summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/omap3-evm-common.dtsi
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: add wl12xx/wl18xx bindingsEliad Peller2015-03-241-0/+10
| | | | | | | | | | | | | Replace all the pdata-quirks for setting wl12xx/wl18xx platform data with proper DT definitions. Signed-off-by: Eliad Peller <eliad@wizery.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com> Tested-by: Nikita Kiryanov <nikita@compulab.co.il> Tested-by: Tony Lindgren <tony@atomide.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Add twl keypad map for omap3 EVMTony Lindgren2014-11-051-0/+21
| | | | | | | | | | | | | | | Looks like we're still missing the keypad map for EVM. Let's add it since we have the binding now available for the twl4030_keypad as otherwise we get the following errors during the boot: twl4030_keypad keypad.31: OF: linux,keymap property not defined in /ocp/i2c@48070000/twl@48/keypad twl4030_keypad keypad.31: Failed to build keymap twl4030_keypad: probe of keypad.31 failed with error -2 Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Enable twl4030 off-idle configuration for selected omapsTony Lindgren2014-06-161-0/+7
| | | | | | | | | | | | | | | | | | N900 now seems to shut down the external oscillator when hitting off-idle. And Beagle XM seems to have OSC_EN pin connected to allow shutting down the oscillator looking at the schematics. The oscillator output is cut off in off-idle and you can monitor it from R56 on the bottom side of the board near the power jack. Note that for beagle we need to also enable the UART wake-up event, the others have that enabled in earlier patches. OMAP37XX EVM (TMDSEVM3730) does not seem to have twl4030 clken pin connected, so there is no point trying to enable shutting down of the oscillator on it for the extra latency it adds. Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldpTony Lindgren2014-06-031-0/+26
| | | | | | | | | | | | | | | | | Looks like quite a few omap3 boards have sharp ls037v7dw01 that's configured as various panel dpi entries for whatever legacy reasons. For device tree based support, let's just configure these properly for panel ls037v7dw01 instead of panel dpi. This patch creates a common file for panel ls037v7dw01, and makes boards ldp and omap3-evm to use it. The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen controller for the omaps, so let's add a basic configuration for the touchscreen also using the default values. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* Merge tag 'dt-for-linus' of ↵Linus Torvalds2013-11-111-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC DT updates from Olof Johansson: "Most of this branch consists of updates, additions and general churn of the device tree source files in the kernel (arch/arm/boot/dts). Besides that, there are a few things to point out: - Lots of platform conversion on OMAP2+, with removal of old board files for various platforms. - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well - Some updates to pinctrl and other subsystems. Most of these are for DT-enablement of the various platforms and acks have been collected" * tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits) ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx) ARM: dts: bcm281xx: Add card detect GPIO ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt) ARM: bcm281xx: Add device node for the GPIO controller ARM: mvebu: Add Netgear ReadyNAS 104 board ARM: tegra: fix Tegra114 IOMMU register address ARM: kirkwood: add support for OpenBlocks A7 platform ARM: dts: omap4-panda: add DPI pinmuxing ARM: dts: AM33xx: Add RNG node ARM: dts: AM33XX: Add hwspinlock node ARM: dts: OMAP5: Add hwspinlock node ARM: dts: OMAP4: Add hwspinlock node ARM: dts: use 'status' property for PCIe nodes ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts ARM: mvebu: Add the core-divider clock to Armada 370/XP ...
* ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)Tony Lindgren2013-10-141-0/+34
| | | | | | | | | | | | | | | I've tested the serial, MMC, smsc911x, wl12xx, and off-idle support with the pinctrl patches, so it probably works better than the board-*.c files ever did. Also the board-omap3evm.c file is broken for the DSS, and has been for a while. Patches are welcome to fix it in this .dts file, let's just drop the board-*.c file for this. Note that off-idle currently requires doing request_irq() on the wake-up pin from pinctrl-single IRQ domain until we can handle that in some Linux generic way. [tony@atomide.com: updated for make dtbs build fix] Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: Add common support for omap3-evmTony Lindgren2013-10-141-0/+60
Looks like the main difference between the TMDSEVM3530 and TMDSEVM3730 is just the omap processor: http://www.ti.com/tool/tmdsevm3530 http://www.ti.com/tool/tmdsevm3730 So let's add a common file for the EVMs, and fix the description for the omap3-evm.dst as that's clearly for the TMDSEVM3530 since it includes omap34xx.dtsi. It cannot support the TMDSEVM3730 properly, and we need a separate file for that in the following patch. Signed-off-by: Tony Lindgren <tony@atomide.com>
OpenPOWER on IntegriCloud