summaryrefslogtreecommitdiffstats
path: root/drivers/bluetooth
Commit message (Collapse)AuthorAgeFilesLines
* Bluetooth: Introduce a flags variable to Three-wire UART stateJohan Hedberg2012-07-171-11/+15
| | | | | | | | This patch introduces a flags variable to the Three-wire UART state struct and converts the two existing bools in the struct into flags. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Improve Three-wire UART configuration handlingJohan Hedberg2012-07-171-7/+27
| | | | | | | | | | | The configuration request/response messages contain a configuration field which contains the sliding window size (amount of unacked reliable packets that can be pending). This patch makes sure that we configure the correct size (minimum of local and remote values) and use it when determining whether to send new packets or not. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Remove unnecessary h5_build_pkt functionJohan Hedberg2012-07-171-26/+23
| | | | | | | | | The implementation of h5_build_packet can be moved into h5_prepare_pkt since all h5_prepare_pkt does is determine whether the packet is reliable and then call h5_build_packet. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Implement proper low-power support for Three-wire UARTJohan Hedberg2012-07-171-5/+32
| | | | | | | | | | | | This patch adds on-demand wakeup request sending (and re-sendind) when we are in low-power state. When the controller enters this state it will send a sleep message after which the host is not allowed to send any other packets until a wakeup request has been sent and the woken message received as a response to it. The wakeup requests are re-sent periodically until a woken message is received. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add initialization tracking to HCI Three-wire driverJohan Hedberg2012-07-171-16/+50
| | | | | | | | | | | This patch adds tracking for the uninitialized, initialized and active states for Three-wire UART. This is needed so we can handle periodic sending of the Link Establishment messages before reaching active state and so that we do not try to do any higher level HCI data transmission before reaching active state. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add initial sleep support to Three-wire UARTJohan Hedberg2012-07-171-0/+13
| | | | | | | | | | This patch adds very basic support for the sleep related messages. The only thing the code does right now is send a wakeup message as soon as receiving a sleep one, essentially preventing the controller from going to sleep. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Improve rx debug logs for Three-wire UARTJohan Hedberg2012-07-171-14/+3
| | | | | | | Remove unnecessary debug logs and add some to more centralized places. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Use delayed init for Three-wire UARTJohan Hedberg2012-07-171-0/+3
| | | | | | | | This patch takes into use the delayed initialization feature that the Bluetooth UART framework provides. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add delayed init sequence support for UART controllersJohan Hedberg2012-07-172-1/+43
| | | | | | | | | | This patch makes it possible to have UART drivers perform an internal initialization before calling hci_register_dev. This allows moving a lot of init code from user space (hciattach) to the kernel side, thereby creating a more controlled/robust initialization process. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Simplify hci_uart_tty_close logicJohan Hedberg2012-07-171-12/+13
| | | | | | | | This patch cleans up and reduces indentation in the hci_uart_tty_close function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add support for Three-wire Link Control packetsJohan Hedberg2012-07-171-17/+79
| | | | | | | | This patch adds basic support for parsing and sending Three-wire UART Link Control packets. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Fix/implement Three-wire reliable packet sendingJohan Hedberg2012-07-171-17/+70
| | | | | | | | This patch should complete the necessary code for sending reliable Three-wire packets. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add Three-wire header value convenience macrosJohan Hedberg2012-07-171-0/+8
| | | | | | | | This patch adds convenience macros for reading Three-wire header values. This will help make the code more readable. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add initial packet sending support to Three-wire UARTJohan Hedberg2012-07-171-7/+98
| | | | | | | | This patch adds initial packed encoding and sending support to the Three-wire UART HCI transport driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add basic packet parsing to Three-wire UART driverJohan Hedberg2012-07-171-8/+222
| | | | | | | | This patch adds basic packet parsing to the Three-wire UART HCI driver for packets received from the controller. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add initial reliable packet support for Three-wire UARTJohan Hedberg2012-07-171-0/+56
| | | | | | | | This patch adds initial support for reliable packets along with the necessary retransmission timer for the Three-wire UART HCI driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Add basic state tracking to Three-wire UART driverJohan Hedberg2012-07-171-4/+92
| | | | | | | | This patch adds basic state tracking and socket buffer handling to the Three-wire UART (H5) HCI driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Initial skeleton for Three-wire UART (H5) supportJohan Hedberg2012-07-175-0/+112
| | | | | | | | This patch adds the initial skeleton for Three-wire UART (H5) support and hooks it up to the HCI UART framework. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: btmrvl: trivial style fixesAndrei Emeltchenko2012-07-092-4/+7
| | | | | | | | | Patch shortens locals scope and adds missing braces. This is a diff between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do not send vendor events to bluetooth stack". Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: bluecard_cs: Shorten scope for iobaseAndrei Emeltchenko2012-06-301-2/+4
| | | | | | | | | | | | | Shortening scope shall silence some warnings reported by Geert Uytterhoeven: ... drivers/bluetooth/bluecard_cs.c: warning: unused variable 'iobase' [-Wunused-variable] ... Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Fix warning: using int as NULL pointerAndrei Emeltchenko2012-06-302-2/+2
| | | | | | | | | | | | | | Fix for warnings below: ... drivers/bluetooth/bt3c_cs.c:667:20: warning: Using plain integer as NULL pointer drivers/bluetooth/btuart_cs.c:596:20: warning: Using plain integer as NULL pointer ... Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: cleanup dtl1_configDevendra Naga2012-06-301-8/+10
| | | | | | | Improve the error handling of dtl1_config() Signed-off-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Merge branch 'for-upstream' of ↵Gustavo Padovan2012-06-265-6/+23
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
| * Bluetooth: btmrvl: Do not send vendor events to bluetooth stackAndrei Emeltchenko2012-06-193-6/+18
| | | | | | | | | | | | | | | | Vendor-specific events shall be processed in driver and not sent to bluetooth stack where they screw up HCI command countings. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
| * Bluetooth: add support for atheros 0930:0219Giancarlo Formicuccia2012-06-112-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ. usb-devices shows: T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0219 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
| * Bluetooth: Support AR3011 in Acer Iconia Tab W500Marek Vasut2012-06-092-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Acer used this chip connected via USB: Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x3005 AR3011 Bluetooth bcdDevice 0.01 iManufacturer 0 iProduct 0 iSerial 0 bNumConfigurations 1 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* | Bluetooth: btmrvl: add SD8787 Bluetooth AMP device IDBing Zhao2012-06-051-0/+3
| | | | | | | | | | | | | | SD8787 SDIO function 3 (device ID 0x911B) is for Bluetooth AMP. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* | Bluetooth: Remove unnecessary headers includeGustavo Padovan2012-06-051-8/+0
| | | | | | | | | | | | | | | | | | Most of the include were unnecessary or already included by some other header. Replace module.h by export.h where possible. Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* | Bluetooth: Remove 'register' usage from the subsystemGustavo Padovan2012-06-057-16/+16
| | | | | | | | | | | | | | Let the compiler chooses what is best. Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* | Bluetooth: Rename HCI_QUIRK_NO_RESET to HCI_QUIRK_RESET_ON_CLOSESzymon Janc2012-06-053-5/+5
|/ | | | | | | | | HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to reset device on close instead of init, not to not reset at all. Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion. Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2012-05-247-34/+164
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull more networking updates from David Miller: "Ok, everything from here on out will be bug fixes." 1) One final sync of wireless and bluetooth stuff from John Linville. These changes have all been in his tree for more than a week, and therefore have had the necessary -next exposure. John was just away on a trip and didn't have a change to send the pull request until a day or two ago. 2) Put back some defines in user exposed header file areas that were removed during the tokenring purge. From Stephen Hemminger and Paul Gortmaker. 3) A bug fix for UDP hash table allocation got lost in the pile due to one of those "you got it.. no I've got it.." situations. :-) From Tim Bird. 4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll try to coalesce overlapping frags and crash. Fix from Eric Dumazet. 5) RCU routing table lookups can race with free_fib_info(), causing crashes when we deref the device pointers in the route. Fix by releasing the net device in the RCU callback. From Yanmin Zhang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits) tcp: take care of overlaps in tcp_try_coalesce() ipv4: fix the rcu race between free_fib_info and ip_route_output_slow mm: add a low limit to alloc_large_system_hash ipx: restore token ring define to include/linux/ipx.h if: restore token ring ARP type to header xen: do not disable netfront in dom0 phy/micrel: Fix ID of KSZ9021 mISDN: Add X-Tensions USB ISDN TA XC-525 gianfar:don't add FCB length to hard_header_len Bluetooth: Report proper error number in disconnection Bluetooth: Create flags for bt_sk() Bluetooth: report the right security level in getsockopt Bluetooth: Lock the L2CAP channel when sending Bluetooth: Restore locking semantics when looking up L2CAP channels Bluetooth: Fix a redundant and problematic incoming MTU check Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C Bluetooth: Fix EIR data generation for mgmt_device_found Bluetooth: Fix Inquiry with RSSI event mask Bluetooth: improve readability of l2cap_seq_list code Bluetooth: Fix skb length calculation ...
| * Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03CMichael Gruetzner2012-05-162-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to the blacklist of btusb module and add it to the ath3k module to properly load the firmware in Kernel 3.3.4 The device is integrated in e.g. some Acer Aspire 7750G. Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e03c Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Michael Gruetzner <mgruetzn@gmx.de> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: btmrvl: add support for SDIO suspend/resume callbacksAmitkumar Karwar2012-05-093-1/+104
| | | | | | | | | | | | | | | | | | | | | | Host sleep is activated using already configured host sleep parameters in suspend handler and it is cancelled in resume handler. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: btmrvl: configure default host sleep parametersAmitkumar Karwar2012-05-093-22/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently debugfs commands "hscfgcmd" and "gpiogap" are provided for host sleep configuration. But if user doesn't configure host sleep parameters using these commands, host sleep activation is failed during suspend (support for suspend and resume handlers is added in next patch). Default host sleep configuration is done during driver initialisation in this patch. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: btusb: Dynamic alternate settingMikel Astiz2012-05-091-2/+11
| | | | | | | | | | | | | | | | | | | | | | The alternate setting must be dynamically set according to the number of active SCO links, and the bit depth of the audio. The possible values for the alternate setting are described in the Bluetooth Core Specification, Volume 4, Part B, section 2.1.1. Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: btmrvl_sdio: remove pointless conditional before release_firmware()Jesper Juhl2012-05-091-7/+2
| | | | | | | | | | | | | | | | release_firmware() deals gracefullt with NULL pointers so there's no reason to test for one prior to calling the function. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: vhci: Ignore return code of nonseekable_open()David Herrmann2012-05-091-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The comment in ./fs/open.c clearly states that nonseekable_open() will never fail. Therefore, we can safely ignore the return code. This is the recommended way to deal with nonseekable_open(). Our current code looks like nonseekable_open() is checked for the return code. However, if we check the return code, we must also kfree() our private data if the open fails. To avoid this overhead and to avoid confusion, we simply drop the return code and return 0. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
| * Bluetooth: Remove redundant hdev->parent fieldDavid Herrmann2012-05-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We initialize the "struct device" in hci_alloc_dev() for a long time now so we can access hdev->dev.parent directly. Hence, we can drop the temporary field hdev->parent which is used in no other place than hci_add_sysfs(). SET_HCIDEV_DEV() is never called after registering a device by the drivers so we do not overwrite internal device-state. Furthermore, hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the default behavior with dev.parent = NULL is kept. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* | USB: Disable hub-initiated LPM for comms devices.Sarah Sharp2012-05-185-0/+5
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* Merge branch 'for-upstream' of ↵John W. Linville2012-04-272-0/+10
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
| * Add Foxconn / Hon Hai IDs for btusb moduleSteven Harms2012-04-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This change adds 0x0489:0xe033 to the btusb module. This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook. Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e033 Rev= 2.29 S: Manufacturer=Broadcom Corp S: Product=Acer Module S: SerialNumber=60D819F74101 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Steven Harms <sjharms@gmail.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: Add support for AR3012 [0cf3:e004]AceLan Kao2012-04-192-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add another vendor specific ID for Atheros AR3012 output of usb-devices: T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e004 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/922715 Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| * Bluetooth: Add support for Atheros [13d3:3362]AceLan Kao2012-04-132-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add another vendor specific ID for Atheros AR3012 device. This chip is wrapped by IMC Networks. output of usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3362 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
| * Bluetooth: btusb: Add vendor specific ID (0489 e042) for BCM20702A0Manoj Iyer2012-04-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e042 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DCA61B5 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Reported-by: Dennis Chua <dennis.chua@canonical.com> Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* | Merge branch 'master' of ↵John W. Linville2012-04-093-2/+9
|\ \ | |/ | | | | git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
| * Bluetooth: btusb: typo in Broadcom SoftSailing idDon Zickus2012-03-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I was trying to backport the following commit to RHEL-6 From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001 From: Oliver Neukum <oliver@neukum.org> Date: Wed, 21 Sep 2011 11:37:15 +0200 Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing and noticed it wasn't working on an HP Elitebook. Looking into the patch I noticed a very subtle typo in the ids. The patch has '0x05ac' instead of '0x0a5c'. A snippet of the lsusb -v output also shows this: Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 1 bDeviceProtocol 1 bMaxPacketSize0 64 idVendor 0x0a5c Broadcom Corp. idProduct 0x21e1 bcdDevice 1.12 iManufacturer 1 Broadcom Corp iProduct 2 BCM20702A0 iSerial 3 60D819F0338C bNumConfigurations 1 Looking at other Broadcom ids, the fix matches them whereas the original patch matches Apple's ids. Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads correctly. Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
| * Bluetooth: Add support for Atheros [04ca:3005]AceLan Kao2012-03-282-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add another vendor specific ID for Atheros AR3012 device. This chip is wrapped by Lite-On Technology Corp. output of usb-devices: T: Bus=04 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3005 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
| * Bluetooth: hci_ldisc: fix NULL-pointer dereference on tty_closeJohan Hovold2012-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not close protocol driver until device has been unregistered. This fixes a race between tty_close and hci_dev_open which can result in a NULL-pointer dereference. The line discipline closes the protocol driver while we may still have hci_dev_open sleeping on the req_lock mutex resulting in a NULL-pointer dereference when lock is acquired and hci_init_req called. Bug is 100% reproducible using hciattach and a disconnected serial port: 0. # hciattach -n ttyO1 any noflow 1. hci_dev_open called from hci_power_on grabs req lock 2. hci_init_req executes but device fails to initialise (times out eventually) 3. hci_dev_open is called from hci_sock_ioctl and sleeps on req lock 4. hci_uart_tty_close detaches protocol driver and cancels init req 5. hci_dev_open (1) releases req lock 6. hci_dev_open (3) grabs req lock, calls hci_init_req, which triggers oops when request is prepared in hci_uart_send_frame [ 137.201263] Unable to handle kernel NULL pointer dereference at virtual address 00000028 [ 137.209838] pgd = c0004000 [ 137.212677] [00000028] *pgd=00000000 [ 137.216430] Internal error: Oops: 17 [#1] [ 137.220642] Modules linked in: [ 137.223846] CPU: 0 Tainted: G W (3.3.0-rc6-dirty #406) [ 137.230529] PC is at __lock_acquire+0x5c/0x1ab0 [ 137.235290] LR is at lock_acquire+0x9c/0x128 [ 137.239776] pc : [<c0071490>] lr : [<c00733f8>] psr: 20000093 [ 137.239776] sp : cf869dd8 ip : c0529554 fp : c051c730 [ 137.251800] r10: 00000000 r9 : cf8673c0 r8 : 00000080 [ 137.257293] r7 : 00000028 r6 : 00000002 r5 : 00000000 r4 : c053fd70 [ 137.264129] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000001 [ 137.270965] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 137.278717] Control: 10c5387d Table: 8f0f4019 DAC: 00000015 [ 137.284729] Process kworker/u:1 (pid: 7, stack limit = 0xcf8682e8) [ 137.291229] Stack: (0xcf869dd8 to 0xcf86a000) [ 137.295776] 9dc0: c0529554 00000000 [ 137.304351] 9de0: cf8673c0 cf868000 d03ea1ef cf868000 000001ef 00000470 00000000 00000002 [ 137.312927] 9e00: cf8673c0 00000001 c051c730 c00716ec 0000000c 00000440 c0529554 00000001 [ 137.321533] 9e20: c051c730 cf868000 d03ea1f3 00000000 c053b978 00000000 00000028 cf868000 [ 137.330078] 9e40: 00000000 00000000 00000002 00000000 00000000 c00733f8 00000002 00000080 [ 137.338684] 9e60: 00000000 c02a1d50 00000000 00000001 60000013 c0969a1c 60000093 c053b96c [ 137.347259] 9e80: 00000002 00000018 20000013 c02a1d50 cf0ac000 00000000 00000002 cf868000 [ 137.355834] 9ea0: 00000089 c0374130 00000002 00000000 c02a1d50 cf0ac000 0000000c cf0fc540 [ 137.364410] 9ec0: 00000018 c02a1d50 cf0fc540 00000000 cf0fc540 c0282238 c028220c cf178d80 [ 137.372985] 9ee0: 127525d8 c02821cc 9a1fa451 c032727c 9a1fa451 127525d8 cf0fc540 cf0ac4ec [ 137.381561] 9f00: cf0ac000 cf0fc540 cf0ac584 c03285f4 c0328580 cf0ac4ec cf85c740 c05510cc [ 137.390136] 9f20: ce825400 c004c914 00000002 00000000 c004c884 ce8254f5 cf869f48 00000000 [ 137.398712] 9f40: c0328580 ce825415 c0a7f914 c061af64 00000000 c048cf3c cf8673c0 cf85c740 [ 137.407287] 9f60: c05510cc c051a66c c05510ec c05510c4 cf85c750 cf868000 00000089 c004d6ac [ 137.415863] 9f80: 00000000 c0073d14 00000001 cf853ed8 cf85c740 c004d558 00000013 00000000 [ 137.424438] 9fa0: 00000000 00000000 00000000 c00516b0 00000000 00000000 cf85c740 00000000 [ 137.433013] 9fc0: 00000001 dead4ead ffffffff ffffffff c0551674 00000000 00000000 c0450aa4 [ 137.441589] 9fe0: cf869fe0 cf869fe0 cf853ed8 c005162c c0013b30 c0013b30 00ffff00 00ffff00 [ 137.450164] [<c0071490>] (__lock_acquire+0x5c/0x1ab0) from [<c00733f8>] (lock_acquire+0x9c/0x128) [ 137.459503] [<c00733f8>] (lock_acquire+0x9c/0x128) from [<c0374130>] (_raw_spin_lock_irqsave+0x44/0x58) [ 137.469360] [<c0374130>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c02a1d50>] (skb_queue_tail+0x18/0x48) [ 137.479339] [<c02a1d50>] (skb_queue_tail+0x18/0x48) from [<c0282238>] (h4_enqueue+0x2c/0x34) [ 137.488189] [<c0282238>] (h4_enqueue+0x2c/0x34) from [<c02821cc>] (hci_uart_send_frame+0x34/0x68) [ 137.497497] [<c02821cc>] (hci_uart_send_frame+0x34/0x68) from [<c032727c>] (hci_send_frame+0x50/0x88) [ 137.507171] [<c032727c>] (hci_send_frame+0x50/0x88) from [<c03285f4>] (hci_cmd_work+0x74/0xd4) [ 137.516204] [<c03285f4>] (hci_cmd_work+0x74/0xd4) from [<c004c914>] (process_one_work+0x1a0/0x4ec) [ 137.525604] [<c004c914>] (process_one_work+0x1a0/0x4ec) from [<c004d6ac>] (worker_thread+0x154/0x344) [ 137.535278] [<c004d6ac>] (worker_thread+0x154/0x344) from [<c00516b0>] (kthread+0x84/0x90) [ 137.543975] [<c00516b0>] (kthread+0x84/0x90) from [<c0013b30>] (kernel_thread_exit+0x0/0x8) [ 137.552734] Code: e59f4e5c e5941000 e3510000 0a000031 (e5971000) [ 137.559234] ---[ end trace 1b75b31a2719ed1e ]--- Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
| * Bluetooth: Add Atheros maryann PIDVID supportCho, Yu-Chen2012-03-282-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Atheros maryann 0cf3:311d PIDVID support This module is AR3012 Series. Include /sys/kernel/debug/usb/devices output here for reference before: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.01 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms after: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Cho, Yu-Chen <acho@suse.com> cked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
| * Bluetooth: btusb: Add USB device ID "0a5c 21e8"João Paulo Rechi Vita2012-03-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | One more vendor-specific ID for BCM20702A0. T: Bus=01 Lev=03 Prnt=05 Port=02 Cnt=01 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21e8 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=00027221F4E2 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: João Paulo Rechi Vita <jprvita@openbossa.org> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
OpenPOWER on IntegriCloud