summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* mdio: Add register definitions for MDIO (clause 45)Ben Hutchings2009-04-291-0/+237
| | | | | | | | | | | | | IEEE 802.3 clause 45 specifies the MDIO interface and registers for use in 10G and other PHYs, similar to the MII management interface. PHYs may have up to 32 MMDs corresponding to different sub-layers and functions, each with up to 65536 registers. These are addressed by PRTAD (similar to the MII PHY address) and DEVAD. Define a mapping for specifying PRTAD and DEVAD through the existing MII ioctls. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool: Add port type PORT_OTHERBen Hutchings2009-04-291-0/+1
| | | | | | | | | Add a PORT_OTHER to represent all other physical port types. Current NICs generally do not allow switching between multiple port types in software so specific types should not be needed. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* pcnet32: Remove pointless memory barriersJohn Dykstra2009-04-291-2/+2
| | | | | | | | | | | These two memory barriers in performance-critical paths are not needed on x86. Even if some other architecture does buffer PCI I/O space writes, the existing memory-mapped I/O barriers are unlikely to be what is needed. Signed-off-by: John Dykstra <john.dykstra1@gmail.com> Acked-by: Don Fry <pcnet32@verizon.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Use pci_wake_from_d3() instead of multiple pci_enable_wake()Don Skidmore2009-04-291-11/+6
| | | | | | | | | | We were calling pci_enable_wake() twice in a row for both D3_hot and D3_cold. This replaces those calls with a call to pci_wake_from_d3() to avoid issues with PCI PM vs ordering constraints. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: fix firmware downloadDhananjay Phadke2009-04-284-207/+216
| | | | | | | | | | o hold the firmware in memory across suspend, since filesystem may not be up after resuming. o reset the chip after requesting firmware, to minimize downtime for NC-SI. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: refactor netxen_recv_context structDhananjay Phadke2009-04-285-40/+71
| | | | | | | | o move related fields into netxen_recv_context struct. o allocate rx buffer and descriptor rings dynamically. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: fix link event handlingDhananjay Phadke2009-04-283-2/+3
| | | | | | | | Firmware starting 4.0.402 started supporting link events, disable it for older firmwares. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gianfar: Use memset instead of cacheable_memzeroKumar Gala2009-04-281-1/+2
| | | | | | | | | | cacheable_memzero() is completely overkill for the clearing out the FCB block which is only 8-bytes. The compiler should easily optimize this with memset. Additionally, cacheable_memzero() only exists on ppc32 and thus breaks builds of gianfar on ppc64. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* inet_diag: Remove dup assignmentsArnaldo Carvalho de Melo2009-04-281-2/+0
| | | | | | | These are later assigned to other values without being used meanwhile. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: netif_tx_queue_stopped too expensiveEric Dumazet2009-04-281-2/+8
| | | | | | | | | | | | | | | | | | | | | | netif_tx_queue_stopped(txq) is most of the time false. Yet its cost is very expensive on SMP. static inline int netif_tx_queue_stopped(const struct netdev_queue *dev_queue) { return test_bit(__QUEUE_STATE_XOFF, &dev_queue->state); } I saw this on oprofile hunting and bnx2 driver bnx2_tx_int(). We probably should split "struct netdev_queue" in two parts, one being read mostly. __netif_tx_lock() touches _xmit_lock & xmit_lock_owner, these deserve a separate cache line. Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Fix ucc_geth.c handling of fixed-link w/o phy-connection-type property.Grant Likely2009-04-281-3/+0
| | | | | | | | | | | Previous rework to ucc_geth.c to add of_mdio support (net: Rework ucc_geth driver to use of_mdio infrastructure) added a block of code which broke older openfirmware device trees which this case. This patch removes the offending blurb. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
* fs_enet: Remove dead codeKumar Gala2009-04-283-77/+1
| | | | | | | | | | CONFIG_DUET doesn't exist anymore, remove all the code that exists to support it. [ Simplify fs_init() even further -DaveM ] Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Clear out stray tx work on link downNelson, Shannon2009-04-281-0/+22
| | | | | | | | | | Ayyappan at VMware noticed that we're missing this check from ixgbe which is in our other drivers. The difference with this implementation from our other drivers is that this checks all the tx queues rather than just tx[0]. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Interrupt management update for 82599Nelson, Shannon2009-04-281-40/+50
| | | | | | | | | Update the interrupt management to correctly handle greater than 16 queue vectors. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: enable HW RSC for 82599Alexander Duyck2009-04-284-12/+152
| | | | | | | | | | | | | | | | | This patch enables hardware receive side coalescing for 82599 hardware. 82599 can merge multiple frames from the same TCP/IP flow into a single structure that can span one ore more descriptors. The accumulated data is arranged similar to how jumbo frames are arranged with the exception that other packets can be interlaced inbetween. To overcome this issue a next pointer is included in the written back descriptor which indicates the next descriptor in the writeback sequence. This feature sets the NETIF_F_LRO flag and clearing it via the ethtool set flags operation will also disable hardware RSC. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: enable hardware offload for sctpJesse Brandeburg2009-04-282-2/+18
| | | | | | | | | | | | | Inspired by: Vlad Yasevich <vladislav.yasevich@hp.com> This is the code to enable ixgbe for hardware offload support of CRC32c on both transmit and receive of SCTP traffic. only 82599 supports this offload, not 82598. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: Enable SCTP checksum offloadingJesse Brandeburg2009-04-284-4/+31
| | | | | | | | | | | | | | | | | | | | | | Originally from: Vlad Yasevich <vladislav.yasevich@hp.com> This patch, both the driver portion and the sctp code was modified by Jesse Brandeburg and is Copyright(c) 2009 Intel Corporation. Thanks go to Vlad for starting this work. Intel 82576 chipset supports SCTP checksum offloading. This patch enables this functionality in the driver. A new NETIF feature is introduced for SCTP checksum offload. If the driver supports CRC32c checksum, it can set this feature flag. The hardware can offload both transmit and receive. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sctp: add feature bit for SCTP offload in hardwareJesse Brandeburg2009-04-282-3/+16
| | | | | | | | | | | | | | this is the sctp code to enable hardware crc32c offload for adapters that support it. Originally by: Vlad Yasevich <vladislav.yasevich@hp.com> modified by Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb/ixgbe: remove unecessary checks for CHECKSUM_UNNECESSARYAlexander Duyck2009-04-282-26/+11
| | | | | | | | | | | | Both of these drivers do a check to verify ip_summed is set to CHECKSUM_UNNECESSARY prior to passing the packet to GRO. GRO itself already does such a check so it is redundant and can be removed as this will likely cause out of order issues when receiving a packet that didn't pass checksum validation. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: make rxcsum configuration seperate from multiqueueAlexander Duyck2009-04-282-20/+12
| | | | | | | | | | The igb driver was being incorrectly setup to only allow disabling receive checksum if multiqueue was disabled. This change corrects that so that RXCSUM is configured regardless of queue configuration. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: reconfigure mailbox timeout logicAlexander Duyck2009-04-281-4/+4
| | | | | | | | | | This change updates the timeout logic so that it is not possible to have a sucessful check for message and still return an error if countdown = 0. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: Juha Leppanen <juha_motorsportscom@luukku.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: add fifo byteswap support V2Magnus Damm2009-04-282-0/+23
| | | | | | | | | | | | | | | | This is V2 of the smsc911x fifo byteswap patch. The smsc911x hardware supports both big and little and endian hardware configurations, and the linux smsc911x driver currently detects word order. For correct operation on big endian platforms lacking swapped byte lanes the following patch is needed. Only fifo data is swapped, register data does not require any swapping. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* atl1c: disable L1/L0s when link detectedJie Yang2009-04-281-17/+7
| | | | | | | | | Disable L1/L0s when link detected. We enable L1/L0s when link connected before, but there is some hareware error on some platform. So just diable this feature when link connected. This feature is about power saving. Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gro: Fix COMPLETE checksum handlingHerbert Xu2009-04-273-2/+9
| | | | | | | | | On a brand new GRO skb, we cannot call ip_hdr since the header may lie in the non-linear area. This patch adds the helper skb_gro_network_header to handle this. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* gro: Fix handling of headers that extend over the tailHerbert Xu2009-04-272-9/+4
| | | | | | | | | | | The skb_gro_* code fails to handle the case where a header starts in the linear area but ends in the frags area. Since the goal of skb_gro_* is to optimise the case of completely non-linear packets, we can simply bail out if we have anything in the linear area. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: driver version 1.48.105-1Vladislav Zolotarov2009-04-271-2/+2
| | | | | | Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Removed blob fileVladislav Zolotarov2009-04-271-16322/+0
| | | | | | Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Separated FW from the source.Vladislav Zolotarov2009-04-278-598/+866
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | >From now on FW will be downloaded from the binary file using request_firmware. There will be different files for every supported chip. Currently 57710 (e1) and 57711 (e1h). File names have the following format: bnx2x-<chip version>-<FW version>.fw. ihex versions of current FW files are submitted in the next patch. Each binary file has a header in the following format: struct bnx2x_fw_file_section { __be32 len; __be32 offset; } struct bnx2x_fw_file_hdr { struct bnx2x_fw_file_section init_ops; struct bnx2x_fw_file_section init_ops_offsets; struct bnx2x_fw_file_section init_data; struct bnx2x_fw_file_section tsem_int_table_data; struct bnx2x_fw_file_section tsem_pram_data; struct bnx2x_fw_file_section usem_int_table_data; struct bnx2x_fw_file_section usem_pram_data; struct bnx2x_fw_file_section csem_int_table_data; struct bnx2x_fw_file_section csem_pram_data; struct bnx2x_fw_file_section xsem_int_table_data; struct bnx2x_fw_file_section xsem_pram_data; struct bnx2x_fw_file_section fw_version; } Each bnx2x_fw_file_section contains the length and the offset of the appropriate section in the binary file. Values are stored in the big endian format. Data types of arrays: init_data __be32 init_ops_offsets __be16 XXsem_pram_data u8 XXsem_int_table_data u8 init_ops struct raw_op { u8 op; __be24 offset; __be32 data; } fw_version u8 >From now boundaries of a specific initialization stage are stored in init_ops_offsets array instead of being defined by separate macroes. The index in init_ops_offsets is calculated by BLOCK_OPS_IDX macro: #define BLOCK_OPS_IDX(block, stage, end) \ (2*(((block)*STAGE_IDX_MAX) + (stage)) + (end)) Security: In addition to sanity check of array boundaries bnx2x will check a FW version. Additional checks might be added in the future. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: FW 4.8.53.0Vladislav Zolotarov2009-04-272-0/+22392
| | | | | | Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tun: add IFF_TUN_EXCL flag to avoid opening a persistent device.David Woodhouse2009-04-272-0/+3
| | | | | | | | | | | | | | | | | | | | | When creating a certain types of VPN, NetworkManager will first attempt to find an available tun device by iterating through 'vpn%d' until it finds one that isn't already busy. Then it'll set that to be persistent and owned by the otherwise unprivileged user that the VPN dæmon itself runs as. There's a race condition here -- during the period where the vpn%d device is created and we're waiting for the VPN dæmon to actually connect and use it, if we try to create _another_ device we could end up re-using the same one -- because trying to open it again doesn't get -EBUSY as it would while it's _actually_ busy. So solve this, we add an IFF_TUN_EXCL flag which causes tun_set_iff() to fail if it would be opening an existing persistent tundevice -- so that we can make sure we're getting an entirely _new_ device. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* cxacru: Fix negative dB outputSimon Arlott2009-04-271-2/+8
| | | | | | | | | Values of dB between -0.99 and -0.01 will be output with the wrong sign. This converts the negative value to positive and outputs it with a "-" prefix. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: David S. Miller <davem@davemloft.net>
* pasemi_mac: mac_to_intf() error not noticedroel kluin2009-04-271-3/+4
| | | | | | | | | mac_to_intf() can return -1 when no device or function is found, but when mac->dma_if is unsigned. The error wasn't noticed. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drop_monitor: Update netlink protocol to include netlink attribute header in ↵Neil Horman2009-04-271-3/+10
| | | | | | | | | | | | | | | | | alert message When I initially implemented this protocol, I disregarded the use of netlink attribute headers, thinking for my purposes they weren't needed. I've come to find out that, as I'm starting to work with sending down messages with associated data (like config messages), the kernel code spits out warnings about trailing data in a netlink skb that doesn't have an associated header on it. As such, I'm going to start including attribute headers in my netlink transaction, and so for completeness, I should likely include them on messages bound from the kernel to user space. This patch adds that header to the kernel, and bumps the protocol version accordingly Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: Disallow SFP 1G modules in the SFP+ cages for 82598 and 82599Waskiewicz Jr, Peter P2009-04-272-5/+18
| | | | | | | | | | | | 82598 and 82599 do not support SFP 1G modules. Instead of allowing the driver to load, but never get link, rejecting the module and displaying a useful message is more preferrable. The framework for displaying the failure message already exists, now we just need to detect and reject the SFP modules. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: always use adapter->itr as EITR valueAlexander Duyck2009-04-271-5/+6
| | | | | | | | | | | | The igb driver was switching between adapter->itr containing the EITR value and the number of interrupts per second. This resulted in high latencies being seen after brining the interface down and then back up. To resolve the issue the itr value will now only contain the value that should be programmed into EITR. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxge: use max() instead of VXGE_HW_SET_LEVELAlexander Beregalov2009-04-272-34/+23
| | | | | | Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Acked-by: Ram Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxge: fix possible NULL dereference in vxge-traffic.cAlexander Beregalov2009-04-271-2/+2
| | | | | | | | If vpath is NULL then hldev is NULL also. Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Acked-by: Ram Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: ignore updelay param when there is no active slaveJiri Pirko2009-04-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | Pointed out by Sean E. Millichamp. Quote from Documentation/networking/bonding.txt: "Note that when a bonding interface has no active links, the driver will immediately reuse the first link that goes up, even if the updelay parameter has been specified (the updelay is ignored in this case). If there are slave interfaces waiting for the updelay timeout to expire, the interface that first went into that state will be immediately reused. This reduces down time of the network if the value of updelay has been overestimated, and since this occurs only in cases with no connectivity, there is no additional penalty for ignoring the updelay." This patch actually changes the behaviour in this way. Signed-off-by: Jiri Pirko <jpirko@redhat.com> drivers/net/bonding/bond_main.c | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: use ethtool for link checking firstJiri Pirko2009-04-271-14/+12
| | | | | | | | | | | | | | This patch only changes the order of interfaces to use for checking slave link status in bond_check_dev_link() to priorize ethtool interface. Should safe some troubles as ethtool seems to be more supported. Jirka Signed-off-by: Jiri Pirko <jpirko@redhat.com> drivers/net/bonding/bond_main.c | 26 ++++++++++++-------------- 1 files changed, 12 insertions(+), 14 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fix fsl_pq_mdio driver to use module_init()Grant Likely2009-04-271-1/+1
| | | | | | | | | | | | | | | | | Modules are not supposed to use any of the *_initcall*() hooks as the entry point. fsl_pq_mdio.c was using subsys_initcall_sync() instead of module_init() to guarantee that the MDIO bus was initialized before the Ethernet driver goes looking for the phy. However, the recent OF helpers rework happens to also make sure PHY connection is deferred to .open time, so using an initcall is no longer necessary. This patch replaces the initcall with a more traditional an accepted module_init() call. Tested on Freescale MPC8349emitxgp eval board. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: add Xilinx ll_temac device driverGrant Likely2009-04-275-0/+1473
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Rework fs_enet driver to use of_mdio infrastructureGrant Likely2009-04-274-114/+16
| | | | | | | | This patch simplifies the driver by making use of more common code. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* powerpc/82xx: Rework Embedded Planet ep8248e platform to use of_mdioGrant Likely2009-04-271-6/+3
| | | | | | | | | This patch modifies the bitbanged MDIO driver in the ep8248e platform code to use the common of_mdio infrastructure. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Rework ucc_geth driver to use of_mdio infrastructureGrant Likely2009-04-272-36/+13
| | | | | | | | This patch simplifies the driver by making use of more common code. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Rework pasemi_mac driver to use of_mdio infrastructureGrant Likely2009-04-273-52/+9
| | | | | | | | | | This patch simplifies the driver by making use of more common code. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Tested-by: Olof Johansson <olof@lixom.net> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Rework gianfar driver to use of_mdio infrastructure.Grant Likely2009-04-272-74/+39
| | | | | | | | | | This patch simplifies the driver by making use of more common code. Tested on Freescale MPC8349emitxgp eval board Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: rework fsl_pq_mdio driver to use of_mdio infrastructureGrant Likely2009-04-271-48/+3
| | | | | | | | | | This patch simplifies the driver by making use of more common code. Tested on Freescale MPC8349emitxgp eval board Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Rework mpc5200 fec driver to use of_mdio infrastructure.Grant Likely2009-04-272-147/+59
| | | | | | | | | | | | | | | The patch reworks the MPC5200 Fast Ethernet Controller (FEC) driver to use the of_mdio infrastructure for registering PHY devices from data out openfirmware device tree, and eliminates the assumption that the PHY for the FEC is always attached to the FEC's own MDIO bus. With this patch, the FEC can use a PHY attached to any MDIO bus if it is described in the device tree. Tested on Freescale Lite5200b eval board Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* openfirmware: Add OF phylib support codeGrant Likely2009-04-274-0/+168
| | | | | | | | | | | | | | Add support for parsing the device tree for PHY devices on an MDIO bus. Currently many of the PowerPC ethernet drivers are open coding a solution for reading data out of the device tree to find the correct PHY device. This patch implements a set of common routines to: a) let MDIO bus drivers register phy_devices described in the tree, and b) let MAC drivers find the correct phy_device via the tree. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phylib: add *_direct() variants of phy_connect and phy_attach functionsGrant Likely2009-04-272-33/+90
| | | | | | | | | | | | | | Add phy_connect_direct() and phy_attach_direct() functions so that drivers can use a pointer to the phy_device instead of trying to determine the phy's bus_id string. This patch is useful for OF device tree descriptions of phy devices where the driver doesn't need or know what the bus_id value in order to get a phy_device pointer. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud