| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
| |
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This board is SH7723 base board.
This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.
This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
| |
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
Presently the --fdpic specifier and the --isa matching clash when
building with FDPIC toolchains. As we have no interest in building the
kernel with --fdpic in the first place, always try to add in -mno-fdpic
to the default flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
| |
SH_MPC1211 has been marked as BROKEN for some time.
Unless someone is working on reviving it now, I'd therefore suggest this
patch to remove it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
| |
Add support for Solution Engine SH7721 board(MS7721RP01).
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When building the kernel without passing the O= command line parameter
there's no point to use absolute paths for them.
Usually relative paths are preferred because they survive directory
moves, work across networked file systems and chrooted environments.
Absolute paths are still used if an output directory is given.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds basic support for the Migo-R board.
Only simple stuff provided by the cpu specific sh7722 code is in place now,
like serial console port, timers and usb gadget. There is also partial support
for the smc91c111 ethernet controller - unfortunately some driver header file
also needs patching (not included here) to make the driver get IRQ sense
information from the platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
| |
Add support for Renesas Technology Europe SDK7780 board.
Signed-off-by: Nicholas Beck <nbeck@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
| |
Some of Sam's new work in the kbuild queue depend on ## concatenation
within the linker script, which doesn't work when -traditional is
enabled. -traditional is a legacy remnant anyways, and we no longer
require it for anything, so kill it off completely.
Noted-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
This patch removes redundant irq handling code together with unused
consistent alloc code. R2D uart setup code is changed to use
sm501-regs.h and unused header files are removed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
| |
Signed-off-by: Kieran Bingham <kbingham@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
| |
This was using the absolute path, which was confusing the make target.
Switch it to just 'zImage', as per powerpc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
| |
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
| |
Adds the ISA tuning and a lib64 rule.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
| |
Starting with binutils somewhere around 2.17.50.14 the vmlinux file
contains a ".note.gnu.build-id" section which doesn't get removed when
the zImage is built; resulting in a 2GB intermediate file and a broken
zImage.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds support for the SH7720 (SH3-DSP) based Magic Panel R2
board.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch replaces all instances of CONFIG_VOYAGERGX with
CONFIG_MFD_SM501. While at it we make sure the r2d code compiles
both with and without SM501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|/
|
|
|
|
|
|
| |
This adds initial support for the SH-X3 prototype board.
Only simple logic for the IRQ controller and the heartbeat driver
for now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Older versions of binutils do not support -Wa,-isa= tuning, which is
something we rely on for enabling DSP opcode support on the newer
parts. SH3-DSP parts can still be handled with -Wa,-dsp even if the
newer parts require the newer versions of binutils for supporting the
new opcodes.
This was broken in -rc1 when the SH4AL-DSP support was being reworked,
and is needed to get SH3-DSP working with older toolchains again.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
| |
Kill off the hd64461 io.c, as all of the hd64461 users are now
using the generic I/O routines.
[ hd64461/ moved to hd64461.c by Paul ]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Older compilers don't support the -m4a{,nofpu} flags, which has the
side-effect of allowing FP operations to be emitted. Switch this to
incremental tuning, so we at least have -m4-nofpu as a fallback for
the gcc3 toolchains.
Without this, certain modules emit references to __udivsi3_i4 and
__sdivsi3_i4.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
We already hand off the proper ISA variant with the dsp specifier
appended, so we don't need to explicitly set -dsp. This causes some
confusion with certain toolchains that are restricted to -dsp family
opcodes artificially.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
| |
These weren't being cleaned up, so add them to the CLEAN_FILES.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
| |
This was added during 2.5.x, but was never moved along. This
can easily be resurrected if someone has one they wish to work
with, but it's not worth keeping around in its current form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
Some compilers don't support the explicit CPU tuning, while binutils
is still able to handle the special subtype-specific opcodes. Make
the CFLAG optional, falling back on the compiler default if nothing
better exists.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This kills off the BareCPU board as a "special" machvec, rather,
we leave this as a default for when no other vector is available,
or when we want to use it in combination with other vectors for
testing with generic ops. As sh_mv is copied out anyways (or
overloaded when an alternate vector is explicitly selected), this
doesn't consume any additional memory.
The generic machvec can be forcibly selected with sh_mv=generic,
or by not having any other boards enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
This tidies up the build rules and permits multiple boards to be
linked in to the same kernel. The earlier Kconfig work ensures that
the CPU configuration is consistent across the boards, as this is
the only thing that we can't do dynamically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
| |
Make my version of gcc happy.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
| |
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
| |
This adds support for the SH7780-based Solution Engine reference board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
|
|
|
| |
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
| |
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
| |
Neither of these have had any maintenance in years, and there's
no interest in keeping them straggling along. These have already
been slated for removal some time, so finally just get rid of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
|
|
|
|
| |
-m2 doesn't end up working particularly well when we've got a constrained
toolchain target. Switch to the same semantics used by SH-4A to attempt
to get it right. Spotted by Alex Song <songqf9@yahoo.ca>.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|