summaryrefslogtreecommitdiffstats
path: root/arch/mips/rb532
Commit message (Collapse)AuthorAgeFilesLines
* Input: add driver for S1 button of rb532Phil Sutter2009-03-091-18/+1
| | | | | | | | | | | | | | | | | | | Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* MIPS: RB532: Export rb532_gpio_set_func()Phil Sutter2009-01-301-2/+3
| | | | | | | | | | This kernel symbol provides a way for drivers to switch on alternate function for a certain GPIO pin. Turning it off is done implicitly when changing the GPIO direction, as that would be fixed when using the given pin als alternate function. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Simplify dev3 initPhil Sutter2009-01-301-12/+2
| | | | | | | | | | | | As rb532_dev3_ctl_res is not used by any platform device, it can be dropped when not used for holding the physical address of the device 3 controller. Also a size of one byte should suffice when ioremapping the physical address mentioned above, as only a single byte is being read from and written to it. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Remove {get,set}_434_reg()Phil Sutter2009-01-301-27/+0
| | | | | | | | These kernel symbols are unused. Also, since dev3 init has been moved to devices.c, set_434_reg() breaks compiling as it uses dev3. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Move dev3 init code to devices.cPhil Sutter2009-01-302-39/+39
| | | | | | | | | This code doesn't belong to gpio.c, as it's completely unrelated to GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more adequate place. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Fix set_latch_u5()Phil Sutter2009-01-301-1/+1
| | | | | | | | | The data to be written is just a byte, so use writeb instead of writel. Also, dev3.base contains the address, not the data so referencing here is wrong. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Fix init of rb532_dev3_ctl_resPhil Sutter2009-01-301-2/+3
| | | | | | | | This register just contains the address of the actual resource, so initialisation has to be the same as cf_slot0_res and nand_slot0_res. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Use driver_data instead of platform_dataPhil Sutter2009-01-301-1/+1
| | | | | | | | | As the korina ethernet driver uses platform_get_drvdata() to extract the driver specific data from the platform device, driver_data has to be used here. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Detect uart type, add platform devicePhil Sutter2009-01-302-1/+27
| | | | | | | | | Auto-detection works just fine, so use it instead of specifying the type manually. Also define a platform device for the uart, as suggested by David Daney. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: remove useless CF GPIO initialisationPhil Sutter2009-01-301-6/+0
| | | | | | | | | | | | As the pata-rb532-cf driver calls gpio_direction_input(), the calls to rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since the alternate function is automatically being disabled when changing the GPIO pin direction. The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being done by the IRQ initialisation of pata-rb532-cf. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Auto disable GPIO alternate functionPhil Sutter2009-01-301-4/+4
| | | | | | | | | | When a driver calls gpio_set_direction_{input,output}(), it obviously doesn't want the alternate function for that pin to be active (as the direction would not matter in that case). This patch ensures alternate function is disabled when the direction is being changed. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Add set_type() function to IRQ struct.Phil Sutter2009-01-301-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources; add defines to make this clear when addressing them later in code. The mapped GPIOs support triggering on either level high or low. To achieve this, the set_type() function calls rb532_gpio_set_ilevel() for interrupts of the above mentioned group. As there is no way to alter the triggering characteristics of the other interrupts, accept level triggering on status high only. (This is just a guess; but as the system boots fine and interrupt-driven devices (e.g. serial console) work with no implications, it seems to be right.) To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the interrupt status bit of the corresponding GPIO pin). This is done inside rb532_disable_irq(). After applying these changes I could undo most of my former "fixes" to pata-rb532-cf. Particularly all interrupt handling can be done generically via set_irq_type() as it was before. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Fix bit swapping in rb532_set_bit()Phil Sutter2009-01-301-4/+2
| | | | | | | | | | The algorithm works unconditionally. If bitval is one, the first line is a no op and the second line sets the bit at offset position. Vice versa, if bitval is zero, the first line clears the bit at offset position and the second line is a no op. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Provide functions for gpio configurationPhil Sutter2008-11-201-120/+73
| | | | | | | | | | As gpiolib doesn't support pin multiplexing, it provides no way to access the GPIOFUNC register. Also there is no support for setting interrupt status and level. These functions provide access to them and are needed by the CompactFlash driver. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: GPIO register offsets are relative to GPIOBASEFlorian Fainelli2008-11-201-1/+1
| | | | | | | | | | | | | This patch fixes the wrong use of GPIO register offsets in devices.c. To avoid further problems, use gpio_get_value to return the NAND status instead of our own expanded code. Also define the zero offset of the alternate function register to allow consistent access. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Disable the right devicePhil Sutter2008-10-271-1/+1
| | | | | Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Set gpio interrupt status and level for CompactFlashFlorian Fainelli2008-10-271-0/+4
| | | | | | | | This patch sets the correct interrupt status and level in order to get the CompactFlash adapter working. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Kill unused <asm/debug.h> inclusionsShinya Kuribayashi2008-10-151-1/+0
| | | | | Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Convert to GPIO libFlorian Fainelli2008-10-111-67/+161
| | | | | | | | This patch converts the rb532 code to use gpio library and register its gpio chip. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Cleanup the headers againFlorian Fainelli2008-10-113-6/+6
| | | | | | | | | This patch cleans up headers and regroups informations to where they should reside. While moving, try to have a consistant naming for defines. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Remove obsolute reference to setup_serial_portFlorian Fainelli2008-10-111-2/+0
| | | | | | | | We are no longer using setup_serial_port. So just remove it from the prom code. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Fix id usage in platform devicesFlorian Fainelli2008-10-111-3/+3
| | | | | | | | When there is only platform device of the same type, id = -1 should be used, fix this. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: replace raw volatile read with a readlFlorian Fainelli2008-10-111-1/+1
| | | | | | | | This patch replaces a raw read using volatiles with a readl. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Remove gpio bootup stateFlorian Fainelli2008-10-111-10/+0
| | | | | | | | | | We are no longer using gpio bootup state, so do not export it and do not parse the kernel command line tag for it. Instead we provide gpio-keys for the button the gpio bootup state was checking. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Use physical addresses for gpio and device controller registersFlorian Fainelli2008-10-111-4/+4
| | | | | | | | | This patch fixes the misuse of virtual addresses for the GPIO and third device controller which would lead to problems while accessing ioremap'd registers. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: RB532: Cleanup and group definitions to their right placesFlorian Fainelli2008-10-111-14/+2
| | | | | | | | This patch moves GPIO related definitions to gpio.h and IRQ related to irq.h Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* [MIPS] RB532: Do not define registers that are already definedFlorian Fainelli2008-08-261-13/+3
| | | | | | | | Use the register definitions of the MPMC controller from mach-rc32434/rb.h instead of redefining them. Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* [MIPS] RB532: Flags are unsigned longAdrian Bunk2008-07-302-4/+5
| | | | | | | | | | | | | | | | | | | | A recent generic change now catches such bugs: <-- snip --> ... CC arch/mips/rb532/time.o cc1: warnings being treated as errors /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c: In function 'plat_time_init': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:55: error: comparison of distinct pointer types lacks a cast /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:66: error: comparison of distinct pointer types lacks a cast make[2]: *** [arch/mips/rb532/time.o] Error 1 <-- snip --> Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* [MIPS] Routerboard 532: Support for base systemRalf Baechle2008-07-208-0/+1124
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
OpenPOWER on IntegriCloud