| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Documentation/blockdev/nbd.txt contained some documentation which was
horribly outdated and probably still dates from the original patch that
added NBD support to the kernel.
This patch removes the useless and outdated bits. The tools on nbd.sf.net
are fully documented in manpages, which is where documentation for the
non-kernel bits should live.
Additionally, add a reference to the MAINTAINERS file for the nbd-general
mailinglist that is used for discussion of the userland tools and the
kernel module already.
Signed-off-by: Wouter Verhelst <w@uter.be>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A long time ago, probably in 2002, one of the distros, or maybe more than
one, loaded block drivers prior to loading the SCSI mid layer. This meant
that the cciss driver, being a block driver, could not engage the SCSI mid
layer at init time without panicking, and relied on being poked by a
userland program after the system was up (and the SCSI mid layer was
therefore present) to engage the SCSI mid layer.
This is no longer the case, and cciss can safely rely on the SCSI mid
layer being present at init time and engage the SCSI mid layer straight
away. This means that users will see their tape drives and medium
changers at driver load time without need for a script in /etc/rc.d that
does this:
for x in /proc/driver/cciss/cciss*
do
echo "engage scsi" > $x
done
However, if no tape drives or medium changers are detected, the SCSI mid
layer will not be engaged. If a tape drive or medium change is later
hot-added to the system it will then be necessary to use the above script
or similar for the device(s) to be acceesible.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
| |
|
|
|
|
| |
Signed-off-by: Joseph Handzik <joseph.t.handzik@beardog.cce.hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Change all "arch/i386" to "arch/x86" in Documentaion/,
since the directory has changed.
Also update the files which have changed their filename
in the meantime accordingly.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
[jkosina@suse.cz: reword changelog]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive. Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2. This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| |
|
|
|
| |
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
|
Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
|
