| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Looks like we have wrong GPMC timings we have for the cm-t and
sbc-t boards. This can cause occasional strange errors with at
least doing an rsync of large files or doing apt-get dist-upgrade.
Let's fix the issue in two phases. First let's simplify cm-t and
sbc-t to use the shared omap-gpmc-smsc911x.dtsi to avoid fixing
the issue in multiple places. Then we can fix the timings in
a single place with a follow-up patch.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Looks like the OTG pins are off by 2 and we get this:
pinctrl-single 48002030.pinmux: pin 480021a0.0 already requested by 49020000.serial; cannot claim for 480ab000.usb_otg_hs
pinctrl-single 48002030.pinmux: pin-184 (480ab000.usb_otg_hs) status -22
pinctrl-single 48002030.pinmux: could not request pin 184 (480021a0.0) from group pinmux_hsusb0_pins on device pinctrl-single
musb-omap2430 480ab000.usb_otg_hs: Error applying setting, reverse things back
That's probably because the TRM lists the values as
32-bit registers so every second needs 2 added to the
address. The OTG pin start range must start from
0x21a2, not 0x21a0.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
| |
Add USB OTG support for cm-t3x30 CoMs.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
| |
Add HS USB Host support along with USB PHYs and power supply regulators
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
| |
Add pullup for twl4030 GPIO_0 used as MMC1 card detect signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.
No functional changes.
The device tree will have the following structure:
omap3-cm-t3x.dtsi
|
|<-- omap3-cm-t3x30.dtsi
| |
| |
| | ----- ------- ------------
| | | CoM | | Board | | Base board |
| | ----- ------- ------------
| | omap3-sb-t35.dtsi
| | |
| |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
| | |
| |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
| |
|<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
This adds support for CompuLab SBC-T3530, also known as cm-t3730:
http://compulab.co.il/products/sbcs/sbc-t3530/
It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:
http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/
So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.
I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.
Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.
Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
