summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ssb: mark bus as powered up earlierRafał Miłecki2011-04-261-4/+4
| | | | | | | | ssb_chipco_set_clockmode may want to touch CC registers to control power of the bus. However touching registers without powered_up set causes warnings. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix AR9160 xpaBiasLvlFreq endianness handlingAdrian Chadd2011-04-261-0/+4
| | | | | | | | | The xpaBiasLvlFreq parameter array is made up of 16 bit words which aren't byte-swapped like the other 16-bit eeprom parameters are. It's only used by the AR9160. Signed-off-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: set beacon related ps flags on bss_info changeRajkumar Manoharan2011-04-262-6/+6
| | | | | | | | | | Requesting beacon sync up to configure beacon timers properly in hw, has be done after doing beacon config with default values. Setting the flags in beacon config is causing the device to not enter into network sleep on idle state. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix Tx IQ Calibration hang issue in AR9003 chipsRajkumar Manoharan2011-04-263-235/+140
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On AR9003 chips, doing three IQ calibrations will possibly cause chip in stuck state. In noisy environment, chip could receive a packet during the middle of three calibrations and it causes the conflict of HW access and the eventual failure. It also causes IQ calibration outliers which results in poor Tx EVM. The IQ Cal procedure is after resetting the chip, run IQ cal 3 times per each cal cycle and find the two closest readings and average of two. The advantage of running Tx IQ cal more than once is that we can compare calibration results for the same gain setting over multiple iterations. Most of the cases the IQ failures were observed after first pass. For the AR9485 and later chips, Tx IQ Calibration is performed along with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated from the rest of calibration HW to avoid chip hang. After all calibrations are done in HW, we can start SW post-processing. By doing this way, we minimize the SW difference among all chips. The order of calibration (run IQ cal before other calibration) is also needed to avoid chip hang for chips before AR9485. This issue was originally observed with AR9382. During the issue kernel log was filled with following message ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000 ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000 ath: Unable to reset channel (2412 MHz), reset status -5 ath: Unable to set channel Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵John W. Linville2011-04-2623-72/+86
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| * iwl4965: fix skb usage after freeStanislaw Gruszka2011-04-201-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit a120e912eb51e347f36c71b60a1d13af74d30e83 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Feb 19 15:47:33 2010 -0800 iwlwifi: sanity check before counting number of tfds can be free we use skb->data after calling ieee80211_tx_status_irqsafe(), which could free skb instantly. On current kernels I do not observe practical problems related with bug, but on 2.6.35.y it cause random system hangs when stressing wireless link, making bisection of other problems impossible. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: fix skb usage after freeStanislaw Gruszka2011-04-201-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit a120e912eb51e347f36c71b60a1d13af74d30e83 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Feb 19 15:47:33 2010 -0800 iwlwifi: sanity check before counting number of tfds can be free we use skb->data after calling ieee80211_tx_status_irqsafe(), which could free skb instantly. On current kernels I do not observe practical problems related with bug, but on 2.6.35.y it cause random system hangs when stressing wireless link. Cc: stable@kernel.org # 2.6.32+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: fix SMPS debugfs lockingJohannes Berg2011-04-202-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The locking with SMPS requests means that the debugs file should lock the mgd mutex, not the iflist mutex. Calls to __ieee80211_request_smps() need to hold that mutex, so add an assertion. This has always been wrong, but for some reason never been noticed, probably because the locking error only happens while unassociated. Cc: stable@kernel.org [2.6.34+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * Merge branch 'master' of ↵John W. Linville2011-04-204-5/+12
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
| | * Bluetooth: Only keeping SAR bits when retransmitting one frame.Ruiyi Zhang2011-04-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | When retrasmitting one frame, only SAR bits in control field should be kept. Signed-off-by: Ruiyi Zhang <Ruiyi.zhang@atheros.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| | * Bluetooth: fix shutdown on SCO socketsLuiz Augusto von Dentz2011-04-181-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | shutdown should wait for SCO link to be properly disconnected before detroying the socket, otherwise an application using the socket may assume link is properly disconnected before it really happens which can be a problem when e.g synchronizing profile switch. Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| | * Bluetooth: Fix keeping the command timer runningVinicius Costa Gomes2011-04-181-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the teardown path the reset command is sent to the controller, this event causes the command timer to be reactivated. So the timer is removed in two situations, when the adapter isn't marked as UP and when we know that some command has been sent. Reported-by: Keith Packard <keithp@keithp.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| | * Bluetooth: Fix refcount balance for hci connectionVille Tervo2011-04-181-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | hci_io_capa_reply_evt() holds reference for hciconnection. It's useless since hci_io_capa_request_evt()/hci_simple_pair_complete_evt() already protects the connection. In addition it leaves connection open after failed SSP pairing. Signed-off-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
| * | ath9k: fix the return value of ath_stoprecvFelix Fietkau2011-04-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect a condition where rx DMA was stopped, but the MAC failed to enter the idle state. This condition requires a hardware reset, however the return value of ath_stoprecv was 'true' in that case, which allowed it to skip the reset when issuing a fast channel change. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Paul Stewart <pstew@google.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | iwlwifi: fix frame injection for HT channelsDaniel Halperin2011-04-181-6/+1
| |/ | | | | | | | | | | | | | | | | | | For some reason, sending QoS configuration causes transmission to stop after a single frame on HT channels when not associated. Removing the extra QoS configuration has no effect on station mode, and fixes injection mode. Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
| * iwlegacy: fix tx_power initializationStanislaw Gruszka2011-04-136-28/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | priv->tx_power_next is not initialized to max supported power, but instead default value is used, what cause errors like [ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14. [ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22). if maximum tx power read from the eeprom is smaller than default. In consequence card is unable to initialize properly. Fix the problem and cleanup tx power initialization. Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k_htc: Fix ethtool reportingSujith Manoharan2011-04-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Pass the correct module name and device interface so that ethtool can display the proper values. The firmware version will be fixed later on when the FW can actually report a version. :) Reported-by: Richard Farina <sidhayn@gmail.com> Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Tested-by: Richard Farina <sidhayn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k_hw: fix stopping rx DMA during resetsFelix Fietkau2011-04-124-16/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During PHY errors, the MAC can sometimes fail to enter an idle state on older hardware (before AR9380) after an rx stop has been requested. This typically shows up in the kernel log with messages like these: ath: Could not stop RX, we could be confusing the DMA engine when we start RX up ------------[ cut here ]------------ WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]() Call Trace: [<8023f0e8>] dump_stack+0x8/0x34 [<80075050>] warn_slowpath_common+0x78/0xa4 [<80075094>] warn_slowpath_null+0x18/0x24 [<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k] [<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k] [<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k] When this happens, the state that the MAC enters is easy to identify and does not result in bogus DMA traffic, however to ensure a working state after a channel change, the hardware should still be reset. This patch adds detection for this specific MAC state, after which the above warnings completely disappear in my tests. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlegacy: make iwl3945 and iwl4965 select IWLWIFI_LEGACYJohn W. Linville2011-04-111-4/+5
| | | | | | | | | | | | | | | | | | | | Otherwise, IWLWIFI_LEGACY has to be selected independently before the drivers are made available. Reported-by: Dave Airlie <airlied@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
| * p54: Initialize extra_len in p54_tx_80211Jason Conti2011-04-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a very serious off-by-one bug in the driver, which could leave the device in an unresponsive state. The problem was that the extra_len variable [used to reserve extra scratch buffer space for the firmware] was left uninitialized. Because p54_assign_address later needs the value to reserve additional space, the resulting frame could be to big for the small device's memory window and everything would immediately come to a grinding halt. Reference: https://bugs.launchpad.net/bugs/722185 Cc: <stable@kernel.org> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Jason Conti <jason.conti@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: fix missing ath9k_ps_wakeup/ath9k_ps_restore callsFelix Fietkau2011-04-081-2/+10
| | | | | | | | | | | | | | | | | | | | These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS boards, but have also been reported to cause radio stability issues on AR9285. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ssb: cc: clear GPIOPULL registers on initRafał Miłecki2011-04-252-0/+8
| | | | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Add TSFOOR interrupt stats in debug infoMohammed Shafi Shajakhan2011-04-252-0/+9
| | | | | | | | | | | | | | | | | | This helped the developers to fix an issue of chip not entering network sleep during idle state, previously this was only available as a debug message Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: remove the unlikely check for autosleepMohammed Shafi Shajakhan2011-04-251-1/+1
| | | | | | | | | | | | | | | | newer chipsets support auto sleep feature, so remove the unlikely check which does not seems to help anything Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Add power save wrappers and modularize hw_pll handlerSenthil Balasubramanian2011-04-253-12/+26
| | | | | | | | | | | | | | | | | | | | We should protect hw_pll handler with power save wrappers and also modularize hw_pll handler properly for better readability. Also add a debug message to track chip resets on pll hang condition. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: cleanup hw pll work handlerSenthil Balasubramanian2011-04-254-23/+25
| | | | | | | | | | | | | | | | | | There is no reason why pll work handler should be part of xmit file. move it to main.c so that reading hw check routines are all in the same place. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: optimize the usage of power save wrappers.Senthil Balasubramanian2011-04-251-4/+2
| | | | | | | | | | | | | | | | | | | | We need not wake up the chip even before mutex lock is acquired and also that it is required only if we are going to drain the txq. So place the wrappers accordingly and this change is also useful when there are no pending frames in the txq as we do not wake up the chip unnecessarily. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: Fix incorrect baseband PLL phase shift for AR9485Senthil Balasubramanian2011-04-251-4/+0
| | | | | | | | | | | | | | | | | | we should program the AR9485 baseband PLL phase shift to 6 and a redundant setting overwrites the correct value. Remove the incorrect and unwnated register setting. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Fix LED gpio for AR93xx chipsets.Senthil Balasubramanian2011-04-252-0/+3
| | | | | | | | | | | | | | | | | | The LED gpio is incorrectly programmed for AR9300 and so the led is not working propelry. AR93xx uses gpio 10 for LED and not the default. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | cfg80211: module_param to disable HT40 in 2.4GHz bandAmitkumar Karwar2011-04-252-18/+17
| | | | | | | | | | | | | | | | | | | | | | | | Currently mac80211 uses ieee80211_disable_40mhz_24ghz module parameter to allow disabling 40MHz operation in the 2.4GHz band. Move this handling from mac80211 to cfg80211 so that the feature will be more generic. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Fix warning: symbol 'ath9k_platform_id_table' was not declared. ↵Vasanthakumar Thiagarajan2011-04-251-1/+1
| | | | | | | | | | | | | | Should it be static? Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Fix bug in configuring hw timerVasanthakumar Thiagarajan2011-04-252-12/+7
| | | | | | | | | | | | | | | | | | Hw next tigger time is configured as current_tsf + (timer_period * 10) which is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration would cause btcoex related issues. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mac80211: tear down BA sessions properly on suspendJohannes Berg2011-04-251-5/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the code to tear down BA sessions will execute after queues are stopped, but attempt to send frames, so those frames will just get queued, which isn't intended. Move this code to before to tear down the sessions properly. Additionally, after stopping queues, flush the TX queues in the driver driver to make sure all the frames went out. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwl8k: Enable life time expiry for tx packets in the hardwareNishant Sarmukadam2011-04-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | Tell the firmware to enable the life time expiry of tx packets in the hardware. The hardware will now refer to the timestamp in every tx packet and decide whether the packet needs to be dropped or transmitted. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwl8k: Reserve buffers for tx management framesNishant Sarmukadam2011-04-251-8/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | Since queues are not stopped anymore, management frames would be dropped if the corresponding tx queue is full. This can cause issues say when we want to setup an ampdu stream and action frames i.e addba requests keep getting dropped frequently. Fix this by reserving some buffers to allow management frames to go through in queue full conditions. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwl8k: Add timestamp information for tx packetsPradeep Nemavat2011-04-251-0/+13
| | | | | | | | | | | | | | | | | | | | | | Timestamp tx packets using a HW micro-second timer. This timestamp will be compared to the current timestamp in the hardware and if the difference is greater than 500ms, the packet will be dropped. Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwl8k: Do not stop tx queuesPradeep Nemavat2011-04-251-13/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is in preparation to support life time expiry of packets in the hardware to avoid head-of-line blocking where a slow client can hog a tx queue and affect the traffic to a faster client from the same queue. Time stamp the packets in driver to allow dropping them in the hardware if they are queued for more than 500ms. If queues are stopped, packets will be queued up outside the driver. Since we will be able to timestamp the packets only after they hit the driver, the timestamp will be less accurate since we cannot consider the time the packets spent in queues outside the driver. With this commit, to achieve accurate timestamping, the tx queues will not be stopped in normal conditions. The only scenarios where the queues will be stopped are when firmware commands are executing or if the interface is brought down. Now, we need to be prepared for a situation where packets hit the driver even after the tx queues are full. Drop all such packets in the driver itself. Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | iwlwifi: fix possible data overwrite in hcmd callbackStanislaw Gruszka2011-04-251-11/+4
| | | | | | | | | | | | | | | | | | | | | | | | My commit 3598e1774c94e55c71b585340e7dc4538f310e3f "iwlwifi: fix enqueue hcmd race conditions" move hcmd callback after command queue reclaim, to avoid call it with hcmd_lock. But since queue read index was updated, cmd data can be overwritten. Fix problem by calling callback before taking hcmd_lock and queue reclaim. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ssb: cc: add & fix definesRafał Miłecki2011-04-251-2/+7
| | | | | | | | | | | | | | We probably got false positive results for checking PLL being down. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Remove unused macros and structuresSujith Manoharan2011-04-252-14/+0
| | | | | | | | | | Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Use power save wrappers when accessing HWSujith Manoharan2011-04-252-3/+23
| | | | | | | | | | Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Fix max A-MPDU size handlingSujith Manoharan2011-04-251-1/+10
| | | | | | | | | | | | | | | | Set the maximum ampdu size of a station correctly in the target by using the ampdu_factor. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_htc: Fix AMPDU subframe handlingSujith Manoharan2011-04-255-20/+35
| | | | | | | | | | | | | | | | | | | | | | * Register the driver's maximum ampdu subframe limit to mac80211. * Cleanup the target capabilities structure and fix an endian issue. * Fix BTCOEX by sending a command to the target when the BT priority changes. * Bump the required firmware version to 1.1 Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Fix warnings from -Wunused-but-set-variableSujith Manoharan2011-04-2511-34/+25
| | | | | | | | | | Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ssb: cc: use correct min_msk for 0x4312Rafał Miłecki2011-04-251-0/+2
| | | | | | | | | | | | | | | | Default min_msk on my 0x4312 is 0x80000CBB, not 0xCBB. Now we follow specs and wl (noticed in MMIO dumps). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ssb: pci: trivial: correct amount of maximum retriesRafał Miłecki2011-04-251-1/+1
| | | | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: Enable AR9340 supportVasanthakumar Thiagarajan2011-04-251-0/+2
| | | | | | | | | | | | | | | | AR9340 is a AR9003 family built-in 2x2 wmac of ar934x SOCs. It is single band in ar9341 SOC and dual band in ar9344/ar9342 SOCs. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: Disable INTR_HOST1_FATAL to avoid interrupt strom with ar9430Vasanthakumar Thiagarajan2011-04-252-5/+11
| | | | | | | | | | Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: Assign macversion based on devid for built-in wmacVasanthakumar Thiagarajan2011-04-251-3/+11
| | | | | | | | | | Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Add AR9340 platform id to id tableVasanthakumar Thiagarajan2011-04-251-0/+4
| | | | | | | | | | Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
OpenPOWER on IntegriCloud