summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/clock.h
Commit message (Collapse)AuthorAgeFilesLines
* ARM: OMAP2+: clock: add support for indexed memmapsTero Kristo2014-01-171-0/+5
| | | | | | | | | | | Using indexed memmaps is required for isolating the actual memory access from the clock code. Now, the driver providing the support for the clock IP block provides the low level routines for reading/writing clock registers also. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* CLK: TI: add interface clock support for OMAP3Tero Kristo2014-01-171-5/+0
| | | | | | | | | | OMAP3 has interface clocks in addition to functional clocks, which require special handling for the autoidle and idle status register offsets mainly. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* CLK: TI: add am33xx clock init fileTero Kristo2014-01-171-1/+0
| | | | | | | | | | | | | clk-33xx.c now contains the clock init functionality for am33xx, including DT clock registration and adding of static clkdev entries. This patch also moves the omap2_clk_enable_init_clocks declaration to the driver include, as this is needed by the am33xx clock init code. Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* CLK: TI: add omap4 clock init fileTero Kristo2014-01-171-1/+0
| | | | | | | | | | clk-44xx.c now contains the clock init functionality for omap4, including DT clock registration and adding of static clkdev entries. Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* clk: ti: add composite clock supportTero Kristo2014-01-171-3/+0
| | | | | | | | | | This is a multipurpose clock node, which contains support for multiple sub-clocks. Uses basic composite clock type to implement the actual functionality, and TI specific gate, mux and divider clocks. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* CLK: TI: Add DPLL clock supportTero Kristo2014-01-171-163/+1
| | | | | | | | | The OMAP clock driver now supports DPLL clock type. This patch also adds support for DT DPLL nodes. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
* ARM: OMAP3: clock: add API to enable/disable autoidle for a single clockTero Kristo2013-10-191-0/+2
| | | | | | | | | Some drivers require direct access to the autoidle functionality of the interface clocks. Added clock APIs for these, so that the drivers do not need to access CM registers directly. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2+: clock data: Remove CK_* flagsJ Keerthy2013-03-181-18/+2
| | | | | | | | | | | | | | | | The patch removes all the CK_* which were used to identify the family of processors for which the individual clocks belonged to. Instead now separate lists are created based on the family of processors. Boot Tested on: OMAP4430, OMAP4460, Beagle-board, AM33X boards, OMAP2 boards. Signed-off-by: J Keerthy <j-keerthy@ti.com> Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com> Tested-by: Jon Hunter <jon-hunter@ti.com> Cc: Paul Walmsley <paul@pwsan.com> [paul@pwsan.com: changed omap_clock_register_links() to omap_clocks_register(); updated to apply] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2+: clock data: add DEFINE_STRUCT_CLK_FLAGS helperAfzal Mohammed2013-01-311-0/+11
| | | | | | | | | DEFINE_STRUCT_CLK does not have the capability to set flags, define DEFINE_STRUCT_CLK_FLAGS to handle flags. This is needed to add SET_RATE_PARENT flag in statically defined lcd clock in am335x. Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP4: Enhance support for DPLLs with 4X multiplierJon Hunter2012-12-151-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can be enabled or disabled in addition to the standard configurable multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X multiplier is accounted for by checking to see whether it is enabled or not. However, when calculating a new rate we only check to see if the rate can be achieved with the current setting for the 4X multiplier. Enhance the round_rate() function for such DPLLs to see if the rate can be achieved with the 4X multiplier if it cannot be achieved without the 4X multiplier. This change is necessary, because when using the 32kHz clock as the source clock for the ABE DPLL, the default DPLL frequency for the ABE DPLL cannot be achieved without enabling the 4X multiplier. When using the 32kHz clock as the source clock for the ABE DPLL and attempting to lock the DPLL to 98.304MHz (default frequency), it was found that the DPLL would fail to lock if the low-power mode for the DPLL was not enabled. From reviewing boot-loader settings that configure the ABE DPLL it was found that the low-power mode is enabled when using the 32kHz clock source, however, the documentation for OMAP does not state that this is a requirement. Therefore, introduce a new function for OMAP4 devices to see if low-power mode can be enabled when calculating a new rate to ensure the DPLL will lock. New variables for the last calculated 4X multiplier and low-power setting have been added to the dpll data structure as well as variables defining the bit mask for enabling these features via the DPLL's control_reg. It is possible that we could eliminate these bit masks from the dpll data structure as these bit masks are not unique to OMAP4, if it is preferred. The function omap3_noncore_program_dpll() has been updated to avoid passing the calculated values for the multiplier (M) and divider (N) as these are stored in the clk structure. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK partsMike Turquette2012-11-121-220/+1
| | | | | | | | | | Clean all #ifdef's added to common clock code. This code is no longer needed due to migration to the common clock framework. Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: clean up new ifdefs added in clockdomain.c] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK partsRajendra Nayak2012-11-121-16/+0
| | | | | | | | | | Clean all #ifdef's added to OMAP3 clock code to make it COMMON clk ready, not that CONFIG_COMMON_CLK is enabled. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: remove some ifdefs in mach-omap2/io.c] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP4: clock: Add 44xx data using common struct clkRajendra Nayak2012-11-121-0/+2
| | | | | | | | | | | | | | | | | | | | This patch is output from updated omap hw data autogeneration scripts mostly contributed by Mike Turquette, with some later fixes from me. All data is added into a new cclock44xx_data.c file which will be switched with clock44xx_data.c file in a later patch. Signed-off-by: Rajendra Nayak <rnayak@ti.com> [paul@pwsan.com: replace omap2_init_clksel_parent() with omap2_clksel_find_parent_index(); reflowed macros; updated DEFINE_STRUCT_CLK_HW_OMAP macro to include clkdm_name; use macros for clksel mux+gate clocks; many other fixes] [mturquette@ti.com: converted DPLL outputs to HSDIVIDER macro; trace_clk_div_ck has clkdm ops] Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: fixed the omap-gpmc.fck alias per commit a2e5b90b; fixed several checkpatch issues; moved the dpll3xxx.c clockdomain modifications to another patch] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2+: clock: add OMAP CCF convenience macros to mach-omap2/clock.hPaul Walmsley2012-11-121-0/+77
| | | | | | | | | | | | | | | | Define four convenience macros to be used in the upcoming OMAP2+ common clock framework port. Although the use of these macros will make the data somewhat more difficult to read, they significantly reduce the number of lines in the output patch data. Most of these were created by Rajendra Nayak and Mike Turquette, as far as I know. Signed-off-by: Paul Walmsley <paul@pwsan.com> [mturquette@ti.com: added DEFINE_CLK_OMAP_HSDIVIDER macro] Signed-off-by: Mike Turquette <mturquette@ti.com> Cc: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP: clock: Define a function to enable clocks at initRajendra Nayak2012-11-121-0/+1
| | | | | | | | | Platform code can use omap2_clk_enable_init_clocks() to enable a list of clocks that are needed to be enabled at init. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: added kerneldoc to non-trivial new function] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP: clock: list all clk_hw_omap clks to enable/disable autoidleRajendra Nayak2012-11-121-0/+3
| | | | | | | | | | | | Platforms can call omap2_init_clk_hw_omap_clocks() to register a clock using clk_hw_omap. omap2_clk_enable_autoidle_all() and omap2_clk_disable_autoidle_all() can then be used to run through all the clocks which support autoidle to enable/disable them. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: added kerneldoc on non-trivial new functions] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP3: clock: Convert to common clkRajendra Nayak2012-11-121-2/+20
| | | | | | | | | | | Convert all OMAP3 specific platform files to use COMMON clk and keep all the changes under the CONFIG_COMMON_CLK macro check so it does not break any existing code. At a later point switch to COMMON clk and get rid of all old/legacy code. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP4: clock: Convert to common clkMike Turquette2012-11-121-2/+75
| | | | | | | | | | | | | | | | | | | | | | | | | Convert all OMAP4 specific platform files to use COMMON clk and keep all the changes under the CONFIG_COMMON_CLK macro check so it does not break any existing code. At a later point switch to COMMON clk and get rid of all old/legacy code. This converts all apis which will be called directly from COMMON clk to take a struct clk_hw parameter, and all the internal platform apis to take a struct clk_hw_omap parameter. Changes are based off the original patch from Mike Turquette. Signed-off-by: Rajendra Nayak <rnayak@ti.com> [paul@pwsan.com: created new omap2_clksel_find_parent_index() rather than modifying omap2_init_clksel_parent(); moved clkhwops_iclk_wait to clkt_iclk.c to fix OMAP4-only builds; added clk-provider.h include to clock.h to try to fix some 3430-builds] [mturquette@ti.com: squash patch for omap2_clkops_{en,dis}able_clkdm; omap2_dflt_clk_is_enabled should not enable clocks] Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: fix compiler warning; update to apply; added kerneldoc on non-trivial new functions; added the dpll3xxx clockdomain modifications] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP: clock: Nuke plat/clock.c & reuse struct clk as clk_hw_omapRajendra Nayak2012-11-121-0/+64
| | | | | | | | | | | | | | | | | plat/clock.c which has most of usecounting/locking infrastructure will be used only for OMAP1 until that is moved to use COMMON clk. reuse most of what plat/clock.h has while we move to common clk, and move most of what 'struct clk' was as 'struct clk_hw_omap' which will then be used to define platform specific parameters. All usecounting/locking related variables from 'struct clk' are dropped as they will not be used with 'struct clk_hw_omap'. Based on the original changes from Mike Turquette. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2+: board files: use SoC-specific system restart functionsPaul Walmsley2012-11-081-28/+0
| | | | | | | | | | | | Modify the board files to use the SoC-specific system restart functions. At this point it's possible to remove omap_prcm_restart() from mach-omap2/prcm.c. While removing the prototypes for the now-unused restart functions, clean up a few more obsolete prototypes in mach-omap2/clock.h. Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
* ARM: OMAP: clock: split plat/clkdev_omap.h into OMAP1/2 filesPaul Walmsley2012-10-181-0/+33
| | | | | | | | | To facilitate the ARM single image work, split arch/arm/plat-omap/include/plat/clkdev_omap.h into the arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h files. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP: remove plat/clock.hPaul Walmsley2012-10-181-1/+283
| | | | | | | | | | | Remove arch/arm/plat-omap/include/plat/clock.h by merging it into arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h. The goal here is to facilitate ARM single image kernels by removing includes via the "plat/" symlink. Signed-off-by: Paul Walmsley <paul@pwsan.com> [tony@atomide.com: fixed to remove duplicate clock.h includes] Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP3+: clock33xx: Add AM33XX clock tree dataVaibhav Hiremath2012-06-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | AM33XX clock implementation is different than any existing OMAP family of devices. Although DPLL module is similar to OMAP4 device, but the usage is very much different than OMAP4. AM33XX has different peripheral set and each module gets integrated to the clock framework differently than OMAP family of devices. This patch adds full Clock tree data for AM33XX family of devices and also integrates it into existing OMAP framework. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Rajendra Nayak <rnayak@ti.com> CC: Tony Lindgren <tony@atomide.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Benoit Cousson <b-cousson@ti.com> [paul@pwsan.com: updated to apply; changed 'soc_is_am33xx' to 'cpu_is_am33xx' to match usage in Tony's current am33xx branch] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP3+: clock: Move common clksel_rate & clock data to common filePaul Walmsley2012-06-261-0/+12
| | | | | | | | | | | | OMAP3, OMAP4 and AM33xx share some common data like, clksel_rate oscillator clock input (Virtual clock nodes), required for clock tree; so move common data to common data file so that it can be reused. [hvaibhav@ti.com: Created separate commit from Paul's developement branch] Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errorsKevin Hilman2012-04-141-8/+0
| | | | | | | | | | | | | | | | | | | Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no longer need/use the clock framework code for filling up CPUfreq tables. Remove it. Removing this code also eliminates build errors when CPU_FREQ_TABLE support is not enabled. Thanks to Russell King for pointing out the parts I missed under plat-omap in the original version and also pointing out the build errors when CPUFREQ_TABLE support was not enabled. Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Kevin Hilman <khilman@ti.com> Acked-by: Paul Walmsley <paul@pwsan.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Olof Johansson <olof@lixom.net>
* ARM: OMAP: am33xx: Update common omap platform filesAfzal Mohammed2011-12-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | This patch updates the common platform files with AM335X device support (AM33XX family). The approach taken in this patch is, AM33XX device will be considered as OMAP3 variant, and a separate SoC class created for AM33XX family of devices with a subclass type for AM335X device, which is newly added device in the family. This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x() checks will return success on AM335X device. A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3 to include support for AM33XX build. Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence struct clksel_rate.flags, struct prcm_config.flags and cpu_mask are changed to u16 from u8. Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Hemant Pedanekar <hemantp@ti.com> [tony@atomide.com: left out CK_AM33XX for now] Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP4: clock: round_rate and recalc functions for DPLL_ABEMike Turquette2011-10-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN bit in CKGEN module of CM1. From the OMAP4 TRM: Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only applicable to DPLL_ABE). Add new round_rate() and recalc() functions for OMAP4, that check the setting of REGM4XEN bit and handle this appropriately. The new functions are a simple wrapper on top of the existing omap2_dpll_round_rate() and omap2_dpll_get_rate() functions to handle the REGM4XEN bit. The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and omap4_dpll_regm4xen_recalc() functions. Signed-off-by: Mike Turquette <mturquette@ti.com> Tested-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com> [paul@pwsan.com: fixed attempt to return a negative from a fn returning unsigned; pass along errors from omap2_dpll_round_rate(); added documentation; added Jon's S-o-b] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls ↵Paul Walmsley2011-07-101-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | from clock code The OMAP2/3 clock code was written to notify the clockdomain code when the first clock in a clockdomain is enabled and when the last enabled clock in a clockdomain is disabled. OMAP4 requires a different approach: the hwmod code needs to signal the clockdomain code when to force-enable and auto-idle a clockdomain during the IP block enable process. The current conjecture is that once that hwmod sequence is implemented, it will no longer be necessary for the clock code to call into the clockdomain code for "optional clocks" on OMAP4. Add a static flag to the OMAP2+ clock code, clkdm_control, that by default preserves the OMAP2/3 behavior. Also add a function, omap2_clk_disable_clkdm_control(), intended to be called from OMAP4 and beyond clock initcalls, that disables the old behavior. Part of this patch was originally based on a patch by Rajendra Nayak <rnayak@ti.com>. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Rajendra Nayak <rnayak@ti.com>
* OMAP2xxx: clock: remove dsp_irate_ickPaul Walmsley2011-03-071-0/+1
| | | | | | | | | | | After commit 81b34fbecbfbf24ed95c2d80d5cb14149652408f ("OMAP2 clock: split OMAP2420, OMAP2430 clock data into their own files"), it's possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock files. It was originally only needed due to a 2420/2430 clock tree difference, and now that the data is in separate files, it's superfluous. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2+: clock: remove the DPLL rate tolerance codePaul Walmsley2011-03-071-4/+0
| | | | | | | | | | Remove the DPLL rate tolerance code that is called during rate rounding. As far as I know, this code is never used, since it's been more important for callers of the DPLL round_rate()/set_rate() functions to obtain an exact rate than it is to save a relatively small amount of power. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2430/3xxx: clock: add modem clock autoidle supportPaul Walmsley2011-03-071-0/+1
| | | | | | | | | | OMAP2430 and OMAP3xxx have modem autoidle bits that are actually attached to clocks with CM_FCLKEN bits; add the code and data to handle these. Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
* OMAP2+: clock: add interface clock type code with autoidle supportPaul Walmsley2011-03-071-1/+8
| | | | | | | | | | | Add interface clock type code with autoidle enable/disable support. The clkops structures created in this file will be used for all OMAP2/3 interface clocks with autoidle support. They will enable the clock framework to control interface clock autoidle directly. Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
* OMAP2: clock: add DPLL autoidle supportPaul Walmsley2011-03-071-0/+1
| | | | | | | | | | | | | | | Add the necessary code and data to allow the clock framework to enable and disable the OMAP2 DPLL autoidle state. This is so the direct register access can be moved out of the mach-omap2/pm24xx.c code, and other code that needs to control this (e.g., CPUIdle) can do so via an API. As part of this patch, remove the pm24xx.c code that formerly wrote directly to the autoidle bits. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
* omap4: dpll: Enable auto gate control for all MX postdividersRajendra Nayak2011-02-251-0/+1
| | | | | | | | | | Enable hardware gate control for all dpll MX and X2 postdividers. This requires the allow_idle/deny_idle functions to be populated for all clock nodes (mx/x2 post dividers) in clkops. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP4: DPLL: Add dpll api to control GATE_CTRLRajendra Nayak2011-02-251-0/+3
| | | | | | | | | | | | | | | | | | | | | On OMAP4, the dpll post divider outputs (MX outputs) along with clockout_x2 output provide a way to allow/deny hardware level autogating. Allowing autoidle would mean that the hw would autogate this clock when there is no dependency for it. Denying idle would mean that this clock output will be forced to stay enabled. Add dpll api's to read/allow/deny idle control for these dpll mx postdividers. NOTE: The gatectrl bit set to 0 allows gatectrl, and the bit set to 1 denies gatectrl. Signed-off-by: Rajendra Nayak <rnayak@ti.com> [paul@pwsan.com: moved OMAP4-specific DPLL control code to mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP3/4: DPLL: Add allow_idle/deny_idle support for all DPLL'sRajendra Nayak2011-02-251-0/+1
| | | | | | | | | All OMAP3/4 dpll's support hardware level autogating. Populate allow_idle/deny_idle function pointers for all DPLL's in clkops. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP: clock: fix configuration of J-Type DPLLs to work for OMAP3 and OMAP4Jon Hunter2010-12-211-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | J-Type DPLLs have additional configuration parameters that need to be programmed when setting the multipler and divider for the DPLL. These parameters being the sigma delta divider (SD_DIV) for the DPLL and the digital controlled oscillator (DCO) to be used by the DPLL. The current code is implemented specifically to configure the OMAP3630 PER J-Type DPLL. The OMAP4430 USB DPLL is also a J-Type DPLL and so this code needs to be updated to work for both OMAP3 and OMAP4 devices and any other future devices that have J-TYPE DPLLs. For the OMAP3630 PER DPLL both the SD_DIV and DCO paramenters are used but for the OMAP4430 USB DPLL only the SD_DIV field is used. The current implementation will only program the SD_DIV and DCO fields if the DPLL has both and hence this does not work for OMAP4430. In order to make the code more generic add two new fields to the dpll_data structure for the SD_DIV field and DCO field bit-masks and only program these fields if the masks are defined for a specific DPLL. This simplifies the code and allows us to remove the flag DPLL_NO_DCO_SEL. Tested on OMAP36xx Zoom3 and OMAP4 Blaze. Signed-off-by: Jon Hunter <jon-hunter@ti.com> [paul@pwsan.com: removed explicit inlining and added '_' prefix on lookup_*() functions; added testing info to commit message; added 35xx comments back in] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2+ clock: clean up clkt_clksel.cPaul Walmsley2010-05-201-5/+6
| | | | | | | | | | | | | | | | | | | This patch cleans up arch/arm/mach-omap2/clkt_clksel.c. It: - makes several functions static that are not called outside the file; - adds documentation; - makes some code paths easier to read (hopefully), by breaking up compound statements and removing redundant checks; - converts some pr_err()s that indicate clock tree data problems into WARN()s, so they are more likely to be noticed; - and moves omap2_clk_round_rate() back into mach-omap2/clock.c, its proper home, since it is not clksel-specific. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP4: clock: Add dummy clock nodes for interface clocksSantosh Shilimkar2010-02-241-0/+1
| | | | | | | | | | | | | | | | On OMAP4 platform the iclk control is completly under hardware control and no software control is available. This difference w.r.t previous OMAP's needs all the common driver accross OMAP's , cpu_is_xxxx() checks. To avoid poulluting the drivers dummy clock nodes are created (The autogeneration script has been updated accordingly). Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Benoit Cousson <b-cousson@ti.com> [paul@pwsan.com: made OMAP1 dummy_ck common and edited patch to reuse that] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change codePaul Walmsley2010-02-241-0/+4
| | | | | | | | The OMAP2 and OMAP3 boot-time MPU rate change code is almost identical. Merge them into mach-omap2/clock.c, and add kerneldoc documentation. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2 clock: drop DELAYED_APP clock flagPaul Walmsley2010-02-241-1/+0
| | | | | | | | | | | | | | | | All of the clocks that are marked with DELAYED_APP are changed as part of the virt_prcm_set OPP virtual clock. On 24xx, these clocks all need to be changed as part of a group to keep the clock tree functional - hence the need for the VALID_CONFIG bit, which is not present on later OMAPs. These clocks should not be rate-changed independently. So prevent these clocks from being changed independently by dropping their .round_rate and .set_rate function pointers. It then turns out that the DELAYED_APP clock flag is no longer useful, so drop it and the associated code and renumber the clock flags. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Richard Woodruff <r-woodruff2@ti.com>
* OMAP3/4 clock: split into per-chip family filesPaul Walmsley2010-02-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | clock34xx_data.c now contains data for the OMAP34xx family, the OMAP36xx family, and the OMAP3517 family, so rename it to clock3xxx_data.c. Rename clock34xx.c to clock3xxx.c, and move the chip family-specific clock functions to clock34xx.c, clock36xx.c, or clock3517.c, as appropriate. So now "clock3xxx.*" refers to the OMAP3 superset. The main goal here is to prepare to compile chip family-specific clock functions only for kernel builds that target that chip family. To get to that point, we also need to add CONFIG_SOC_* options for those other chip families; that will be done in future patches, planned for 2.6.35. OMAP4 is also affected by this. It duplicated the OMAP3 non-CORE DPLL clkops structure. The OMAP4 variant of this clkops structure has been removed, and since there was nothing else currently in clock44xx.c, it too has been removed -- it can always be added back later when there is some content for it. (The OMAP4 clock autogeneration scripts have been updated accordingly.) Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Rajendra Nayak <rnayak@ti.com> Cc: Ranjith Lohithakshan <ranjithl@ti.com> Cc: Tony Lindgren <tony@atomide.com>
* OMAP3 clock: introduce DPLL4 JtypeRichard Woodruff2010-02-241-0/+4
| | | | | | | | | | | | | | | | DPLL4 for 3630 introduces a changed block called j type dpll, requiring special divisor bits and additional reg fields. To allow for silicons to use this, this is introduced as a flag and is enabled for 3630 silicon. OMAP4 also has j type dpll for usb. Tested with 3630 ZOOM3 and OMAP3430 ZOOM2 Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com> [paul@pwsan.com: added some comments; updated copyrights and credits; fixed some style issues] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2/3 clock: Extend find_idlest() to pass back idle state valueRanjith Lohithakshan2010-02-241-1/+1
| | | | | | | | | | | | | | | | Current implementation defines clock idle state indicators based on the cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide manner. This patch extends the find_idlest() function in clkops to pass back the idle state indicator for that clock, thus allowing idle state indicators to be defined on a per clock basis if required. This is specifically needed on AM35xx devices as the new IPSS clocks indicates the idle status (0 is idle, 1 is ready) in a way just opposite to how its handled in OMAP3 (0 is ready, 1 is idle). Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com> [paul@pwsan.com: updated to apply after commit 98c45457 et seq.] Signed-off-by: Paul Walmsley <paul@pwsan.com>
* omap2: Convert ARCH_OMAP24XX to ARCH_OMAP2Tony Lindgren2010-02-151-1/+1
| | | | | | Convert ARCH_OMAP24XX to ARCH_OMAP2 Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap2/3: Multiboot compile fixes to compile in omap2 and omap3Tony Lindgren2010-02-151-0/+26
| | | | | | Allows compiling in omap2 and omap3. Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP2/3/4 clock: rename and clean the omap2_clk_init() functionsPaul Walmsley2010-01-291-1/+0
| | | | | | | | | | | | | | | Rename the omap2_clk_init() in the OMAP2, 3, and 4 clock code to be omap2xxx_clk_init(), omap3xxx_clk_init(), etc. Remove all traces of the (commented) old virt_prcm_set code from omap3xxx_clk_init() and omap4xxx_clk_init(), since this will be handled with the OPP code that is cooking in the PM branch. After this patch, there should be very little else in the clock code that blocks a multi-OMAP 2+3 kernel. (OMAP2420+OMAP2430 still has some outstanding issues that need to be resolved; this is pending on some additions to the hwmod data.) Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2/3/4 clock: omap2_clk_prepare_for_reboot() is OMAP2xxx-onlyPaul Walmsley2010-01-291-1/+0
| | | | | | | | omap2_clk_prepare_for_reboot() is only applicable to OMAP2xxx chips, so rename it to omap2xxx_clk_prepare_for_reboot() and only call it when running on OMAP2xxx chips. Remove the old stub in the OMAP3 clock code. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP2/3/4 clock: combine all omap2_clk_functionsPaul Walmsley2010-01-261-0/+7
| | | | | | | | | | | | The struct clk_functions for OMAP2, 3, and 4 are all essentially the same, so combine them. This removes one multi-OMAP kernel impediment and saves memory on multi-OMAP builds. The stubs for omap2_clk_{init,exit}_cpufreq() code will removed once the OPP layer code that's currently in Kevin's PM branch is merged. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@deeprootsystems.com>
* OMAP2/3/4 clock: move clksel clock functions into mach-omap2/clkt_clksel.cPaul Walmsley2010-01-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | Move all clksel-related clock functions from mach-omap2/clock.c to mach-omap2/clkt_clksel.c. This is intended to make the clock code easier to understand, since all of the functions needed to manage clksel clocks are now located in their own file, rather than being mixed with other, unrelated functions. Clock debugging is also now more finely-grained, since the DEBUG macro can now be defined for clksel clocks alon. This should reduce unnecessary console noise when debugging. Also, if at some future point the mach-omap2/ directory is split into OMAP2/3/4 variants, this clkt file can be moved to the plat-omap/ directory to be shared. Thanks to Alexander Shishkin <virtuoso@slind.org> for his comments to improve the patch description. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Alexander Shishkin <virtuoso@slind.org>
OpenPOWER on IntegriCloud