summaryrefslogtreecommitdiffstats
path: root/arch/mips/alchemy/common
Commit message (Collapse)AuthorAgeFilesLines
* MIPS: Au1000: convert to using gpiolibFlorian Fainelli2009-03-301-75/+128
| | | | | | | This patch converts the GPIO board code to use gpiolib. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0Roel Kluin2009-02-271-3/+3
| | | | | | | | | With a postfix decrement t reaches -1 rather than 0, so the fall-back will not occur. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: mano@roarinelk.homelinux.net Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: time.c build fixManuel Lauss2009-01-301-1/+1
| | | | | | | In Linus' current -git the cpumask member is now a pointer. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: new userspace suspend interface for development boards.Manuel Lauss2009-01-112-353/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace the current sysctl-based suspend interface with a new sysfs- based one which also uses the Linux-2.6 suspend model. To configure wakeup sources, a subtree for the demoboards is created under /sys/power/db1x: sys/ `-- power `-- db1x |-- gpio0 |-- gpio1 |-- gpio2 |-- gpio3 |-- gpio4 |-- gpio5 |-- gpio6 |-- gpio7 |-- timer |-- timer_timeout |-- wakemsk `-- wakesrc The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2 bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1' enables a wakesource, 0 disables it. The 'timer_timeout' node holds the timeout in seconds after which the TOYMATCH2 event should wake the system. The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex), the 'wakemsk' node can be used to get/set the wakeup mask directly. For example, to have the timer wake the system after 10 seconds of sleep, the following must be done in userspace: echo 10 > /sys/power/db1x/timer_timeout echo 1 > /sys/power/db1x/timer echo mem > /sys/power/sleep This patch also removes the homebrew CPU frequency switching code. I don't understand how it could have ever worked reliably; it does not communicate the clock changes to peripheral devices other than uarts. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> create mode 100644 arch/mips/alchemy/devboards/pm.c
* MIPS: Alchemy: dbdma suspend/resume support.Manuel Lauss2009-01-112-0/+76
| | | | | | | Implement suspend/resume for DBDMA controller and its channels. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: Fix up PM code on Au1550/Au1200Manuel Lauss2009-01-113-167/+219
| | | | | | | | | | | | Au1550/Au1200 have a different memory controller which requires additi- onal code to properly put memory to sleep (code taken from AMD/RMI's Linux-2.6.11 source package). Also fix up the remaining pm-related paths to compile on Au1200/Au1550 platforms. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: move calc_clock function.Manuel Lauss2009-01-113-54/+63
| | | | | | | | | | Now that nothing in time.c depends on calc_clock, it can be moved to clocks.c where it belongs. While at it, give it a better non-generic name and call it as soon as possible in plat_mem_init. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: RTC counter clocksource / clockevent support.Manuel Lauss2009-01-113-177/+137
| | | | | | | | | | | | Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent device. As a nice side effect, this also enables use of the 'wait' instruction for runtime idle power savings. If the counters aren't enabled/working properly, fall back on the cp0 counter clock code. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: remove cpu_table.Manuel Lauss2009-01-114-80/+4
| | | | | | | | | | | | | | | | Remove the cpu_table: - move detection of whether c0_config[OD] is read-only and should be set to fix various chip errata to au1000 headers. - move detection of write-only sys_cpupll to au1000 headers. - remove the BCLK switching code: Activation of this features should be left to the boards using the chips since it also affects external devices tied to BCLK, and only the board designers know whether it is safe to enable. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/cputable.c
* MIPS: Alchemy: remove get/set_au1x00_lcd_clock().Manuel Lauss2009-01-112-32/+0
| | | | | | | There are no in-tree users, so remove them. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: update core interrupt code.Manuel Lauss2009-01-114-571/+427
| | | | | | | | | | | | | | | | | | | | | | | This patch attempts to modernize core Alchemy interrupt handling code. - add irq_chips for irq controllers instead of irq type, - add a set_type() hook to change irq trigger type during runtime, - add a set_wake() hook to control GPIO0..7 based wakeup, - use linux' IRQF_TRIGGER_ constants instead of homebrew ones, - enable GENERIC_HARDIRQS_NO__DO_IRQ. - simplify plat_irq_dispatch - merge au1xxx_irqmap into irq.c file, the only place where its contents are referenced. - board_init_irq() is now mandatory for every board; use it to register the remaining (gpio-based) interrupt sources; update all boards accordingly. Run-tested on Db1200 and other Au1200 based platforms. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
* MIPS: Alchemy: move commandline mangling out of common codeManuel Lauss2009-01-111-30/+4
| | | | | | | | | | | Not every alchemy-based board might want these options forced on it, and most of this stuff seems to be intended for devboard code anyway. Remove commandline mangling code out of common chip code and instead add relevant sections to all in-tree boards to not change existing behaviour. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: Wire up SD controller on DB/PB1200 boards.Manuel Lauss2008-10-271-24/+74
| | | | | | | | Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD controllers for them. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* MIPS: Alchemy: rename directoryRalf Baechle2008-10-1117-0/+4195
It's more than the au1000 these days. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
OpenPOWER on IntegriCloud