summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-vexpress
Commit message (Collapse)AuthorAgeFilesLines
* ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power downLorenzo Pieralisi2013-09-301-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the TC2 testchip, when all CPUs in a cluster enter standbywfi and commit a power down request, the power controller will wait for standbywfil2 coming from L2 cache controller to shut the cluster down. By the time all CPUs in a cluster commit a power down request and enter wfi, the power controller cannot backtrack, or put it another way, a CPU must not be allowed to complete execution independently of the power controller, the only way for it to resume properly must be upon wake-up IRQ pending and subsequent reset triggered from the power controller. Current MCPM back-end for TC2 disables the GIC CPU IF only when power down is committed through the tc2_pm_suspend() method, that makes sense since a suspended CPU is still online and can receive interrupts whereas a hotplugged CPU, since it is offline, migrated all IRQs and shutdown the per-CPU peripherals, hence their PPIs. The flaw with this reasoning is the following. If all CPUs in a clusters are entering a power down state either through CPU idle or CPU hotplug, when the last man successfully completes the MCPM power down sequence (and executes wfi), power controller waits for L2 wfi signal to quiesce the cluster and shut it down. If, when all CPUs are sitting in wfi, an online CPU hotplugs back in one of the CPUs in the cluster being shutdown, that CPU receives an IPI that causes wfi to complete (since tc2_pm_down() method does not disable the GIC CPU IF in that case - CPU being hotplugged out, not idle) and the power controller will never see the stanbywfil2 signal coming from L2 that is required for shutdown to happen and the system deadlocks. Further to this issue, kexec hotplugs secondary CPUs out during kernel reload/restart. Because kexec may (deliberately) trash the old kernel text, it is not OK for CPUs to follow the MCPM soft reboot path, since instructions after the WFI may have been replaced by kexec. If tc2_pm_down() does not disable the GIC cpu interface, there is a race between CPU powerdown in the old kernel and the IPI from the new kernel that triggers secondary boot, particularly if the powerdown is slow (due to L2 cache cleaning for example). If the new kernel wins the race, the affected CPU(s) will not really be reset and may execute garbage after the WFI. The only solution to this problem consists in disabling the GIC CPU IF on a CPU committed to power down regardless of the power down entry method (CPU hotplug or CPU idle). This way, CPU wake-up is under power controller control, which prevents unexpected wfi exit caused by a pending IRQ. This patch moves the GIC CPU IF disable call in the TC2 MCPM implementation from the tc2_pm_suspend() method to the tc2_pm_down() method to fix the mentioned race condition(s). Reviewed-by: Dave Martin <Dave.Martin@arm.com> Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec) Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
* ARM: vexpress: allow dcscb and tc2_pm in a combined ARMv6+v7 buildNicolas Pitre2013-09-091-0/+2
| | | | | | | | | | | | | | | | | This fixes the following build error: /tmp/cce439dZ.s: Assembler messages: /tmp/cce439dZ.s:506: Error: selected processor does not support ARM mode `isb ' /tmp/cce439dZ.s:512: Error: selected processor does not support ARM mode `isb ' /tmp/cce439dZ.s:513: Error: selected processor does not support ARM mode `dsb ' /tmp/cce439dZ.s:583: Error: selected processor does not support ARM mode `isb ' /tmp/cce439dZ.s:589: Error: selected processor does not support ARM mode `isb ' /tmp/cce439dZ.s:590: Error: selected processor does not support ARM mode `dsb ' Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Nicolas Pitre <nico@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
* Merge tag 'drivers-for-linus' of ↵Linus Torvalds2013-09-091-0/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver update from Kevin Hilman: "This contains the ARM SoC related driver updates for v3.12. The only thing this cycle are core PM updates and CPUidle support for ARM's TC2 big.LITTLE development platform" * tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: cpuidle: big.LITTLE: vexpress-TC2 CPU idle driver ARM: vexpress: tc2: disable GIC CPU IF in tc2_pm_suspend drivers: irq-chip: irq-gic: introduce gic_cpu_if_down()
| * ARM: vexpress: tc2: disable GIC CPU IF in tc2_pm_suspendLorenzo Pieralisi2013-08-281-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To prevent cores from exiting wfi when they are about to be shut down the GIC CPU IF must be disabled so that the GIC CPU IF IRQ output line is not asserted to the cores. wfi completion must be prevented since, in absence of coordinating HW logic, if the power controller receives a standbywfi signal but in the meantime the processor restarts executing owing to a pending IRQ, the core might be reset when running in a non-quiescent state (eg with pending load/store transactions) Raw GIC distributor IRQ signals are routed to the power controller, that is capable of taking core out of reset on pending IRQs even if their GIC CPU IF is disabled, thus keeping the normal wfi behaviour. GIC CPU IF is restored upon CPU wake-up by the respective MCPM API consumers (ie CPU idle driver and suspend to RAM thread). Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
* | Merge tag 'soc-for-linus' of ↵Linus Torvalds2013-09-066-21/+610
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform changes from Olof Johansson: "This branch contains mostly additions and changes to platform enablement and SoC-level drivers. Since there's sometimes a dependency on device-tree changes, there's also a fair amount of those in this branch. Pieces worth mentioning are: - Mbus driver for Marvell platforms, allowing kernel configuration and resource allocation of on-chip peripherals. - Enablement of the mbus infrastructure from Marvell PCI-e drivers. - Preparation of MSI support for Marvell platforms. - Addition of new PCI-e host controller driver for Tegra platforms - Some churn caused by sharing of macro names between i.MX 6Q and 6DL platforms in the device tree sources and header files. - Various suspend/PM updates for Tegra, including LP1 support. - Versatile Express support for MCPM, part of big little support. - Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7) - OMAP2+ support for DRA7, a new Cortex-A15-based SoC. The code that touches other architectures are patches moving MSI arch-specific functions over to weak symbols and removal of ARCH_SUPPORTS_MSI, acked by PCI maintainers" * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits) tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list ARM: dts: vf610-twr: enable i2c0 device ARM: dts: i.MX51: Add one more I2C2 pinmux entry ARM: dts: i.MX51: Move pins configuration under "iomuxc" label ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX ARM: dts: i.MX27: Disable AUDMUX in the template ARM: dts: wandboard: Add support for SDIO bcm4329 ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template ARM: dts: imx53-qsb: Make USBH1 functional ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module ARM: dts: imx6qdl-sabresd: Add touchscreen support ARM: imx: add ocram clock for imx53 ARM: dts: imx: ocram size is different between imx6q and imx6dl ARM: dts: imx27-phytec-phycore-som: Fix regulator settings ARM: dts: i.MX27: Remove clock name from CPU node ...
| * | ARM: vexpress/MCPM: fix cache disable sequence when CONFIG_FRAME_POINTER=yNicolas Pitre2013-08-142-8/+24
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | If CONFIG_FRAME_POINTER=y we get the following error: arch/arm/mach-vexpress/tc2_pm.c: In function 'tc2_pm_down': arch/arm/mach-vexpress/tc2_pm.c:200:1: error: fp cannot be used in asm here Let's fix that by explicitly preserving r11 on the stack and removing it from the clobber list. Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
| * ARM: vexpress/TC2: implement PM suspend methodNicolas Pitre2013-08-071-1/+18
| | | | | | | | | | | | | | | | | | | | | | Similar to power_down(), except that for a suspend, the firmware mailbox address has to be set prior entering low power mode. The residency argument is not used yet, so the last man always shuts down the cluster for now. Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * ARM: vexpress/TC2: basic PM supportNicolas Pitre2013-08-073-0/+336
| | | | | | | | | | | | | | | | | | | | | | | | This is the MCPM backend for the Virtual Express A15x2 A7x3 CoreTile aka TC2. This provides cluster management for SMP secondary boot and CPU hotplug. Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Pawel Moll <pawel.moll@arm.com> Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> [PM: made it drive SCC registers directly and provide base for SPC] Signed-off-by: Pawel Moll <pawel.moll@arm.com>
| * ARM: vexpress/TC2: add Serial Power Controller (SPC) supportLorenzo Pieralisi2013-08-072-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TC2 versatile express core tile integrates a logic block that provides the interface between the dual cluster test-chip and the M3 microcontroller that carries out power management. The logic block, called Serial Power Controller (SPC), contains several memory mapped registers to control among other things low-power states, wake-up irqs and per-CPU jump addresses registers. This patch provides a driver that enables run-time control of features implemented by the SPC power management control logic with an API to be used by different subsystem drivers on top. The SPC control logic is required to be programmed very early in the boot process to reset secondary CPUs on the TC2 testchip, set-up jump addresses and wake-up IRQs for power management. Hence, waiting for core changes to be made in the device core code to enable early registration of platform devices, the driver puts in place an early init scheme that allows kernel drivers to initialize the SPC driver directly from the components requiring it, if their initialization routine is called before this driver init function during the boot process. Device tree bindings documentation for the SPC component is also provided. Cc: Olof Johansson <olof@lixom.net> Cc: Amit Kucheria <amit.kucheria@linaro.org> Cc: Jon Medhurst <tixy@linaro.org> Signed-off-by: Achin Gupta <achin.gupta@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com> Acked-by: Pawel Moll <pawel.moll@arm.com> [ np: moved from drivers/mfd/ to drivers/platform/vexpress/ ] Signed-off-by: Nicolas Pitre <nico@linaro.org> [ PM: moved again to arch/arm/mach-vexpress, requested by Olof ] [ PM: removed useless printk, from Olof ] [ PM: made the driver SPC-only ] Signed-off-by: Pawel Moll <pawel.moll@arm.com>
| * ARM: vexpress/dcscb: fix cache disabling sequencesNicolas Pitre2013-07-221-21/+37
| | | | | | | | | | | | | | | | | | Unlike real A15/A7's, the RTSM simulation doesn't appear to hit the cache when the CTRL.C bit is cleared. Let's ensure there is no memory access within the disable and flush cache sequence, including to the stack. Signed-off-by: Nicolas Pitre <nico@linaro.org>
* | Merge tag 'remove-local-timers' of ↵Olof Johansson2013-07-231-1/+1
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup From Stephen Boyd: Now that we have a generic arch hook for broadcast we can remove the local timer API entirely. Doing so will reduce code in ARM core, reduce the architecture dependencies of our timer drivers, and simplify the code because we no longer go through an architecture layer that is essentially a hotplug notifier. * tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm: ARM: smp: Remove local timer API clocksource: time-armada-370-xp: Divorce from local timer API clocksource: time-armada-370-xp: Fix sparse warning ARM: msm: Divorce msm_timer from local timer API ARM: PRIMA2: Divorce timer-marco from local timer API ARM: EXYNOS4: Divorce mct from local timer API ARM: OMAP2+: Divorce from local timer API ARM: smp_twd: Divorce smp_twd from local timer API ARM: smp: Remove duplicate dummy timer implementation Resolved a large number of conflicts due to __cpuinit cleanups, etc. Signed-off-by: Olof Johansson <olof@lixom.net>
| * ARM: smp_twd: Divorce smp_twd from local timer APIStephen Boyd2013-06-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Separate the smp_twd timers from the local timer API. This will allow us to remove ARM local timer support in the near future and gets us closer to moving this driver to drivers/clocksource. Tested-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* | Merge tag 'soc-for-linus' of ↵Linus Torvalds2013-07-027-0/+324
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC specific changes from Arnd Bergmann: "These changes are all to SoC-specific code, a total of 33 branches on 17 platforms were pulled into this. Like last time, Renesas sh-mobile is now the platform with the most changes, followed by OMAP and EXYNOS. Two new platforms, TI Keystone and Rockchips RK3xxx are added in this branch, both containing almost no platform specific code at all, since they are using generic subsystem interfaces for clocks, pinctrl, interrupts etc. The device drivers are getting merged through the respective subsystem maintainer trees. One more SoC (u300) is now multiplatform capable and several others (shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving towards that goal with this series but need more work. Also noteworthy is the work on PCI here, which is traditionally part of the SoC specific code. With the changes done by Thomas Petazzoni, we can now more easily have PCI host controller drivers as loadable modules and keep them separate from the platform code in drivers/pci/host. This has already led to the discovery that three platforms (exynos, spear and imx) are actually using an identical PCIe host controller and will be able to share a driver once support for spear and imx is added." * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits) ARM: integrator: let pciv3 use mem/premem from device tree ARM: integrator: set local side PCI addresses right ARM: dts: Add pcie controller node for exynos5440-ssdk5440 ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC ARM: EXYNOS: Enable PCIe support for Exynos5440 pci: Add PCIe driver for Samsung Exynos ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data ARM: keystone: Move CPU bringup code to dedicated asm file ARM: multiplatform: always pick one CPU type ARM: imx: select syscon for IMX6SL ARM: keystone: select ARM_ERRATA_798181 only for SMP ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1 ARM: OMAP2+: AM43x: resolve SMP related build error dmaengine: edma: enable build for AM33XX ARM: edma: Add EDMA crossbar event mux support ARM: edma: Add DT and runtime PM support to the private EDMA API dmaengine: edma: Add TI EDMA device tree binding arm: add basic support for Rockchip RK3066a boards arm: add debug uarts for rockchip rk29xx and rk3xxx series arm: Add basic clocks for Rockchip rk3066a SoCs ...
| * | ARM: vexpress: Select multi-cluster SMP operation if requiredJon Medhurst2013-05-293-0/+23
| | | | | | | | | | | | | | | | | | | | | Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: vexpress/dcscb: handle platform coherency exit/setup and CCIDave Martin2013-05-294-20/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the required code to properly handle race free platform coherency exit to the DCSCB power down method. The power_up_setup callback is used to enable the CCI interface for the cluster being brought up. This must be done in assembly before the kernel environment is entered. Thanks to Achin Gupta and Nicolas Pitre for their help and contributions. Signed-off-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: vexpress/dcscb: do not hardcode number of CPUs per clusterNicolas Pitre2013-05-291-4/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If 4 CPUs are assumed, the A15x1-A7x1 model configuration would never shut down the initial cluster as the 0xf reset bit mask will never be observed. Let's construct this mask based on the provided information in the DCSCB config register for the number of CPUs per cluster. Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementationNicolas Pitre2013-05-291-15/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is possible for a CPU to be told to power up before it managed to power itself down. Solve this race with a usage count to deal with this possibility as mandated by the MCPM API definition. Signed-off-by: nicolas Pitre <nico@linaro.org> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: vexpress: introduce DCSCB supportNicolas Pitre2013-05-293-0/+173
| |/ | | | | | | | | | | | | | | | | | | | | | | This adds basic CPU and cluster reset controls on RTSM for the A15x4-A7x4 model configuration using the Dual Cluster System Configuration Block (DCSCB). The cache coherency interconnect (CCI) is not handled yet. Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
* | ARM: vexpress: Remove init_irq declaration in machine descriptionMaxime Ripard2013-05-241-2/+0
|/ | | | | | | | | | Commit ebafed7a ("ARM: irq: Call irqchip_init if no init_irq function is specified") removed the need to explictly setup the init_irq field in the machine description when using only irqchip_init. Remove that declaration for vexpress as well. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
* Merge tag '3.9-rc3-smp-6-tag' of ↵Linus Torvalds2013-05-071-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen Pull ARM Xen SMP updates from Stefano Stabellini: "This contains a bunch of Xen/ARM specific changes, including some fixes, SMP support for Xen on ARM, and moving the xenvm machine from mach-vexpress to mach-virt. The non-Xen files that are touched are arch/arm/Kconfig, to select ARM_PSCI on XEN, and arch/arm/boot/dts/Makefile, to build the xenvm DTB if CONFIG_ARCH_VIRT. Highlights: - Move xenvm to mach-virt. - Implement SMP support in Xen on ARM. - Add support for machine reboot and power off via Xen hypercalls" * tag '3.9-rc3-smp-6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen: xen/arm: remove duplicated include from enlighten.c xen/arm: use sched_op hypercalls for machine reboot and power off xenvm: add a simple PSCI node and a second cpu xen/arm: XEN selects ARM_PSCI xen: move the xenvm machine to mach-virt xen/arm: SMP support xen/arm: implement HYPERVISOR_vcpu_op xen/arm: actually pass a non-NULL percpu pointer to request_percpu_irq
| * xen: move the xenvm machine to mach-virtStefano Stabellini2013-04-251-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | xenvm is based on mach-vexpress, move it to mach-virt. Changes in v4: - update the dts Makefile too. Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> CC: Marc Zyngier <marc.zyngier@arm.com> CC: will.deacon@arm.com CC: arnd@arndb.de CC: rob.herring@calxeda.com
* | Merge tag 'cleanup-for-linus-2' of ↵Linus Torvalds2013-05-071-23/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC late cleanups from Arnd Bergmann: "These are cleanups and smaller changes that either depend on earlier feature branches or came in late during the development cycle. We normally try to get all cleanups early, so these are the exceptions: - A follow-up on the clocksource reworks, hopefully the last time we need to merge clocksource subsystem changes through arm-soc. A first set of patches was part of the original 3.10 arm-soc cleanup series because of interdependencies with timer drivers now moved out of arch/arm. - Migrating the SPEAr13xx platform away from using auxdata for DMA channel descriptions towards using information in device tree, based on the earlier SPEAr multiplatform series - A few follow-ups on the Atmel SAMA5 support and other changes for Atmel at91 based on the larger at91 reworks. - Moving the armada irqchip implementation to drivers/irqchip - Several OMAP cleanups following up on the larger series already merged in 3.10." * tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits) ARM: OMAP4: change the device names in usb_bind_phy ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a ARM: SPEAr: conditionalize SMP code ARM: arch_timer: Silence debug preempt warnings ARM: OMAP: remove unused variable serial: amba-pl011: fix !CONFIG_DMA_ENGINE case ata: arasan: remove the need for platform_data ARM: at91/sama5d34ek.dts: remove not needed compatibility string ARM: at91: dts: add MCI DMA support ARM: at91: dts: add i2c dma support ARM: at91: dts: set #dma-cells to the correct value ARM: at91: suspend both memory controllers on at91sam9263 irqchip: armada-370-xp: slightly cleanup irq controller driver irqchip: armada-370-xp: move IRQ handler to avoid forward declaration irqchip: move IRQ driver for Armada 370/XP ARM: mvebu: move L2 cache initialization in init_early() devtree: add binding documentation for sp804 ARM: integrator-cp: convert use CLKSRC_OF for timer init ARM: versatile: use OF init for sp804 timer ARM: versatile: add versatile dtbs to dtbs target ...
| * | ARM: vexpress: remove extra timer-sp control register clearingRob Herring2013-04-111-3/+0
| | | | | | | | | | | | | | | | | | | | | The timer-sp initialization code clears the control register before initializing the timers, so every platform doing this is redundant. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| * | ARM: vexpress: remove sp804 OF initRob Herring2013-04-111-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | Remove the vexpress specific setup for the sp804 timer now that clocksource_of_init will do it. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: convert arm/arm64 arch timer to use CLKSRC_OF initRob Herring2013-04-111-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts arm and arm64 to use CLKSRC_OF DT based initialization for the arch timer. A new function arch_timer_arch_init is added to allow for arch specific setup. This has a side effect of enabling sched_clock on omap5 and exynos5. There should not be any reason not to use the arch timers for sched_clock. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Simon Horman <horms@verge.net.au> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-samsung-soc@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-sh@vger.kernel.org Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
* | | Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds2013-05-031-2/+0
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM updates from Russell King: "The major items included in here are: - MCPM, multi-cluster power management, part of the infrastructure required for ARMs big.LITTLE support. - A rework of the ARM KVM code to allow re-use by ARM64. - Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes of that stuff for arch/arm - Preparatory patches for Cortex-M3 support from Uwe Kleine-König. There is also a set of three patches in here from Hugh/Catalin to address freeing of inappropriate page tables on LPAE. You already have these from akpm, but they were already part of my tree at the time he sent them, so unfortunately they'll end up with duplicate commits" * 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits) ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE() ARM: IMX: remove unnecessary use of IS_ERR_VALUE() ARM: OMAP: use consistent error checking ARM: cleanup: OMAP hwmod error checking ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels ARM: 7700/2: Make cpu_init() notrace ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE ARM: 7701/1: mm: Allow arch code to control the user page table ceiling ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum() ARM: mcpm: provide an interface to set the SMP ops at run time ARM: mcpm: generic SMP secondary bringup and hotplug support ARM: mcpm_head.S: vlock-based first man election ARM: mcpm: Add baremetal voting mutexes ARM: mcpm: introduce helpers for platform coherency exit/setup ARM: mcpm: introduce the CPU/cluster power API ARM: multi-cluster PM: secondary kernel entry code ARM: cacheflush: add synchronization helpers for mixed cache state accesses ARM: cpu hotplug: remove majority of cache flushing from platforms ARM: smp: flush L1 cache in cpu_die() ARM: tegra: remove tegra specific cpu_disable() ...
| * | | ARM: cpu hotplug: remove majority of cache flushing from platformsRussell King2013-04-181-2/+0
| | |/ | |/| | | | | | | | | | | | | | | | Remove the majority of cache flushing calls from the individual platform files. This is now handled by the core code. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | | Merge tag 'multiplatform-for-linus' of ↵Linus Torvalds2013-05-021-0/+2
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC multiplatform updates from Olof Johansson: "More multiplatform enablement for ARM platforms. The ones converted in this branch are: - bcm2835 - cns3xxx - sirf - nomadik - msx - spear - tegra - ux500 We're getting close to having most of them converted! One of the larger platforms remaining is Samsung Exynos, and there are a bunch of supporting patches in this merge window for it. There was a patch in this branch to a early version of multiplatform conversion, but it ended up being reverted due to need of more bake time. The revert commit is part of the branch since it would have required rebasing multiple dependent branches and they were stable by then" * tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits) mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms clocksource: nomadik-mtu: fix up clocksource/timer Revert "ARM: exynos: enable multiplatform support" ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ" ARM: exynos: enable multiplatform support rtc: s3c: make header file local mtd: onenand/samsung: make regs-onenand.h file local thermal/exynos: remove unnecessary header inclusions mmc: sdhci-s3c: remove platform dependencies ARM: samsung: move mfc device definition to s5p-dev-mfc.c ARM: exynos: move debug-macro.S to include/debug/ ARM: exynos: prepare for sparse IRQ ARM: exynos: introduce EXYNOS_ATAGS symbol ARM: tegra: build assembly files with -march=armv7-a ARM: Push selects for TWD/SCU into machine entries ARM: ux500: build hotplug.o for ARMv7-a ARM: ux500: move to multiplatform ARM: ux500: make remaining headers local ARM: ux500: make irqs.h local to platform ARM: ux500: get rid of <mach/[hardware|db8500-regs].h> ...
| * | | ARM: Push selects for TWD/SCU into machine entriesStephen Boyd2013-04-091-0/+2
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TWD and SCU configs are selected by default as long as MSM_SCORPIONMP is false and/or MCT is false. Implementing the logic this way certainly saves lines in the Kconfig but it precludes those machines which select MSM_SCORPIONMP or MCT from participating in the single zImage effort because when those machines are combined with other SMP capable machines the TWD and SCU are no longer selected by default. Push the select out to the machine entries so that we can compile these machines together and still select the appropriate configs. Cc: Barry Song <baohua.song@csr.com> Acked-by: David Brown <davidb@codeaurora.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Linus Walleij <linus.walleij@linaro.org> Acked-by: Pawel Moll <pawel.moll@arm.com> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Shiraz Hashim <shiraz.hashim@st.com> Acked-by: Simon Horman <horms@verge.net.au> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Tony Lindgren <tony@atomide.com> Acked-by: Viresh Kumar <viresh.linux@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* | | Merge tag 'cleanup-for-linus' of ↵Linus Torvalds2013-05-021-3/+3
|\ \ \ | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanup from Olof Johansson: "Here is a collection of cleanup patches. Among the pieces that stand out are: - The deletion of h720x platforms - Split of at91 non-dt platforms to their own Kconfig file to keep them separate - General cleanups and refactoring of i.MX and MXS platforms - Some restructuring of clock tables for OMAP - Convertion of PMC driver for Tegra to dt-only - Some renames of sunxi -> sun4i (Allwinner A10) - ... plus a bunch of other stuff that I haven't mentioned" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits) ARM: i.MX: remove unused ARCH_* configs ARM i.MX53: remove platform ahci support ARM: sunxi: Rework the restart code irqchip: sunxi: Rename sunxi to sun4i irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro clocksource: sunxi: Rename sunxi to sun4i clocksource: sunxi: make use of CLKSRC_OF clocksource: sunxi: Cleanup the timer code ARM: at91: remove trailing semicolon from macros ARM: at91/setup: fix trivial typos ARM: EXYNOS: remove "config EXYNOS_DEV_DRM" ARM: EXYNOS: change the name of USB ohci header ARM: SAMSUNG: Remove unnecessary code for dma ARM: S3C24XX: Remove unused GPIO drive strength register definitions ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412 ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410 ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC" ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI" ...
| * | ARM: smp_twd: convert to use CLKSRC_OF initRob Herring2013-03-111-3/+3
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have OF based init with CLKSRC_OF, convert smp_twd init function to use it and covert all callers of twd_local_timer_of_register. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: John Stultz <johnstul@us.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-omap@vger.kernel.org Cc: spear-devel@list.st.com Reviewed-by: Stephen Warren <swarren@nvidia.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Linus Walleij <linus.walleij@linaro.org>
* | Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6Linus Torvalds2013-04-304-147/+4
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull battery updates from Anton Vorontsov: "Highlights: - OpenFirmware/DeviceTree support for the Power Supply core: the core now automatically populates supplied_from hierarchy from the device tree. With these patches chargers and batteries can now lookup each other without the board files support shim. Rhyland Klein at NVIDIA did the work - New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the AB85xx core and depends on some recent changes to it, so that is why the driver comes through the battery tree. It has an appropriate ack from the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored the driver - Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes touch mfd parts, but these were acked by the appropriate MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of the work and lead the submission process. Minor changes, but still worth mentioning: - Battery temperature reporting fix for Nokia N900 phones - Versatile Express poweroff driver moved into drivers/power/reset/ - Tree-wide: use devm_kzalloc() where appropriate - Tree-wide: dev_pm_ops cleanups/fixes" * tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits) pm2301-charger: Fix suspend/resume charger-manager: Use kmemdup instead of kzalloc + memcpy power_supply: Populate supplied_from hierarchy from the device tree power_supply: Add core support for supplied_from power_supply: Define Binding for power-supplies rx51_battery: Fix reporting temperature hwmon: Add ST-Ericsson ABX500 hwmon driver ab8500_bmdata: Export abx500_res_to_temp tables for hwmon ab8500_{bmdata,fg}: Add const attributes to some data arrays ab8500_bmdata: Eliminate CamelCase warning of some variables ab8500_btemp: Make ab8500_btemp_get* interfaces public goldfish_battery: Use resource_size() lp8788-charger: Use PAGE_SIZE for the sysfs read operation max8925_power: Use devm_kzalloc() da9030_battery: Use devm_kzalloc() da9052-battery: Use devm_kzalloc() ds2760_battery: Use devm_kzalloc() ds2780_battery: Use devm_kzalloc() gpio-charger: Use devm_kzalloc() isp1704_charger: Use devm_kzalloc() ...
| * | arm: vexpress: Decouple vexpress-poweroff implementation from machine_descCatalin Marinas2013-03-211-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the pm_power_off and arm_pm_restart variable settings to the vexpress-poweroff.c driver to decouple it from the machine_desc definition. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
| * | arm: vexpress: Move the poweroff/restart code to drivers/power/resetCatalin Marinas2013-03-213-142/+4
| |/ | | | | | | | | | | | | | | This patch moves the arch/arm/mach-vexpress/reset.c functionality to drivers/platform/reset/ and adds the necessary Kconfig wiring. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Pawel Moll <pawel.moll@arm.com>
* | clk: vexpress: Add separate SP810 driverPawel Moll2013-04-181-1/+7
|/ | | | | | | | | | | | | | | Factor out the SP810 clocking code into a separate driver, selecting better (faster) parent at clk_prepare() time. This is to avoid problems with clocking infrastructure initialisation order, in particular to avoid dependency of fixed clock being initialized before SP810. It also makes vexpress platform OF-based clock initialisation code unnecessary. Signed-off-by: Pawel Moll <pawel.moll@arm.com> Tested-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Mike Turquette <mturquette@linaro.org> [mturquette@linaro.org: add .unprepare, FIXME comment, cleaned up code]
* Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux ↵Olof Johansson2013-01-143-20/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | into next/cleanup From Rob Herring: Initial irqchip init infrastructure and GIC and VIC clean-ups This creates irqchip initialization infrastructure from Thomas Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips and adapted to use the new infrastructure. All DT enabled platforms using GIC and VIC are converted over to use the new irqchip_init. * tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux: irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h ARM: picoxcell: use common irqchip_init function ARM: spear: use common irqchip_init function irqchip: Move ARM VIC to drivers/irqchip ARM: samsung: remove unused tick.h ARM: remove unneeded vic.h includes ARM: remove mach .handle_irq for VIC users ARM: VIC: set handle_arch_irq in VIC initialization ARM: VIC: shrink down vic.h irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h ARM: use common irqchip_init for GIC init irqchip: Move ARM GIC to drivers/irqchip ARM: remove mach .handle_irq for GIC users ARM: GIC: set handle_arch_irq in GIC initialization ARM: GIC: remove direct use of gic_raise_softirq ARM: GIC: remove assembly ifdefs from gic.h ARM: mach-ux500: use SGI0 to wake up the other core arm: add set_handle_irq() to register the parent IRQ controller handler function irqchip: add basic infrastructure irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS Fixed up massive merge conflicts with the timer cleanup due to adjacent changes: Signed-off-by: Olof Johansson <olof@lixom.net> Conflicts: arch/arm/mach-bcm/board_bcm.c arch/arm/mach-cns3xxx/cns3420vb.c arch/arm/mach-ep93xx/adssphere.c arch/arm/mach-ep93xx/edb93xx.c arch/arm/mach-ep93xx/gesbc9312.c arch/arm/mach-ep93xx/micro9.c arch/arm/mach-ep93xx/simone.c arch/arm/mach-ep93xx/snappercl15.c arch/arm/mach-ep93xx/ts72xx.c arch/arm/mach-ep93xx/vision_ep9307.c arch/arm/mach-highbank/highbank.c arch/arm/mach-imx/mach-imx6q.c arch/arm/mach-msm/board-dt-8960.c arch/arm/mach-netx/nxdb500.c arch/arm/mach-netx/nxdkn.c arch/arm/mach-netx/nxeb500hmi.c arch/arm/mach-nomadik/board-nhk8815.c arch/arm/mach-picoxcell/common.c arch/arm/mach-realview/realview_eb.c arch/arm/mach-realview/realview_pb1176.c arch/arm/mach-realview/realview_pb11mp.c arch/arm/mach-realview/realview_pba8.c arch/arm/mach-realview/realview_pbx.c arch/arm/mach-socfpga/socfpga.c arch/arm/mach-spear13xx/spear1310.c arch/arm/mach-spear13xx/spear1340.c arch/arm/mach-spear13xx/spear13xx.c arch/arm/mach-spear3xx/spear300.c arch/arm/mach-spear3xx/spear310.c arch/arm/mach-spear3xx/spear320.c arch/arm/mach-spear3xx/spear3xx.c arch/arm/mach-spear6xx/spear6xx.c arch/arm/mach-tegra/board-dt-tegra20.c arch/arm/mach-tegra/board-dt-tegra30.c arch/arm/mach-u300/core.c arch/arm/mach-ux500/board-mop500.c arch/arm/mach-ux500/cpu-db8500.c arch/arm/mach-versatile/versatile_ab.c arch/arm/mach-versatile/versatile_dt.c arch/arm/mach-versatile/versatile_pb.c arch/arm/mach-vexpress/v2m.c include/asm-generic/vmlinux.lds.h
| * irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.hRob Herring2013-01-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have GIC moved to drivers/irqchip and all GIC DT init for platforms using irqchip_init, move gic.h and update the remaining includes. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Samuel Ortiz <sameo@linux.intel.com>
| * ARM: use common irqchip_init for GIC initRob Herring2013-01-121-12/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert all GIC DT initialization over to use common irqchip_init function. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org>
| * ARM: remove mach .handle_irq for GIC usersRob Herring2013-01-122-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the GIC initialization sets up the handle_arch_irq pointer, we can remove it for all machines and make it static. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Acked-by: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Arnd Bergmann <arnd@arndb.de>
| * ARM: GIC: remove direct use of gic_raise_softirqRob Herring2013-01-102-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation of moving gic code to drivers/irqchip, remove the direct platform dependencies on gic_raise_softirq. Move the setup of smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask function to trigger wake-up IPIs. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shiraz Hashim <shiraz.hashim@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
* | Merge branch 'clocksource/cleanup' into next/cleanupOlof Johansson2013-01-141-1/+0
|\ \ | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clockevent cleanup series from Shawn Guo. Resolved move/change conflict in mach-pxa/time.c due to the sys_timer cleanup. * clocksource/cleanup: clocksource: use clockevents_config_and_register() where possible ARM: use clockevents_config_and_register() where possible clockevents: export clockevents_config_and_register for module use + sync to Linux 3.8-rc3 Signed-off-by: Olof Johansson <olof@lixom.net> Conflicts: arch/arm/mach-pxa/time.c
| * ARM: 7609/1: disable errata work-arounds which access secure registersRob Herring2013-01-021-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to support secure and non-secure platforms in multi-platform kernels, errata work-arounds that access secure only registers need to be disabled. Make all the errata options that fit in this category depend on !CONFIG_ARCH_MULTIPLATFORM. This will effectively remove the errata options as platforms are converted over to multi-platform. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | ARM: delete struct sys_timerStephen Warren2012-12-241-10/+2
|/ | | | | | | | | | | | | | | | | | Now that the only field in struct sys_timer is .init, delete the struct, and replace the machine descriptor .timer field with the initialization function itself. This will enable moving timer drivers into drivers/clocksource without having to place a public prototype of each struct sys_timer object into include/linux; the intent is to create a single of_clocksource_init() function that determines which timer driver to initialize by scanning the device dtree, much like the proposed irqchip_init() at: http://www.spinics.net/lists/arm-kernel/msg203686.html Includes mach-omap2 fixes from Igor Grinberg. Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds2012-12-131-0/+141
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM SoC driver specific changes from Olof Johansson: "A collection of mostly SoC-specific driver updates: - a handful of pincontrol and setup changes - new drivers for hwmon and reset controller for vexpress - timing support updates for OMAP (gpmc and other interfaces) - plus a collection of smaller cleanups" * tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits) ARM: ux500: fix pin warning ARM: OMAP2+: tusb6010: generic timing calculation ARM: OMAP2+: smc91x: generic timing calculation ARM: OMAP2+: onenand: generic timing calculation ARM: OMAP2+: gpmc: generic timing calculation ARM: OMAP2+: gpmc: handle additional timings ARM: OMAP2+: nand: remove redundant rounding gpio: samsung: use pr_* instead of printk ARM: ux500: fixup magnetometer pins ARM: ux500: add STM pin configuration ARM: ux500: 8500: add pinctrl support for uart1 and uart2 ARM: ux500: cosmetic fixups for uart0 gpio: samsung: Fix input mode setting function for GPIO int ARM: SAMSUNG: Insert bitmap_gpio_int member in samsung_gpio_chip ARM: ux500: 8500: define SDI sleep states ARM: vexpress: Reset driver ARM: ux500: 8500: update SKE keypad pinctrl table hwmon: Versatile Express hwmon driver ARM: ux500: delete duplicate macro ARM: ux500: 8500: add IDLE pin configuration for SPI ...
| * ARM: vexpress: Reset driverPawel Moll2012-10-181-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a simple driver providing platform restart and power off functions using VE config infrastructure. By writing to the "active" attribute of the reboot or reset device, user can decide what if the platform is supposed to execute full power cycle (reboot, default) or simply assert system level reset signal. Signed-off-by: Pawel Moll <pawel.moll@arm.com> Conflicts: include/linux/vexpress.h
* | Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds2012-12-126-371/+109
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM SoC updates from Olof Johansson: "This contains the bulk of new SoC development for this merge window. Two new platforms have been added, the sunxi platforms (Allwinner A1x SoCs) by Maxime Ripard, and a generic Broadcom platform for a new series of ARMv7 platforms from them, where the hope is that we can keep the platform code generic enough to have them all share one mach directory. The new Broadcom platform is contributed by Christian Daudt. Highbank has grown support for Calxeda's next generation of hardware, ECX-2000. clps711x has seen a lot of cleanup from Alexander Shiyan, and he's also taken on maintainership of the platform. Beyond this there has been a bunch of work from a number of people on converting more platforms to IRQ domains, pinctrl conversion, cleanup and general feature enablement across most of the active platforms." Fix up trivial conflicts as per Olof. * tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits) mfd: vexpress-sysreg: Remove LEDs code irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids irq: versatile: delete dangling variable ARM: sunxi: add missing include for mdelay() ARM: EXYNOS: Avoid early use of of_machine_is_compatible() ARM: dts: add node for PL330 MDMA1 controller for exynos4 ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412 ARM: EXYNOS: add UART3 to DEBUG_LL ports ARM: S3C24XX: Add clkdev entry for camif-upll clock ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers ARM: sunxi: Add missing sun4i.dtsi file pinctrl: samsung: Do not initialise statics to 0 ARM i.MX6: remove gate_mask from pllv3 ARM i.MX6: Fix ethernet PLL clocks ARM i.MX6: rename PLLs according to datasheet ARM i.MX6: Add pwm support ARM i.MX51: Add pwm support ARM i.MX53: Add pwm support ARM: mx5: Replace clk_register_clkdev with clock DT lookup ...
| * | ARM: vexpress: Remove motherboard dependencies in the DTS filesPawel Moll2012-11-051-8/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The way the VE motherboard Device Trees were constructed enforced naming and structure of daughterboard files. This patch makes it possible to simply include the motherboard description anywhere in the main Device Tree and retires the "arm,v2m-timer" alias - any of the motherboard SP804 timers will be used instead. Signed-off-by: Pawel Moll <pawel.moll@arm.com>
| * | ARM: vexpress: Start using new Versatile Express infrastructurePawel Moll2012-11-056-364/+99
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch starts using all the configuration infrastructure. - generic GPIO library is forced now - sysreg GPIOs are used as MMC CD and WP information sources; thanks to this MMCI auxiliary data is not longer necessary - DVI muxer and mode control is removed from non-DT V2P-CA9 code as this is now handled by the vexpress-dvi driver - clock generators control is removed as is being handled by the common clock driver now - the sysreg and sysctl control is now delegated to the appropriate drivers and all related code was removed - NOR Flash set_vpp function has been removed as the control bit used does _not_ control its VPP line, but the #WP signal instead (which is de facto unusable in case of Linux MTD drivers); this also allowed the remove its DT auxiliary data The non-DT code defines only minimal required number of the config devices. Device Trees are updated to make use of all new features. Signed-off-by: Pawel Moll <pawel.moll@arm.com>
* | Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"Randy Dunlap2012-11-301-1/+1
|/ | | | | | | | | ERROR: "allnodes" [drivers/w1/masters/w1-gpio.ko] undefined! Signed-off-by: Randy Dunlap <rdunlap@infradead.org> [grant.likely: allnodes is too generic; rename to of_allnodes] Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Ville Syrjala <syrjala@sci.fi>
* Merge tag 'stable/for-linus-3.7-arm-tag' of ↵Linus Torvalds2012-10-071-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull ADM Xen support from Konrad Rzeszutek Wilk: Features: * Allow a Linux guest to boot as initial domain and as normal guests on Xen on ARM (specifically ARMv7 with virtualized extensions). PV console, block and network frontend/backends are working. Bug-fixes: * Fix compile linux-next fallout. * Fix PVHVM bootup crashing. The Xen-unstable hypervisor (so will be 4.3 in a ~6 months), supports ARMv7 platforms. The goal in implementing this architecture is to exploit the hardware as much as possible. That means use as little as possible of PV operations (so no PV MMU) - and use existing PV drivers for I/Os (network, block, console, etc). This is similar to how PVHVM guests operate in X86 platform nowadays - except that on ARM there is no need for QEMU. The end result is that we share a lot of the generic Xen drivers and infrastructure. Details on how to compile/boot/etc are available at this Wiki: http://wiki.xen.org/wiki/Xen_ARMv7_with_Virtualization_Extensions and this blog has links to a technical discussion/presentations on the overall architecture: http://blog.xen.org/index.php/2012/09/21/xensummit-sessions-new-pvh-virtualisation-mode-for-arm-cortex-a15arm-servers-and-x86/ * tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (21 commits) xen/xen_initial_domain: check that xen_start_info is initialized xen: mark xen_init_IRQ __init xen/Makefile: fix dom-y build arm: introduce a DTS for Xen unprivileged virtual machines MAINTAINERS: add myself as Xen ARM maintainer xen/arm: compile netback xen/arm: compile blkfront and blkback xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree xen/arm: receive Xen events on ARM xen/arm: initialize grant_table on ARM xen/arm: get privilege status xen/arm: introduce CONFIG_XEN on ARM xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM xen/arm: Introduce xen_ulong_t for unsigned long xen/arm: Xen detection and shared_info page mapping docs: Xen ARM DT bindings xen/arm: empty implementation of grant_table arch specific functions xen/arm: sync_bitops xen/arm: page.h definitions xen/arm: hypercalls ...
OpenPOWER on IntegriCloud