if we ever get a MIB counter overflow interrupt (normally masked off), that the IRQ is cleared. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: keep track of receive alloc failuresStephen Hemminger2007-05-171-1/+3
| | | | | | | | When driver can't allocate receive buffer it drops incoming packet. Keep a counter. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: PHY register settingsStephen Hemminger2007-05-171-1/+6
| | | | | | | | | | | Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3) driver. The PHY register settings are mostly black magic, even with access to the documentation it isn't clear what the right values are. The changes are mostly comments, the code change only affects the Yukon FE (100 mbit only) version. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: remove Gigabyte 88e8056 restrictionStephen Hemminger2007-05-171-30/+0
| | | | | | | | | The problems with Gigabyte motherboards are system configuration dependent. Since it works fine for some users, it doesn't make sense to deprive them. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: only disable 88e8056 on some boardsStephen Hemminger2007-05-111-11/+30
| | | | | | | | | Use DMI to add a blacklist of broken boards (so far only one). Hopefully, the problems will be solved later, and the the whole blacklist can disappear. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: 88e8071 support not readyStephen Hemminger2007-05-111-1/+1
| | | | | | | | | | The driver is not ready to support 88e8071 chip. If this chip is present, system will hang on boot. So remove it from PCI device id's for now. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: fix oops on shutdownStephen Hemminger2007-05-111-0/+10
| | | | | | | | | If the device is fails during module startup for some reason like unsupported chip version then the driver would crash dereferencing a null pointer, on shutdown or suspend/resume. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: re-enable 88E8056 for most motherboardsStephen Hemminger2007-05-081-4/+13
| | | | | | | | This fixes the regression in 2.6.21 for users with 88e8056 on motherboard. Allow all but the Gigabyte motherboard has some unresolved bus problems. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [SK_BUFF]: Introduce skb_copy_from_linear_data{_offset}Arnaldo Carvalho de Melo2007-04-251-1/+1
| | | | | | | To clearly state the intent of copying from linear sk_buffs, _offset being a overly long variant but interesting for the sake of saving some bytes. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* [TCP]: Introduce tcp_hdrlen() and tcp_optlen()Arnaldo Carvalho de Melo2007-04-251-1/+1
| | | | | | | | | | | | The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to avoid the longer, open coded equivalent. Ditched a no-op in bnx2 in the process. I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()... Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [SK_BUFF]: Introduce skb_transport_offset()Arnaldo Carvalho de Melo2007-04-251-1/+1
| | | | | | | For the quite common 'skb->h.raw - skb->data' sequence. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [SK_BUFF]: Introduce ip_hdr(), remove skb->nh.iphArnaldo Carvalho de Melo2007-04-251-1/+1
| | | | | Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [IP]: Introduce ip_hdrlen()Arnaldo Carvalho de Melo2007-04-251-1/+2
| | | | | | | | | | | | | | | | For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open coded skb->nh.iph uses, now to go after the rest... Just out of curiosity, here are the idioms found to get the same result: skb->nh.iph->ihl << 2 skb->nh.iph->ihl<<2 skb->nh.iph->ihl * 4 skb->nh.iph->ihl*4 (skb->nh.iph)->ihl * sizeof(u32) Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: version 1.14Stephen Hemminger2007-04-191-1/+1
| | | | | Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: no jumbo on Yukon FEStephen Hemminger2007-04-191-0/+3
| | | | | | | The Yukon FE (100mbit only) chips do not support large packets. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: EC-U performance and jumbo supportStephen Hemminger2007-04-191-25/+60
| | | | | | | | | | | | | The Yukon EC Ultra chips have transmit settings for store and forward and PCI buffering. By setting these appropriately, normal performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo). It is also possible to do Jumbo mode, but it means turning off TSO and checksum offload so the performance gets worse. There isn't enough buffering for checksum offload to work. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: disable ASF on all chip typesStephen Hemminger2007-04-191-10/+8
| | | | | | | | Need to make sure and disable ASF on all chip types. Otherwise, there may be random reboots. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: handle descriptor errorsStephen Hemminger2007-04-191-31/+36
| | | | | | | | There should never be descriptor error unless hardware or driver is buggy. But if an error occurs, print useful information, clear irq, and recover. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: disable support for 88E8056Stephen Hemminger2007-04-191-0/+3
| | | | | | | | | | | | This device is having all sorts of problems that lead to data corruption and system instability. It gets receive status and data out of order, it generates descriptor and TSO errors, etc. Until the problems are resolved, it should not be used by anyone who cares about there system. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: phy workarounds for Yukon EC-U A1Stephen Hemminger2007-04-111-3/+3
| | | | | | | | | The workaround Yukon EC-U wasn't comparing with correct version and wasn't doing correct setup. Without it, 88e8056 throws all sorts of errors. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: turn on clocks when doing resumeStephen Hemminger2007-04-111-0/+5
| | | | | | | | | Some of these chips are disabled until clock is enabled. This fixes: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107 Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: turn carrier off when downStephen Hemminger2007-04-111-0/+1
| | | | | | | Driver needs to turn off carrier when down. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: turn off Rx checksum on bad hardwareStephen Hemminger2007-03-091-3/+21
| | | | | | | | | | On Yukon FE, occasional hardware receive checksum errors are seen. An early indication of the problem is single bit differences in the two checksum engines. Use this as a detection mechanism to turn off Rx checksumming. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [VLAN]: Avoid a 4-order allocation.Dan Aloni2007-03-021-2/+1
| | | | | | | | | | | | | | This patch splits the vlan_group struct into a multi-allocated struct. On x86_64, the size of the original struct is a little more than 32KB, causing a 4-order allocation, which is prune to problems caused by buddy-system external fragmentation conditions. I couldn't just use vmalloc() because vfree() cannot be called in the softirq context of the RCU callback. Signed-off-by: Dan Aloni <da-x@monatomic.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: v1.13Stephen Hemminger2007-02-171-1/+1
| | | | | | | New version. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: receive error handling improvementsStephen Hemminger2007-02-171-8/+1
| | | | | | | | | Don't drop oversize frame it might be a VLAN (untagged). Use different counter for fifo overrun vs fifo error. Print error on fifo overrrun. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: transmit timeoutStephen Hemminger2007-02-171-16/+49
| | | | | | | | | The transmit timeout code could hang, and it would not clear out problems if the hardware was stuck. Change the code to effectively do a device down/up similar to the suspend/resume code. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: flow control negotiation for Yukon-FEStephen Hemminger2007-02-171-11/+31
| | | | | | | | | | | The Yukon-FE chip doesn't do gigabit and has a differen PHY internally. On this chip, phy status register doesn't properly reflect the result of flow control negotiation. To workaround the problem and avoid having to have so much chip dependent code; compute the result of flow control by looking at the local and remote advertised bits. Signed-off-by: Stephen Hemmminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: no need to reset pause bits on shutdownStephen Hemminger2007-02-171-7/+0
| | | | | | | | | Resetting the pause bits on shutdown is not necessary. The code was inherited from the vendor driver, and it is currently #ifdef'd out there as well. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: version 1.12Stephen Hemminger2007-02-071-1/+1
| | | | | | | Updated version for WOL and new id's Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: add new chip idsStephen Hemminger2007-02-071-0/+4
| | | | | | | More new chip id's from vendor driver version 10.0.4.3 Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: Yukon Extreme supportStephen Hemminger2007-02-071-12/+37
| | | | | | | | | | This is basic support for the new Yukon Extreme chip, extracted from the new vendor driver 10.0.4.3. Since this is untested hardware, it has a big fat warning for now. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: safer transmit timeoutStephen Hemminger2007-02-071-26/+15
| | | | | | | | Rather than trying to be "smart" about possible transmit timeout causes. Just clear all pending frames and reset the PHY. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: TSO support for EC_UStephen Hemminger2007-02-071-4/+3
| | | | | | | | The Yukon EC_U chipset apparently supports TSO but only for non-Jumbo frame sizes because it lacks a Ram buffer. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: use dev_err for error reportsStephen Hemminger2007-02-071-44/+31
| | | | | | | | | Use the standard dev_xxx functions instead of printk directly for error reports. Fix a bug where the initialization would return 0 if allocation of network device failed. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: add Wake On Lan supportStephen Hemminger2007-02-071-27/+181
| | | | | | | | Adds basic magic packet wake on lan support to the sky2 driver. Note: initial WOL value is based on BIOS settings. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: handle network device allocation failureshemminger@linux-foundation.org2007-02-051-6/+14
| | | | | | | | If alloc_etherdev() failed, then sky2_init_netdev will return NULL, and sky2_probe would end up returning 0 instead of -ENOMEM. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: software rx/tx statsshemminger@linux-foundation.org2007-02-051-16/+5
| | | | | | | | | | Maintain packet statistics in software rather than hardware. This is slightly slower, but allows easier debugging of problems where packets are still being received by PHY but not being handled by hardware. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: version 1.11.1shemminger@linux-foundation.org2007-02-051-1/+1
| | | | | | | Version update to 1.11.1. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: better power state managementStephen Hemminger2007-02-051-83/+57
| | | | | | | | Improve power management and error handling by using pci_set_power_state(), instead of driver doing PCI PM register changes in the driver. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] sky2: revert IRQ dance on suspend/resumeStephen Hemminger2007-01-291-25/+0
| | | | | | | | | | | | | Let's just backout the IRQ hack, and for those crap machines (like some Sony VAIO's) can just disable MSI with the module parameter. This reverts 44ade178249fe53d055fd92113eaa271e06acddd. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Frédéric Riss <frederic.riss@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] email change for shemminger@osdl.orgStephen Hemminger2007-01-231-1/+1
| | | | | | | | | Change my email address to reflect OSDL merger. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> [ The irony. Somebody still has his sign-off message hardcoded in a script or his brainstem ;^] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sky2: phy power down needs PCI config write enabledStephen Hemminger2006-12-261-1/+2
| | | | | | | | | In order to change PCI registers (via the iomap'd window), it needs to be enabled; this wasn't being done in sky2_phy_power the function that turns on/off power to the PHY. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: power management/MSI workaroundStephen Hemminger2006-12-261-0/+25
| | | | | | | | | | | | | | MSI doesn't work properly on resume on many platforms because the BIOS goes and changes it back to INTx mode after the sky2 driver has restored in resume. It is really a bug in the base power management resume code, and this workaround is temporary until the change to PM code works it's way through the release process. The PM fix is non-trivial since it needs to change when non-boot CPU's are enabled. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sky2: dual port NAPI problemStephen Hemminger2006-12-261-0/+7
| | | | | | | | | Shutting down port 0 disables the NAPI poll used by both ports. The long term fix will be to separate NAPI object from net device until then just reenable if needed. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
OpenPOWER on IntegriCloud