summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_it821x.c
Commit message (Collapse)AuthorAgeFilesLines
* pata_it821x: use raw nbytes in check_atapi_dmaTejun Heo2008-03-241-1/+1
| | | | | | | | pata_it821x needs to look at raw request size in check_atapi_dma(). Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata/pata_it821x: Improve handling of poorly compatible emulationsAlan Cox2008-01-231-2/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Some it821x RAID firmwares return 0 for the err return off both devices. A similar issue occurs with the slave returning 0 not 1 if you plug a gigabyte sata ramdisk into a controller that fakes two SATA ports as master/slave on an SFF channel. The patch does the following - Allow the 'failed diagnostics' case on both master and slave - Move the HORKAGE_DIAGNOSTIC check after ->dev_config This second change also allows IT821x to fix up a problem where we report drive diagnostic failures when in fact the drive is fine but the microcontroller firmware doesn't appear to get it right. IT821x clears the flag again to avoid giving the user bogus warnings about their disk. The other IT821x change is a bit ugly, we slightly abuse the cable type hook to fiddle with the identify data for the devices. We could add a new hook for this but as we have only one offender and no more seeming likely it seems better to keep libata-core clean. Please let this sit in -mm briefly, just in case the relaxed checking breaks some other emulated interface. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix misspellings of "system", "controller", "interrupt" and "necessary".Robert P. J. Day2007-10-191-2/+2
| | | | | | | | Fix the various misspellings of "system", controller", "interrupt" and "[un]necessary". Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Adrian Bunk <bunk@kernel.org>
* libata: Switch most of the remaining SFF drivers to ata_sff_port_startAlan Cox2007-10-121-1/+1
| | | | | | | | This avoids allocating DMA buffers if not needed but at the moment is mostly just a neatness item. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Remove ->port_disable() hookJeff Garzik2007-10-121-2/+0
| | | | | | | | It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik2007-10-121-2/+0
| | | | | | | | | | | | | * ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-link: linkify config/EH related functionsTejun Heo2007-10-121-3/+3
| | | | | | | | | | | | | Make the following functions deal with ata_link instead of ata_port. * ata_set_mode() * ata_eh_autopsy() and related functions * ata_eh_report() and related functions * suspend/resume related functions * ata_eh_recover() and related functions Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-link: implement and use link/device iteratorsTejun Heo2007-10-121-3/+2
| | | | | | | | | | | | | | | | | Multiple links and different number of devices per link should be considered to iterate over links and devices. This patch implements and uses link and device iterators - ata_port_for_each_link() and ata_link_for_each_dev() - and ata_link_max_devices(). This change makes a lot of functions iterate over only possible devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such changes have been examined and nothing should be broken. While at it, add a separating comment before device helpers to distinguish them better from link helpers and others. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-link: introduce ata_linkTejun Heo2007-10-121-2/+2
| | | | | | | | | | | | | | | | | | | Introduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link. This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port. This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_it821x: fix lost interrupt with atapi devicesJeff Norden2007-09-101-0/+4
| | | | | | | | | | | | | | | | | Fix "lost" interrupt problem when using dma with CD/DVD drives in some configurations. This problem can make installing linux from media impossible for distro's that have switched to libata-only configurations. The simple fix is to eliminate the use of dma for reading drive status, etc, by checking the number of bytes to transferred. This change will only affect the behavior of atapi devices, not disks. There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229 This patch is for 2.6.22.1 Signed-off-by: Jeff Norden <jnorden@math.tntech.edu> Reviewed-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Bump driver versionsJeff Garzik2007-08-311-1/+1
| | | | | | | Bump the versions for drivers that were modified, but had not already had a version number bump. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_it821x: Fix regression/corruptorAlan Cox2007-08-231-1/+1
| | | | | | | | | | | | Whoever did the PCI revision patch slipped up on the it821x, and I didn't spot this at the time either. They moved the check for the errata from the 0x10 revision to 0x11. Put it back This one is important for 2.6.23 final as in some cases bad things will occur if 0x10 revision boards don't get the fixups. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* PCI: Change all drivers to use pci_device->revisionAuke Kok2007-07-111-2/+1
| | | | | | | | | | | | | | | | | | | | Instead of all drivers reading pci config space to get the revision ID, they can now use the pci_device->revision member. This exposes some issues where drivers where reading a word or a dword for the revision number, and adding useless error-handling around the read. Some drivers even just read it for no purpose of all. In devices where the revision ID is being copied over and used in what appears to be the equivalent of hotpath, I have left the copy code and the cached copy as not to influence the driver's performance. Compile tested with make all{yes,mod}config on x86_64 and i386. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Acked-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [libata] Use ATA_UDMAx standard masks when filling driver's udma_mask infoJeff Garzik2007-07-091-1/+1
| | | | | | | | | The ATA_UDMAx masks are self-documenting, and far better than manually writing in the hex mask. Note that pata_it8213 mask differed from the comment. Added a FIXME there. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] PATA drivers: remove ATA_FLAG_SRSTJeff Garzik2007-07-091-2/+2
| | | | | | | This flag only has meaning in old-EH drivers, and these drivers have already been converted to the new EH. Remove. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_it821x: fix section mismatch warningRandy Dunlap2007-06-271-1/+1
| | | | | | | | | | | Fix section mismatch when CONFIG_HOTPLUG=n (but functions are used for resume): WARNING: drivers/ata/pata_it821x.o(.text+0x3f): Section mismatch: reference to .init.text: (between 'it821x_reinit_one' and 'it821x_program_udma') WARNING: drivers/ata/pata_it821x.o(.text+0x691): Section mismatch: reference to .init.text: (between 'it821x_init_one' and 'it821x_passthru_set_dmamode') Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* fix module_param mistake in it821xStas Sergeev2007-06-201-1/+1
| | | | | | | | | | The attached patch fixes a trivial mistake in a MODULE_PARAM_DESC of pata_it821x driver. The parameter name in MODULE_PARAM_DESC should match the one in module_param_named. Signed-off-by: Stas Sergeev <stsp@aknet.ru> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_it821x: (partially) fix DMA in RAID modeBartlomiej Zolnierkiewicz2007-06-201-8/+3
| | | | | | | | | | | | | | | | | | | | Code intended to check DMA status was checking DMA command register. Moreover firmware seems to "forget" to set DMA capable bit for the slave device (at least in RAID mode but without ITE RAID volumes) so check device ID for DMA capable bit when deciding whether to use DMA and remove DMA status check completely. Thanks to Pavol Simo for the bugreport and testing the initial fix. This change unfortunately still doesn't fix DMA in RAID mode (which works fine with IDE it821x) but Alan is working on the missing pieces (pata_it821x vs libata EH issues). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata: TriviaAlan Cox2007-05-251-2/+1
| | | | | | | Typo/comment fixes Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: clean up SFF init messTejun Heo2007-05-111-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: reimplement suspend/resume support using sdev->manage_start_stopTejun Heo2007-05-111-4/+0
| | | | | | | | | | | | | | | | | | | | | | | Reimplement suspend/resume support using sdev->manage_start_stop. * Device suspend/resume is now SCSI layer's responsibility and the code is simplified a lot. * DPM is dropped. This also simplifies code a lot. Suspend/resume status is port-wide now. * ata_scsi_device_suspend/resume() and ata_dev_ready() removed. * Resume now has to wait for disk to spin up before proceeding. I couldn't find easy way out as libata is in EH waiting for the disk to be ready and sd is waiting for EH to complete to issue START_STOP. * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config(). This fixes spindown on shutdown and suspend-to-disk. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Update several PATA drivers for new ->cable_detect hookJeff Garzik2007-04-281-28/+5
| | | | | | | All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007. I merely combined them all into a single patch. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: dev_config does not need ap and adev passingAlan2007-04-281-2/+1
| | | | | | | | | | It used to be impossible to get from ata_device to ata_port but that is no longer true. Various methods have been cleaned up over time but dev_config still takes both and most users don't need both anyway. Tidy this one up Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: add missing CONFIG_PM in LLDsTejun Heo2007-03-021-0/+6
| | | | | | | | Add missing #ifdef CONFIG_PM conditionals around all PM related parts in libata LLDs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] bump versionsJeff Garzik2007-02-261-1/+1
| | | | | | Bump versions based on changes submitted during 2.6.21 merge window. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: Use new id_to_dma_mode function to tidy reporting in more drivers ↵Alan2007-02-251-0/+2
| | | | | | | (minimally tested) Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: add another IRQ calls (libata drivers)Akira Iguchi2007-02-091-0/+4
| | | | | | | | | | | | | | | | | | This patch is against each libata driver. Two IRQ calls are added in ata_port_operations. - irq_on() is used to enable interrupts. - irq_ack() is used to acknowledge a device interrupt. In most drivers, ata_irq_on() and ata_irq_ack() are used for irq_on and irq_ack respectively. In some drivers (ex: ahci, sata_sil24) which cannot use them as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: convert to iomapTejun Heo2007-02-091-3/+3
| | | | | | | | | | | | | | | | Convert libata core layer and LLDs to use iomap. * managed iomap is used. Pointer to pcim_iomap_table() is cached at host->iomap and used through out LLDs. This basically replaces host->mmio_base. * if possible, pcim_iomap_regions() is used Most iomap operation conversions are taken from Jeff Garzik <jgarzik@pobox.com>'s iomap branch. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: update libata LLDs to use devresTejun Heo2007-02-091-25/+3
| | | | | | | | | | | | | | | | | Update libata LLDs to use devres. Core layer is already converted to support managed LLDs. This patch simplifies initialization and fixes many resource related bugs in init failure and detach path. For example, all converted drivers now handle ata_device_add() failure gracefully without excessive resource rollback code. As most resources are released automatically on driver detach, many drivers don't need or can do with much simpler ->{port|host}_stop(). In general, stop callbacks are need iff port or host needs to be given commands to shut it down. Note that freezing is enough in many cases and ports are automatically frozen before being detached. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: use ata_id_c_string()Tejun Heo2007-02-091-15/+2
| | | | | | | | | | There were several places where ATA ID strings are manually terminated and in some places possibly unterminated strings were passed to string functions which don't limit length like strstr(). This patch converts all of them over to ata_id_c_string(). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: straighten out ATA_ID_* constantsTejun Heo2007-02-091-3/+2
| | | | | | | | | | | | | | * Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency with other ATA_ID_* constants. * Kill ATA_SERNO_LEN * Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN. This change also makes ata_device_blacklisted() use proper length for fwrev. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: set_mode, Fix the FIXMEAlan2007-01-241-1/+3
| | | | | | | | When set_mode() changed ->set_mode didn't adapt. This makes the needed changes and removes the relevant FIXME case. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] libata: kill unnecessary sht->max_sectors initializationsTejun Heo2006-12-031-3/+0
| | | | | | | sht->max_sectors is overrided unconditionally in ->slave_configure. There's no reason to set it to any value. Signed-off-by: Tejun Heo <htejun@gmail.com>
* [PATCH] pata_it821x: Suspend/Resume supportAlan2006-12-011-2/+14
| | | | | | | | If you are using the noraid option then after a suspend/resume sequence we need to reset the card back out of raid mode again. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] libata: add missing sht->slave_destroyTejun Heo2006-11-291-0/+1
| | | | | | | | Many LLDs are missing sht->slave_destroy. The method is mandatory to support device warm unplugging (echo 1 > /sys/.../delete). Without it, libata might access released scsi device. Signed-off-by: Tejun Heo <htejun@gmail.com>
* [libata] PCI ID table cleanup in various driversJeff Garzik2006-09-281-7/+6
| | | | | | | | | | * Use PCI_VDEVICE() macro * const-ify pci_device_id table * standardize list terminator as "{ }" * convert spaces to tab in pci_driver struct (Alan-ism) * various minor whitespace cleanups Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Don't use old-EH ->eng_timeout() hook when not neededJeff Garzik2006-09-271-2/+2
| | | | | | | The PATA driver set got converted to the new error handling setup, but the old hooks were accidentally left in place. Now, removed. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata #pata-drivers] Trim trailing whitespace.Jeff Garzik2006-08-311-35/+35
|
* [libata] Add a bunch of PATA drivers.Jeff Garzik2006-08-291-0/+847
The vast majority of drivers and changes are from Alan Cox. Albert Lee contributed and maintains pata_pdc2027x. Adrian Bunk, Andrew Morton, and Tejun Heo contributed various minor fixes and updates. Signed-off-by: Jeff Garzik <jeff@garzik.org>
OpenPOWER on IntegriCloud