summaryrefslogtreecommitdiffstats
path: root/drivers/gpio
Commit message (Collapse)AuthorAgeFilesLines
...
| * gpio: mb86s7x: Handle return value of clk_prepare_enable.Arvind Yadav2017-08-141-1/+3
| | | | | | | | | | | | | | clk_prepare_enable() can fail here and we must check its return value. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: it87: add support for IT8772F Super I/O.Diego Elio Pettenò2017-08-141-0/+3
| | | | | | | | | | | | | | | | From the datasheet, the GPIO interface is identical to IT8728 (same description), so just add it to the same case as the other chip. Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Use unsigned int where possibleThierry Reding2017-08-141-32/+24
| | | | | | | | | | | | | | | | | | In most of the cases, integers in this file can't be negative, so the type can be more restricted for clarity. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Fix checkpatch warningsThierry Reding2017-08-141-12/+20
| | | | | | | | | | | | | | | | | | | | Fix a couple of checkpatch warnings, such as complaints about bare unsigned being used (instead of unsigned int) and missing blank lines after declarations. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Prefer kcalloc() over kzalloc() with multipliesThierry Reding2017-08-141-2/+2
| | | | | | | | | | | | | | | | | | Rather than manually compute the size of an array, pass the number and element size to kcalloc(). Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Remove unnecessary checkThierry Reding2017-08-141-9/+2
| | | | | | | | | | | | | | | | | | of_device_get_match_data() can never return NULL, therefore the check for NULL values is unnecessary. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: sysfs: Fixup kerneldocThierry Reding2017-08-141-4/+4
| | | | | | | | | | | | | | Fix up some references to parameters to match the code. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: acpi: Fixup kerneldocThierry Reding2017-08-141-2/+2
| | | | | | | | | | | | | | | | | | | | Fix up a parameter description to match the code and fix markup for a constant to prettify output. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: devres: Improve kerneldocThierry Reding2017-08-141-0/+3
| | | | | | | | | | | | | | Add missing descriptions for some parameters to match the code. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: of: Improve kerneldocThierry Reding2017-08-141-4/+3
| | | | | | | | | | | | | | | | Add descriptions for missing fields and fix up some parameter references to match the code. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: Cleanup kerneldocThierry Reding2017-08-141-22/+60
| | | | | | | | | | | | | | | | | | Some kerneldoc has become stale or wasn't quite correct from the outset. Fix up the most serious issues to silence warnings when building the documentation. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Use platform_get_irq()Thierry Reding2017-08-141-5/+5
| | | | | | | | | | | | | | | | | | Instead of using platform_get_resource() and getting the interrupts from the resource, use platform_get_irq() which is slightly easier to use and covers some special cases that the former doesn't. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: Use platform_irq_count()Thierry Reding2017-08-141-7/+6
| | | | | | | | | | | | | | Use platform_irq_count() instead of open-coding the same code sequence. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: Convert to using %pOF instead of full_nameRob Herring2017-08-1410-35/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Tien Hock Loh <thloh@altera.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: davinci: Convert prinkt to dev_errKeerthy2017-08-141-2/+1
| | | | | | | | | | | | | | In case of devm_clk_get failure use dev_err instead of printk Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: davinci: Use devm_gpiochip_add_data in place of gpiochip_add_dataKeerthy2017-08-141-2/+12
| | | | | | | | | | | | | | | | | | Use the devm version of gpiochip_add_data and pass on the return value. This avoids memory leak due to gpiochip_add_data in case the driver is unbound. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: altera-a10sr: constify gpio_chip structureGustavo A. R. Silva2017-08-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This structure is only used to copy into another structure, so declare it as const. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct gpio_chip i@p = { ... }; @ok@ identifier r.i; expression e; position p; @@ e = i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct gpio_chip e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct gpio_chip i = { ... }; In the following log you can see a significant difference in the code size and data segment, hence in the dec segment. This log is the output of the size command, before and after the code change: before: text data bss dec hex filename 1954 600 0 2554 9fa drivers/gpio/gpio-altera-a10sr.o after: text data bss dec hex filename 1655 512 0 2167 877 drivers/gpio/gpio-altera-a10sr.o Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: gpio-mxc: gpio_set_wake_irq() use proper return valuesPhilipp Rosenberger2017-08-141-5/+6
| | | | | | | | | | | | | | | | | | Errors from enable_irq_wake() in gpio_set_wake_irq() were silently ignored. Thus led to the problem that gpio_set_wake_irq() always returned successfully, even if enable_irq_wake() returned an error. Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: rcar: add gen[123] fallback compatibility stringsSimon Horman2017-08-141-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add fallback compatibility string for R-Car Gen 1, 2 and 3. In the case of Renesas R-Car hardware we know that there are generations of SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship between IP blocks might be. For example, I believe that r8a7790 is older than r8a7791 but that doesn't imply that the latter is a descendant of the former or vice versa. We can, however, by examining the documentation and behaviour of the hardware at run-time observe that the current driver implementation appears to be compatible with the IP blocks on SoCs within a given generation. For the above reasons and convenience when enabling new SoCs a per-generation fallback compatibility string scheme being adopted for drivers for Renesas SoCs. Also deprecate renesas,gpio-rcar as its name is more generic than its implementation. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: replace __maybe_unused in gpiolib.h with static inlineMasahiro Yamada2017-08-141-1/+1
| | | | | | | | | | | | | | In header files, static inline is more commonly used. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: tegra: remove gpio_to_irq() from hw irq handlersGrygorii Strashko2017-08-141-1/+2
| | | | | | | | | | | | | | | | | | gpio_to_irq() API expected to be used by GPIO consumers and not drivers and there are no guarantee that its gpiolib implementation is irq safe. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: pxa: remove gpio_to_irq() from hw irq handlersGrygorii Strashko2017-08-141-3/+5
| | | | | | | | | | | | | | | | | | gpio_to_irq() API expected to be used by GPIO consumers and not drivers and there are no guarantee that its gpiolib implementation is irq safe. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpiolib: allow gpio irqchip to map irqs dynamicallyGrygorii Strashko2017-08-141-23/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now IRQ mappings are always created for all (allowed) GPIOs in gpiochip in gpiochip_irqchip_add_key() which goes against the idea of SPARSE_IRQ and, as result, leads to: - increasing of memory consumption for IRQ descriptors most of which will never ever be used (espessially on platform with a high number of GPIOs). (sizeof(struct irq_desc) == 256 on my tested platforms) - imposibility to use GPIO irqchip APIs by gpio drivers when HW implements GPIO IRQ functionality as IRQ crossbar/router which has only limited number of IRQ outputs (example from [1], all GPIOs can be mapped on only 8 IRQs). Hence, remove static IRQ mapping code from gpiochip_irqchip_add_key() and instead replace irq_find_mapping() with irq_create_mapping() in gpiochip_to_irq(). Also add additional gpiochip_irqchip_irq_valid() calls in gpiochip_to_irq() and gpiochip_irq_map(). After this change gpio2irq mapping will happen the following way when GPIO irqchip APIs are used by gpio driver: - IRQ mappings will be created statically if driver passes first_irq>0 vlaue in gpiochip_irqchip_add_key(). - IRQ mappings will be created dynamically from gpio_to_irq() or of_irq_get(). Tested on am335x-evm and dra72-evm-revc. - dra72-evm-revc: number of created irq mappings decreased from 402 -> 135 Mem savings 267*256 = 68352 (66kB) - am335x-evm: number of created irq mappings decreased from 188 -> 63 Mem savings 125*256 = 32000 (31kB) [1] https://lkml.org/lkml/2017/6/15/428 Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpiolib: request the gpio before querying its directionTimur Tabi2017-08-141-0/+11
| | | | | | | | | | | | | | | | | | | | Before querying a GPIO to determine its direction, the GPIO should be formally requested. This allows the GPIO driver to block access to unavailable GPIOs, which makes it easier for some drivers to support sparse GPIO maps. Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * gpio: pca953x: remove incorrect le16_to_cpu callsAndy Shevchenko2017-08-141-5/+3
| | | | | | | | | | | | | | | | | | | | | | i2c_smbus commands handle the correct byte order for smbus transactions internally. This will currently result in incorrect operation on big endian systems. Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: mvebu: Fix cause computation in irq handlerGregory CLEMENT2017-08-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When switching to regmap, the way to compute the irq cause was reorganized. However while doing it, a typo was introduced: a 'xor' replaced a 'and'. This lead to wrong behavior in the interrupt handler ans one of the symptom was wrong irq handler called on the Armada 388 GP: "->handle_irq(): c016303c, handle_bad_irq+0x0/0x278 ->irq_data.chip(): c0b0ec0c, 0xc0b0ec0c ->action(): (null) IRQ_NOPROBE set IRQ_NOREQUEST set unexpected IRQ trap at vector 00 irq 0, desc: ee804800, depth: 1, count: 0, unhandled: 0" Fixes: 2233bf7a92e7 ("gpio: mvebu: switch to regmap for register access") Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: reject invalid gpio before getting gpio_descMasami Hiramatsu2017-08-141-2/+8
|/ | | | | | | | | | | | | | | | | Check user-given gpio number and reject it before calling gpio_to_desc() because gpio_to_desc() is for kernel driver and it expects given gpio number is valid (means 0 to 511). If given number is invalid, gpio_to_desc() calls WARN() and dump registers and stack for debug. This means user can easily kick WARN() just by writing invalid gpio number (e.g. 512) to /sys/class/gpio/export. Fixes: 0e9a5edf5d01 ("gpio: fix deferred probe detection for legacy API") Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpio: tegra: fix unbalanced chained_irq_enter/exitMichał Mirosław2017-08-021-3/+3
| | | | | | | | | | | When more than one GPIO IRQs are triggered simultaneously, tegra_gpio_irq_handler() called chained_irq_exit() multiple times for one chained_irq_enter(). Fixes: 3c92db9ac0ca3eee8e46e2424b6c074e2e394ad9 Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> [Also changed the variable to a bool] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpiolib: skip unwanted events, don't convert them to opposite edgeBartosz Golaszewski2017-08-011-5/+4
| | | | | | | | | | | | | | The previous fix for filtering out of unwatched events was not entirely correct. Instead of skipping the events we don't want, they are now interpreted as events with opposing edge. In order to fix it: always read the GPIO line value on interrupt and only emit the event if it corresponds with the event type we requested. Cc: stable@vger.kernel.org Fixes: ad537b822577 ("gpiolib: fix filtering out unwanted events") Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpio: exar: Use correct property prefix and document bindingsJan Kiszka2017-08-011-1/+1
| | | | | | | | | | | | | | The device-specific property should be prefixed with the vendor name, not "linux,", as Linus Walleij pointed out. Change this and document the bindings of this platform device. We didn't ship the old binding in a release yet. So we can still change it without breaking an official API. Fixes: 380b1e2f3a2f ("gpio-exar/8250-exar: Make set of exported GPIOs configurable") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake sourcePhilipp Rosenberger2017-08-011-0/+3
| | | | | | | | | | | | In the function gpio_set_wake_irq(), port->irq_high is only checked for zero. As platform_get_irq() returns a value less then zero if no interrupt was found, any gpio >= 16 was handled like an irq_high interrupt was available. On iMX27 for example no high interrupt is available. This lead to the problem that only some gpios (the lower 16) were useable as wake sources. Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHYMasahiro Yamada2017-08-011-0/+1
| | | | | | | | This driver calls irq_domain_hierarchy() and irq_chip_*_parent(). They are available only when CONFIG_IRQ_DOMAIN_HIERARCHY is enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpio: lp87565: Set proper output level and direction for direction_outputAxel Lin2017-07-311-22/+24
| | | | | | | | | | The value argument of lp87565_gpio_direction_output() means output level rather than gpio direction. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge (most of) tag 'mfd-next-4.13' of ↵Linus Torvalds2017-07-071-1/+13
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "New Drivers: - Intel Cherry Trail Whiskey Cove PMIC - TI LP87565 PMIC New Device Support: - Add support for Cannonlake to intel-lpss-pci - Add support for Simatic IOT2000 to intel_quark_i2c_gpio New Functionality: - Add Regulator support (axp20x) Fix-ups: - Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec) - Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core) - Provide deregistration on unbind (rn5t618) - Rework DT code/documentation (arizona) - Constify things (fsl-imx25-tsadc) - MAINTAINERS updates (DA9062/61) - Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C) - Switch to DMI matching (intel_quark_i2c_gpio) - Provide an appropriate level of error checking (wm831x-{i2c,spi}, twl4030-irq, tc6393xb) - Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc, stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc, exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099, motorola-cpcap)" [ Skipped the last commit in that series that added eight thousand lines of pointless repeated register definitions. - Linus ] * tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits) mfd: Add LP87565 PMIC support mfd: cros_ec: Free IRQ on exit dt-bindings: vendor-prefixes: Add arctic to vendor prefix mfd: da9061: Fix to remove BBAT_CONT register from chip model mfd: da9061: Fix to remove BBAT_CONT register from chip model mfd: axp20x-i2c: Document that this must be builtin on x86 mfd: Add Cherry Trail Whiskey Cove PMIC driver mfd: tc6393xb: Handle return value of clk_prepare_enable mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency mfd: motorola-cpcap: Use devm_of_platform_populate() mfd: smsc-ece: Use devm_of_platform_populate() mfd: qcom-spmi-pmic: Use devm_of_platform_populate() mfd: palmas: Use devm_of_platform_populate() mfd: exynos: Use devm_of_platform_populate() mfd: fsl-imx25: Use devm_of_platform_populate() mfd: cros_ec: Use devm_of_platform_populate() mfd: atmel: Use devm_of_platform_populate() mfd: stm32-timers: Use devm_of_platform_populate() mfd: intel_soc_pmic: Select designware i2c-bus driver ...
| * mfd: intel_soc_pmic_bxtwc: Remove second level IRQ for gpio deviceKuppuswamy Sathyanarayanan2017-06-191-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently all PMIC GPIO domain IRQs are consumed by the same device(bxt_wcove_gpio), so there is no need to export them as separate interrupts. We can just export only the first level GPIO IRQ(BXTWC_GPIO_LVL1_IRQ) as an IRQ resource and let the GPIO device driver(bxt_wcove_gpio) handle the GPIO sub domain IRQs based on status value of GPIO level2 interrupt status register. Also, just using only the first level IRQ will eliminate the bug involved in requesting only the second level IRQ and not explicitly enable the first level IRQ. For more info on this issue please read the details at, https://lkml.org/lkml/2017/2/27/148 This patch also makes relevant change in Whiskey cove GPIO driver to use only first level PMIC GPIO IRQ. Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
* | Merge tag 'gpio-v4.13-1' of ↵Linus Torvalds2017-07-0724-425/+1188
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.13 series. Some administrativa: I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO driver coming in through this tree, along with a whole bunch of Exar 8250 fixes. These are ACKed by Greg and also hit drivers/platform/* where they are ACKed by Andy Shevchenko. Speaking about drivers/platform/* there is also a bunch of ACPI stuff coming through that route, again ACKed by Andy. The MCP23S08 changes are coming in here as well. You already have the commits in your tree, so this is just a result of sharing an immutable branch between pin control and GPIO. Core: - Export add/remove for lookup tables so that modules can export GPIO descriptor tables. - Handle GPIO sleep states: it is now possible to flag that a GPIO line may loose its state during suspend/resume of the system to save power. This is used in the Wolfson Micro Arizona driver. - ACPI-based GPIO was tightened up a lot around the edges. - Use bitmap_fill() to speed up a loop. New drivers: - Exar XRA1403 SPI-based GPIO. - MVEBU driver now supports Armada 7K and 8K. - LP87565 PMIC GPIO. - Renesas R-CAR R8A7743 (RZ/G1M). - The new IOT2040 8250 serial/GPIO also comes in through this changeset. Substantial driver changes: - Seriously fix the Exar 8250 GPIO portions to work. - The MCP23S08 was moved out to a pin control driver. - Convert MEVEBU to use regmap for register access. - Drop Vulcan support from the Broadcom driver. - Serious cleanup and improvement of the mockup driver, giving us a better test coverage. Misc: - Lots of janitorial clean up. - A bunch of documentation fixes" * tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits) serial: exar: Add support for IOT2040 device gpio-exar/8250-exar: Make set of exported GPIOs configurable platform: Accept const properties serial: exar: Factor out platform hooks gpio-exar/8250-exar: Rearrange gpiochip parenthood gpio: exar: Fix iomap request gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards serial: uapi: Add support for bus termination gpio: rcar: Add R8A7743 (RZ/G1M) support gpio: gpio-wcove: Fix GPIO control register offset calculation gpio: lp87565: Add support for GPIO gpio: dwapb: fix missing first irq for edgeboth irq type MAINTAINERS: Take maintainership for GPIO ACPI support gpio: exar: Fix reading of directions and values gpio: exar: Allocate resources on behalf of the platform device gpio-exar/8250-exar: Fix passing in of parent PCI device gpio: mockup: use devm_kcalloc() where applicable gpio: mockup: add myself as author gpio: mockup: improve the error message gpio: mockup: don't return magic numbers from probe() ...
| * | gpio-exar/8250-exar: Make set of exported GPIOs configurableJan Kiszka2017-07-031-23/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the rest is required to operate the UART. To allow modeling this case, expand the platform device data structure to specify a (consecutive) pin subset for exporting by the gpio-exar driver. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
| * | gpio-exar/8250-exar: Rearrange gpiochip parenthoodJan Kiszka2017-07-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the parent of the exar gpiochip to its platform device, like other gpiochips are doing it. In order to keep the relationship discoverable for ACPI systems, set the platform device companion to the PCI device. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: exar: Fix iomap requestJan Kiszka2017-07-031-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | The UART driver already maps the resource for us. Trying to do this here only fails and leaves us with a non-working device. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cardsJan Kiszka2017-07-031-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commtech adapters need the MPIOs for internal purposes, and the gpio-exar driver already refused to pick them up. But there is actually no point in even creating the underlying platform device. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | gpio: rcar: Add R8A7743 (RZ/G1M) supportBiju Das2017-06-291-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Renesas RZ/G1M (R8A7743) SoC GPIO blocks are identical to the R-Car Gen2 family. Add support for its GPIO controllers. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: gpio-wcove: Fix GPIO control register offset calculationKuppuswamy Sathyanarayanan2017-06-291-24/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to Whiskey Cove PMIC GPIO controller specification, for GPIO pins 0-12, GPIO input and output register control address range from, 0x4e44-0x4e50 for GPIO outputs control register 0x4e51-0x4e5d for GPIO input control register But, currently when calculating the GPIO register offsets in to_reg() function, all GPIO pins in the same bank uses the same GPIO control register address. This logic is incorrect. This patch fixes this issue. This patch also adds support to selectively skip register modification for virtual GPIOs. In case of Whiskey Cove PMIC, ACPI code may use up 94 virtual GPIOs. These virtual GPIOs are used by the ACPI code as means to access various non GPIO bits of PMIC. So for these virtual GPIOs, we don't need to manipulate the physical GPIO pin register. A similar patch has been merged recently by Hans for Crystal Cove PMIC GPIO driver. You can find more details about it in Commit 9a752b4c9ab9 ("gpio: crystalcove: Do not write regular gpio registers for virtual GPIOs") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reported-by: Jukka Laitinen <jukka.laitinen@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: lp87565: Add support for GPIOKeerthy2017-06-213-0/+201
| | | | | | | | | | | | | | | | | | | | | | | | Add driver for lp87565 PMIC family GPIOs. Three GPIOs are supported and can be configured in Open-drain output or Push-pull output. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: dwapb: fix missing first irq for edgeboth irq typeXiaoguang Chen2017-06-211-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dwapb_irq_set_type overwrites polarity register value for IRQ_TYPE_EDGE_BOTH case. If the polarity of one gpio is 0 by default, then it will set falling edge irq trigger. and the gpio may requires rising edge irq for the first time, and it will be missed. Do not overwrite polarity register for IRQ_TYPE_EDGE_BOTH case can solve this issue. Signed-off-by: Xiaoguang Chen <xgchenshy@gmail.com> Tested-by: Jisheng Zhang <jszhang@marvell.com> [Fix some really weird text encoding problem] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: exar: Fix reading of directions and valuesJan Kiszka2017-06-201-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | First, the logic for translating a register bit to the return code of exar_get_direction and exar_get_value were wrong. And second, there was a flip regarding the register bank in exar_get_direction. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: exar: Allocate resources on behalf of the platform deviceJan Kiszka2017-06-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not allocate resources on behalf of the parent device but on our own. Otherwise, cleanup does not properly work if gpio-exar is removed but not the parent device. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio-exar/8250-exar: Fix passing in of parent PCI deviceJan Kiszka2017-06-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes reloading of the GPIO driver for the same platform device instance as created by the exar UART driver: First of all, the driver sets drvdata to its own value during probing and does not restore the original value on exit. But this won't help anyway as the core clears drvdata after the driver left. Set the platform device parent instead. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mockup: use devm_kcalloc() where applicableBartosz Golaszewski2017-06-201-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | When allocating a zeroed array of objects use devm_kcalloc() instead of manually calculating the required size and using devm_kzalloc(). Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mockup: add myself as authorBartosz Golaszewski2017-06-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Just taking credit for the recent changes and new features. :) Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mockup: improve the error messageBartosz Golaszewski2017-06-201-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | Indicate the error number and make the message a bit more elaborate. Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenPOWER on IntegriCloud