summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: Use the HT capabilities from the IE instead of the station's caps.Sujith2008-11-251-1/+1
| | | | | | Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: make DMA memory consistentLuis R. Rodriguez2008-11-251-2/+11
| | | | | | | | | | | | | Make the DMAable mameory consistent with pci_set_consistent_dma_mask(). The DMA-mapping.txt Documentation recommends this but for PCI-X considerations and on strange architecture like SGI SN2, not sure why it would fix an issue but lets see if it does, just in case. Before this, this driver was tested with x86_64 with about 7 GB of RAM, not sure if this is really needed. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Clarify we only want 32-bit DMALuis R. Rodriguez2008-11-251-3/+2
| | | | | | | | | Use DMA_32BIT_MASK to clarify we only want 32-bit DMA memory. What was there before is also 32-bit but this makes it clearer Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Detect USB BULK in/out endpointsIvo van Doorn2008-11-255-28/+111
| | | | | | | | | | | | | | | | | | | | | | Instead of hardcoding the used in/out endpoints we should detect them by walking through all available endpoints. rt2800usb will gain the most out of this, because the legacy drivers indicate that there are multiple endpoints available. However this code might benefit at least rt73usb as well for the MIMO queues, and if we are really lucky rt2500usb will benefit because for the TX and PRIO queues. Even if rt2500usb and rt73usb do not get better performance after this patch, the endpoint detection still belongs to rt2x00usb, and it shouldn't hurt to always try to detect the available endpoints. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rtl8187: Remove module warning and dependence on CONFIG_EXPERIMENTALLarry Finger2008-11-252-4/+2
| | | | | | | | | | | | After considerable testing, the initial fears that the driver might damage some flavors of RTL8187B hardware seem to be groundless. Accordingly, the logged warning is removed. In addition, Kconfig is changed to remove the dependence on EXPERIMENTAL. Signed-off-by: Larry Finger <Larry.Finger@lwfinger> Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rtl8187: feedback transmitted packets using tx close descriptor for 8187BHerton Ronaldo Krzesinski2008-11-252-4/+136
| | | | | | | | | | | | | | Realtek 8187B has a receive command queue to feedback beacon interrupt and transmitted packet status. Use it to feedback mac80211 about status of transmitted packets. Unfortunately in the course of testing I found that the sequence number reported by hardware includes entire sequence control in a 12 bit only field, so a workaround is done to check only lowest bits. Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rtl8187: implement conf_tx callback to configure tx queuesHerton Ronaldo Krzesinski2008-11-253-12/+69
| | | | | | | | | Add conf_tx callback and use it to configure tx queues of 8187L/8187B. Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rtl8187: fix 8187B throughput regressionHerton Ronaldo Krzesinski2008-11-251-1/+1
| | | | | | | | | | | | | Hin-Tak Leung reported that after the change "rtl8187: add short slot handling for 8187B" his RTL8187B started to give low throughput on network transfers. Turns out that the SIFS setting used isn't ok, it doesn't look to be the real aSIFSTime, using the "magical" 0x22 value like on other 818x variants as the vendor does too fixes the issue. Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Race condition in accessing TX and RX buffers.Senthil Balasubramanian2008-11-251-15/+14
| | | | | | | | | | | | | | | | Race condition causes RX buffers to be accessed even before it is initialized. The RX and TX buffers are initialized immediately after the hardware is registered with mac80211. The mac80211 start callback is ready to be fired once the device is registered for a case when the wpa_supplicant is also running at the same time. The same race condition is also possible for RKFILL registration as RFKILL init happens after the device registration with mac80211 and it is possible that rfkill_register would be called even before it is initialized. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: IRQ should be disabled before calling free_irq()Senthil Balasubramanian2008-11-251-1/+1
| | | | | | | | ath9k frees irq even before IRQs are disabled and existing IRQs are flushed when rfkill_register() fails. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Build RFKILL feature even when RFKILL subsystem is a MODULESenthil Balasubramanian2008-11-254-11/+11
| | | | | | | | | Currently, ath9k builds RFKILL feature only when the RFKILL subsystem is built part of the kernel. Build RFKILL feature regardless of whether RFKILL subsystem is built as a MODULE or part of the kernel. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: incorrect noise floor threshold values.Senthil Balasubramanian2008-11-252-4/+4
| | | | | | | This patch fixes incorrect noise floor threshold values. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: INI update for atheros chipets.Senthil Balasubramanian2008-11-254-205/+586
| | | | | | | init values update for various atheros chipsets. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: enable custom fw regulatory solutionLuis R. Rodriguez2008-11-252-0/+5
| | | | | | | | | | | | | | This enables the custom firmware regulatory solution option on iwlwifi drivers. These devices are uncapable of mapping their EEPROM regulatory domain to a specific ISO / IEC alpha2. Although the new 11n devices (>= iwl 5000) have only 3 regultaory SKUs -- MOW, ABG (no N) and BG -- the older devices (3945 and 4965) have a more complex SKU arrangement and therefore its not practical to move this to the driver. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: add support for custom firmware regulatory solutionsLuis R. Rodriguez2008-11-252-1/+19
| | | | | | | | | | | | | This adds API to cfg80211 to allow wireless drivers to inform us if their firmware can handle regulatory considerations *and* they cannot map these regulatory domains to an ISO / IEC 3166 alpha2. In these cases we skip the first regulatory hint instead of expecting the driver to build their own regulatory structure, providing us with an alpha2, or using the reg_notifier(). Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211/mac80211: Add 802.11d supportLuis R. Rodriguez2008-11-259-24/+591
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds country IE parsing to mac80211 and enables its usage within the new regulatory infrastructure in cfg80211. We parse the country IEs only on management beacons for the BSSID you are associated to and disregard the IEs when the country and environment (indoor, outdoor, any) matches the already processed country IE. To avoid following misinformed or outdated APs we build and use a regulatory domain out of the intersection between what the AP provides us on the country IE and what CRDA is aware is allowed on the same country. A secondary device is allowed to follow only the same country IE as it make no sense for two devices on a system to be in two different countries. In the case the AP is using country IEs for an incorrect country the user may help compliance further by setting the regulatory domain before or after the IE is parsed and in that case another intersection will be performed. CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA present. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: mark regdomains with > NL80211_MAX_SUPP_REG_RULES invalidLuis R. Rodriguez2008-11-251-0/+3
| | | | | | | | | Lets remain consistent and mark rds with > NL80211_MAX_SUPP_REG_RULES number of reg rules as invalid in is_valid_rd(). Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: call_crda() won't tell us if CRDA was presentLuis R. Rodriguez2008-11-251-8/+1
| | | | | | | | | | | | | | | | | | | | | | kobject_uevent_env() can return an error but it just tells us if the uvent was built/sent or not, it doesn't tell us anything about what happened in userspace, whether the udev rule was present nor does it tell us if CRDA was present or not. So remove the informative complaint about it assuming it will tell us such things. Note that you can determine if CRDA is present after loading cfg80211 by using: is_old_static_regdom(cfg80211_regdomain) but this doesn't account for possible user install after initial boot, and also for when the user uses the static EU regulatory domain. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: expect different rd in cfg80211 when intersectingLuis R. Rodriguez2008-11-251-2/+3
| | | | | | | | | | When intersecting it is possible that set_regdom() was called with a regulatory domain which we'll only use as an aid to build a final regulatory domain. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: separate intersection section in __set_regdom()Luis R. Rodriguez2008-11-251-8/+21
| | | | | | | | | | | | | So far the __set_regdom() code is pretty generic as the intersection case is fairly straight forward; this will however change when 802.11d support is added so lets separate intersection code for now in preparation for 802.11d support. This patch only has slight functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: remove switch from __set_regdom()Luis R. Rodriguez2008-11-251-15/+6
| | | | | | | | | | | We have control over the REGDOM_SET_BY_* macros passed so remove the switch. This patch has no functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: remove switch from __regulatory_hint()Luis R. Rodriguez2008-11-251-26/+17
| | | | | | | | | | | | | | We have complete control over REGDOM_SET_BY_* enum passed down to __regulatory_hint() as such there is no need to account for unexpected REGDOM_SET_BY_*'s, lets just remove the switch statement as this code does not change and won't change even when we add 802.11d support. This patch has no functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: mark negative frequencies as invalidLuis R. Rodriguez2008-11-251-1/+1
| | | | | | | | | Regulatory rules with negative frequencies are now marked as invalid in is_valid_reg_rule(). Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: iwl-fh.h cleanupTomas Winkler2008-11-251-24/+17
| | | | | | | | | | This patch fix value of upper FH register bound plus it reorders and groups registers in more readable way Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: some fh document fix and cleanupZhu, Yi2008-11-252-9/+4
| | | | | | | | | | This patch cleans up some flow handler related document. It also removes some blank lines. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: configure_filter rewriteZhu, Yi2008-11-254-59/+70
| | | | | | | | | | | | | The patch rewrites the mac80211 configure_filter handler to better mapping mac80211 filter flags to iwlwifi hardware filter flags. We now can support 5 mac80211 filter flags: FIF_OTHER_BSS, FIF_ALLMULTI, FIF_PROMISC_IN_BSS, FIF_BCN_PRBRESP_PROMISC and FIF_CONTROL. This patch also avoids reconnecting if the filter flags are changed when the STA is associated. Because rx_assoc is used when full rxon is not necessary. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi : fix checkpatch.pl errorsAbhijeet Kolekar2008-11-259-12/+13
| | | | | | | | Patch fixes checkpatch.pl errors for iwlwifi. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: replace magic constants with defineChatre, Reinette2008-11-252-4/+4
| | | | | | | | | use IWL_CCK_RATES_MASK and IWL_OFDM_RATES_MASK instead of their values directly. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> cc: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: rs: remove fc variable and other cleanupsTomas Winkler2008-11-251-29/+19
| | | | | | | | | | | This patch 1. Removes use once use only fc variables, they are useless after refactoring ieee80211 frame control handlers 2. Other trivial cleanups Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: consolidate station management codeTomas Winkler2008-11-258-132/+148
| | | | | | | | | | | This patch moves code around and group most of the station management code into iwl-sta.c No functional changes (yet) Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwl3945 : Simplify iwl3945_pci_probeKolekar, Abhijeet2008-11-251-78/+117
| | | | | | | | | Patch aligns iwl3945_pci_probe with iwlwifi's iwl_pci_probe. Added few comments and code simplified to make readable. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix TX failure pathIvo van Doorn2008-11-252-10/+7
| | | | | | | | | | | | | | | | | | | | | The callback function write_tx_data() can only fail when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry failed to determine the entry was not available and it is in fact still owned by the hardware. This means that if that function fails the queue must be stopped in mac80211. When rt2x00queue_get_queue() returns NULL in the TX path, it means mac80211 has passed us an invalid queue, although this should be impossible, it shouldn't hurt if we send mac80211 a signal to stop the queue either. Both issues can simply be resolved by removing their manual failure handler and making them use the failure path provided in rt2x00mac_tx(). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Move rt73usb register access wrappers into rt2x00usbIvo van Doorn2008-11-253-201/+280
| | | | | | | | | | | | | rt2500usb and rt73usb have different register word sizes, for that reason the register access wrappers were never moved into rt2x00usb. With rt2800usb on its way, we should favor the 32bit register access and move those wrappers into rt2x00usb. That saves duplicate code, since only rt2500usb will need the special 16bit wrappers. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Cleanup indirect register accessIvo van Doorn2008-11-257-431/+310
| | | | | | | | | | | | | | All code which accessed indirect registers was similar in respect to the for-loop, the given timeout, etc. Move it into a seperate function, which for PCI drivers can be moved into rt2x00pci. This allows us to cleanup the cleanup the code further by removing the goto statementsand making the codepath look a bit nicer. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath5k: name pci driver "ath5k" tooJohannes Berg2008-11-251-1/+1
| | | | | | | | | Call the ath5k pci driver struct "ath5k" too to be less confusing in sysfs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Revert "hso: Fix crashes on close."David S. Miller2008-11-251-9/+2
| | | | | | | | This reverts commit 4a3e818181e1baf970e9232ca8b747e233176b87. On request from Alan Cox. Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "hso: Fix free of mutexes still in use."David S. Miller2008-11-251-87/+23
| | | | | | | | This reverts commit 52429eb216385fdc6969c0112ba8b46cffefaaef. On request from Alan Cox. Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "hso: Add TIOCM ioctl handling."David S. Miller2008-11-251-317/+12
| | | | | | | | This reverts commit 7ea3a9ad9bf360f746a7ad6fa72511a5c359490d. On request from Alan Cox. Signed-off-by: David S. Miller <davem@davemloft.net>
* xfrm: remove useless forward declarationsAlexey Dobriyan2008-11-252-4/+0
| | | | | Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ah4/ah6: remove useless NULL assignmentsAlexey Dobriyan2008-11-252-4/+0
| | | | | | | struct will be kfreed in a moment, so... Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: loopback bits not correctly cleared from RCTL registerAlexander Duyck2008-11-252-3/+4
| | | | | | | | | This change forces the bits to 0 by using an &= operation with an inverted mask of all options instead of using an |= with a value of 0. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: remove unneeded bit refrence when enabling jumbo framesAlexander Duyck2008-11-252-20/+6
| | | | | | | | | | There is a reference to a Buffer Size extention bit that is unneded by 82575/82576 hardware. Since it is not needed it should be removed from the code. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* DCB: fix kconfig optionJeff Kirsher2008-11-258-21/+31
| | | | | | | | | Since the netlink option for DCB is necessary to actually be useful, simplified the Kconfig option. In addition, added useful help text for the Kconfig option. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* aoe: remove private mac address format functionHarvey Harrison2008-11-255-25/+14
| | | | | | | Add %pm to omit the colons when printing a mac address. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Hook up ->reset_resumeDenis Joseph Barrow2008-11-251-0/+1
| | | | | | | | | | Made usb_drivers reset_resume function point to hso_resume this fixes problems a usb reset is done when the network interface is left idle for a few minutes. Possibly reset_resume should initialise hardware more but this works in the common case. Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Add TIOCM ioctl handling.Denis Joseph Barrow2008-11-251-12/+317
| | | | | | | | | Makes TIOCM ioctls for Data Carrier Detect & related functions work like /drivers/serial/serial-core.c potentially needed for pppd & similar user programs. Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Fix free of mutexes still in use.Denis Joseph Barrow2008-11-251-23/+87
| | | | | | | | | | | | | A new structure hso_mutex_table had to be declared statically & used as as hso_device mutex_lock(&serial->parent->mutex) etc is freed in hso_serial_open & hso_serial_close by kref_put while the mutex is still in use. This is a substantial change but should make the driver much stabler. Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Fix URB submission -EINVAL.Denis Joseph Barrow2008-11-251-11/+14
| | | | | | | | | Added check for IFF_UP in hso_resume, this should eliminate -EINVAL (-22) errors caused from urb's being submitted twice, once by hso_resume & once in hso_net_open, if suspend/resume USB power saving mode is enabled Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Fix crashes on close.Denis Joseph Barrow2008-11-251-2/+9
| | | | | | | | | | | | | | Moved serial_open_count in hso_serial_open to prevent crashes owing to the serial structure being made NULL when hso_serial_close is called even though hso_serial_open returned -ENODEV, Alan Cox pointed out this happens, also put in sanity check in hso_serial_close to check for a valid serial structure which should prevent the most reproducable crash in the driver when the hso device is disconnected while in use. Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hso: Add new usb device id's.Denis Joseph Barrow2008-11-251-0/+5
| | | | | Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud