summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/board-omap3evm.c
Commit message (Collapse)AuthorAgeFilesLines
* arm: omap: switch over to gpio_set_debounceFelipe Balbi2010-05-271-3/+1
| | | | | | | | | | | | Stop using the omap-specific implementations for gpio debouncing now that gpiolib provides its own support. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: Tony Lindgren <tony@atomide.com> Cc: David Brownell <david-b@pacbell.net> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'omap-for-linus' of ↵Linus Torvalds2010-05-211-3/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits) omap4: Add support for i2c init omap: Fix i2c platform init code for omap4 OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y OMAP powerdomain, hwmod, omap_device: add some credits OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains OMAP: timers: Fix clock source names for OMAP4 OMAP4 clock: Support clk_set_parent OMAP4: PRCM: Add offset defines for all CM registers OMAP4: PRCM: Add offset defines for all PRM registers OMAP4: PRCM: Remove duplicate definition of base addresses OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention OMAP4: CM: Remove non-functional registers in ES1.0 OMAP: hwmod: Replace WARN by pr_warning for clockdomain check OMAP: hwmod: Rename hwmod name for the MPU OMAP: hwmod: Do not exit the iteration if one clock init failed OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value OMAP: hwmod: Fix wrong pointer iteration in oh->slaves ...
| * OMAP3: PM: Enable wakeup from ads7846 touchscreenRanjith Lohithakshan2010-05-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables the wakeup capabilities of ads7846 touchscreen driver. ads7846 driver can now wakeup the system from suspend on OMAP3430 EVM and SDP boards. The earlier approach of enabling wakeup on the touchscreen GPIO pin during board level mux init is removed. Instead the wakeup flag in ads7846_platform_data is enabled. Based on the flag, the ads7846 driver will do an enable_irq_wake which will eventually call into the OMAP GPIO layer and will enable the wakeup capability on the GPIO pin. Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
| * OMAP3EVM: Update pad configuration for wakeup enabled padsRanjith Lohithakshan2010-05-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | OMAP3530 TRM section 7.4.4.4.2 requires OFFOUTENABLE to be set (active low) if wakeup capabilities are enabled on a pad. During OFF mode testing on OMAP3530 EVM, it was observed that the device was not residing in the OFF state. The device enters into the OFF state and immediately exits from that state as if an IO wakeup event has occured. The issue was traced down to the pad configuration of wkaeup enabled pad's. Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* | usb: musb: Add extvbus in musb_board_dataAjay Kumar Gupta2010-05-201-0/+3
|/ | | | | | | | | | | EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA power so adding a flag which can be used by musb driver to program EXTVBUS. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* omap2/3/4: ehci: avoid compiler error with touchbookFelipe Balbi2010-03-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | the early_param() call in board-omap3touchbook.c expands to: static const char __setup_str_early_touchbook_revision[] __section(.init.rodata) _aligned(1) = tbr; [...] and we have a non-const variable being added to the same section: static struct ehci_hcd_omap_platform_data ehci_pdata __section(.init.rodata); because of that, gcc generates a section type conflict which can (and actually should) be avoided by marking const every variable marked with __initconst. This patch fixes that for the ehci_hdc_omap_platform_data. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: musb: Pass board specific data from board fileMaulik Mankad2010-02-191-1/+7
| | | | | | | | | | | | | | | | | | Pass board specific data for MUSB (like interface_type, mode etc) from board file by defining board specific structure. Each board file can define this structure based on its requirement and pass this information to the driver. Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <david-b@pacbell.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Gupta Ajay Kumar <ajay.gupta@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: musb: Remove #ifdef from board-omap3evm.cMaulik Mankad2010-02-191-2/+2
| | | | | | | | | | | This patch removes #ifdef around usb_nop_xceiv_register() from board-omap3evm.c Signed-off-by: Maulik Mankad <x0082077@ti.com> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: Configure GPIO175 for touchscreen PEN_IRQSanjeev Premi2010-02-171-1/+3
| | | | | | | | GPIO175 is used for PEN_IRQ on the EVM. This patch sets the mux settings for the same. Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: Fixes after moving to matrix_keypadSanjeev Premi2010-02-171-12/+15
| | | | | | | | | | | The keypad was not working properly after migrating to matrix_keypad. Swapped the row, col fields of the KEY() macro in the keymap definition to get it working again. Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: Add mux settings for keypadSanjeev Premi2010-02-171-0/+4
| | | | | | | | This patch sets SYS_NIRQ for keypad input. It also sets the same as a wakeup event from OFF mode. Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Rename hsmmc symbols to reflect independence from twl4030Adrian Hunter2010-02-151-2/+2
| | | | | | | | hsmmc.[ch] no longer has any dependency on twl4030 and variable names should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Rename mmc-twl4030 files to hsmmcAdrian Hunter2010-02-151-1/+1
| | | | | | | | mmc-twl4030.[ch] no longer has any dependency on twl4030 and should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap2/3/4: Fix omap2_map_common_io for multi-omapTony Lindgren2010-02-151-1/+1
| | | | | | Fix omap2_map_common_io for multi-omap Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP: Enable DSS2 for OMAP3EVM boardVaibhav Hiremath2010-02-121-11/+235
| | | | | | Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> [tomi.valkeinen@nokia.com: removed evm defconfig changes] Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
* mfd: twl: fix twl4030 rename for remaining driver, board filesBalaji T K2009-12-161-1/+1
| | | | | | | | | | | | | | | Recent drivers/mfd/twl4030* renames to twl broke compile for various boards as the series was missing a patch to change the board-*.c files. This patch renames include twl4030.h to include twl.h and also renames twl4030_i2c_ routines. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: mux: Remove old mux code for 34xxTony Lindgren2009-12-111-1/+0
| | | | | | Remove old mux code for 34xx Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: mux: Replace omap_cfg_reg() with new style signal or gpio functionsTony Lindgren2009-12-111-5/+5
| | | | | | Replace omap_cfg_reg() with new style signal or gpio functions Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: mux: Add new style init functions to omap3 board-*.c filesTony Lindgren2009-12-111-0/+10
| | | | | | | | | Add new style mux init functions to omap3 board-*.c files So far Beagle has been confirmed to be a CBB package, and CM-T35 a CUS package. Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: MIgrate to smsc911x ethernet driverSriram2009-11-221-13/+30
| | | | | | | | | | Migrate to smsc911x ethernet driver instead of smc911x driver. The smsc911x ethernet driver supports NAPI and performs better under heavy traffic. With the smc911x driver we were witnessing very high iowait time for high IO load over NFS. Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: Initialize vmmc and vmmc_aux regulatorsMike Rapoport2009-11-221-0/+51
| | | | | | | | | | | | Initialize vmmc and vmmc_aux regulators Note that the omap3evm_twldata.vmmc1 and omap3evm_twldata.vsim are set in omap3_evm_i2c_init() to avoid a merge conflict with the MFD tree. These will be initialized in omap3evm_i2c_boardinfo as a fix later on. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap3evm: ehci: Update EHCI support on OMAP3EVM (Rev >= E)Ajay Kumar Gupta2009-11-221-3/+26
| | | | | | | | | | | | | | | | | Added runtime programming for the differences in EHCI interface between OMAP3EVM revisions (Rev >= E) and (Rev < E). Changes: - EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E uses GPIO pin 135. - Rev >= E uses EHCI Vbus enable GPIO22 line. - Rev >= E uses GPIO61 to select EHCI port either on main board or on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have EHCI port on main board. - Currently GPIO61 it programmed to enable EHCI port on main board only. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
* omap3evm: Add board revision functionAjay Kumar Gupta2009-11-221-0/+35
| | | | | | | | | | | | | Added function to differentiate between the OMAP3EVM revisions. The chip-id of the ethernet PHY is being used for this purpose. Rev A to D : 0x01150000 Rev >= E : 0x92200000 Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Add platform init code for EHCI driverFelipe Balbi2009-11-221-0/+15
| | | | | | | | | | | | | | | | | | | | Add platform init code for EHCI driver. Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com> and Anand Gadiyar <gadiyar@ti.com>. Overo support added by Olof Johansson <olof@lixom.net> Beagle support added by Koen Kooi <koen@beagleboard.org> CM-T32 support added by Mike Rapoport <mike@compulab.co.il> Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Koen Kooi <koen@beagleboard.org> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP: Configure audio_mclk for twl4030-codec MFDPeter Ujfalusi2009-11-221-0/+1
| | | | | | | | | | audio_mclk value is going to be handled by the twl4030-codec MFD driver, configure the correct value for boards, which is using the twl4030 audio. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* OMAP: Platform support for twl4030_codec MFDPeter Ujfalusi2009-11-221-0/+9
| | | | | | | | | Add needed platform data for the twl4030_codec MFD on boards, where the audio part of the twl4030 codec is used. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Merge branch '7xx-iosplit-plat' with omap-fixesTony Lindgren2009-11-101-6/+6
|\
| * omap: headers: Move remaining headers from include/mach to include/platTony Lindgren2009-10-201-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: Tony Lindgren <tony@atomide.com>
| * omap: Fix DEBUG_LL UART io addressSantosh Shilimkar2009-10-191-1/+1
| | | | | | | | | | | | | | | | This patch fixes the low level debug UART io address as per this series. The change is essential to have CONFIG_DEBUG_LL working. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | omap: Fix omap-keypad by restoring old keypad.h without breaking omap2 ↵Janusz Krzysztofik2009-10-221-1/+1
|/ | | | | | | | | | | | | boards that use matrix_keypad Only mach-omap2 boards are currently using matrix_keypad. Allow mach-omap1 boards to use the old style keypad.h without breaking. Created against linux-2.6.32-rc5. Compile tested with omap_3430sdp_defconfig and rx51_defconfig. Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Fix matrix_keymap_data usageTony Lindgren2009-09-241-3/+7
| | | | | | | | | | Otherwise we'll get compile errors like: arch/arm/plat-omap/include/mach/keypad.h:38:1: warning: "KEY" redefined arch/arm/plat-omap/include/mach/keypad.h:39:1: warning: "PERSISTENT_KEY" redefined ... Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP2/3 board-*.c files: read bootloader configuration earlierPaul Walmsley2009-09-031-6/+6
| | | | | | | | | | | | | Most board-*.c files read configuration data from the bootloader in their .init_machine() function. This needs to happen earlier, at some point before omap2_init_common_hw() is called. This is because a future patch will use the bootloader serial console port information to enable the UART clocks earlier, immediately after omap2_clk_init(). This is in turn necessary since otherwise clock tree usecounts on clocks like dpll4_m2x2_ck will be bogus, which can cause the currently-active console UART clock to be disabled during boot. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP: UART: drop OMAP_TAG_UART, enable all UARTs, auto-disabled on idleKalle Valo2009-08-281-5/+0
| | | | | | | | | | | | | | | | OMAP tags are deprecrated so drop them. Drop UART config data which decides which UARTs to enable during boot. This is no longer necessary since serial core code disables clocks after inactivity. Background: with new UART idle code, all on-chip UARTs are idled using a configurable inactivity timer (default 5 seconds.) After the inactivity timer, UART clocks are disabled automatically. Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'omap_fixes_31' of git://git.pwsan.com/linux-2.6Russell King2009-08-101-1/+1
|\
| * OMAP3 SDRC: add support for 2 SDRAM chip selectsJean Pihet2009-07-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet <jpihet@mvista.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* | USB: musb: fix the nop registration for OMAP3EVMGupta, Ajay Kumar2009-08-071-0/+5
|/ | | | | | | | | | | | | | | | | | OMAP3EVM uses ISP1504 phy which doesn't require any programming and thus has to use NOP otg transceiver. Cleanups being done: - Remove unwanted code in usb-musb.c file - Register NOP in OMAP3EVM board file using usb_nop_xceiv_register(). - Select NOP_USB_XCEIV for OMAP3EVM boards. - Don't enable TWL4030_USB in omap3_evm_defconfig Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ARM: OMAP3: Add omap3 EVM supportSyed Mohammed Khasim2009-05-281-0/+329
Add omap3 EVM support Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
OpenPOWER on IntegriCloud