| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.
For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.
We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
- We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
which causes the recovery not be be checkpointed.
- We remove spares and then re-added them which loses important state
information.
The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed. If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error. So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.
Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded). Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.
Issue: If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available, do we want to:
1/ complete the current rebuild, then go back and rebuild the new spare or
2/ restart the rebuild from the start and rebuild both devices in
parallel.
Both options can be argued for. The code currently takes option 2 as
a/ this requires least code change
b/ this results in a minimally-degraded array in minimal time.
Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character. It may also output a trailing space
before newline. klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file. This looks ugly.
Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar. Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
| |
As this is more in line with common practice in the kernel. Also swap the
args around to be more like list_for_each.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
| |
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
| |
Then we can get rid of ->issue_flush_fn() and all the driver private
implementations of that.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
| |
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
|
| |
A recent fix which made sure ->degraded was initialised properly exposed a
second bug - ->degraded wasn't been updated when drives failed or were
hot-added.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
Two less-used md personalities have bugs in the calculation of ->degraded (the
extent to which the array is degraded).
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
raid1, raid10 and multipath don't report their 'congested' status through
bdi_*_congested, but should.
This patch adds the appropriate functions which just check the 'congested'
status of all active members (with appropriate locking).
raid1 read_balance should be modified to prefer devices where
bdi_read_congested returns false. Then we could use the '&' branch rather
than the '|' branch. However that should would need some benchmarking first
to make sure it is actually a good idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
This patch changes a mempool user, which is basically just a wrapper around
kzalloc(), to use the common mempool_kmalloc/kfree, rather than its own
wrapper function, removing duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Decrease the number of pointer derefs in drivers/md/multipath.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Alasdair G Kergon <agk@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
| |
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).
These personalities have fairly artificial 'numbers'. The numbers
are use to:
1- provide an index into an array where the various personalities
are recorded
2- identify the module (via an alias) which implements are particular
personality.
Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely). Module identification can be done using an alias
based on level rather than 'personality' number.
The current 'raid5' modules support two level (4 and 5) but only one
personality. This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.
With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.
This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
| |
Replace multiple kmalloc/memset pairs with kzalloc calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
| |
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
in md
Acked-by: <paulmck@us.ibm.com>
Signed-off-by: Suzanne Wood <suzannew@cs.pdx.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
| |
md does not yet support BIO_RW_BARRIER, so be honest about it and fail
(-EOPNOTSUPP) any such requests.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
This patch removes some unneeded checks of pointers being NULL before
calling kfree() on them. kfree() handles NULL pointers just fine, checking
first is pointless.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
committed to creation
We we set the too early, they may still be in place and possibly get called
even though the array didn't get set up properly.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
This patch makes some needlessly global identifiers static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Arjan van de Ven <arjanv@infradead.org>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
| |
|
|
|
|
|
|
|
|
| |
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
