summaryrefslogtreecommitdiffstats
path: root/Documentation/blackfin
Commit message (Collapse)AuthorAgeFilesLines
* Blackfin: spi-docs: further clarify GPIO CS behavior with various modesMike Frysinger2011-07-231-0/+2
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: document SPI CS limitations with CPHA=0Michael Hennerich2010-08-062-1/+18
| | | | | | | | | | | | With the Blackfin on-chip SPI peripheral, there is some logic tied to the CPHA bit whether the Slave Select Line is controlled by hardware (CPHA=0) or controlled by software (CPHA=1). However, the Linux SPI bus driver assumes that the Slave Select being asserted during the entire SPI transfer. So explain these small details for people who need certain SPI modes with standard CS behavior. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: remove useless and outdated documentationMichael Hennerich2010-08-063-230/+0
| | | | | | | | The filesystem and cache files duplicate existing & better documents, and these contain outdated information. So punt them. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Documentation/: it's -> its where appropriateFrancis Galiegue2010-04-231-1/+1
| | | | | | | | Fix obvious cases of "it's" being used when "its" was meant. Signed-off-by: Francis Galiegue <fgaliegue@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* Blackfin: add an example showing how to use the gptimers APIMike Frysinger2009-12-152-0/+89
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: punt cache lock documentationMichael Hennerich2009-12-153-61/+0
| | | | | | | The cache lock code was unused and punted, so punt the documentation too. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin arch: Add document about bfin-gpioGraf Yang2009-01-072-0/+74
| | | | | | | | | Add document about bfin-gpio when requesting a pin both as gpio and gpio interrupt. Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: add supporting for kgdbSonic Zhang2008-10-131-155/+0
| | | | | | Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* Blackfin arch: kgdb specific codeSonic Zhang2007-06-291-0/+155
| | | | | | Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* blackfin architectureBryan Wu2007-05-074-0/+293
This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OpenPOWER on IntegriCloud