summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* cxgb3 - fix skb->dev dereferenceDivy Le Ray2007-06-201-1/+1
| | | | | | | | eth_type_trans() now sets skb->dev. References to skb->dev should happen after it is called. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* natsemi irq flagsGregory Haskins2007-06-201-1/+1
| | | | | | | The spinlock irq flags should be a unsigned long to properly support 64 bit Signed-off-by: Gregory Haskins <ghaskins@novell.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* forcedeth: use unicast receive mode for WoLTim Mann2007-06-201-1/+3
| | | | | | | | | | | | | | | I happened to notice that a system with an NVidia NIC using the forcedeth driver won't wake-on-LAN if the interface was in promiscuous mode when you power off. By experiment, it looks like the hardware needs to have NvRegPacketFilterFlags set to NVREG_PFF_ALWAYS|NVREG_PFF_MYADDR (i.e., receive unicast packets to my address) in order for WoL to work. Jeff Garzik writes: "NVIDIA says the patch looks OK." I didn't venture to insert a signed-off-by line with his name on it, though. Signed-off-by: Tim Mann <mann@vmware.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: netiucv inlining cleanupMartin Schwidefsky2007-06-201-15/+3
| | | | | | | | | The recent iucv rework patches re-introduced some unnecessary inlines. Remove them again. Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: netiucv spinlock initializer cleanupThomas Gleixner2007-06-201-1/+1
| | | | | | | | spinlock initializer cleanup in netiucv.c Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: don't call iucv_path_connect from tasklet contextUrsula Braun2007-06-201-1/+2
| | | | | | | | | | | net/iucv/iucv.c creates the requirement for iucv_path_connect not to be called from tasklet context anymore. An extra checking is added in case of a failing netiucv_tx to fulfil this requirement for netiucv. Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: Use ccw_device_get_id() in qeth/claw driversCornelia Huck2007-06-202-14/+11
| | | | | | | | | Use ccw_device_get_id() to get a device number instead of parsing the ccw device's bus id. Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: qeth: wrong packet length in qdio headerFrank Pavlic2007-06-201-2/+1
| | | | | | | | | Packets Length in qdio header is broken when using EDDP on Layer2 devices. This leads to skb_under_panic on receiver system when running on z/VM GuestLAN devices. Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: avoid inconsistent lock state in qethUrsula Braun2007-06-201-4/+4
| | | | | | | | | | | | ipv6_regen_rndid in net/ipv6/addrconf.c makes use of "write_lock_bh" for its inet6_dev->lock. It may run in softirq-context. qeth makes use of "read_lock" for the same inet6_dev->lock. To avoid a potential deadlock situation, qeth should make use of "read_lock_bh" for its usages of inet6_dev->lock. Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: qeth driver does not recoverUrsula Braun2007-06-201-6/+6
| | | | | | | | | | | | While first recovery continues, the card issues a STARTLAN command itself. In this case qeth schedules another recovery. This second recovery is cancelled because of an already running first recovery. Stop first recovery in case of 0xe080. Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s390: print correct level for HiperSockets devicesUrsula Braun2007-06-201-9/+11
| | | | | | | | | For real HiperSockets the EBCDIC-ASCII conversion is not necessary. This is only needed for z/VM GuestLAN devices. Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* bonding: Fix 802.3ad no carrier on "no partner found" instanceJay Vosburgh2007-06-202-7/+6
| | | | | | | | | | | | | | | | | Modify carrier state determination for 802.3ad mode to comply with section 43.3.9 of IEEE 802.3, which requires that "Links that are not successful candidates for aggregation (e.g., links that are attached to other devices that cannot perform aggregation or links that have been manually configured to be non-aggregatable) are enabled to operate as individual IEEE 802.3 links." Bug reported by Laurent Chavey <chavey@google.com>. This patch is an updated version of his patch that changes the wording of commentary and adds an update to the driver version. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Laurent Chavey <chavey@google.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* bonding: Fix use after free in unregister pathJay Vosburgh2007-06-202-2/+2
| | | | | | | | | | | | | | | | The following patch (based on a patch from Stephen Hemminger <shemminger@linux-foundation.org>) removes use after free conditions in the unregister path for the bonding master. Without this patch, an operation of the form "echo -bond0 > /sys/class/net/bonding_masters" would trigger a NULL pointer dereference in sysfs. I was not able to induce the failure with the non-sysfs code path, but for consistency I updated that code as well. I also did some testing of the bonding /proc file being open while the bond is being deleted, and didn't see any problems there. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: checksum and ethtoolStephen Hemminger2007-06-202-20/+5
| | | | | | | | | | | | | It doesn't look like spidernet hardware can really checksum all protocols, the code looks like it does IPV4 only. If so, it should use NETIF_F_IP_CSUM instead of NETIF_F_HW_CSUM. The driver doesn't need it's own get/set for ethtool tx csum, and it should use the standard ethtool_op_get_link. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: turn off descriptor chain end interrupt.Linas Vepstas2007-06-201-2/+2
| | | | | | | | | | At some point, the transmit descriptor chain end interrupt (TXDCEINT) was turned on. This is a mistake; and it damages small packet transmit performance, as it results in a huge storm of interrupts. Turn it off. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: silence the ramfull messagesLinas Vepstas2007-06-202-9/+12
| | | | | | | | | | Although the previous patch resolved issues with hangs when the RX ram full interrupt is encountered, there are still situations where lots of RX ramfull interrupts arrive, resulting in a noisy log in syslog. There is no need for this. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: Don't terminate the RX ringLinas Vepstas2007-06-201-9/+9
| | | | | | | | | | | The terminated RX ring will cause trouble during the RX ram full conditions, leading to a hung driver, as the hardware can't find the next descr. There is no real reason to terminate the RX ring; it doesn't make the operation any smooother, and it does require an extra sync. So don't do it. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: Cure RX ram full bugLinas Vepstas2007-06-202-7/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a rare deadlock that can occur when the kernel is not able to empty out the RX ring quickly enough. Below follows a detailed description of the bug and the fix. As long as the OS can empty out the RX buffers at a rate faster than the hardware can fill them, there is no problem. If, for some reason, the OS fails to empty the RX ring fast enough, the hardware GDACTDPA pointer will catch up to the head, notice the not-empty condition, ad stop. However, RX packets may still continue arriving on the wire. The spidernet chip can save some limited number of these in local RAM. When this local ram fills up, the spider chip will issue an interrupt indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit will be set in GHIINT1STS). When te RX ram full condition occurs, a certain bug/feature is triggered that has to be specially handled. This section describes the special handling for this condition. When the OS finally has a chance to run, it will empty out the RX ring. In particular, it will clear the descriptor on which the hardware had stopped. However, once the hardware has decided that a certain descriptor is invalid, it will not restart at that descriptor; instead it will restart at the next descr. This potentially will lead to a deadlock condition, as the tail pointer will be pointing at this descr, which, from the OS point of view, is empty; the OS will be waiting for this descr to be filled. However, the hardware has skipped this descr, and is filling the next descrs. Since the OS doesn't see this, there is a potential deadlock, with the OS waiting for one descr to fill, while the hardware is waiting for a differen set of descrs to become empty. A call to show_rx_chain() at this point indicates the nature of the problem. A typical print when the network is hung shows the following: net eth1: Spider RX RAM full, incoming packets might be discarded! net eth1: Total number of descrs=256 net eth1: Chain tail located at descr=255 net eth1: Chain head is at 255 net eth1: HW curr desc (GDACTDPA) is at 0 net eth1: Have 1 descrs with stat=xa0800000 net eth1: HW next desc (GDACNEXTDA) is at 1 net eth1: Have 127 descrs with stat=x40800101 net eth1: Have 1 descrs with stat=x40800001 net eth1: Have 126 descrs with stat=x40800101 net eth1: Last 1 descrs with stat=xa0800000 Both the tail and head pointers are pointing at descr 255, which is marked xa... which is "empty". Thus, from the OS point of view, there is nothing to be done. In particular, there is the implicit assumption that everything in front of the "empty" descr must surely also be empty, as explained in the last section. The OS is waiting for descr 255 to become non-empty, which, in this case, will never happen. The HW pointer is at descr 0. This descr is marked 0x4.. or "full". Since its already full, the hardware can do nothing more, and thus has halted processing. Notice that descrs 0 through 254 are all marked "full", while descr 254 and 255 are empty. (The "Last 1 descrs" is descr 254, since tail was at 255.) Thus, the system is deadlocked, and there can be no forward progress; the OS thinks there's nothing to do, and the hardware has nowhere to put incoming data. This bug/feature is worked around with the spider_net_resync_head_ptr() routine. When the driver receives RX interrupts, but an examination of the RX chain seems to show it is empty, then it is probable that the hardware has skipped a descr or two (sometimes dozens under heavy network conditions). The spider_net_resync_head_ptr() subroutine will search the ring for the next full descr, and the driver will resume operations there. Since this will leave "holes" in the ring, there is also a spider_net_resync_tail_ptr() that will skip over such holes. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* spidernet: null out skb pointer after its been used.Linas Vepstas2007-06-201-0/+1
| | | | | | | | | | | | Avoid kernel crash in mm/slab.c due to double-free of pointer. If the ethernet interface is brought down while there is still RX traffic in flight, the device shutdown routine can end up trying to double-free an skb, leading to a crash in mm/slab.c Avoid the double-free by nulling out the skb pointer. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2007-06-203-15/+27
|\ | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: Only set client->iso_context if allocation was successful. ieee1394: fix to ether1394_tx in ether1394.c firewire: fix hang after card ejection
| * firewire: Only set client->iso_context if allocation was successful.Kristian Høgsberg2007-06-211-8/+11
| | | | | | | | | | | | | | | | This patch fixes an OOPS on cdev release for an fd where iso context creation failed. Signed-off-by: Kristian Høgsberg <krh@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: fix to ether1394_tx in ether1394.cCarlos E. Ugarte2007-06-161-6/+15
| | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a problem that occurs when packets cannot be sent across the ieee1394 bus and we return NETDEV_TX_BUSY in the net driver "hard start xmit" routine ether1394_tx. When we return NETDEV_TX_BUSY the stack will call ether1394_tx again with the same skb. So we need to restore the header to look like it did before we munged it for xmit over ieee1394. [Stefan Richter: changed whitespace, deleted a local variable] Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * firewire: fix hang after card ejectionStefan Richter2007-06-161-1/+1
| | | | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
* | Merge branch 'for-linus' of ↵Linus Torvalds2007-06-2011-138/+259
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/mlx4: Make sure inline data segments don't cross a 64 byte boundary IB/mlx4: Handle FW command interface rev 3 IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean() IB/mlx4: Get rid of max_inline_data calculation IB/mlx4: Handle new FW requirement for send request prefetching IB/mlx4: Fix warning in rounding up queue sizes IB/mlx4: Fix handling of wq->tail for send completions
| * | IB/mlx4: Make sure inline data segments don't cross a 64 byte boundaryRoland Dreier2007-06-182-3/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Inline data segments in send WQEs are not allowed to cross a 64 byte boundary. We use inline data segments to hold the UD headers for MLX QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that is too big to fit in a single inline data segment without crossing a 64 byte boundary, so split the header into two inline data segments. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Handle FW command interface rev 3Roland Dreier2007-06-187-87/+121
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Upcoming firmware introduces command interface revision 3, which changes the way port capabilities are queried and set. Update the driver to handle both the new and old command interfaces by adding a new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware interface revision and then using the correct interface based on the setting of the flag. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean()Jack Morgenstein2007-06-181-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When compacting CQ entries, we need to set the correct value of the ownership bit in case the value is different between the index we copy the CQE from and the index we copy it to. Found by Ronni Zimmerman of Mellanox. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Get rid of max_inline_data calculationRoland Dreier2007-06-181-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The calculation of max_inline_data in set_kernel_sq_size() is bogus, since it doesn't take into account the fact that inline segments may not cross a 64-byte boundary, and hence multiple inline segments will probably need to be used to post large inline sends. We don't support inline sends for kernel QPs anyway, so there's no point in doing this calculation anyway, since the field is just zeroed out a little later. So just delete the bogus calculation. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Handle new FW requirement for send request prefetchingRoland Dreier2007-06-185-38/+83
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | New ConnectX firmware introduces FW command interface revision 2, which requires that for each QP, a chunk of send queue entries (the "headroom") is kept marked as invalid, so that the HCA doesn't get confused if it prefetches entries that haven't been posted yet. Add code to the driver to do this, and also update the user ABI so that userspace can request that the prefetcher be turned off for userspace QPs (we just leave the prefetcher on for all kernel QPs). Unfortunately, marking send queue entries this way is confuses older firmware, so we change the driver to allow only FW command interface revisions 2. This means that users will have to update their firmware to work with the new driver, but the firmware is changing quickly and the old firmware has lots of other bugs anyway, so this shouldn't be too big a deal. Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Fix warning in rounding up queue sizesRoland Dreier2007-06-121-2/+2
| | | | | | | | | | | | | | | | | | | | | Doing max(1, foo) where foo is u32 generates a warning, because 1 is a signed constant. Fix this by using 1U instead. Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * | IB/mlx4: Fix handling of wq->tail for send completionsRoland Dreier2007-06-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cast the increment added to wq->tail when send completions are processed to u16 to avoid using wrong values caused by standard integer promotions. The same bug was fixed in libmlx4 by Eli Cohen <eli@mellanox.co.il>. Signed-off-by: Roland Dreier <rolandd@cisco.com>
* | | Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds2007-06-2016-86/+73
|\ \ \ | | | | | | | | | | | | | | | | * 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Don't drag a platform specific header into generic arch code.
| * | | [MIPS] Don't drag a platform specific header into generic arch code.Ralf Baechle2007-06-2016-86/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For some platforms it's definitions may conflict. So that's the one-liner. The rest is 10 square kilometers of collateral damage fixup this include used to paper over. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* | | | Merge branch 'merge' of ↵Linus Torvalds2007-06-202-3/+5
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix powermac late initcall to only run on powermac [POWERPC] PowerPC: Prevent data exception in kernel space (32-bit)
| * | | | [POWERPC] Fix powermac late initcall to only run on powermacTony Breeds2007-06-201-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current ppc64_defconfig kernel fails to boot on iSeries, dying with: Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc00000000071b258 Oops: Kernel access of bad area, sig: 11 [#1] SMP NR_CPUS=32 iSeries <snip> NIP [c00000000071b258] .iSeries_src_init+0x34/0x64 LR [c000000000701bb4] .kernel_init+0x1fc/0x3bc Call Trace: [c000000007d0be30] [0000000000008000] 0x8000 (unreliable) [c000000007d0bea0] [c000000000701bb4] .kernel_init+0x1fc/0x3bc [c000000007d0bf90] [c0000000000262d4] .kernel_thread+0x4c/0x68 Instruction dump: e922cba8 3880ffff 78840420 f8010010 f821ff91 60000000 e8090000 78095fe3 4182002c e922cb58 e862cbb0 e9290140 <e8090000> f8410028 7c0903a6 e9690010 Kernel panic - not syncing: Attempted to kill init! This happens because some powermac code unconditionally sets ppc_md.progress to NULL. This patch makes sure the powermac late initcall is only run on powermac machines. Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * | | | [POWERPC] PowerPC: Prevent data exception in kernel space (32-bit)Segher Boessenkool2007-06-201-3/+2
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "is_exec" branch of the protection check in do_page_fault() didn't do anything on 32-bit PowerPC. So if a userland program jumps to a page with Linux protection flags "---p", all the tests happily fall through, and handle_mm_fault() is called, which in turn calls handle_pte_fault(), which calls update_mmu_cache(), which goes flush the dcache to a page with no access rights. Boom. This fixes it. Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
* | | | Fix up CREDIT entry orderingLi Yang2007-06-201-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Reorder my CREDIT entry to make it in alphabetic order by last name. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86_64: fix link warning between for .text and .init.textYinghai Lu2007-06-202-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WARNING: arch/x86_64/kernel/built-in.o(.text+0xace9): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr') WARNING: arch/x86_64/kernel/built-in.o(.text+0xad09): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr') WARNING: arch/x86_64/kernel/built-in.o(.text+0xad38): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr') WARNING: drivers/built-in.o(.text+0x3a680): Section mismatch: reference to .init.text:acpi_map_pxm_to_node (between 'acpi_get_node' and 'acpi_lock_ac_dir') AK: also marked mtrr_bp_init __init to avoid some more warnings Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Andi Kleen <ak@suse.de> Acked-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86: change_page_attr bandaidsAndi Kleen2007-06-202-15/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Disable CLFLUSH again; it is still broken. Always do WBINVD. - Always flush in the i386 case, not only when there are deferred pages. These are both brute-force inefficient fixes, to be improved next release cycle. The changes to i386 are a little more extensive than strictly needed (some dead code added), but it is more similar to the x86-64 version now and the dead code will be used soon. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86: Disable KPROBES with DEBUG_RODATA for nowAndi Kleen2007-06-202-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now Kprobes cannot write to the write protected kernel text when DEBUG_RODATA is enabled. Disallow this in Kconfig for now. Temporary fix for 2.6.22. In .23 add code to temporarily unprotect it. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86: Only make Macintosh drivers default on MacsAndi Kleen2007-06-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's already annoying that they appear on x86 now -- that's for the 3button emulation needed on x86 macs -- but at least don't make them default. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86_64: Quieten Atari keyboard warnings in KconfigAndi Kleen2007-06-202-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Not directly related to x86, but I got tired of seeing these warnings on every kconfig update when building on a non m68k box: drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE' drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE' I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig so it's always seen by Kconfig. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86: Disable DAC on VIA bridgesAndi Kleen2007-06-203-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several reports that VIA bridges don't support DAC and corrupt data. I don't know if it's fixed, but let's just blacklist them all for now. It can be overwritten with iommu=usedac Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86_64: Fix eventd/timerfd syscallsAndi Kleen2007-06-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | They had the same syscall number. Pointed out by Davide Libenzi Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | x86_64: Fix readahead/sync_file_range/fadvise64 compat callsAndi Kleen2007-06-202-3/+22
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Correctly convert the u64 arguments from 32bit to 64bit. Pointed out by Heiko Carstens. I guess this proves Linus' theory that nobody uses the more exotic Linux specific syscalls. It wasn't discovered by a user. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | [POWERPC] rheap - eliminates internal fragments caused by alignmentLi Yang2007-06-191-19/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds fragments caused by rh_alloc_align() back to free list, instead of allocating the whole chunk of memory. This will greatly improve memory utilization managed by rheap. It solves MURAM not enough problem with 3 UCCs enabled on MPC8323. Signed-off-by: Li Yang <leoli@freescale.com> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6Linus Torvalds2007-06-191-0/+1
|\ \ \ | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6: sh64: Handle -ERESTART_RESTARTBLOCK for restartable syscalls.
| * | | sh64: Handle -ERESTART_RESTARTBLOCK for restartable syscalls.Paul Mundt2007-06-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current implementation only handles -ERESTARTNOHAND, whereas we also need to handle -ERESTART_RESTARTBLOCK in the handle_signal() case for restartable system calls. Follows the sh change. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* | | | Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds2007-06-192-3/+9
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: sh: Handle -ERESTART_RESTARTBLOCK for restartable syscalls. sh: oops_enter()/oops_exit() in die(). sh: Fix restartable syscall arg5 clobbering.
| * | | | sh: Handle -ERESTART_RESTARTBLOCK for restartable syscalls.Paul Mundt2007-06-191-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current implementation only handles -ERESTARTNOHAND, whereas we also need to handle -ERESTART_RESTARTBLOCK in the handle_signal() case for restartable system calls. As noted by Carl: This fixes the LTP test nanosleep03 - the current kernel causes -ERESTART_RESTARTBLOCK to reach user space rather than the correct -EINTR. Reported-by: Carl Shaw <shaw.carl@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
OpenPOWER on IntegriCloud