summaryrefslogtreecommitdiffstats
path: root/drivers/media/pci/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* [media] pci: Add tw5864 driverAndrey Utkin2016-08-241-0/+1
| | | | | | | | | | | | | | | | Support for boards based on Techwell TW5864 chip which provides multichannel video & audio grabbing and encoding (H.264, MJPEG, ADPCM G.726). This submission implements only H.264 encoding of all channels at D1 resolution. Thanks to Mark Thompson <sw@jkqxz.net> for help, and for contribution of H.264 startcode emulation prevention code. Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* [media] media: Support Intersil/Techwell TW686x-based video capture cardsEzequiel Garcia2016-04-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit introduces the support for the Techwell TW686x video capture IC. This hardware supports a few DMA modes, including scatter-gather and frame (contiguous). This commit makes little use of the DMA engine and instead has a memcpy based implementation. DMA frame and scatter-gather modes support may be added in the future. Currently supported chips: - TW6864 (4 video channels), - TW6865 (4 video channels, not tested, second generation chip), - TW6868 (8 video channels but only 4 first channels using built-in video decoder are supported, not tested), - TW6869 (8 video channels, second generation chip). [mchehab@osg.samsung.com: make checkpatch happy by using "unsigned int" instead of just "unsigned"] Cc: Krzysztof Halasa <khalasa@piap.pl> Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driverKozlov Sergey2015-08-111-1/+2
| | | | | | | | | | | | | | Add NetUP Dual Universal CI PCIe board driver. The board has - two CI slots - two I2C adapters - SPI master bus for accessing flash memory containing FPGA firmware No changes required. Signed-off-by: Kozlov Sergey <serjk@netup.ru> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] cobalt: add new driverHans Verkuil2015-05-201-0/+1
| | | | | | | | | | | | | | The cobalt device is a PCIe card with 4 HDMI inputs (adv7604) and a connector that can be used to hook up an adv7511 transmitter or an adv7842 receiver daughterboard. This device is used within Cisco but is sadly not available outside of Cisco. Nevertheless it is a very interesting driver that can serve as an example of how to support HDMI hardware and how to use the popular adv devices. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] dt3155: move out of staging into drivers/media/pciHans Verkuil2015-05-011-0/+1
| | | | | | | | | The dt3155 code is now in good shape, so move it out of staging into drivers/media/pci. Mark in MAINTAINERS that I'll do Odd Fixes for this driver. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] smipcie: SMI pcie bridge driver for DVBSky S950 V3 dvb-s/s2 cardsnibble.max2014-11-031-1/+2
| | | | | | | | | | | | | | | | | | | There is a new PCIe bridge chip(from SMI) used in DVBSky V3 seris cards, include S950 V3 and S952 V3 cards. SMI pcie bridge chip is PCIe 1.1 compliant, supports MSI feature. Main interface blocks: 1>Two DVB transport stream input ports(ts0,ts1). 2>Two I2C master bus(i2c0, i2c1). 3>IR controller. 4>reset pins and other GPIOs. DVBSky S950 V3 card has a single channel of dvb-s/s2. 1>Frontend: tuner: M88TS2022, demod: M88DS3103 2>PCIe bridge: SMI PCIe The current driver does not support SMI IR function. [mchehab@osg.samsung.com: fix Makefile to find m88ts2022.h] Signed-off-by: Max nibble <nibble.max@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] pt3: add support for Earthsoft PT3 ISDB-S/T receiver cardAkihiro Tsukada2014-09-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for PT3 PCIe cards. PT3 has an FPGA PCIe bridge chip, a TC90522 demod chip and a VA4M6JC2103 tuner module which contains two QM1D1C0042 chips for ISDB-S and two MxL301RF's for ISDB-T. It can receive and deliver 4 (2x ISDB-S, 2x ISDB-T) streams simultaneously, and a kthread is used per stream to poll incoming data, because PT3 does not have interrupts. As an antenna input for each delivery system is split in the tuner module and shared between the corresponding two tuner chips, LNB/LNA controls that the FPGA chip provides are (naturally) shared as well. The tuner chips also share the power line in the tuner module, which is controlled on/off by a GPIO pin of the demod chip. As with the demod chip and the ISDB-T tuner chip, the init sequences/register settings for those chips are not disclosed and stored in a private memory of the FPGA, PT3 driver executes the init of those chips on behalf of their drivers. Signed-off-by: Akihiro Tsukada <tskd08@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* [media] tw68: refactor and cleanup the tw68 driverHans Verkuil2014-09-041-0/+1
| | | | | | | | | | Refactor and clean up the tw68 driver. It's now using the proper V4L2 core frameworks. Tested with my Techwell tw6805a and tw6816 grabber boards. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] drivers: media: pci: Makefile: Remove duplicate subdirectory from obj-yAndreas Ruprecht2014-08-211-1/+0
| | | | | | | | | | In the list of subdirectories compiled, b2c2/ appears twice. This patch removes one of the appearances. Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] solo6x10: move out of staging into drivers/media/pci.Hans Verkuil2014-07-221-0/+1
| | | | | | | | | | Now that the custom motion detection API has been replaced with a standard API there is no reason anymore to keep it in staging. So (finally!) move it to drivers/media/pci. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] Fix some Makefile rulesMauro Carvalho Chehab2012-08-161-1/+1
| | | | | | | | | | | | | | On a few places, := were using instead of +=, causing drivers to not compile. While here, standardize the usage of += on all cases where multiple lines are needed, and for obj-y/obj-m targets, and := when just one line is needed, on <module>-obj rules. Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Identified-by: Antti Polosaari <crope@iki.fi> Tested-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] move the remaining PCI devices to drivers/media/pciMauro Carvalho Chehab2012-08-151-0/+2
| | | | | | Move meye and sta2x11_vip into the drivers/media/pci subdirs. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] move analog PCI saa7146 drivers to its own dirMauro Carvalho Chehab2012-08-151-1/+2
| | | | | | | Instead of having them under drivers/media/video, move them to their own directory. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] rename most media/video pci drivers to media/pciMauro Carvalho Chehab2012-08-151-1/+10
| | | | | | | | Rename all PCI drivers with their own directory under drivers/media/video into drivers/media/pci and update the building system. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] b2c2: break it into common/pci/usb directoriesMauro Carvalho Chehab2012-08-131-1/+2
| | | | | | | b2c2 is, in fact, 2 drivers: one for PCI and one for USB, plus a common bus-independent code. Break it accordingly. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] Rename media/dvb as media/pciMauro Carvalho Chehab2012-08-131-0/+13
The remaining dvb drivers are pci, so rename them to match the bus. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OpenPOWER on IntegriCloud