summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* bcma: make bcma_find_core_unit() accessibleHauke Mehrtens2013-01-072-2/+4
| | | | | | | | This bcma_find_core_unit() is needed by the mips driver in the next patch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix calibration for AR9340Sujith Manoharan2013-01-071-1/+1
| | | | | | | | | | TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration is run as part of AGC calibration only for AR9485, AR9462 and AR9565. For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent of AGC-cal. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: bump firmware API to 3Yogesh Ashok Powar2013-01-071-1/+1
| | | | | | | | | | | | New firmware is required to support a) Add support for additional ampdu streams b) Handle corresponding watchdog events to destroy ampdu streams Bumping firmware API version by one. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: Handle watchdog event with highest prioriryYogesh Ashok Powar2013-01-071-0/+19
| | | | | | | | | | | | | | | | | | Currently, command path waits till all the tx host queues are empty. Whenever watchdog event is raised, firmware expects driver to destroy ampdu queues immediately. This requires corresponding commands i.e. mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be sent without waiting for the tx queues to be completely empty. Use "watchdog_event_pending" to ensure the above mentioned two commands are sent down immediately. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: Handle Watchdog events for the new ampdu streamsYogesh Ashok Powar2013-01-071-12/+32
| | | | | | | | | | | | | | | | With more ampdu streams, we need to handle watchdog events for the new ampdu streams. Handle these events appropriately. Earlier mwl8k_cmd_get_watchdog_bitmap used to return only one stream index and hence bitwise operations on the return value were not required. Now the function returns a bitmap with different bits are mapped with different stream indices. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: changing mwl8k_destroy_ba prototypeYogesh Ashok Powar2013-01-071-6/+8
| | | | | | | | | | | | Currently, mwl8k_ampdu_stream is passed as one of the argument to the function mwl8k_destroy_ba. Instead of this pass only the stream index. This will be helpful during watchdog event handling when bitmap of stream indices are received. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: Enable support to support additional ampdu streamsYogesh Ashok Powar2013-01-071-4/+27
| | | | | | | | | | Currently, we have 2 ampdu streams that can be created simultaneously. Firmware is capable of supporting additional streams. Add support to use these streams. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: set ack policy to normalYogesh Ashok Powar2013-01-071-0/+4
| | | | | | | | Set ACK policy to NORMAL when its not going to be an AMPDU packet. Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwl8k: Remove redundant txq_idxYogesh Ashok Powar2013-01-071-4/+2
| | | | | | | | | Ampdu stream index can be derived from stream->idx. So we no longer need stream->txq_idx, hence removing it. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Remove TEMP_COMP_CALSujith Manoharan2013-01-072-18/+3
| | | | | | | This is not enabled for any chip and is unused. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Enable calibration types in init_cal_settingsSujith Manoharan2013-01-072-13/+11
| | | | | | | | | Doing this in ath9k_hw_fill_cap_info() is odd and it's cleaner to do this in the init function for calibration. Also, setup the supported calibration type in init_cal_settings. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: parse WMM IEs from hostapd for mwifiex APAvinash Patil2013-01-076-7/+75
| | | | | | | | | | | This patch adds support for parsing WMM IEs from hostapd and setting them to FW via sys configure command. Patch also sets wiphy flag to advertise AP uAPSD support. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: use correct htcapinfo for HT20 ibss networkAmitkumar Karwar2013-01-072-1/+13
| | | | | | | | | | | It is observed that same htcapinfo ie is included in beacon for HT20, HT40+ and HT40- ibss networks. This patch makes sure that we will not advertise 40Mhz flags while creating/joining ibss network in HT20 mode. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: mwifiex: remove unreachable pathsSasha Levin2013-01-071-27/+3
| | | | | | | | | We know 'firmware' is non-NULL from the beginning of mwifiex_prog_fw_w_helper, remove all !firmware paths from the rest of the function. Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* p54pci: don't return zero on failure paths in p54p_probe()Alexey Khoroshilov2013-01-071-2/+5
| | | | | | | | | | | | | | If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(), it breaks off initialization, deallocates all resources, but returns zero. Similar issue is if check for returned value of pci_resource_len() fails. The patch implements proper error code propagation. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Update init code routines from interface up.Hante Meuleman2013-01-072-24/+15
| | | | | | | | | | | On interface up dongle gets inialized. Move UP command to common routine and update these common init routines using ifp. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Removing obsolete variables and inline functions.Hante Meuleman2013-01-072-26/+0
| | | | | | | | Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Return correct error on netdev xmit.Hante Meuleman2013-01-071-10/+12
| | | | | | | | | | | | | Netdev xmit routine brcfm_netdev_start_xmit was defined incorrectly and used wrong return codes. Always eat the packet and return ok. Remove drvr_up check since it is not relevant. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Remove unused caching dongle error.Hante Meuleman2013-01-072-23/+2
| | | | | | | | | | | CDC errors are retained. However, it is never used so it can be removed. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove unnecessary curly braces in dhd_attach()Arend van Spriel2013-01-071-2/+1
| | | | | | | | | | Stumbled into a curly braces used for if statement with only one conditional statement. Removing them. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: cleanup netdev transmit callbackArend van Spriel2013-01-071-9/+13
| | | | | | | | | | | The header of the ethernet packet is processed conditionally, but the check is wrong as it checks skb length is at least ETH_ALEN. It should check it is at least sizeof struct ethhdr instead. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove unused event related definitionsArend van Spriel2013-01-071-7/+0
| | | | | | | | | | | | The driver had some global definitions in dhd.h to map event identifiers to event names. With redesign of firmware event processing this has all moved to fweh module so these definitions can be removed. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Use dedicated trace level for CDC.Hante Meuleman2013-01-073-25/+24
| | | | | | | | | | | | CDC debug is partly done with TRACE and partly with CTL, however CDC hardly ever needs debugging. Use dedicated level CDC and replace TRACE and CTL in dhd_cdc with that. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove brcmf_proto_hdrpull() from bus interfaceArend van Spriel2013-01-076-43/+29
| | | | | | | | | | | The use of the function brcmf_proto_hdrpull() is moved to the common part of the driver and consequently it can be removed from the bus interface. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove rx helper function from bus interfaceArend van Spriel2013-01-074-16/+13
| | | | | | | | | | | | The bus interface provided a wrapper function to pass a single packet to the common driver part filling a skb queue with one packet. For clarity the caller now sets up the skb queue and call the rx bus interface function. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: define pr_fmt in one placeArend van Spriel2013-01-079-16/+4
| | | | | | | | | | | | Several source files (but not all) define the pr_fmt() macro in exactly the same way. Instead this commit defines it in a header file so driver logging is consistent. Cc: Joe Perches <joe@perches.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: assure USB dongle firmware is reset upon module unloadArend van Spriel2013-01-074-1/+27
| | | | | | | | | | | Upon unloading the brcmfmac module the USB firmware should be reset as the device remains powered. The reset assures a known device state when a new brcmfmac driver load is being done. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: removed deprecated set_bitrate_mask supportHante Meuleman2013-01-071-62/+0
| | | | | | | | | | | Set bitrate_mask is not desired anymore. The firmware will determine the correct rates to be used. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: do not reconfigure refill rx on 0-length packet.Hante Meuleman2013-01-071-1/+5
| | | | | | | | | | | | When USB device gets removed rx complete comes with 0-length packets. Do not refill those packets. In some rare cases it can cause infinite loop. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmsmac: remove dead codePiotr Haber2013-01-072-6/+2
| | | | | | | | | | | Dead code after AMPDU restructure. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmsmac: allow user-space setting of interface addressArend van Spriel2013-01-072-4/+4
| | | | | | | | | | | | The interface address of the wireless device is determined by the permanent address stored in the device. This patch allows it to be overridden from user-space. Reported-by: Maximilian Engelhardt <maxi@daemonizer.de> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmsmac: use perimeter lock in add_interface() callbackArend van Spriel2013-01-071-0/+2
| | | | | | | | | | | All callbacks that access driver functions should do that under perimeter lock protection. The add_interface() callback was lacking this lock. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmsmac: increase timer reference count for new timers onlyPiotr Haber2013-01-071-3/+4
| | | | | | | | | | | | | On hardware reintialization reference count of already existing timers would be increased again. This leads to problems on module unloading. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: rt2800: convert read_eeprom functions to return an int valueGabor Juhos2013-01-074-21/+43
| | | | | | | | | | | | | | | Both the rtt2x00usb_eeprom_read and the ioremap functions are allowed to fail, however their return values are not checked in the read_eeprom functions in the rt2800{pci,usb} drivers. The patch adds the missing checks, and converts all read_eeprom functions to return an int value, so the error values can be propagated up to the 'rt2800_validate_eeprom' function. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Remove AR9485 1.0 macroSujith Manoharan2013-01-071-3/+0
| | | | | Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmsmac: initialize morepending in brcms_b_recv()Geert Uytterhoeven2013-01-071-1/+1
| | | | | | | | | drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’: drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlegacy: allow to enable PSStanislaw Gruszka2013-01-072-3/+6
| | | | | | | | | | | Power save support was removed from iwlegacy due to possible firmware crashes problems it cause. I use to plan first inspect code to find reason of problems, fix them and then allow to enable PS. But realistically - code inspection will not happen, so let's do it, and wait for eventual bug reports. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlegacy: add flush callbackStanislaw Gruszka2013-01-074-0/+39
| | | | | | | | Dump implementation of flush, which just wait until all TX queues become empty. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix column header comments for some initval arraysGabor Juhos2013-01-072-6/+6
| | | | | | | | | | | | | | | | | Some 3-column initval arrays have wrong comments. The column of these arrays is indexed by the 'freqIndex' variable in 'ar5008_hw_process_ini' which only depends on the actual band. The 'initvals' tool from 'qca-swiss-army-knife' prints the correct comment lines for these arrays, since commit 'atheros-initvals: fix comments for non-fastclock 3-column tables' however the comments were not refreshed in ath9k. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: refactor carl9170_update_beaconChristian Lamparter2013-01-071-53/+80
| | | | | | | | | This patch moves parts of carl9170_update_beacon into separate subroutines, so the parts become more manageable. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: remove custom NUM_TID and friendsChristian Lamparter2013-01-072-14/+8
| | | | | | | | The commit: "mac80211: introduce IEEE80211_NUM_TIDS and use it" introduced a generic NUM_TID definitions for all everyone. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: disable hw crypto for p2p networksChristian Lamparter2013-01-071-0/+8
| | | | | | | | | | While the driver supports HW offload in a single P2P client configuration, it doesn't support HW offload in the concurrent P2P GO+CLIENT configuration. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: don't enable hw crypto offload, if the fw doesn't support itChristian Lamparter2013-01-073-12/+24
| | | | | | | | Previously, op_start would set disable_offload always to false, even if it was set to true by the fw parser. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: Only specify interface combinations if more than one interface is ↵Christian Lamparter2013-01-071-10/+19
| | | | | | | | | | | | | | | | | | possible Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c /* Combinations with just one interface aren't real */ if (WARN_ON(c->max_interfaces < 2)) Note: The number of supported interfaces is set by the carl9170 firmware. The default number of supported interfaces for all current firmwares is 2. Therefore this warning can only be observed with custom firmwares. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: allow P2P_GO interface creation after P2P_CLIENTChristian Lamparter2013-01-071-3/+51
| | | | | | | | | | | | | Janusz Dziedzic reported that after a change in wpa_supplicant ["nl80211: Automatically use concurrent P2P if possible"], carl9170 was no longer able to host a P2P network. This patch tackles the problem by allowing GO interfaces to be registered, long after the P2P_CLIENT interface is brought up. Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: import 1.9.7 firmware headersChristian Lamparter2013-01-073-4/+12
| | | | | | | | | | | Import new headers from my firmware branch: <https://github.com/chunkeey/carl9170fw> visit our wiki at: <http://wireless.kernel.org/en/users/Drivers/carl9170.fw> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* carl9170: advertise support for TDLSChristian Lamparter2013-01-072-5/+5
| | | | | | | | | | | Based on a quick test [ath9k and carl9170], TDLS seemed to be working fine. And while we are at it, let's move the wiphy feature flag set from carl9170_alloc into a single place in carl9170_fw. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: use the devres API for allocationsFelix Fietkau2013-01-077-80/+37
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: use the devres API for allocations/mappingsFelix Fietkau2013-01-077-170/+51
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: refactor RFCSR initializationStanislaw Gruszka2013-01-071-372/+423
| | | | | | | | | rt2800_init_rfcsr() is too big, split RF initialization into per chip functions. Code will change, but we should setup the same values onto RF registers and in the same order as before. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
OpenPOWER on IntegriCloud