summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-mx5/board-mx53_evk.c
Commit message (Collapse)AuthorAgeFilesLines
* ARM i.MX: Merge i.MX5 support into mach-imxSascha Hauer2011-11-161-177/+0
| | | | | | | | | | This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx and adjusts the Makefile/Kconfig entries in a way that it's possible to compile i.MX5 together with i.MX3/6. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
* ARM i.MX5: remove unnecessary includes from board filesSascha Hauer2011-11-101-1/+0
| | | | Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'imx/devel' into next/dtArnd Bergmann2011-11-011-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | The board changes in the imx/devel branch conflict with other changes in the device imx/dt branch. Conflicts: arch/arm/mach-mx5/board-mx53_loco.c arch/arm/mach-mx5/board-mx53_smd.c arch/arm/plat-mxc/include/mach/common.h arch/arm/plat-mxc/include/mach/memory.h Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| * ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLERSascha Hauer2011-09-261-0/+1
| | | | | | | | | | | | Also, add handle_irq callbacks to machine descriptors. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | arm/mx5: add device tree support for imx53 boardsShawn Guo2011-10-181-2/+7
|/ | | | | | | | | It adds device tree support for imx53 boards. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5/mx53_evk: Add support for LEDFabio Estevam2011-07-071-0/+17
| | | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* gpio/mxc: Change gpio-mxc into an upstanding gpio driverShawn Guo2011-06-061-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The patch makes necessary changes on gpio-mxc as below to turn it into an upstanding gpio driver. * Add a list to save all mx2 ports references, so that mx2_gpio_irq_handler can walk through all interrupt status registers * Use readl/writel to replace mach-specific accessors __raw_readl/__raw_writel * Change mxc_gpio_init into mxc_gpio_probe function * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to be public at all, and also make some other cleanup on plat-mxc/include/mach/gpio.h at the same time And the patch then migrates mach-imx and mach-mx5 to the updated driver by adding corresponding platform devices. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* ARM: imx: remove #includes already available from devices-common.hUwe Kleine-König2011-05-191-2/+0
| | | | | | | | | | | | | | | | | Most machine files include "devices-imxXX.h" which in turn includes <mach/devices-common.h>. The latter already includes many headers that the machine files don't need to include again. These were found by: $ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile $ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F (but I kept linux/init.h, linux/kernel.h and linux/platform_device.h) LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5/mx53_evk: Make the reset pin name more meaningfulFabio Estevam2011-03-231-3/+3
| | | | | | | | | | | As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used on a MX53_EVK board. Change the pin name to reflect the board name. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5/mx53_evk: Use gpio_request_one in mx53_evk_fec_resetFabio Estevam2011-03-231-3/+2
| | | | | | | | | | | Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets the GPIO value via gpio_set_value right after. This is not needed. By using gpio_request_one it is possible to set the direction and initial value in one shot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5/mx53_evk: Fix IOMUX for UART3Fabio Estevam2011-03-071-3/+1
| | | | | | | On mx53_evk board only RX/TX pins are used on UART3. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mach-mx5: Add watchdog support for MX53 based boardsFabio Estevam2011-02-181-0/+1
| | | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5: use .init_early to initialize cpu type, reset address and iomuxerUwe Kleine-König2011-02-101-1/+2
| | | | | | | | This used to be done in .map_io which is supposed to only setup the memory mapping. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx5/board-mx53_evk.c: Make UART1 functionalFabio Estevam2011-02-011-3/+1
| | | | | | | Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: i.MX53: Add full iomux support for mx53Dinh Nguyen2011-01-211-18/+18
| | | | | | | | This iomux file contains all the available pins that are iomux capable. Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: i.MX53 EVK: add spi nor deviceYong Shen2011-01-131-0/+15
| | | | | | | add spi board information for spi nor device Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: i.MX53 EVK: add ecspi IOMUX settingYong Shen2011-01-131-2/+10
| | | | | | | add ecspi IOMUX setting, also fix a bug of chip select pin order Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX53 enable spi on EVK boardYong Shen2011-01-111-0/+14
| | | | | | | | | 1. some macro definitions fix 2. add platform data for spi device 3. register spi clocks Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX53 enable sdhc support on EVK boardYong Shen2011-01-071-0/+3
| | | | | | | | 1. changes some register address to fit macro definition 2. add platform data and clock for sdhc Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX53 enable i2c on EVK boardYong Shen2011-01-071-0/+7
| | | | | | | add i2c platform data and clock Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX53: enable fec driver on EVK boardYong Shen2011-01-071-0/+27
| | | | | | | | 1. Adjust FEC base address name to fit macro definition 2. Add platform data and reset function for FEC Signed-off-by: Yong Shen <yong.shen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM i.MX53: Make MX53 EVK bootableYong Shen2011-01-041-0/+84
1. Add entries to Kconfig 2. Add machine definition 3. Add Uart platform data, pad setting and base address 4. Adjust GPIO irq number Signed-off-by: Yong Shen <yong.shen@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
OpenPOWER on IntegriCloud