| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/amba_pl022: Fix probe and remove hook section annotations.
spi/mpc5121: change annotations for probe and remove functions
spi/bitbang: reinitialize transfer parameters for every message
spi/spi-gpio: add support for controllers without MISO or MOSI pin
spi/bitbang: add support for SPI_MASTER_NO_{TX, RX} modes
SPI100k: Fix 8-bit and RX-only transfers
spi/mmc_spi: mmc_spi adaptations for SPI bus locking API
spi/mmc_spi: SPI bus locking API, using mutex
Fix trivial conflict in drivers/spi/mpc512x_psc_spi.c due to 'struct
of_device' => 'struct platform_device' rename and __init/__exit to
__devinit/__devexit fix.
|
| | |\ |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Modification of the mmc_spi driver to use the SPI bus locking API.
With this, the mmc_spi driver can be used together with other SPI
devices on the same SPI bus. The exclusive access to the SPI bus is
now managed in the SPI layer. The counting of chip selects in the probe
function is no longer needed.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://codeaurora.org/quic/kernel/dwalker/linux-msm
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
mmc: msm_sdcc: Rename config MMC_MSM7X00A to MMC_MSM
mmc: msm_sdcc: Compile the driver for msm7x30
mmc: msm: fix up build breakage on !PM
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
SD/MMC host controller driver is same for all MSM and QSD
platforms. Hence, rename the config to reflect the same.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The controller base address is referred from platform
resource instead of using #defines. This fixes the
compilation error when driver is compiled for msm7x30.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
with PM disabled I get the following compile error,
drivers/built-in.o: In function `msmsdcc_resume':
linux-2.6/drivers/mmc/host/msm_sdcc.c:1352: undefined reference to `mmc_resume_host'
drivers/built-in.o: In function `msmsdcc_suspend':
linux-2.6/drivers/mmc/host/msm_sdcc.c:1330: undefined reference to `mmc_suspend_host'
This adds ifdefs around the suspend/resume functions to prevent this.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* 'msm-core' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
msm: mmc: Add msm prefix to platform data structure
msm: trout: Remove extern declaration from source file
arm: msm: Fix section mismatch in smd.c.
arm: msm: trout add mmc support
arm: msm: trout: add trout specific gpio interrupts
arm: msm: remove unused #include <linux/version.h>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Rename mmc_platform_data to msm_mmc_platform_data as it is used
only by MSM platform.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mmc_spi: Fix unterminated of_match_table
of/sparc: fix build regression from of_device changes
of/device: Replace struct of_device with struct platform_device
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
commit 2ffe8c5f323c3b9749bf7bc2375d909d20bdbb15 ("of: refactor
of_modalias_node() and remove explicit match table"), introduced
an unterminated of_match_table, which may cause kernel to oops.
This patch fixes the issue by adding an empty device ID.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
- Fix mmc_test_alloc_mem.
- Use nr_free_buffer_pages() instead of sysinfo.totalram to determine
total lowmem pages.
- Change variables containing memory sizes to unsigned long.
- Limit maximum test area size to 128MiB because that is the maximum MMC
high capacity erase size (the maxmium SD allocation unit size is just
4MiB)
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
mmc_test provides tests aimed at testing SD/MMC hosts. This patch adds
performance tests.
It is advantageous to have performance tests in a kernel
module like mmc_test for the following reasons:
- transfer times can be measured very accurately
- arbitrarily large transfers are possible
- the effect of contiguous vs scattered pages
can be determined
The new tests are:
23. Best-case read performance
24. Best-case write performance
25. Best-case read performance into scattered pages
26. Best-case write performance from scattered pages
27. Single read performance by transfer size
28. Single write performance by transfer size
29. Single trim performance by transfer size
30. Consecutive read performance by transfer size
31. Consecutive write performance by transfer size
32. Consecutive trim performance by transfer size
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Secure discard is implemented by Secure Trim if the discard is unaligned
or Secure Erase otherwise.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Disable the data (busy) timeout for erases and set the MMC_CAP_ERASE
capability.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Enable MMC to service discard requests. In the case of SD and MMC cards
that do not support trim, discards become erases. In the case of cards
(MMC) that only allow erases in multiples of erase group size, round to
the nearest completely discarded erase group.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Pablo Castillo <CyberCastle@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Gregg Lebovitz <gregg@lebovitz.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add auto CMD12 command support for eSDHC driver. This is needed by P4080
and P1022 for block read/write. Manual asynchronous CMD12 abort operation
causes protocol violations on these silicons.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds support for regulator API to sdhci core driver.
Regulators can be used to disable power in suspended state to reduce
dissipated energy.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On some Samsung SoCs not all SDHCI controllers have card detect (CD) line.
For some embedded designs it is not even needed, because ususally the
device (like SDIO flash memory or wifi controller) is permanently wired to
the controller. There are also systems which have a card detect line
connected to some of the external interrupt lines or the presence of the
card depends on some other actions (like enabling a power regulator).
This patch adds support for all these cases. The following card detection
methods are possible:
1. internal sdhci host card detect line
2. external event
3. external gpio interrupt
4. no card detect line, controller will poll for the card
5. no card detect line, card is permanently wired to the controller
(once detected host won't poll it any more)
By default, all existing code would use method #1, what is compatible with
the previous version of the driver.
In case of external event, two callbacks must be provided in platdata:
ext_cd_init and ext_cd_cleanup. Both of them get a callback to a function
that notifies the s3c-sdhci host contoller as their argument. That
callback function should be called from the even dispatcher to let host
notice the card insertion/removal.
In case of external gpio interrupt, a gpio pin number must be provided in
platdata (ext_cd_gpio parameter), as well as the information about the
polarity of that gpio pin (ext_cd_gpio_invert). By default
(ext_cd_gpio_invert == 0) gpio value 0 means 'card has been removed', but
this can be changed to 'card has been removed' when ext_cd_gpio_invert ==
1.
This patch adds all required changes to sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch enables SDHCI_QUIRK_NO_HISPD_BIT on Samsung SDHCI driver. This
solves detection problems with some external SD cards. This change has
been tested on S5PC100 and S5PC110. It has no inpact on driver speed.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
S3C SDHCI host controller can change the source for generating mmc clock.
By default host bus clock is used, what causes some problems on machines
with 133MHz bus, because the SDHCI divider cannot be as high get proper
clock value for identification mode. This is not a problem for the
controller, because it can generate lower frequencies from other clock
sources. This patch changes sdhci driver to use get_min_clock() call if
it has been provided.
This fixes the flood of the following warnings on Samsung S5PV210 SoCs:
mmc0: Minimum clock frequency too high for identification mode
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On Samsung's SDMMC hosts the timeout clock is derivied from the SD Clock
which is set dynamically. So checked SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
quirk and removed 'sdhci_s3c_get_timeout_clk' callback which doesn't need
any more.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If other informative interrupts are enabled for the DMA channel used by
hsmmc, those are incorrectly treated as block completion. This patch lets
only the block completion interrupt to be processed.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
CONFIG_MMC_MSM7X00A_RESUME_IN_WQ and CONFIG_MMC_EMBEDDED_SDIO don't exist
in Kconfig and is never defined anywhere else, therefore removing all
references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This will allow us to set up special cards in machine drivers just after
they are detected by MMC core.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There are some chips (like TI WL12xx series) that can be interfaced over
SDIO but don't support the SDIO specification, meaning that they are
missing CIA (Common I/O Area) with all it's registers. Current Linux SDIO
implementation relies on those registers to identify and configure the
card, so non-standard cards can not function and cause lots of warnings
from the core when it reads invalid data from non-existent registers.
After this patch, init_card() host callback can now set new quirk
MMC_QUIRK_NONSTD_SDIO, which means that SDIO core should not try to access
any standard SDIO registers and rely on init_card() to fill all SDIO
structures instead. As those cards are usually embedded chips, all the
required information can be obtained from machine board files by the host
driver when it's called through init_card() callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There's nothing special, just SoC-specific ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Due to build system limitations, intermediate and final objects can't have
the same names. And as we're going to start building SoC-specific
objects, let's rename the module to sdhci-platform, into which we'll link
sdhci-pltfm and SoC-specifc objects.
There should be no issue in renaming as the driver uses modalias
mechanism.
This is exactly the same approach as in sdhci-of driver.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Sometimes want to place SoC-specific parts alongside with the generic
driver, and to do so, we have to switch the driver over to the module
device table matching.
Note that drivers/mmc/host/sdhci-pltfm.h is so far empty, but it'll hold
SoC-specific driver data handlers soon.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Richard R?jfors <richard.rojfors@pelagicore.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch improves low speeds for SD cards.
OMAP-MMC controller's can support maximum bus width of '8'. when bus
width is mentioned as "8" in controller data,the SD stack will check
whether bus width is "4" and if not it will set bus width to "1" and there
by degrading performance. This patch fixes the issue and improves the
performance of SD cards.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A non-zero value of SEC_COUNT does not indicate that the card is sector
addressed. According to the MMC specification, cards with a density
greater than 2GiB are sector addressed.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some host controllers can set mmc->caps before sdhci_add_host().
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some host controllers such as s5pc110 support the WIDE8 feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When using QUIRK_NONSTANDARD_CLOCK, it checks the set_clock() function
which is not used actually. So delete it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The current way of disabling it is not well tested by vendor and has all
kinds of bugs that show up on resume from ram/disk. A very good example
is a dead SDHCI controller.
Old way of disabling is still supported by continuing to use
CONFIG_MMC_RICOH_MMC.
Based on 'http://list.drzeus.cx/pipermail/sdhci-devel/2007-December/002085.html'
Therefore most of the credit for this goes to Andrew de Quincey
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Philip Langdale <philipl@overt.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This series adds support for SD combo cards to MMC/SD driver stack.
SD combo consists of SD memory and SDIO parts in one package. Since the
parts have a separate SD command sets, after initialization, they can be
treated as independent cards on one bus.
Changes are divided into two patches. First is just moving initialization
code around so that SD memory part init can be called from SDIO init.
Second patch is a proper change enabling SD memory along SDIO. I tried to
move as much no-op changes to the first patch so that it's easier to
follow the required changes to initialization flow for SDIO cards.
This is based on Simplified SDIO spec v.2.00. The init sequence is
slightly modified to follow current SD memory init implementation.
Command sequences, assuming SD memory and SDIO indeed ignore unknown
commands, are the same as before for both parts.
This patch:
Prepare for SD-combo (IO+mem) support by splitting SD memory
card init and related functions.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure
version 3 and version 3 have to check the CSD_STRUCTURE byte in the
EXT_CSD register.
Also fix EXT_CSD revision message.
[akpm@linux-foundation.org: fix comment, per Chris Ball]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This removes q->prepare_flush_fn completely (changes the
blk_queue_ordered API).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
| |\ \ \ \ \
| |_|/ / /
|/| | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
|
| | | |_|/
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove cs_types.h which is no longer needed: Most definitions aren't
used at all, a few can be made away with, and two remaining definitions
(typedefs, unfortunatley) may be moved to more specific places.
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
|
| | |\ \ \ \
| | |/ / /
| | | | |
| | | | |
| | | | | |
Conflicts:
arch/sparc/kernel/prom_64.c
|
