summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/mdio_bus.c
Commit message (Collapse)AuthorAgeFilesLines
* net: phy: Maintain MDIO device and bus statisticsFlorian Fainelli2020-01-171-2/+249
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We maintain global statistics for an entire MDIO bus, as well as broken down, per MDIO bus address statistics. Given that it is possible for MDIO devices such as switches to access MDIO bus addresses for which there is not a mdio_device instance created (therefore not a a corresponding device directory in sysfs either), we also maintain per-address statistics under the statistics folder. The layout looks like this: /sys/class/mdio_bus/../statistics/ transfers errrors writes reads transfers_<addr> errors_<addr> writes_<addr> reads_<addr> When a mdio_device instance is registered, a statistics/ folder is created with the tranfers, errors, writes and reads attributes which point to the appropriate MDIO bus statistics structure. Statistics are 64-bit unsigned quantities and maintained through the u64_stats_sync.h helper functions. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Simplify reset handling and extend to non-DT systemsGeert Uytterhoeven2020-01-141-11/+5
| | | | | | | | | | | | Convert mdiobus_register_reset() from open-coded DT-only optional reset handling to reset_control_get_optional_exclusive(). This not only simplifies the code, but also adds support for lookup-based resets on non-DT systems. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: don't use managed reset-controllerDavid Bauer2019-11-251-2/+4
| | | | | | | | | | | | | | | | Geert Uytterhoeven reported that using devm_reset_controller_get leads to a WARNING when probing a reset-controlled PHY. This is because the device devm_reset_controller_get gets supplied is not actually the one being probed. Acquire an unmanaged reset-control as well as free the reset_control on unregister to fix this. Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Fix init if CONFIG_RESET_CONTROLLER=nGeert Uytterhoeven2019-11-191-1/+1
| | | | | | | | | | | | | | | | | | Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS, causing failures if reset controller support is not enabled. E.g. on r7s72100/rskrza1: sh-eth e8203000.ethernet: MDIO init failed: -524 sh-eth: probe of e8203000.ethernet failed with error -524 Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb. Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: YueHaibing <yuehaibing@huawei.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mdio_bus: Fix PTR_ERR applied after initialization to constantYueHaibing2019-11-111-5/+6
| | | | | | | | | | | | | | Fix coccinelle warning: ./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 ./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 Fix this by using IS_ERR before PTR_ERR Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds2019-09-181-13/+9
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski. 2) Use bio_vec in the networking instead of custom skb_frag_t, from Matthew Wilcox. 3) Make use of xmit_more in r8169 driver, from Heiner Kallweit. 4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen. 5) Support all variants of 5750X bnxt_en chips, from Michael Chan. 6) More RTNL avoidance work in the core and mlx5 driver, from Vlad Buslov. 7) Add TCP syn cookies bpf helper, from Petar Penkov. 8) Add 'nettest' to selftests and use it, from David Ahern. 9) Add extack support to drop_monitor, add packet alert mode and support for HW drops, from Ido Schimmel. 10) Add VLAN offload to stmmac, from Jose Abreu. 11) Lots of devm_platform_ioremap_resource() conversions, from YueHaibing. 12) Add IONIC driver, from Shannon Nelson. 13) Several kTLS cleanups, from Jakub Kicinski. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits) mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer mlxsw: spectrum: Register CPU port with devlink mlxsw: spectrum_buffers: Prevent changing CPU port's configuration net: ena: fix incorrect update of intr_delay_resolution net: ena: fix retrieval of nonadaptive interrupt moderation intervals net: ena: fix update of interrupt moderation register net: ena: remove all old adaptive rx interrupt moderation code from ena_com net: ena: remove ena_restore_ethtool_params() and relevant fields net: ena: remove old adaptive interrupt moderation code from ena_netdev net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*() net: ena: enable the interrupt_moderation in driver_supported_features net: ena: reimplement set/get_coalesce() net: ena: switch to dim algorithm for rx adaptive interrupt moderation net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable ethtool: implement Energy Detect Powerdown support via phy-tunable xen-netfront: do not assume sk_buff_head list is empty in error handling s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb” net: ena: don't wake up tx queue when down drop_monitor: Better sanitize notified packets ...
| * net: mdio: switch to using gpiod_get_optional()Dmitry Torokhov2019-09-161-13/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MDIO device reset line is optional and now that gpiod_get_optional() returns proper value when GPIO support is compiled out, there is no reason to use fwnode_get_named_gpiod() that I plan to hide away. Let's switch to using more standard gpiod_get_optional() and gpiod_set_consumer_name() to keep the nice "PHY reset" label. Also there is no reason to only try to fetch the reset GPIO when we have OF node, gpiolib can fetch GPIO data from firmwares as well. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | drivers: Introduce device lookup variants by of_nodeSuzuki K Poulose2019-07-301-8/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce wrappers for {bus/driver/class}_find_device() to locate devices by its of_node. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: devicetree@vger.kernel.org Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: linux-i2c@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-spi@vger.kernel.org Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Takashi Iwai <tiwai@suse.com> Cc: Alan Tull <atull@kernel.org> Cc: linux-fpga@vger.kernel.org Cc: Peter Rosin <peda@axentia.se> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Thor Thayer <thor.thayer@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Peter Rosin <peda@axentia.se> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> # I2C part Acked-by: Moritz Fischer <mdf@kernel.org> # For FPGA part Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20190723221838.12024-3-suzuki.poulose@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: mdio: rename mdio_device reset to reset_gpioDavid Bauer2019-04-181-3/+3
| | | | | | | | | | This renames the GPIO reset of mdio devices from 'reset' to 'reset_gpio' to better differentiate between GPIO and reset-controller driven reset line. Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: add support for reset-controllerDavid Bauer2019-04-181-2/+25
| | | | | | | | This commit adds support for PHY reset pins handled by a reset controller. Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-02-241-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | Three conflicts, one of which, for marvell10g.c is non-trivial and requires some follow-up from Heiner or someone else. The issue is that Heiner converted the marvell10g driver over to use the generic c45 code as much as possible. However, in 'net' a bug fix appeared which makes sure that a new local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0 is cleared. Signed-off-by: David S. Miller <davem@davemloft.net>
| * mdio_bus: Fix use-after-free on device_register failsYueHaibing2019-02-221-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | KASAN has found use-after-free in fixed_mdio_bus_init, commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") call put_device() while device_register() fails,give up the last reference to the device and allow mdiobus_release to be executed ,kfreeing the bus. However in most drives, mdiobus_free be called to free the bus while mdiobus_register fails. use-after-free occurs when access bus again, this patch revert it to let mdiobus_free free the bus. KASAN report details as below: BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482 Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524 CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xfa/0x1ce lib/dump_stack.c:113 print_address_description+0x65/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482 fixed_mdio_bus_init+0x283/0x1000 [fixed_phy] ? 0xffffffffc0e40000 ? 0xffffffffc0e40000 ? 0xffffffffc0e40000 do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x462e99 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99 RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003 RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004 Allocated by task 3524: set_track mm/kasan/common.c:85 [inline] __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496 kmalloc include/linux/slab.h:545 [inline] kzalloc include/linux/slab.h:740 [inline] mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143 fixed_mdio_bus_init+0x163/0x1000 [fixed_phy] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 3524: set_track mm/kasan/common.c:85 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:458 slab_free_hook mm/slub.c:1409 [inline] slab_free_freelist_hook mm/slub.c:1436 [inline] slab_free mm/slub.c:2986 [inline] kfree+0xe1/0x270 mm/slub.c:3938 device_release+0x78/0x200 drivers/base/core.c:919 kobject_cleanup lib/kobject.c:662 [inline] kobject_release lib/kobject.c:691 [inline] kref_put include/linux/kref.h:67 [inline] kobject_put+0x146/0x240 lib/kobject.c:708 put_device+0x1c/0x30 drivers/base/core.c:2060 __mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382 fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8881dc824c80 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 248 bytes inside of 2048-byte region [ffff8881dc824c80, ffff8881dc825480) The buggy address belongs to the page: page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0 flags: 0x2fffc0000010200(slab|head) raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800 raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mdio_bus: Fix PTR_ERR() usage after initialization to constantYueHaibing2019-02-181-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | Fix coccinelle warning: ./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44 ./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44 fix this by using IS_ERR before PTR_ERR Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: Convert some PHY and MDIO driver files to SPDX headersAndrew Lunn2019-01-221-6/+1
| | | | | | | | | | | | | | | | Where the license text and the MODULE_LICENSE() value agree, convert to using an SPDX header, removing the license text. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-01-211-0/+1
|\ \ | |/ | | | | | | | | Completely minor snmp doc conflict. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: mdio_bus: add missing device_del() in mdiobus_register() error ↵Thomas Petazzoni2019-01-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | handling The current code in __mdiobus_register() doesn't properly handle failures returned by the devm_gpiod_get_optional() call: it returns immediately, without unregistering the device that was added by the call to device_register() earlier in the function. This leaves a stale device, which then causes a NULL pointer dereference in the code that handles deferred probing: [ 1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074 [ 1.498110] pgd = (ptrval) [ 1.500838] [00000074] *pgd=00000000 [ 1.504432] Internal error: Oops: 17 [#1] SMP ARM [ 1.509133] Modules linked in: [ 1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99 [ 1.520708] Hardware name: Xilinx Zynq Platform [ 1.525261] Workqueue: events deferred_probe_work_func [ 1.530403] PC is at klist_next+0x10/0xfc [ 1.534403] LR is at device_for_each_child+0x40/0x94 [ 1.539361] pc : [<c0683fbc>] lr : [<c0455d90>] psr: 200e0013 [ 1.545628] sp : ceeefe68 ip : 00000001 fp : ffffe000 [ 1.550863] r10: 00000000 r9 : c0c66790 r8 : 00000000 [ 1.556079] r7 : c0457d44 r6 : 00000000 r5 : ceeefe8c r4 : cfa2ec78 [ 1.562604] r3 : 00000064 r2 : c0457d44 r1 : ceeefe8c r0 : 00000064 [ 1.569129] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 1.576263] Control: 18c5387d Table: 0ed7804a DAC: 00000051 [ 1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval)) [ 1.588280] Stack: (0xceeefe68 to 0xceef0000) [ 1.592630] fe60: cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790 [ 1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78 [ 1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac [ 1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10 [ 1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c [ 1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c [ 1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00 [ 1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000 [ 1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4 [ 1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000 [ 1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000 [ 1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94) [ 1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94) [ 1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40) [ 1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c) [ 1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc) [ 1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0) [ 1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154) [ 1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c) [ 1.785689] Exception stack(0xceeeffb0 to 0xceeefff8) [ 1.790739] ffa0: 00000000 00000000 00000000 00000000 [ 1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010) [ 1.819844] ---[ end trace 3c2c0c8b65399ec9 ]--- The actual error that we had from devm_gpiod_get_optional() was -EPROBE_DEFER, due to the GPIO being provided by a driver that is probed later than the Ethernet controller driver. To fix this, we simply add the missing device_del() invocation in the error path. Fixes: 69226896ad636 ("mdio_bus: Issue GPIO RESET to PHYs") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: don't include asm/irq.h directlyHeiner Kallweit2019-01-161-2/+0
|/ | | | | | | | | There's no need to and one shouldn't include asm/irq.h directly. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mdio: remove duplicated include from mdio_bus.cYueHaibing2018-09-171-1/+0
| | | | | | | Remove duplicated include linux/gpio/consumer.h Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: remove PM ops from MDIO busHeiner Kallweit2018-06-051-48/+0
| | | | | | | | | | | | | | | | | | | | | | | | | Current implementation of MDIO bus PM ops doesn't actually implement bus-specific PM ops but just calls PM ops defined on a device level what doesn't seem to be fully in line with the core PM model. When looking e.g. at __device_suspend() the PM core looks for PM ops of a device in a specific order: 1. device PM domain 2. device type 3. device class 4. device bus I think it has good reason that there's no PM ops on device level. Now that a device type representation of PHY's as special type of MDIO devices was added (only user of MDIO bus PM ops), the MDIO bus PM ops can be removed including member pm of struct mdio_device. If for some other type of MDIO device PM ops are needed, it should be modeled as struct device_type as well. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Handle not having GPIO enabled in the kernelAndrew Lunn2018-02-061-1/+2
| | | | | | | | | | | | | If CONFIG_GPIOLIB is disabled, fwnode_get_named_gpiod() becomes a stub function, which return -ENOSYS. Handle this in the same way as -ENOENT, i.e. assume there is no GPIO used to reset the PHYs. Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de> Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mdio: Only perform gpio reset for PHYsAndrew Lunn2018-01-031-4/+17
| | | | | | | | | | | | | | | | Ethernet switch on the MDIO bus have historically performed their own handling of the GPIO reset line. The resent patch to have the MDIO core handle the reset has broken the switch drivers, in that they cannot claim the GPIO. Some switch drivers need more control over the GPIO line than what the MDIO core provides. So restore the historical behaviour by only performing a reset of PHYs, not switches. Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Reported-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mdiobus: add unlocked accessorsRussell King2018-01-031-12/+53
| | | | | | | | | | Add unlocked versions of the bus accessors, which allows access to the bus with all the tracing. These accessors validate that the bus mutex is held, which is a basic requirement for all mii bus accesses. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-12-161-0/+1
|\ | | | | | | | | | | | | Three sets of overlapping changes, two in the packet scheduler and one in the meson-gxl PHY driver. Signed-off-by: David S. Miller <davem@davemloft.net>
| * of_mdio / mdiobus: ensure mdio devices have fwnode correctly populatedRussell King2017-12-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | Ensure that all mdio devices populate the struct device fwnode pointer as well as the of_node pointer to allow drivers that wish to use fwnode APIs to work. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phylib: Add device reset GPIO supportSergei Shtylyov2017-12-051-0/+21
|/ | | | | | | | | | | | | | | | | | | | | | | | | The PHY devices sometimes do have their reset signal (maybe even power supply?) tied to some GPIO and sometimes it also does happen that a boot loader does not leave it deasserted. So far this issue has been attacked from (as I believe) a wrong angle: by teaching the MAC driver to manipulate the GPIO in question; that solution, when applied to the device trees, led to adding the PHY reset GPIO properties to the MAC device node, with one exception: Cadence MACB driver which could handle the "reset-gpios" prop in a PHY device subnode. I believe that the correct approach is to teach the 'phylib' to get the MDIO device reset GPIO from the device tree node corresponding to this device -- which this patch is doing... Note that I had to modify the AT803x PHY driver as it would stop working otherwise -- it made use of the reset GPIO for its own purposes... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Rob Herring <robh@kernel.org> [geert: Propagate actual errors from fwnode_get_named_gpiod()] [geert: Avoid destroying initial setup] [geert: Consolidate GPIO descriptor acquiring code] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "mdio_bus: Remove unneeded gpiod NULL check"Florian Fainelli2017-09-081-2/+4
| | | | | | | | | | | | | | | | This reverts commit 95b80bf3db03c2bf572a357cf74b9a6aefef0a4a ("mdio_bus: Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB checks for NULL descriptors, so it's safe to drop them, but it is not when CONFIG_GPIOLIB is disabled in the kernel. If we do call gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings coming from the inline stubs declared in include/linux/gpio/consumer.h. Fixes: 95b80bf3db03 ("mdio_bus: Remove unneeded gpiod NULL check") Reported-by: Woojung Huh <Woojung.Huh@microchip.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Remove unneeded gpiod NULL checkFabio Estevam2017-07-171-4/+2
| | | | | | | | | The gpiod API checks for NULL descriptors, so there is no need to duplicate the check in the driver. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: use devm_gpiod_get_optional()Sergei Shtylyov2017-06-131-9/+5
| | | | | | | | | The MDIO reset GPIO is really a classical optional GPIO property case, so devm_gpiod_get_optional() should have been used, not devm_gpiod_get(). Doing this saves several LoCs... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: handle only single PHY reset GPIOSergei Shtylyov2017-06-131-34/+19
| | | | | | | | | | Commit 4c5e7a2c0501 ("dt-bindings: mdio: Clarify binding document") declared that a MDIO reset GPIO property should have only a single GPIO reference/specifier, however the supporting code was left intact, still burdening the kernel with now apparently useless loops -- get rid of them. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-06-061-0/+13
|\ | | | | | | | | | | | | Just some simple overlapping changes in marvell PHY driver and the DSA core code. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fix auto-loading of Marvell DSA driverRussell King2017-05-311-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Auto-loading of the Marvell DSA driver has stopped working with recent kernels. This seems to be due to the change of binding for DSA devices, moving them from the platform bus to the MDIO bus. In order for module auto-loading to work, we need to provide a MODALIAS string in the uevent file for the device. However, the device core does not automatically provide this, and needs each bus_type to implement a uevent method to generate these strings. The MDIO bus does not provide such a method, so no MODALIAS string is provided: .# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent DRIVER=mv88e6085 OF_NAME=switch OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4 OF_COMPATIBLE_0=marvell,mv88e6085 OF_COMPATIBLE_N=1 In the case of OF-based devices, the solution is easy - of_device_uevent_modalias() does the work for us. After this is done, the uevent file looks like this: .# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent DRIVER=mv88e6085 OF_NAME=switch OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4 OF_COMPATIBLE_0=marvell,mv88e6085 OF_COMPATIBLE_N=1 MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085 which results in auto-loading of the Marvell DSA driver on Clearfog platforms. Fixes: c0405563a613 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: use of_mdio_parse_addrJon Mason2017-06-021-13/+2
|/ | | | | | | | | | | use of_mdio_parse_addr() in place of an OF read of reg and a bounds check (which is litterally the exact same thing that of_mdio_parse_addr() does) Signed-off-by: Jon Mason <jon.mason@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Call bus->reset() after releasing PHYs from resetFlorian Fainelli2017-05-111-3/+3
| | | | | | | | | | | | | | | The API convention makes it that a given MDIO bus reset should be able to access PHY devices in its reset() callback and perform additional MDIO accesses in order to bring the bus and PHYs in a working state. Commit 69226896ad63 ("mdio_bus: Issue GPIO RESET to PHYs.") broke that contract by first calling bus->reset() and then release all PHYs from reset using their shared GPIO line, so restore the expected functionality here. Fixes: 69226896ad63 ("mdio_bus: Issue GPIO RESET to PHYs.") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Issue GPIO RESET to PHYs.Roger Quadros2017-04-241-0/+47
| | | | | | | | | | | | | | | | | | | | | Some boards [1] leave the PHYs at an invalid state during system power-up or reset thus causing unreliability issues with the PHY which manifests as PHY not being detected or link not functional. To fix this, these PHYs need to be RESET via a GPIO connected to the PHY's RESET pin. Some boards have a single GPIO controlling the PHY RESET pin of all PHYs on the bus whereas some others have separate GPIOs controlling individual PHY RESETs. In both cases, the RESET de-assertion cannot be done in the PHY driver as the PHY will not probe till its reset is de-asserted. So do the RESET de-assertion in the MDIO bus driver. [1] - am572x-idk, am571x-idk, a437x-idk Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Allow building mdio-boardinfo into the kernelFlorian Fainelli2017-03-291-1/+31
| | | | | | | | | | | | | | | | | | | | | | | | | mdio-boardinfo contains code that is helpful for platforms to register specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or CONFIG_PHYLIB will be selected (modular or built-in). In order to make that possible, let's do the following: - descend into drivers/net/phy/ unconditionally - make mdiobus_setup_mdiodev_from_board_info() take a callback argument which allows us not to expose the internal MDIO board info list and mutex, yet maintain the logic within the same file - relocate the code that creates a MDIO device into drivers/net/phy/mdio_bus.c - build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is defined (y or m) Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Allow splitting MDIO bus/device support from PHYsFlorian Fainelli2017-03-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | Introduce a new configuration symbol: MDIO_DEVICE which allows building the MDIO devices and bus code, without pulling in the entire Ethernet PHY library and devices code. PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are updated to reflect that. When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we have mdio-bus.ko as a loadable module, and it does not have a module_exit() function because the safety of removing a bus class is unclear. When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble everything into a common loadable module: libphy.ko because of nasty circular dependencies between phy.c, phy_device.c and mdio_bus.c which are really tough to untangle. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Allow pre-declaration of MDIO devicesFlorian Fainelli2017-02-071-0/+4
| | | | | | | | | | | | Allow board support code to collect pre-declarations for MDIO devices by registering them with mdiobus_register_board_info(). SPI and I2C buses have a similar feature, we were missing this for MDIO devices, but this is particularly useful for e.g: MDIO-connected switches which need to provide their port layout (often board-specific) to a MDIO Ethernet switch driver. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/phy: add trace events for mdio accessesUwe Kleine-König2016-11-241-0/+11
| | | | | | | | Make it possible to generate trace events for mdio read and write accesses. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: don't return NULL from mdiobus_scan()Sergei Shtylyov2016-05-041-1/+1
| | | | | | | | | | I've finally noticed that mdiobus_scan() also returns either NULL or error value on failure. Return ERR_PTR(-ENODEV) instead of NULL since this is the error value already filtered out by the callers that want to ignore the MDIO address scan failure... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Fix MDIO bus scanning in __mdiobus_register()Marek Vasut2016-05-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit b74766a0a0fe ("phylib: don't return NULL from get_phy_device()") in linux-next, phy_get_device() will return ERR_PTR(-ENODEV) instead of NULL if the PHY device ID is all ones. This causes problem with stmmac driver and likely some other drivers which call mdiobus_register(). I triggered this bug on SoCFPGA MCVEVK board with linux-next 20160427 and 20160428. In case of the stmmac, if there is no PHY node specified in the DT for the stmmac block, the stmmac driver ( drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c function stmmac_mdio_register() ) will call mdiobus_register() , which will register the MDIO bus and probe for the PHY. The mdiobus_register() resp. __mdiobus_register() iterates over all of the addresses on the MDIO bus and calls mdiobus_scan() for each of them, which invokes get_phy_device(). Before the aforementioned patch, the mdiobus_scan() would return NULL if no PHY was found on a given address and mdiobus_register() would continue and try the next PHY address. Now, mdiobus_scan() returns ERR_PTR(-ENODEV), which is caught by the 'if (IS_ERR(phydev))' condition and the loop exits immediately if the PHY address does not contain PHY. Repair this by explicitly checking for the ERR_PTR(-ENODEV) and if this error comes around, continue with the next PHY address. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David S. Miller <davem@davemloft.net> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: get_phy_device() doesn't return NULL anymoreSergei Shtylyov2016-04-261-1/+1
| | | | | | | | | Now that get_phy_device() no longer returns NULL on error, we don't need to check for it... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mdio: Fix lockdep falls positive splatAndrew Lunn2016-04-111-2/+2
| | | | | | | | | | | | MDIO devices can be stacked upon each other. The current code supports two levels, which until recently has been enough for a DSA mdio bus on top of another bus. Now we have hardware which has an MDIO mux in the middle. Define an MDIO MUTEX class with three levels. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: NULL dereference on allocation errorDan Carpenter2016-01-121-5/+6
| | | | | | | | | | | If bus = kzalloc() fails then we end up dereferencing bus when we do "bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse the NULL check and return directly on failure. Fixes: e7f4dc3536a4 ('mdio: Move allocation of interrupts into core') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio: Abstract device_remove() and device_free()Andrew Lunn2016-01-071-14/+9
| | | | | | | | | | Make device_free and device_remove operations in the mdio device structure, so the core code does not need to differentiate between phy devices and generic mdio devices. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio: Add support for mdio drivers.Andrew Lunn2016-01-071-2/+11
| | | | | | | | | Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers are PHY drivers. Add support for generic MDIO drivers. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Add comment to mdiobus_scan() and __mdiobus_register()Andrew Lunn2016-01-071-1/+15
| | | | | | | | | | | | | | | Make it clear that mdiobus_scan () will only find devices which have a vendor/product ID in registers 2 and 3. These are typically PHY devices. Other sort of MDIO devices, such as switches, are not expected to be found during the scan. Similarly, __mdiobus_register(), which calls mdiobus_scan() will only find PHY devices, and other sorts of MDIO devices are expected to be instantiated from device tree. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mdio_bus: Generalise of_mdiobus_link_phydev()Andrew Lunn2016-01-071-14/+15
| | | | | | | | | This function should work with any sort of MDIO device which can be probed on the bus, not just PHY devices. So generalise it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: Move phy specific bus match into phy_deviceAndrew Lunn2016-01-071-26/+12
| | | | | | | | | | Matching a driver to a device has both generic parts, and parts which are specific to PHY devices. Move the PHY specific parts into phy_device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: Move PHY PM operations into phy_deviceAndrew Lunn2016-01-071-73/+10
| | | | | | | | | | The MDIO PM operations are really PHY device PM operations. So move them into phy_device. This will be needed when we support devices on the mdio bus which are not PHYs. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy_device: Move phy attributes into phy_deviceAndrew Lunn2016-01-071-42/+0
| | | | | | | | | | | | | | | | | | | | | | The mdio_bus exports three attributes: - PHY ID is the unique 32-bits identifier for a MDIO device implementing standard MII registers MII_PHYSID1/2, which is not guaranteed to be the case for non-standard compliant devices (e.g: Ethernet switches) - PHY interface describes the data-path of the PHY/MDIO device, which is not strictly a PHY thing, but is required and needed for PHY devices to function, a MDIO device could be a control device exclusively - PHY has fixups describes what the PHY driver may have done, so completely PHY specific These are all phy attributes, not generic mdio attributes. So move the attributes into the phy device code. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud