summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* [media] omap3isp: ccdc: Remove ispccdc_syncif structureLaurent Pinchart2012-08-113-40/+20
| | | | | | | | | | The structure is only used to store configuration data and pass it to CCDC configuration functions. Access the data directly from the locations that need it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: ccdc: Remove support for interlaced data and master HS/VS modeLaurent Pinchart2012-08-112-67/+2
| | | | | | | | Those features are half-implemented and not used. Remove them. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: csi2: Add V4L2_MBUS_FMT_YUYV8_2X8 supportIvaylo Petrov2012-08-111-2/+25
| | | | | | | | | | | | | | | | | | Tested with ov9740 and struct isp_csi2_platform_data { .interface = ISP_INTERFACE_CSI2A_PHY2, .bus = { .csi2 = { .crc = 1, .vpclk_div = 1, } }, } Signed-off-by: Ivaylo Petrov <ivpetrov@mm-sol.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: video: Add YUYV8_2X8 and UYVY8_2X8 supportLaurent Pinchart2012-08-111-0/+6
| | | | | Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: video: Split format info bpp field into width and bppLaurent Pinchart2012-08-113-29/+32
| | | | | | | | | | | The bpp field currently stores the sample width and is aligned to the next multiple of 8 bits when computing data size in memory. This won't work anymore for YUYV8_2X8 formats. Split the bpp field into a sample width and a bytes per pixel value. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: preview: Add support for non-GRBG Bayer patternsLaurent Pinchart2012-08-114-60/+91
| | | | | | | | | | Rearrange the CFA interpolation coefficients table based on the Bayer pattern. Support for non-Bayer CFA patterns is dropped as they were not correctly supported, and have never been tested. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: preview: Merge gamma correction and gamma bypassLaurent Pinchart2012-08-112-23/+23
| | | | | | | | | Enabling gamma bypass disables gamma correction and vice versa. Merge the two parameters. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: preview: Reorder configuration functionsLaurent Pinchart2012-08-111-226/+226
| | | | | | | | | Reorder the configuration and enable functions to match the parameters order. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: preview: Pass a prev_params pointer to configuration functionsLaurent Pinchart2012-08-111-117/+83
| | | | | | | | | | | | | | Instead of using void pointers and offset arithmetics to compute a pointer to configuration parameters in a generic way, pass the complete parameters structure to configuration functions and let them access the parameters they need. Also modify the enable functions to use a bool enable parameter instead of a u8. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: preview: Remove lens shading compensation supportLaurent Pinchart2012-08-111-17/+1
| | | | | | | | The feature isn't fully implemented and doesn't work, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: queue: Fix omap3isp_video_queue_dqbuf() description commentMichael Jones2012-08-111-6/+7
| | | | | | Signed-off-by: Michael Jones <michael.jones@matrix-vision.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: ccdc: No semicolon is needed after switch statementPeter Meerwald2012-08-111-2/+2
| | | | | | Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: Configure HS/VS interrupt source before enabling interruptsLaurent Pinchart2012-08-111-17/+26
| | | | | | | | | | This needs to be performed before enabling interrupts as the sensor might be free-running and the ISP default setting (HS edge) would put an unnecessary burden on the CPU. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] omap3isp: Don't access ISP_CTRL directly in the statistics modulesLaurent Pinchart2012-08-115-25/+14
| | | | | | | | | Use the existing omap3isp_subclk_enable() and omap3isp_subclk_disable() functions instead. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] vivi: zero fmt.pix.priv as per specHans Verkuil2012-08-111-0/+1
| | | | | Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] vivi: add frame size reportingHans Verkuil2012-08-111-0/+22
| | | | | Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] vivi: fix colorspace setupHans Verkuil2012-08-111-12/+13
| | | | | | | Two of the four possible YUV formats got the wrong colorspace. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: fix possible race condition in usage of dev->ctrlmsgDevin Heitmueller2012-08-111-28/+12
| | | | | | | | | | | | | | | | | | | The register read function is referencing the dev->ctrlmsg structure outside of the dev->mutex lock, which can cause corruption of the value if multiple callers are invoking au0828_readreg() simultaneously. Use a stack variable to hold the result, and copy the buffer returned by usb_control_msg() to that variable. In reality, the whole recv_control_msg() function can probably be collapsed into au0288_readreg() since it is the only caller. Also get rid of cmd_msg_dump() since the only case in which the function is ever called only is ever passed a single byte for the response (and it is already logged). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] em28xx: Remove useless runtime->private_data usageEzequiel García2012-08-101-1/+0
| | | | | Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mantis: Terratec Cinergy C PCI HD (CI)Igor M. Liplianin2012-08-102-2/+2
| | | | | | | | This patch seems for rectifying a typo. But actually the difference between mantis_vp2040.c and mantis_vp2033.c code is a card name only. Signed-off-by: Igor M. Liplianin <liplianin@me.by> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: change filename to production/redistributable xc5000c firmwareDevin Heitmueller2012-08-091-1/+1
| | | | | | | | | | | | | | | | | | | The original xc5000c driver support was based on a beta version of the firmware, and there were no redistribution rights. Change over to using the release version, for which freely redistributable firmware can be found here: http://kernellabs.com/firmware/xc5000/README.xc5000c http://kernellabs.com/firmware/xc5000/dvb-fe-xc5000c-4.1.30.7.fw Thanks to Ramon Cazares from Cresta Technology for making the firmware available as well as working out the licensing issues. [mchehab@redhat.com: Fix a merge conflict with the patch that added support for MODULE_FIRMWARE() macro] Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Cc: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: make xc5000 firmware speedup apply to the xc5000c as wellDevin Heitmueller2012-08-091-1/+2
| | | | | | | | | | Make the firmware speedup work for the 5000c as well as the original xc5000. This cuts firmware load time in half. Thanks to John Casey at Hauppauge for loaning me a board for testing. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: fix a couple of missed edge cases for i2c gate with analogDevin Heitmueller2012-08-091-0/+16
| | | | | | | | | This patch addresses a couple of cases where I forgot to pop open the gate when in analog mode (a correlary to fix the change made in patch 1c58d5b4a5fca42dce5428bd79b9405878017735). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: show debug version fields in decimal instead of hexDevin Heitmueller2012-08-091-1/+1
| | | | | | | | | | | | The driver prints out a dotted version number but it's in hex. As a result, the version doesn't visibly match the filename for the firmware, and it caused a bunch of confusion while discussing different versions with the chip manufacturer. Change the firmware printout to be in decimal. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: tweak workaround for i2c clock stretching bugDevin Heitmueller2012-08-092-2/+3
| | | | | | | | | | | | | | | The hack I put in a couple of years ago to avoid clock stretching issues when talking to the xc5000 worked fine for writes, but intermittently fails for register reads, because the xc5000 may stretch the clock for longer between bytes (I was seeing cases of 21 us on the analyzer). The problem manifested itself as the xc5000 firmware version and PLL lock register intermittently showing garbage values. Slow down the i2c bus from 30 KHz to 20 KHz to accommodate. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: add support for firmware load check and init statusDevin Heitmueller2012-08-091-0/+39
| | | | | | | | | | | The xc5000c and newer versions of the xc5000a firmware need minor revisions to their initialization process. Add support for validating the firmware was properly loaded, as well as checking the init status after initialization. Based on advice from CrestaTech support as well as xc5000 datasheet v2.3. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: reset device if encountering PLL lock failureDevin Heitmueller2012-08-091-6/+52
| | | | | | | | | | | | | | It's possible for the xc5000 to enter an unknown state such that all subsequent tuning requests fail. The only way to recover is to reset the tuner and reload the firmware. This problem was detected after several days straight of issuing tuning requests every five seconds. Reset the firmware in the event that the PLL is in an unlocked state. This solution was provided by the engineer at CrestaTech (the company that acquired Xceive). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: tune retry interval for i2c interactionDevin Heitmueller2012-08-091-2/+2
| | | | | | | | | | | | Adjust the retry timeout and number of retries to speed up xc5000 firmware download. With this change it goes from 4.2 seconds to 2.9. The net time waited is pretty much the same, but we just poll more often. Tested at 250 KHz as well as 30 KHz. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: remove control buffer from send_control_msgDevin Heitmueller2012-08-091-8/+6
| | | | | | | | | | There are no cases where a control message is ever sent to the au0828 with an actual buffer defined. Remove the reference to dev->ctrlmsg, which currently requires us to hold a mutex since it is shared with the read function. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: speed up i2c clock when doing xc5000 firmware loadDevin Heitmueller2012-08-091-3/+13
| | | | | | | | | | | Put a hack in place to speed up the firmware load in the case that the xc5000 has just been reset. The chip can safely do 400 KHz in this mode, while in normal operation it can only do 100 KHz. This reduces the firmware load time from 6.9 seconds to 4.2. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: fix case where STREAMOFF being called on stopped stream ↵Devin Heitmueller2012-08-091-4/+8
| | | | | | | | | | | | | causes BUG() We weren't checking whether the resource was in use before calling res_free(), so applications which called STREAMOFF on a v4l2 device that wasn't already streaming would cause a BUG() to be hit (MythTV). Reported-by: Larry Finger <larry.finger@lwfinger.net> Reported-by: Jay Harbeston <jharbestonus@gmail.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: prevent i2c gate from being kept open while in analog modeDevin Heitmueller2012-08-095-5/+22
| | | | | | | | | | | | | | | | | | | | | | | | The original implementation of the analog support would use an i2c_gate_ctrl function when using the digital side of the au8522, but on the analog side we would always just force the gate open and leave it open all the time. This can have adverse effects on the xc5000 given the tuner is receiving all the spurious i2c traffic (a problem which can be exaggerated due to bugs in the au0828 i2c hardware implementation). Rework the existing hack to only open/close the gate when actually talking to the tuner. This logic might need to be reworked a bit if anybody ever tries to add support for a board that has the au0828/au8522 but doesn't have digital support implemented (because the i2c_gate_ctrl callback is being set in the DVB attach). However given how few different models are in circulation, this can be deferred until such a situation arises (if ever). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: don't invoke auto calibration unless we really did reset tunerDevin Heitmueller2012-08-091-22/+18
| | | | | | | | | | | | | | | The current code invokes the auto calibration of the tuner whenever the init routine is called (whenever the DVB frontend opens the device). However we should really only be invoking the calibration if we actually did reset the device and reload the firmware. Rework the routine to only do calibration if reset and firmware load was performed. Also because the called function is now a no-op if the firmware is already loaded, the caller no longer needs to invoke is_firmware_loaded(). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au8522: fix regression in logging introduced by separation of modulesDevin Heitmueller2012-08-091-2/+7
| | | | | | | | | | | | The au8522 driver was broken into three modules (dig, decoder, common), and as a result the debug modprobe option doesn't work for any of the common functions. Copy the module macros over to the common module so that the debug option works again. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: make sure video standard is setup in tuner-coreDevin Heitmueller2012-08-092-0/+11
| | | | | | | | | | | | | | | | | | | If the user performs a tuning attempt without explicitly calling the s_std ioctl(), a value of zero is sent from tuner-core to xc5000. This causes the xc5000 driver to leave the standard unchanged. The problem was masked by the fact that the xc5000 driver defaulted to NTSC, but if you happened to perform an ATSC/ClearQAM tuning attempt and then do an analog tune, the net effect is an analog tune with the standard still set to DTV6. Keep track of whether the standard has ever been sent to tuner-core. We don't make an s_std subdev call explicitly during probe because that will cause a firmware load (which is very time consuming on the 950q). With the logic in this patch, the s_std call will occur automatically on the s_freq call if it hasn't already been set. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: fix race condition that causes xc5000 to not bind for digitalDevin Heitmueller2012-08-092-13/+13
| | | | | | | | | | | | | | | In some cases users would see the xc5000_attach() call failing for the digital side of the tuner on initialization. This is because of udev running v4l-id while the digital side of the board is still coming up. This is the exact same race condition which was present in em28xx (not surprising since I copied all the locking logic from that driver when I added analog support). Reproduce Mauro's fix from the em28xx driver in au0828. Reported-by: Rick Harding <rharding@mitechie.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: properly report i2c write failuresDevin Heitmueller2012-08-091-1/+1
| | | | | | | | | The logic as written would *never* actually return an error condition, since the loop would run until the counter hit zero but the check was for a value less than zero. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: add support for showing the SNR and gain in the debug outputDevin Heitmueller2012-08-091-0/+20
| | | | | | | | When debugging is enabled, also show the analog SNR and the total gain status values. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] xc5000: properly show quality register valuesDevin Heitmueller2012-08-091-1/+1
| | | | | | | | | The quality register only has relevant data in bits 2-0, so discard the other bits (which results in a value being printed that is consistent with the expected 0-7 range). Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au0828: Make the s_reg and g_reg advanced debug calls work against ↵Devin Heitmueller2012-08-091-3/+8
| | | | | | | | | | | the bridge The g_reg and s_reg calls worked properly if acting on subdev registers (such as the au8522), but didn't work against the au0828 itself. Copy the logic over from em28xx. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au8522: properly recover from the au8522 delivering misaligned TS ↵Devin Heitmueller2012-08-092-6/+49
| | | | | | | | | | | | | | | | | | | | | | streams There is an apparent bug in the au8522 TS clocking which can result in it delivering a TS payload to the au0828 that is shifted by some number of bits. For example, the device will announce a packet containing "FA 38 FF F8" which if you shift left one bit is "1F 47 1F FF F0..." This presents itself as no TS stream being delivered from the kernel to userland, since the kernel demux will drop every packet. In the event that this condition occurs, restart the DVB stream. Also, this patch includes a couple of lines of cleanup to not change the FIFO configuration while the FIFO is running (which can screw up the state machine), and dequeue the buffers before turning off the FIFO. This puts the logic in sync with the Windows driver. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au8522: Fix off-by-one in SNR table for QAM256Devin Heitmueller2012-08-091-48/+48
| | | | | | | | | | | | | | The table of valid SNR values for QAM 256 is off by one, and as a result if the SNR is oscillating between 40.0 and 39.9 dB, tools like azap show it going back and forth between 40.0 and 0 (misleading some people, including myself, to think signal lock is being lost or there is a problem with register reads). Fix the table so that 40.0 dB is properly represented. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] au8522: fix intermittent lockup of analog video decoderDevin Heitmueller2012-08-092-5/+29
| | | | | | | | | | | | | | It turns up the autodetection for the video standard in the au8522 is prone to hanging the chip until a reset is performed. This condition is trivial to reproduce simply by tuning to a station and then rapidly unplugging/ replugging the coax feed. Because we've never claimed to support anything other than NTSC-M, just disable the video-standard autodetection logic and force it to always be NTSC-M. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] v4l2-dev: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-093-60/+15
| | | | | | | | All drivers that needed V4L2_FL_LOCK_ALL_FOPS have been converted, so remove this flag altogether. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] mem2mem_testdev: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-9/+20
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] vpif_capture: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-8/+20
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] vpif_display: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-11/+23
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] s5p-mfc: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-6/+13
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] s5p-tv: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-8/+21
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* [media] s5p-g2d: remove V4L2_FL_LOCK_ALL_FOPSHans Verkuil2012-08-091-6/+21
| | | | | | | | Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OpenPOWER on IntegriCloud