summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* [SCSI] Add missing scsi command definitionsMartin K. Petersen2010-04-301-0/+2
| | | | | | | Add definitions for VERIFY(12) and VERIFY(32). Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] scsi_debug: Block Limits VPD page fixesMartin K. Petersen2010-04-301-0/+16
| | | | | | | | | Add a few clarifying comments in the B0 page function and allow the optimal transfer length field to be specified on the command line using opt_blks=N. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mvsas: fix hot plug handling and IO issuesSrinivas2010-04-115-80/+186
| | | | | | | | | | | | | | | | | | | | | This patch adds a bunch of fixes 1. Reduce sg table size to 64 (SG_MX) instead of default SG_ALL 2. clear task lists on phy down events 3. release all tasks on port deformation 4. release current task for device gone notification 5. Add sata abort handing 6. Add 10ms delay to each port reset (currently done serially and with interrupts disabled) [jejb: whitespace fixes and clean ups plus added description added dummy 94xx_clear_srs_irq function just to prevent the mismatch in the mvs_dispatch structure killing 94xx cards] Signed-off-by: Srinivas <satyasrinivasp@hcl.in> Cc: Andy Yan <ayan@marvell.com> Cc: qswang@marvell.com Cc: jfeng@marvell.com Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] iscsi_tcp: Remove unused field iscsi_conn from struct iscsi_sw_tcp_connAvi Kaplan2010-04-111-1/+0
| | | | | | | | iscsi_conn is not used so remove it from iscsi_sw_tcp_conn. Signed-off-by: Avi Kaplan <savik751@gmail.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] iscsi_tcp: Change iscsi_sw_tcp_conn_restore_callbacks argumentsAvi Kaplan2010-04-111-2/+4
| | | | | | | | | | This patch changes the arguments to iscsi_sw_tcp_conn_restore_callbacks, so that it works like the function to set the callbacks and because in upcoming patches we need a iscsi_conn. Signed-off-by: Avi Kaplan <savik751@gmail.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] scsi_dh_emc: request flag cleanupMike Christie2010-04-111-2/+0
| | | | | | | | | blk_get_request sets the cmd_flags, so we should not and do not need to set them. If we did set them to a different value then it can cause a oops in the elevator code. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] iscsi_tcp: change & to &&Dan Carpenter2010-04-111-1/+1
| | | | | | | | | | | | | | | This change is basically a clean up. datadgst_en is an int which comes from the user. I didn't see anything limiting it to 1 and 0 although obviously that's what it's supposed to be. If the user passed in 2 this test would fail. This same if condition is repeated in another function and it uses && there. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfc, fcoe: normalize format specifies for world wide namesChris Leech2010-04-114-13/+17
| | | | | | | | | | | Print all world wide node names (node, port and fabric) with the same format specifier of "%16.16llx". That makes sure they all print as a 16 character hex string, with lower case letters, no 0x prefix, and without stripping off any leading 0s. Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfc: set both precision and field with when printing FC IDsChris Leech2010-04-114-21/+21
| | | | | | | | | | | | Most of the prints of fabric IDs were specified as %6x, which will not print any leading 0s. It's nice to see leading 0s for identifiers like this, which are a fixed length. This patch sets the precision modifier as well, making the specifier %6.6x, which forces the printing of leading 0s. Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfc: bug in erroring out upon FCP_RSP_LEN_VAL in fc_fcp_respYi Zou2010-04-111-2/+1
| | | | | | | | | | fc_fcp_resp is assuming when FCP_SNS_LEN_VAL is set, the FCP_RSP_LEN_VAL is not, which is not true. This leads to not copying the sense data and error out a valid FCP_RSP. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fcoe, fnic, libfc: increased CDB size to 16 bytes for fcoe.Vasu Dev2010-04-114-2/+6
| | | | | | | | | | | | | | No reason to restrict CDB size to 12 bytes in fcoe, so increased to 16 so that 16 bytes SCSI CDB doesn't fail. Uses common define to set max_cmd_len for fcoe and fnic, fnic is already setting max_cmd_len to 16. sg_readcap -l fails without this fix. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fcoe: removes unused shost in fcoe_shost_configVasu Dev2010-04-111-6/+2
| | | | | | Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fnic: Change fnic_flush_tx() to flush tx instead of rx queueBrian Uchino2010-04-111-1/+1
| | | | | | | | | | | | fnic_flush_tx() is used to send frames held while fabric login is in progress. The frames are held in tx_queue, but fnic_flush_tx() was incorrectly flushing from recv_queue which is used for received frames. Signed-off-by: Brian Uchino <buchino@cisco.com> Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fnic: Update version to 1.4.0.145Brian Uchino2010-04-111-1/+1
| | | | | | | | | New fnic version to mark inclusion of tx_flush bugfix. Signed-off-by: Brian Uchino <buchino@cisco.com> Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfc: fix hton24 macro to take expressions as argsJoe Eykholt2010-04-111-6/+11
| | | | | | | | | | | | | hton24(p + 3, value) would fail to compile because p + 3[0] is not a valid expression. Went ahead and converted hton24 and ntoh24 to inline functions, which is better because the parameters are evalutated only once. Signed-off-by: Joe Eykholt <jeykholt@cisco.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfc: remove unneeded variables in fc_exch_recv_req()Joe Eykholt2010-04-111-6/+0
| | | | | | | | | fc_exch_recv_req has variables eof, sof, and f_ctl, which are set but never used. Delete them. Signed-off-by: Joe Eykholt <jeykholt@cisco.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fcoe: check netif operstate instead of IFF_UP & link stateChris Leech2010-04-111-2/+1
| | | | | | | | | Allow for dormant states while link configuration completes. In the default link mode, this is equivalent to the old check. Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] fcoe: reset FIP ctlr link state on disable/enableChris Leech2010-04-111-4/+7
| | | | | | | | | | | | | The FIP controler state wasn't being reset on a disable. A disable/enable sequence should be treated as a link event. Otherwise, when using disable to mask a time when the link is up but unusable, FCF discovery would attempt to continue and login would jump directly to the non-FIP fallback on enable. Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] libfcoe: Don't fill MAC desc in FLOGI if FIP negotiated FPMARobert Love2010-04-111-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FPMA indicates that the Fabric will provide the host's N_Port's MAC address. When sending a FLOGI/FDISC frame and FPMA was negotiated through FIP discovery we still need to provide the MAC descriptor, as per the specification, but the MAC should be zero'd out since the FCF will be providing it in the FLOGI/FDISC ACC. In FC-BB-5 section 7.8.7.4.2 (Fabric login) it states: The MAC address field in the MAC address descriptor of a FIP FLOGI Request operation or a FIP NPIV FDISC Request operation shall contain: a) the proposed MAC address to use as VN_Port MAC address if the ENode is requesting to use SPMA (see table 27); b) all zeroes to indicate no MAC address is proposed if the ENode is requesting to use FPMA (see table 27); or c) the proposed MAC address to use as VN_Port MAC address if the ENode supports both SPMA and FPMA and leaves the decision of which addressing scheme to use to the FCF (i.e., if both the FP and SP bits are set to one, see table 27). This patch fixes case B. This patch also adds debug statements to illustrate whether a FPMA or SPMA MAC is added to a FLOGI/FDISC frame. Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Bump version 05.100.00.02Kashyap, Desai2010-04-111-2/+2
| | | | | | | Upgrade version to 05.100.00.02 Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Before removing sas_device search device in list for ↵Kashyap, Desai2010-04-111-3/+8
| | | | | | | | | | | | | | | _scsih_sas_device_remove Fix a oops in _scsih_sas_device_remove. The driver was attempting to delete a object from the sas_device link list when the object was not present. Added sanity check for sas_device NULL dereference. before deleting sas_device now driver will search device in list then only it will follow device removal. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Reworked scmd->result priority for _scsih_qcmd.Kashyap, Desai2010-04-111-7/+14
| | | | | | | | | | | | | | | | | | | we added support to set the deleted flag prior to device scan, then clear the flag for responding devices, leaving the deleted flag only set for missing devices. The problem is for internal generated host resets, IO queues are not blocked at scsi mid layer level. IO will be continued sent to driver, and driver will return SCSI_MLQUEUE_HOST_BUSY. The problem is the driver checks for the deleted flag before it checks for the controller being in reset, so there is a window where the driver would be returning DID_NO_CONNECT for responding devices. This occurs during the time between calling _scsih_prep_device_scan, and _scsih_mark_responding_sas_device & _scsih_mark_responding_raid_device. Fix the queuecommand entry point so ioc->shost_recovery flag sanity check is given higher presidence then the device "deleted flag" check. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: Update Driver version to 8.3.12James Smart2010-04-111-1/+1
| | | | | | Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: Fix discovery issuesJames Smart2010-04-117-5/+105
| | | | | | | | | | - Add code to prevent unreg_vpi mailbox command from failing. - Add code to reset the HBA if unreg_vpi mailbox fails with busy status. - Remove code that was clearing the nlp_type stored during rport discovery. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: BSG Fixes and enhancementsJames Smart2010-04-114-39/+253
| | | | | | | | | | | | | | | - Add memcpy to mailbox completion to transfer reply correctly. - Add support for BSG mailbox commands (dump, update_cfg, and event_log_status). - Add warning message and refuse mailbox command while mgmt is blocked. - Add checks for memory allocation failure. - Add check for sli4 dump zero BDE size. - Only copy data if mailbox commands succeed. - Add support for Read Event Log mailbox command. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: Critical fixesJames Smart2010-04-116-35/+56
| | | | | | | | | | | | - Move the code to increase the sg seg count for LP21000 adapters. - Check pcmd on command completion before dereferencing it. - Clear queue memory when creating firmware queues to prevent stale entries. - Replace the use of PAGE_SIZE in many areas that assumed it was always 4k. - Add an else clause to a conditional that needed to unlock the hba_lock. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: T10-PI/DIF changesJames Smart2010-04-112-139/+177
| | | | | | | | | | | Update driver for change in T10-PI interface on adapter - Remove Profiles. - Add new SLI Opcodes. - Add new PDE structures used for BlockGuard. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: Miscellaneous ChangesJames Smart2010-04-112-7/+15
| | | | | | | | | | - Prevent log message 1801 during vport delete. - Enable NPIV by default. - Display correct value for max Vports on SLI4 HBAs. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] lpfc 8.3.12: Emulex SLI enhancementsJames Smart2010-04-117-20/+187
| | | | | | | | | - Add the new Logical Link speed event support. - Add RATOV and EDTOV to the REG_VFI mailbox command. Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Upgrade version 05.100.00.01Kashyap, Desai2010-04-111-2/+2
| | | | | | | Upgraded version string. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Check for NULL pointer before free_pages is added.Kashyap, Desai2010-04-111-1/+4
| | | | | | | Added check before free_pages just to make sure ioc->scsi_lookup is not NULL. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Added support for PCIe Advanced Error Recovery.Kashyap, Desai2010-04-112-0/+124
| | | | | | | | | | | | Added support in the driver to support EEH and PCIe Advanced Error Recovery. This involves adding new pci_error_handler interface for recovering the controller from PCI Bus errors, such as SERR and PERR. Some tools are available for simulating PCI errors in order to validate this interface: http://www.kernel.org/pub/linux/utils/pci/aer-inject Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: Send default descriptor for RAID pass through in mpt2ctlKashyap, Desai2010-04-111-2/+5
| | | | | | | | RAID_SCSI_IO_PASSTHROUGH: Driver needs to be sending the default descriptor for RAID Passthru, currently its sending SCSI_IO descriptor. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas: sanity added to remove duplicate port from topologyKashyap, Desai2010-04-112-0/+86
| | | | | | | | | | | | | | | | | | | | | | | | | There are few special cases which needs to be handled deleting old port. CASE1: In topology you need cascaded expanders. Through sysfs just make sure topology is up. Erase the manufacturing image of the cascaded expander and reset the board. In some cases Adapter will receive Exapnder Add event before expander delete. In such a case, driver needs to delete duplicate port before adding new port. CASE2: Enable Device Missing delay of HBA through lsiutils. If expander or end device is hotswapped with different device before DMD timer expires, driver will get device add for new device first and then device deletion event for the original devices will arrive later at DMD timer expires. In this case also driver need to delete duplicate port before adding port for new device. Added new function which will make sure when new port is added, that its not claiming the same phy resources already in use by another port. If it does, then it will delete the other port before adding the new port. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] scsi_debug: add max_queue + no_uld parametersDouglas Gilbert2010-04-111-16/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | While testing the midlevel q_at_head and q_at_tail patch for sg and the block SG_IO ioctl I found it useful to reduce the queuing within the scsi_debug driver. The reason is that the midlevel queue only comes into play when the corresponding LLD queue is full. It is also useful when testing to be confident that your program is the only thing issuing commands to the (virtual) scsi_debug device. The no_uld=1 parameter will stop a scsi_debug virtual disk appearing as /dev/sd* . Changelog: - add max_queue parameter to reduce the number of queued commands the driver will accept. This parameter can be changed after the driver is loaded. - add no_uld parameter that restricts scsi_debug's virtual devices to the sg and bsg drivers - correct stale url Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] sd: retry read_capacity on UNIT_ATTENTIONJames Bottomley2010-04-111-3/+20
| | | | | | | | | | | | | Hazard testing uncovered yet another bug in sd. Under heavy reset activity the retry counter might be exhausted and the command will be returned with sense UNIT_ATTENTION/0x29/00 (POWER ON, RESET, OR BUS DEVICE RESET OCCURRED). In those cases we should just increase the retry counter again, retrying one more to clear up this Unit Attention state. [jejb: update to work with RC16 devices and not to loop endlessly] Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] mpt2sas : IOs needs to be pause until handles are refreshed for all ↵Kashyap, Desai2010-04-111-9/+40
| | | | | | | | | | | | | | | | | | | | device after recovery After Host Reset firmware will have new list of device handles for the target. Device handle refresh in driver is part of Rescan topology logic. (See functions like *_search_responding_*). This needs to be done from Host Reset context before making shost_recovery to 0. Currently it is done in Firwmare event context, which may leads IO to a wrong device. Now handler refresh is moved to HBA reset context. Apart from this, Now driver will stop IOs for all device setting deleted flag to 1 at the time of HBA Reset through _scsih_prep_device_scan. It will only unblock devices, if devices has been found as part of RESCAN. This way it will make more safe IO blocking at the time of HBA reset at mpt2sas driver layer. Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] sd: quiet spurious error messages in READ_CAPACITY(16)Hannes Reinecke2010-04-111-0/+2
| | | | | | | | | | | | sd always tries to submit a READ_CAPACITY(16) CDB, regardless whether the host actually supports it. queuecommand() will then return DID_ABORT, which is not qualified enough to detect the true cause here. So better check in sd_try_rc16 first if the cdblen is supported. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bnx2i: Update version and module descriptionAnil Veerabhadrappa2010-04-111-3/+4
| | | | | | | | missing 10G drivers added to description Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bnx2i: link bnx2i hba and cnic device before registering the deviceAnil Veerabhadrappa2010-04-111-2/+2
| | | | | | | | | | | | | | | | | When bnx2/cnic/bnx2i drivers are loaded in certain order, bnx2i will will not initialize the device correctly because 'hba->cnic' will be NULL when bnx2i_start() is called from register_device() context. Under this condition 'ifdown' and 'ifup' of associated network interface is required to bring iscsi adapter state to ready state so that it will accept iscsi connection setup within the chip Initializing 'hba->cnic' before calling register_device() will fix this issue Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bnx2i: make firmware use statsn field when constructing headerAnil Veerabhadrappa2010-04-111-1/+1
| | | | | | | | | | | | | instruct firmware to use driver/iscsid provided expected statsn field while constructing login pdu header. Initialize 'flags' to instruct chip to use driver/iscsid provided ExpStatSN value while constructing iSCSI login PDU header Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi ehChristof Schmitt2010-04-111-5/+13
| | | | | | | | | | The return code FAST_IO_FAIL from fc_block_scsi_eh indicates that the pending I/O requests have been terminated as a result of the fast_io_fail_tmo. Pass this return code back to the scsi eh to stop the scsi eh in this case. Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] Allow FC LLD to fast-fail scsi eh by introducing new eh returnChristof Schmitt2010-04-114-11/+27
| | | | | | | | | | | | | | | | | | | | | | | If the scsi eh is running and then a FC LLD calls fc_remote_port_delete, the SCSI commands sent from the eh will fail. To prevent this, a FC LLD can call fc_block_scsi_eh from the eh callback, blocking the eh thread until the dev_loss_tmo fires or the remote port is available again. If (e.g. for a multipathing setup) the dev_loss_tmo is set to a very large value, thus preventing the scsi device removal , the scsi eh can block for a long time. For multipathing, the fast_io_fail_tmo is then set to a low value to detect path problems sooner. This patch introduces a new return code FAST_IO_FAIL. The function fc_block_scsi_eh now returns FAST_IO_FAIL when the fast_io_fail_tmo fires. This indicates that the LLD terminated all pending I/O requests and there are no more pending SCSI commands for the scsi eh to wait for. This return code can be passed back to the scsi eh to stop the escalation and finish the recovery process for this device. Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: Fix documentation of ql2xfdmienable module parameterFerenc Wagner2010-04-111-2/+2
| | | | | | | | The default is enabled since 7e47e5ca184548341a82eeb2238ee3622c43cae1. Signed-off-by: Ferenc Wagner <wferi@niif.hu> Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: General checkpatch corrections.Andrew Vasquez2010-04-115-60/+69
| | | | | Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: Fix to make conditional decision based on port number.Sarang Radke2010-04-111-2/+2
| | | | | Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: Free DMA memory only if it is allocated in vendor specific ↵Harish Zunjarrao2010-04-111-2/+4
| | | | | | | | | | | | BSG command The qla84xx_mgmt_cmd function supports multiple subcommands. Some subcommands require DMA memory and some do not. Therefore check before freeing DMA memory whether it is allocated or not. Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: Add APEX support.Sarang Radke2010-04-117-4/+518
| | | | | | | Allows priority setting for FCP_CMNDs. Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] qla2xxx: Re-organized BSG interface specific code.Giridhar Malavali2010-04-117-831/+1230
| | | | | | | | | | | | | | | 1. Segregate BSG interface specific code to new files. 2. Handle multiple vendor specific commands indepedently. 3. Reorganised support for reset, management and update FCoE firmware commands. 4. Fixed memory leak issue in Loopback. 5. Added new vendor command to support iiDMA using BSG interface. 6. Proper cleanup of dma mapped and dma allocated buffers for BSG request. [jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch] Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* [SCSI] bfa: sg addr big endian fixJing Huang2010-04-112-2/+17
| | | | | | | | sg address in IO request is not set up correctly for big endian platform. add new macros to properly swap the address. Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
OpenPOWER on IntegriCloud