summaryrefslogtreecommitdiffstats
path: root/drivers/bluetooth/bpa10x.c
Commit message (Collapse)AuthorAgeFilesLines
* USB: convert drivers/bluetooth/* to use module_usb_driver()Greg Kroah-Hartman2011-11-181-14/+1
| | | | | | | | | | | | | This converts the drivers in drivers/bluetooth/* to use the module_usb_driver() macro which makes the code smaller and a bit simpler. Added bonus is that it removes some unneeded kernel log messages about drivers loading and/or unloading. Cc: Marcel Holtmann <marcel@holtmann.org> Cc: "Gustavo F. Padovan" <padovan@profusion.mobi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Bluetooth: Use __packed annotation for driversGustavo F. Padovan2010-07-211-1/+1
| | | | | | | Use the __packed annotation instead of the __attribute__((packed)). Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Convert controller hdev->type to hdev->busMarcel Holtmann2010-02-271-1/+1
| | | | | | | The hdev->type is misnamed and should be actually hdev->bus instead. So convert it now. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Enable per-module dynamic debug messagesMarcel Holtmann2008-11-301-5/+0
| | | | | | | | | | | With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to allow debugging without having to recompile the kernel. This patch turns all BT_DBG() calls into pr_debug() to support dynamic debug messages. As a side effect all CONFIG_BT_*_DEBUG statements are now removed and some broken debug entries have been fixed. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Send HCI Reset command by default on device initializationMarcel Holtmann2008-11-301-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The Bluetooth subsystem was not using the HCI Reset command when doing device initialization. The Bluetooth 1.0b specification was ambiguous on how the device firmware was suppose to handle it. Almost every device was triggering a transport reset at the same time. In case of USB this ended up in disconnects from the bus. All modern Bluetooth dongles handle this perfectly fine and a lot of them actually require that HCI Reset is sent. If not then they are either stuck in their HID Proxy mode or their internal structures for inquiry and paging are not correctly setup. To handle old and new devices smoothly the Bluetooth subsystem contains a quirk to force the HCI Reset on initialization. However maintaining such a quirk becomes more and more complicated. This patch turns the logic around and lets the old devices disable the HCI Reset command. The only device where the HCI_QUIRK_NO_RESET is still needed are the original Digianswer devices and dongles with an early CSR firmware. CSR reported that they fixed this for version 12 firmware. The last official release of version 11 firmware is build ID 115. The first version 12 candidate was build ID 117. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* bpa10x: free sk_buff with kfree_skbIlpo Järvinen2008-10-311-2/+2
| | | | | | | | | | Inspired by Sergio Luis' similar patches, I finally found a case which is trivial enough that spatch won't choke on it. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [Bluetooth] Fix double frees on error paths of btusb and bpa10x driversMarcel Holtmann2008-10-061-2/+0
| | | | | | | | | | The transfer buffer of an URB will be automatically freed when using the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will cause a double free. Reported-by: Justin Mattock <justinmattock@gmail.com> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* [Bluetooth] Removal of unnecessary ignore module parameterMarcel Holtmann2008-08-071-9/+1
| | | | | | | | This removes the unnecessary ignore parameter, which is useless. There are alternate methods of kicking a driver off an USB device. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* drivers/bluetooth/bpa10x.c: fix memleakAdrian Bunk2008-02-051-0/+1
| | | | | | | | This patch fixea a memleak spotted by the Coverity checker. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [Bluetooth] Change BPA 100/105 driver to use USB anchorsMarcel Holtmann2007-10-221-362/+262
| | | | | | | | With the new support for USB anchors the driver can become more simpler and also cleaner. This patch switches to the usage of USB anchors for all URBs. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* [SK_BUFF]: Introduce skb_copy_from_linear_data{_offset}Arnaldo Carvalho de Melo2007-04-251-2/+2
| | | | | | | To clearly state the intent of copying from linear sk_buffs, _offset being a overly long variant but interesting for the sake of saving some bytes. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells2006-10-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* Remove obsolete #include <linux/config.h>Jörn Engel2006-06-301-1/+0
| | | | | Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* [PATCH] USB: remove .owner field from struct usb_driverGreg Kroah-Hartman2006-01-041-1/+0
| | | | | | It is no longer needed, so let's remove it, saving a bit of memory. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [Bluetooth]: Add endian annotations to the coreMarcel Holtmann2005-11-081-2/+2
| | | | | | | This patch adds the endian annotations to the Bluetooth core. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [PATCH] bluetooth: kmalloc + memset -> kzalloc conversionDeepak Saxena2005-11-071-3/+1
| | | | | | | Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [Bluetooth] Ignore additional interfaces of BPA 100/105 devicesMarcel Holtmann2005-10-281-0/+3
| | | | | | | If a BPA 100/105 device contains more then one interface then ignore the additional interfaces, because they are unused. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* [PATCH] gfp flags annotations - part 1Al Viro2005-10-081-1/+1
| | | | | | | | | | | | - added typedef unsigned int __nocast gfp_t; - replaced __nocast uses for gfp flags with gfp_t - it gives exactly the same warnings as far as sparse is concerned, doesn't change generated code (from gcc point of view we replaced unsigned int with typedef) and documents what's going on far better. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [Bluetooth]: Move packet type into the SKB control bufferMarcel Holtmann2005-08-291-7/+7
| | | | | | | | | This patch moves the usage of packet type into the SKB control buffer. After this patch it is now possible to shrink the sk_buff structure and redefine its pkt_type. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [Bluetooth]: Fix sparse warnings (__nocast type)Victor Fusco2005-08-291-1/+2
| | | | | | | | | | This patch fixes the sparse warnings "implicit cast to nocast type" for the priority or gfp_mask parameters of the memory allocations. Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br> Signed-off-by: Domen Puncer <domen@coderock.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [Bluetooth] Kill redundant NULL checks before kfree()Marcel Holtmann2005-08-061-5/+2
| | | | | | | There's no need to check for NULL before calling kfree() on a pointer. Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds2005-04-161-0/+657
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
OpenPOWER on IntegriCloud