| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SGI UV systems print a message during boot:
UV: Found <num> blades
Due to packaging changes, the blade count is not accurate for
on the next generation of the platform. This patch corrects the
count.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120106191900.GA19772@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Skip cpus with apic-ids >= 255 in !x2apic_mode
x86, x2apic: Allow "nox2apic" to disable x2apic mode setup by BIOS
x86, x2apic: Fallback to xapic when BIOS doesn't setup interrupt-remapping
x86, acpi: Skip acpi x2apic entries if the x2apic feature is not present
x86, apic: Add probe() for apic_flat
x86: Simplify code by removing a !SMP #ifdefs from 'struct cpuinfo_x86'
x86: Convert per-cpu counter icr_read_retry_count into a member of irq_stat
x86: Add per-cpu stat counter for APIC ICR read tries
pci, x86/io-apic: Allow PCI_IOAPIC to be user configurable on x86
x86: Fix the !CONFIG_NUMA build of the new CPU ID fixup code support
x86: Add NumaChip support
x86: Add x86_init platform override to fix up NUMA core numbering
x86: Make flat_init_apic_ldr() available
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently "nox2apic" boot parameter was not enabling x2apic mode if the cpu,
kernel are all capable of enabling x2apic mode and the OS handover
happened in xapic mode.
However If the bios enabled x2apic prior to OS handover, using "nox2apic"
boot parameter had no effect.
If the boot cpu's apicid is < 255, enable "nox2apic" boot parameter to
disable the x2apic mode setup by the bios. This will enable the kernel to
fallback to xapic mode and bringup only the cpu's which has apic-id < 255.
-v2: fix patch error and two compiling warning
make disable_x2apic to be __init
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/CAE9FiQUeB-3uxJAMiHsz=uPWoFv5Hg1pVepz7aU6YtqOxMC-=Q@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On some of the recent Intel SNB platforms, by default bios is pre-enabling
x2apic mode in the cpu with out setting up interrupt-remapping.
This case was resulting in the kernel to panic as the cpu is already in
x2apic mode but the OS was not able to enable interrupt-remapping (which
is a pre-req for using x2apic capability).
On these platforms all the apic-ids are < 255 and the kernel can fallback to
xapic mode if the bios has not enabled interrupt-remapping (which is
mostly the case if the bios has not exported interrupt-remapping tables to the
OS).
Reported-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20111222014632.600418637@sbsiddha-desk.sc.intel.com
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently we start with the default apic_flat mode and switch to some other
apic model depending on the apic drivers acpi_madt_oem_check() routines and
later followed by the apic drivers probe() routines.
Once we selected non flat mode there was no case where we fall back to
flat mode again.
Upcoming changes allow bios-enabled x2apic mode to be disabled by the OS
if interrupt-remapping etc is not setup properly by the bios.
We now has a case for the apic to fall back to legacy flat mode during
apic driver probe() seqeuence. Add a simple flat_probe() which allows
the apic_flat mode to be the last fallback option.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20111222014632.484984298@sbsiddha-desk.sc.intel.com
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
LAPIC related statistics are grouped inside the per-cpu
structure irq_stat, so there is no need for icr_read_retry_count
to be a standalone per-cpu variable.
This patch moves icr_read_retry_count to where it belongs.
Suggested-y: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: Jörn Engel <joern@logfs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In the IPI delivery slow path (NMI delivery) we retry the ICR
read to check for delivery completion a limited number of times.
[ The reason for the limited retries is that some of the places
where it is used (cpu boot, kdump, etc) IPI delivery might not
succeed (due to a firmware bug or system crash, for example)
and in such a case it is better to give up and resume
execution of other code. ]
This patch adds a new entry to /proc/interrupts, RTR, which
tells user space the number of times we retried the ICR read in
the IPI delivery slow path.
This should give some insight into how well the APIC
message delivery hardware is working - if the counts are way
too large then we are hitting a (very-) slow path way too
often.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: Jörn Engel <joern@logfs.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/n/tip-vzsp20lo2xdzh5f70g0eis2s@git.kernel.org
[ extended the changelog ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Adds support for Numascale NumaChip large-SMP systems. It is
needed to enable the booting of more than ~168 cores.
v2:
- [Steffen] enumerate only accessible northbridges
- [Daniel] rediffed and validated against 3.1-rc10
v3:
- [Daniel] use x86_init core numbering override
- [Daniel] cleanups as per feedback
v4:
- [Daniel] use updated x86_cpuinit override
v5:
- drop disabling interrupts locally, as ISR write is atomic; drop delay
- added read-mostly annotations where appropriate
- require CONFIG_SMP, so drop conditional path
Workload tested on 96 cores/16 sockets.
Signed-off-by: Steffen Persvold <sp@numascale.com>
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Link: http://lkml.kernel.org/r/1323101246-2400-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allow flat_init_apic_ldr() to be used outside the compilation
unit for similar APIC implementations.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Cc: Steffen Persvold <sp@numascale.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Link: http://lkml.kernel.org/r/1323073238-32686-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Interrupts notify the idle exit state before calling irq_enter().
But the notifier code calls rcu_read_lock() and this is not
allowed while rcu is in an extended quiescent state. We need
to wait for irq_enter() -> rcu_idle_exit() to be called before
doing so otherwise this results in a grumpy RCU:
[ 0.099991] WARNING: at include/linux/rcupdate.h:194 __atomic_notifier_call_chain+0xd2/0x110()
[ 0.099991] Hardware name: AMD690VM-FMH
[ 0.099991] Modules linked in:
[ 0.099991] Pid: 0, comm: swapper Not tainted 3.0.0-rc6+ #255
[ 0.099991] Call Trace:
[ 0.099991] <IRQ> [<ffffffff81051c8a>] warn_slowpath_common+0x7a/0xb0
[ 0.099991] [<ffffffff81051cd5>] warn_slowpath_null+0x15/0x20
[ 0.099991] [<ffffffff817d6fa2>] __atomic_notifier_call_chain+0xd2/0x110
[ 0.099991] [<ffffffff817d6ff1>] atomic_notifier_call_chain+0x11/0x20
[ 0.099991] [<ffffffff81001873>] exit_idle+0x43/0x50
[ 0.099991] [<ffffffff81020439>] smp_apic_timer_interrupt+0x39/0xa0
[ 0.099991] [<ffffffff817da253>] apic_timer_interrupt+0x13/0x20
[ 0.099991] <EOI> [<ffffffff8100ae67>] ? default_idle+0xa7/0x350
[ 0.099991] [<ffffffff8100ae65>] ? default_idle+0xa5/0x350
[ 0.099991] [<ffffffff8100b19b>] amd_e400_idle+0x8b/0x110
[ 0.099991] [<ffffffff810cb01f>] ? rcu_enter_nohz+0x8f/0x160
[ 0.099991] [<ffffffff810019a0>] cpu_idle+0xb0/0x110
[ 0.099991] [<ffffffff817a7505>] rest_init+0xe5/0x140
[ 0.099991] [<ffffffff817a7468>] ? rest_init+0x48/0x140
[ 0.099991] [<ffffffff81cc5ca3>] start_kernel+0x3d1/0x3dc
[ 0.099991] [<ffffffff81cc5321>] x86_64_start_reservations+0x131/0x135
[ 0.099991] [<ffffffff81cc5412>] x86_64_start_kernel+0xed/0xf4
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|/
|
|
|
|
|
|
|
|
|
|
| |
There was a mixup when the SGI UV2 hub chip was sent to be
fabricated, and it ended up with the wrong part number in the
HRP_NODE_ID mmr. Future versions of the chip will (may) have the
correct part number. Change the UV infrastructure to recognize
both part numbers as valid IDs of a UV2 hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20111129210058.GA20452@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ioapic chip
with "apic=verbose" the print_IO_APIC() function tries to print
IRQ to pin mappings for every active irq. It assumes chip_data
is of type irq_cfg and may cause an oops if not.
As the print_IO_APIC() is called from a late_initcall other
chained irq chips may already be registered with custom
chip_data information, causing an oops. This is the case with
intel MID SoC devices with gpio demuxers registered as irq_chips.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
[ -v2: fixed build failure ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
|
|
|
|
|
|
|
| |
lapic timer calibration can be combined with tsc in platform
specific calibration functions. if such calibration result is
obtained early, we can skip the redundant calibration loops.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
|
|
|
|
|
|
| |
nr_legacy_irqs is set in probe_nr_irqs_gsi, we should not clear
it after that. Otherwise, the result is that MSI irqs will be
allocated from the wrong range for the systems without legacy
PIC.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|\
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: uv2: Workaround for UV2 Hub bug (system global address format)
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Standardize on CONFIG_SPARSE_IRQ=y
x86, ioapic: Clean up ioapic/apic_id usage
x86, ioapic: Factor out print_IO_APIC() to only print one io apic
x86, ioapic: Print out irte with right ioapic index
x86, ioapic: Split up setup_ioapic_entry()
x86, ioapic: Pass struct irq_attr * to setup_ioapic_irq()
apic, i386/bigsmp: Fix false warnings regarding logical APIC ID mismatches
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Sparseirq got introduced in v2.6.28 and Thomas did a huge cleanup
around v2.6.38 that eliminated basically all disadvantages
of it.
So we can remove non-sparseirq support now and simplify
our IRQ degrees of freedom a bit.
Suggested-and-acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4E95E21D.6090200@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
While looking at the code, apic_id sometime is referred to index
of ioapic, but sometime is used for phys apic id. and some even
use apic for real apic id. It is very confusing.
So try to limit apic_id or ioapic_id to be real apic id for
ioapic, and use ioapic_idx for ioapic index in the array.
-v2: Suggested by Ingo, use ioapic_idx consistently, instead of ioapic
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542DC.3090509@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
It is getting too big after the interrupt remaping entries debug
print out was added.
Original print_IO_APIC() becomes print_IO_APICs().
New print_IO_APIC() will only print one ioapic's registers
As a side-effect this clean-up also made checkpatch.pl happier.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542D3.5000008@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
While checking irte dump in dmesg, the print out is confusing
ioapic index with real io apic id:
IOAPIC[0]: Set routing entry (1-1 -> 0x31 -> IRQ 1 Mode:0
Active:0 Dest:1) IOAPIC[1]: Set IRTE entry (P:1 FPD:0 Dst_Mode:1
Redir_hint:1 Trig_Mode:0 Dlvry_Mode:1 Avail:0 Vector:31
Dest:00000001 SID:00FF SQ:0 SVT:1) IOAPIC[0]: Set routing entry
(1-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1) IOAPIC[1]: Set IRTE entry (P:1 FPD:0 Dst_Mode:1 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:1 Avail:0 Vector:30 Dest:00000001 SID:00FF SQ:0 SVT:1)
The system's first ioapic id is 1.
This commit:
| commit 3040db92ee1b6c5b6b6d73f8cdcad54c0da11563
| Author: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
| Date: Tue Jul 12 21:17:41 2011 +0000
|
| x86, ioapic: Print IRTE when IR is enabled
Confused apic_id with the ioapic ID - fix it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542C8.8040209@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Ingo pointed out that setup_ioapic_entry() is way too big now.
Split the intr-remap code out into setup_ir_ioapic_entry().
Also pass struct io_apic_irq_attr * instead of 5 parameters
in those two functions.
At last in setup_ir_ioapic_entry() we don't need to panic.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542BB.4070807@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Do not expand that struct, and just pass pointer to reduce the
number of parameters in related functions.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542B1.7050800@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
These warnings (generally one per CPU) are a result of
initializing x86_cpu_to_logical_apicid while apic_default is
still in use, but the check in setup_local_APIC() being done
when apic_bigsmp was already used as an override in
default_setup_apic_routing():
Overriding APIC driver with bigsmp
Enabling APIC mode: Physflat. Using 5 I/O APICs
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
...
CPU 1 irqstacks, hard=f1c9a000 soft=f1c9c000
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 9e000
Initializing CPU#1
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
setup_local_APIC+0x137/0x46b() Hardware name: ...
CPU1 logical APIC ID: 2 != 8
...
Fix this (for the time being, i.e. until
x86_32_early_logical_apicid() will get removed again, as Tejun
says ought to be possible) by overriding the previously stored
values at the point where the APIC driver gets overridden.
v2: Move this and the pre-existing override logic into
arch/x86/kernel/apic/bigsmp_32.c.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org> (2.6.39 and onwards)
Link: http://lkml.kernel.org/r/4E835D16020000780005844C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Just convert all the files that have an nmi handler to the new routines.
Most of it is straight forward conversion. A couple of places needed some
tweaking like kgdb which separates the debug notifier from the nmi handler
and mce removes a call to notify_die.
[Thanks to Ying for finding out the history behind that mce call
https://lkml.org/lkml/2010/5/27/114
And Boris responding that he would like to remove that call because of it
https://lkml.org/lkml/2011/9/21/163]
The things that get converted are the registeration/unregistration routines
and the nmi handler itself has its args changed along with code removal
to check which list it is on (most are on one NMI list except for kgdb
which has both an NMI routine and an NMI Unknown routine).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1317409584-23662-4-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Consolidate the io-apic EOI code in clear_IO_APIC_pin() and
eoi_ioapic_irq().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Rafael Wysocki <rjw@novell.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: lchiquitto@novell.com
Cc: jbeulich@novell.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110825190657.259696697@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For older IO-APIC's, we were clearing the remote-IRR by changing
the RTE trigger mode to edge and then back to level. We wanted
to mask the RTE during this process, so we were essentially
doing mask+edge and then to unmask+level.
As part of the commit ca64c47cecd0321b2e0dcbd7aaff44b68ce20654,
we moved this EOI process earlier where the IO-APIC RTE is
masked. So we were wrongly unmasking it in the eoi_ioapic_irq().
So change the remote-IRR clear sequence in eoi_ioapic_irq() to
mask + edge and then restore the previous RTE entry which will
restore the mask status as well as the level trigger.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Rafael Wysocki <rjw@novell.com>
Cc: lchiquitto@novell.com
Cc: jbeulich@novell.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110825190657.210286410@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In the kdump scenario mentioned below, we can have a case where
the device using level triggered interrupt will not generate any
interrupts in the kdump kernel.
1. IO-APIC sends a level triggered interrupt to the CPU's local APIC.
2. Kernel crashed before the CPU services this interrupt, leaving
the remote-IRR in the IO-APIC set.
3. kdump kernel boot sequence does clear_IO_APIC() as part of IO-APIC
initialization. But this fails to reset remote-IRR bit of the
IO-APIC RTE as the remote-IRR bit is read-only.
4. Device using that level triggered entry can't generate any
more interrupts because of the remote-IRR bit.
In clear_IO_APIC_pin(), check if the remote-IRR bit is set and if
so do an explicit attempt to clear it (by doing EOI write on
modern io-apic's and changing trigger mode to edge/level on
older io-apic's). Also before doing the explicit EOI to the
io-apic, ensure that the trigger mode is indeed set to level.
This will enable the explicit EOI to the io-apic to reset the
remote-IRR bit.
Tested-by: Leonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=701686
Cc: Rafael Wysocki <rjw@novell.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: jbeulich@novell.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110825190657.157502602@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Change the CONFIG_DMAR to CONFIG_INTEL_IOMMU to be consistent
with the other IOMMU options.
Rename the CONFIG_INTR_REMAP to CONFIG_IRQ_REMAP to match the
irq subsystem name.
And define the CONFIG_DMAR_TABLE for the common ACPI DMAR
routines shared by both CONFIG_INTEL_IOMMU and CONFIG_IRQ_REMAP.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: youquan.song@intel.com
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.558630224@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Define irq_remap_modify_chip_defaults() and remove the duplicate
code, cleanup the unnecessary ifdefs.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: youquan.song@intel.com
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.499225692@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
IRQ set affinity routine is same for the IO-APIC IRQ's aswell as
the MSI IRQ's in the presence of interrupt-remapping. This is
because we modify the interrupt-remapping table entry and
doesn't touch the IO-APIC RTE or the MSI entry.
So remove the ir_msi_set_affinity() and re-use the
ir_ioapic_set_affinity()
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: youquan.song@intel.com
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.452760446@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On the platforms which are x2apic and interrupt-remapping
capable, Linux kernel is enabling x2apic even if the BIOS
doesn't. This is to take advantage of the features that x2apic
brings in.
Some of the OEM platforms are running into issues because of
this, as their bios is not x2apic aware. For example, this was
resulting in interrupt migration issues on one of the platforms.
Also if the BIOS SMI handling uses APIC interface to send SMI's,
then the BIOS need to be aware of x2apic mode that OS has
enabled.
On some of these platforms, BIOS doesn't have a HW mechanism to
turnoff the x2apic feature to prevent OS from enabling it.
To resolve this mess, recent changes to the VT-d2 specification:
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
includes a mechanism that provides BIOS a way to request system
software to opt out of enabling x2apic mode.
Look at the x2apic optout flag in the DMAR tables before
enabling the x2apic mode in the platform. Also print a warning
that we have disabled x2apic based on the BIOS request.
Kernel boot parameter "intremap=no_x2apic_optout" can be used to
override the BIOS x2apic optout request.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.171766616@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Delete the 10 msec delay between the INIT and SIPI when starting
slave cpus. I can find no requirement for this delay. BIOS also
has similar code sequences without the delay.
Removing the delay reduces boot time by 40 sec. Every bit helps.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20110805140900.GA6774@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
'x86-kexec-for-linus', 'x86-platform-for-linus', 'x86-quirks-for-linus', 'x86-tsc-for-linus' and 'x86-smpboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-detect-hyper-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hyper: Change hypervisor detection order
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix DNA exception during check_fpu()
* 'x86-kexec-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kexec, x86: Fix incorrect jump back address if not preserving context
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, config: Introduce an INTEL_MID configuration
* 'x86-quirks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, quirks: Use pci_dev->revision
* 'x86-tsc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: tsc: Remove unneeded DMI-based blacklisting
* 'x86-smpboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, boot: Wait for boot cpu to show up if nr_cpus limit is about to hit
|
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
nr_cpus allows one to specify number of possible cpus in the system.
Current assumption seems to be that first cpu to show up is boot cpu
and this assumption will be broken in kdump scenario where we can be
booting on a non boot cpu with nr_cpus=1.
It might happen that first cpu we parse is not the cpu we boot on and
later we ignore boot cpu. Though code later seems to recognize this
anomaly and forcibly sets boot cpu in physical cpu map with following
warning.
if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) {
printk(KERN_WARNING
"weird, boot CPU (#%d) not listed by the BIOS.\n",
hard_smp_processor_id());
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
This patch waits for boot cpu to show up and starts ignoring the cpus
once we have hit (nr_cpus - 1) number of cpus. So effectively we are
reserving one slot out of nr_cpus for boot cpu explicitly.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20110708171926.GF2930@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ioapic: Print IR_IO_APIC_route_entry when IR is enabled
x86, ioapic: Print IRTE when IR is enabled
x86, x2apic: Preserve high 32-bits of IA32_APIC_BASE MSR
x86, ioapic: Also print Dest field
x86, ioapic: Format clean up for IOAPIC output
x86: print APIC data a little later during boot
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When IR (interrupt remapping) is enabled print_IO_APIC() displays output according
to legacy RTE (redirection table entry) definitons:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 00 1 0 0 0 0 0 0 00
01 00 0 0 0 0 0 0 0 01
02 00 0 0 0 0 0 0 0 02
03 00 1 0 0 0 0 0 0 03
04 00 1 0 0 0 0 0 0 04
05 00 1 0 0 0 0 0 0 05
06 00 1 0 0 0 0 0 0 06
...
The above output is as per Sec 3.2.4 of the IOAPIC datasheet:
82093AA I/O Advanced Programmable Interrupt Controller (IOAPIC):
http://download.intel.com/design/chipsets/datashts/29056601.pdf
Instead the output should display the fields as discussed in Sec 5.5.1
of the VT-d specification:
(Intel Virtualization Technology for Directed I/O:
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf)
After the fix:
NR Indx Fmt Mask Trig IRR Pol Stat Indx2 Zero Vect:
00 0000 0 1 0 0 0 0 0 0 00
01 000F 1 0 0 0 0 0 0 0 01
02 0001 1 0 0 0 0 0 0 0 02
03 0002 1 1 0 0 0 0 0 0 03
04 0011 1 1 0 0 0 0 0 0 04
05 0004 1 1 0 0 0 0 0 0 05
06 0005 1 1 0 0 0 0 0 0 06
...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110712211658.2939.93123.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When "apic=debug" is used as a boot parameter, Linux prints the IOAPIC routing
entries in "dmesg". Below is output from IOAPIC whose apic_id is 8:
# dmesg | grep "routing entry"
IOAPIC[8]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
IOAPIC[8]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
IOAPIC[8]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0)
...
Similarly, when IR (interrupt remapping) is enabled, and the IRTE
(interrupt remapping table entry) is set up we should display it.
After the fix:
# dmesg | grep IRTE
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:31 Dest:00000000 SID:00F1 SQ:0 SVT:1)
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:30 Dest:00000000 SID:00F1 SQ:0 SVT:1)
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:33 Dest:00000000 SID:00F1 SQ:0 SVT:1)
...
The IRTE is defined in Sec 9.5 of the Intel VT-d Specification.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110712211704.2939.71291.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If there's no special reason to zero-out the "high" 32-bits of the IA32_APIC_BASE
MSR, let's preserve it.
The x2APIC Specification doesn't explicitly state any such requirement. (Sec 2.2
in: http://www.intel.com/Assets/PDF/manual/318148.pdf).
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110712055831.2498.78521.sendpatchset@nchumbalkar.americas.cpqcorp.net
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The code in setup_ioapic_irq() determines the Destination Field,
so why not also include it in the debug printk output that gets
displayed when the boot parameter "apic=debug" is used.
Before the change, "dmesg" will show:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) ...
After the change, you will see:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) ...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184603.2734.91071.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When IOAPIC data is displayed in "dmesg" with the help of the
boot parameter "apic=debug" certain values are not formatted
correctly wrt their size.
In the "dmesg" snippet below, note that the output for "max
redirection entries", and "IO APIC version" which are each
defined to be just 8-bits long are displayed as 2 bytes in
length. Similarly, "Dst" under the "IRQ redirection table"
should only be 8-bits long.
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 000 1 0 0 0 0 0 0 00
01 000 0 0 0 0 0 0 0 31
02 000 0 0 0 0 0 0 0 30
03 000 1 0 0 0 0 0 0 33
...
...
Do some formatting clean up, so you will see output like below:
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 17
....... : PRQ implemented: 0
....... : IO APIC version: 20
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 00 1 0 0 0 0 0 0 00
01 00 0 0 0 0 0 0 0 31
02 00 0 0 0 0 0 0 0 30
03 00 1 0 0 0 0 0 0 33
...
...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184557.2734.61830.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To view IOAPIC data you could boot with "apic=debug".
When booting in such a way then the kernel will dump the
IO-APIC's registers, for example:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 000 1 0 0 0 0 0 0 00
01 000 0 0 0 0 0 0 0 31
02 000 0 0 0 0 0 0 0 30
03 000 0 0 0 0 0 0 0 33
04 000 0 0 0 0 0 0 0 34
05 000 0 0 0 0 0 0 0 35
06 000 0 0 0 0 0 0 0 36
07 000 0 0 0 0 0 0 0 37
08 000 0 0 0 0 0 0 0 38
09 000 0 1 0 0 0 0 0 39
0a 000 0 0 0 0 0 0 0 3A
0b 000 0 0 0 0 0 0 0 3B
0c 000 0 0 0 0 0 0 0 3C
0d 000 0 0 0 0 0 0 0 3D
0e 000 0 0 0 0 0 0 0 3E
0f 000 0 0 0 0 0 0 0 3F
10 000 1 0 0 0 0 0 0 00
11 000 1 0 0 0 0 0 0 00
12 000 1 0 0 0 0 0 0 00
13 000 1 0 0 0 0 0 0 00
14 000 1 0 0 0 0 0 0 00
15 000 1 0 0 0 0 0 0 00
16 000 1 0 0 0 0 0 0 00
17 000 1 0 0 0 0 0 0 00
Delaying the call to print_ICs() gives better results:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 000 1 0 0 0 0 0 0 00
01 000 0 0 0 0 0 0 0 31
02 000 0 0 0 0 0 0 0 30
03 000 1 0 0 0 0 0 0 33
04 000 1 0 0 0 0 0 0 34
05 000 1 0 0 0 0 0 0 35
06 000 1 0 0 0 0 0 0 36
07 000 1 0 0 0 0 0 0 37
08 000 0 0 0 0 0 0 0 38
09 000 0 1 0 0 0 0 0 39
0a 000 1 0 0 0 0 0 0 3A
0b 000 1 0 0 0 0 0 0 3B
0c 000 0 0 0 0 0 0 0 3C
0d 000 1 0 0 0 0 0 0 3D
0e 000 1 0 0 0 0 0 0 3E
0f 000 1 0 0 0 0 0 0 3F
10 000 1 1 0 1 0 0 0 29
11 000 1 0 0 0 0 0 0 00
12 000 1 0 0 0 0 0 0 00
13 000 1 0 0 0 0 0 0 00
14 000 0 1 0 1 0 0 0 51
15 000 1 0 0 0 0 0 0 00
16 000 0 1 0 1 0 0 0 61
17 000 0 1 0 1 0 0 0 59
Notice that the entries beyond interrupt input signal 0x0f also
get populated and arent just the hw-initialization default of
all zeroes.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708083555.2598.42216.sendpatchset@nchumbalkar.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|\ \ \
| |/ /
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There are multiple declarations of global_clock_event in header files
specific to particular clock event implementations. Consolidate them
in <asm/time.h> and make sure all users include that header.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Venkatesh Pallipadi (Venki) <venki@google.com>
Link: http://lkml.kernel.org/r/20110601180610.762763451@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180610.054254048@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/arm/mach-footbridge/isa-timer.c | 2 +-
arch/mips/cobalt/time.c | 2 +-
arch/mips/jazz/irq.c | 2 +-
arch/mips/kernel/i8253.c | 2 +-
arch/mips/mti-malta/malta-time.c | 2 +-
arch/mips/sgi-ip22/ip22-time.c | 2 +-
arch/mips/sni/time.c | 2 +-
arch/x86/kernel/apic/apic.c | 2 +-
arch/x86/kernel/apm_32.c | 2 +-
arch/x86/kernel/hpet.c | 2 +-
arch/x86/kernel/i8253.c | 2 +-
arch/x86/kernel/time.c | 2 +-
drivers/block/hd.c | 2 +-
drivers/clocksource/i8253.c | 2 +-
drivers/input/gameport/gameport.c | 2 +-
drivers/input/joystick/analog.c | 2 +-
drivers/input/misc/pcspkr.c | 2 +-
include/linux/i8253.h | 11 +++++++++++
sound/drivers/pcsp/pcsp.h | 2 +-
19 files changed, 29 insertions(+), 18 deletions(-)
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Compare only lower 32 bits of framebuffer map offsets
drm/i915: Don't leak in i915_gem_shmem_pread_slow()
drm/radeon/kms: do bounds checking for 3D_LOAD_VBPNTR and bump array limit
drm/radeon/kms: fix mac g5 quirk
x86/uv/x2apic: update for change in pci bridge handling.
alpha, drm: Remove obsolete Alpha support in MGA DRM code
alpha/drm: Cleanup Alpha support in DRM generic code
savage: remove unnecessary if statement
drm/radeon: fix GUI idle IH debug statements
drm/radeon/kms: check modes against max pixel clock
drm: fix fbs in DRM_IOCTL_MODE_GETRESOURCES ioctl
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When I added 3448a19da479b6bd1e28e2a2be9fa16c6a6feb39
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|\ \
| |/
|/|
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile into perf/urgent
|