diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/usb.h | 12 | ||||
| -rw-r--r-- | include/linux/usb/composite.h | 338 | ||||
| -rw-r--r-- | include/linux/usb/gadget.h | 27 | ||||
| -rw-r--r-- | include/linux/usb/irda.h | 151 | ||||
| -rw-r--r-- | include/linux/usbdevice_fs.h | 2 |
5 files changed, 521 insertions, 9 deletions
diff --git a/include/linux/usb.h b/include/linux/usb.h index c08689ea9b4b..5811c5da69f9 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -160,6 +160,7 @@ struct usb_interface { unsigned is_active:1; /* the interface is not suspended */ unsigned sysfs_files_created:1; /* the sysfs attributes exist */ unsigned needs_remote_wakeup:1; /* driver requires remote wakeup */ + unsigned needs_binding:1; /* needs delayed unbind/rebind */ struct device dev; /* interface specific device info */ struct device *usb_dev; @@ -293,7 +294,7 @@ struct usb_devmap { struct usb_bus { struct device *controller; /* host/master side hardware */ int busnum; /* Bus number (in order of reg) */ - char *bus_name; /* stable id (PCI slot_name etc) */ + const char *bus_name; /* stable id (PCI slot_name etc) */ u8 uses_dma; /* Does the host controller use DMA? */ u8 otg_port; /* 0, or number of OTG/HNP port */ unsigned is_b_host:1; /* true during some HNP roleswitches */ @@ -497,8 +498,6 @@ extern int usb_lock_device_for_reset(struct usb_device *udev, /* USB port reset for device reinitialization */ extern int usb_reset_device(struct usb_device *dev); -extern int usb_reset_composite_device(struct usb_device *dev, - struct usb_interface *iface); extern struct usb_device *usb_find_device(u16 vendor_id, u16 product_id); @@ -958,9 +957,9 @@ struct usbdrv_wrap { * @resume: Called when the device is being resumed by the system. * @reset_resume: Called when the suspended device has been reset instead * of being resumed. - * @pre_reset: Called by usb_reset_composite_device() when the device + * @pre_reset: Called by usb_reset_device() when the device * is about to be reset. - * @post_reset: Called by usb_reset_composite_device() after the device + * @post_reset: Called by usb_reset_device() after the device * has been reset * @id_table: USB drivers use ID table to support hotplugging. * Export this with MODULE_DEVICE_TABLE(usb,...). This must be set @@ -972,6 +971,8 @@ struct usbdrv_wrap { * added to this driver by preventing the sysfs file from being created. * @supports_autosuspend: if set to 0, the USB core will not allow autosuspend * for interfaces bound to this driver. + * @soft_unbind: if set to 1, the USB core will not kill URBs and disable + * endpoints before calling the driver's disconnect method. * * USB interface drivers must provide a name, probe() and disconnect() * methods, and an id_table. Other driver fields are optional. @@ -1012,6 +1013,7 @@ struct usb_driver { struct usbdrv_wrap drvwrap; unsigned int no_dynamic_id:1; unsigned int supports_autosuspend:1; + unsigned int soft_unbind:1; }; #define to_usb_driver(d) container_of(d, struct usb_driver, drvwrap.driver) diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h new file mode 100644 index 000000000000..747c3a49cdc9 --- /dev/null +++ b/include/linux/usb/composite.h @@ -0,0 +1,338 @@ +/* + * composite.h -- framework for usb gadgets which are composite devices + * + * Copyright (C) 2006-2008 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __LINUX_USB_COMPOSITE_H +#define __LINUX_USB_COMPOSITE_H + +/* + * This framework is an optional layer on top of the USB Gadget interface, + * making it easier to build (a) Composite devices, supporting multiple + * functions within any single configuration, and (b) Multi-configuration + * devices, also supporting multiple functions but without necessarily + * having more than one function per configuration. + * + * Example: a device with a single configuration supporting both network + * link and mass storage functions is a composite device. Those functions + * might alternatively be packaged in individual configurations, but in + * the composite model the host can use both functions at the same time. + */ + +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> + + +struct usb_configuration; + +/** + * struct usb_function - describes one function of a configuration + * @name: For diagnostics, identifies the function. + * @strings: tables of strings, keyed by identifiers assigned during bind() + * and by language IDs provided in control requests + * @descriptors: Table of full (or low) speed descriptors, using interface and + * string identifiers assigned during @bind(). If this pointer is null, + * the function will not be available at full speed (or at low speed). + * @hs_descriptors: Table of high speed descriptors, using interface and + * string identifiers assigned during @bind(). If this pointer is null, + * the function will not be available at high speed. + * @config: assigned when @usb_add_function() is called; this is the + * configuration with which this function is associated. + * @bind: Before the gadget can register, all of its functions bind() to the + * available resources including string and interface identifiers used + * in interface or class descriptors; endpoints; I/O buffers; and so on. + * @unbind: Reverses @bind; called as a side effect of unregistering the + * driver which added this function. + * @set_alt: (REQUIRED) Reconfigures altsettings; function drivers may + * initialize usb_ep.driver data at this time (when it is used). + * Note that setting an interface to its current altsetting resets + * interface state, and that all interfaces have a disabled state. + * @get_alt: Returns the active altsetting. If this is not provided, + * then only altsetting zero is supported. + * @disable: (REQUIRED) Indicates the function should be disabled. Reasons + * include host resetting or reconfiguring the gadget, and disconnection. + * @setup: Used for interface-specific control requests. + * @suspend: Notifies functions when the host stops sending USB traffic. + * @resume: Notifies functions when the host restarts USB traffic. + * + * A single USB function uses one or more interfaces, and should in most + * cases support operation at both full and high speeds. Each function is + * associated by @usb_add_function() with a one configuration; that function + * causes @bind() to be called so resources can be allocated as part of + * setting up a gadget driver. Those resources include endpoints, which + * should be allocated using @usb_ep_autoconfig(). + * + * To support dual speed operation, a function driver provides descriptors + * for both high and full speed operation. Except in rare cases that don't + * involve bulk endpoints, each speed needs different endpoint descriptors. + * + * Function drivers choose their own strategies for managing instance data. + * The simplest strategy just declares it "static', which means the function + * can only be activated once. If the function needs to be exposed in more + * than one configuration at a given speed, it needs to support multiple + * usb_function structures (one for each configuration). + * + * A more complex strategy might encapsulate a @usb_function structure inside + * a driver-specific instance structure to allows multiple activations. An + * example of multiple activations might be a CDC ACM function that supports + * two or more distinct instances within the same configuration, providing + * several independent logical data links to a USB host. + */ +struct usb_function { + const char *name; + struct usb_gadget_strings **strings; + struct usb_descriptor_header **descriptors; + struct usb_descriptor_header **hs_descriptors; + + struct usb_configuration *config; + + /* REVISIT: bind() functions can be marked __init, which + * makes trouble for section mismatch analysis. See if + * we can't restructure things to avoid mismatching. + * Related: unbind() may kfree() but bind() won't... + */ + + /* configuration management: bind/unbind */ + int (*bind)(struct usb_configuration *, + struct usb_function *); + void (*unbind)(struct usb_configuration *, + struct usb_function *); + + /* runtime state management */ + int (*set_alt)(struct usb_function *, + unsigned interface, unsigned alt); + int (*get_alt)(struct usb_function *, + unsigned interface); + void (*disable)(struct usb_function *); + int (*setup)(struct usb_function *, + const struct usb_ctrlrequest *); + void (*suspend)(struct usb_function *); + void (*resume)(struct usb_function *); + + /* internals */ + struct list_head list; +}; + +int usb_add_function(struct usb_configuration *, struct usb_function *); + +int usb_interface_id(struct usb_configuration *, struct usb_function *); + +/** + * ep_choose - select descriptor endpoint at current device speed + * @g: gadget, connected and running at some speed + * @hs: descriptor to use for high speed operation + * @fs: descriptor to use for full or low speed operation + */ +static inline struct usb_endpoint_descriptor * +ep_choose(struct usb_gadget *g, struct usb_endpoint_descriptor *hs, + struct usb_endpoint_descriptor *fs) +{ + if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) + return hs; + return fs; +} + +#define MAX_CONFIG_INTERFACES 16 /* arbitrary; max 255 */ + +/** + * struct usb_configuration - represents one gadget configuration + * @label: For diagnostics, describes the configuration. + * @strings: Tables of strings, keyed by identifiers assigned during @bind() + * and by language IDs provided in control requests. + * @descriptors: Table of descriptors preceding all function descriptors. + * Examples include OTG and vendor-specific descriptors. + * @bind: Called from @usb_add_config() to allocate resources unique to this + * configuration and to call @usb_add_function() for each function used. + * @unbind: Reverses @bind; called as a side effect of unregistering the + * driver which added this configuration. + * @setup: Used to delegate control requests that aren't handled by standard + * device infrastructure or directed at a specific interface. + * @bConfigurationValue: Copied into configuration descriptor. + * @iConfiguration: Copied into configuration descriptor. + * @bmAttributes: Copied into configuration descriptor. + * @bMaxPower: Copied into configuration descriptor. + * @cdev: assigned by @usb_add_config() before calling @bind(); this is + * the device associated with this configuration. + * + * Configurations are building blocks for gadget drivers structured around + * function drivers. Simple USB gadgets require only one function and one + * configuration, and handle dual-speed hardware by always providing the same + * functionality. Slightly more complex gadgets may have more than one + * single-function configuration at a given speed; or have configurations + * that only work at one speed. + * + * Composite devices are, by definition, ones with configurations which + * include more than one function. + * + * The lifecycle of a usb_configuration includes allocation, initialization + * of the fields described above, and calling @usb_add_config() to set up + * internal data and bind it to a specific device. The configuration's + * @bind() method is then used to initialize all the functions and then + * call @usb_add_function() for them. + * + * Those functions would normally be independant of each other, but that's + * not mandatory. CDC WMC devices are an example where functions often + * depend on other functions, with some functions subsidiary to others. + * Such interdependency may be managed in any way, so long as all of the + * descriptors complete by the time the composite driver returns from + * its bind() routine. + */ +struct usb_configuration { + const char *label; + struct usb_gadget_strings **strings; + const struct usb_descriptor_header **descriptors; + + /* REVISIT: bind() functions can be marked __init, which + * makes trouble for section mismatch analysis. See if + * we can't restructure things to avoid mismatching... + */ + + /* configuration management: bind/unbind */ + int (*bind)(struct usb_configuration *); + void (*unbind)(struct usb_configuration *); + int (*setup)(struct usb_configuration *, + const struct usb_ctrlrequest *); + + /* fields in the config descriptor */ + u8 bConfigurationValue; + u8 iConfiguration; + u8 bmAttributes; + u8 bMaxPower; + + struct usb_composite_dev *cdev; + + /* internals */ + struct list_head list; + struct list_head functions; + u8 next_interface_id; + unsigned highspeed:1; + unsigned fullspeed:1; + struct usb_function *interface[MAX_CONFIG_INTERFACES]; +}; + +int usb_add_config(struct usb_composite_dev *, + struct usb_configuration *); + +/** + * struct usb_composite_driver - groups configurations into a gadget + * @name: For diagnostics, identifies the driver. + * @dev: Template descriptor for the device, including default device + * identifiers. + * @strings: tables of strings, keyed by identifiers assigned during bind() + * and language IDs provided in control requests + * @bind: (REQUIRED) Used to allocate resources that are shared across the + * whole device, such as string IDs, and add its configurations using + * @usb_add_config(). This may fail by returning a negative errno + * value; it should return zero on successful initialization. + * @unbind: Reverses @bind(); called as a side effect of unregistering + * this driver. + * + * Devices default to reporting self powered operation. Devices which rely + * on bus powered operation should report this in their @bind() method. + * + * Before returning from @bind, various fields in the template descriptor + * may be overridden. These include the idVendor/idProduct/bcdDevice values + * normally to bind the appropriate host side driver, and the three strings + * (iManufacturer, iProduct, iSerialNumber) normally used to provide user + * meaningful device identifiers. (The strings will not be defined unless + * they are defined in @dev and @strings.) The correct ep0 maxpacket size + * is also reported, as defined by the underlying controller driver. + */ +struct usb_composite_driver { + const char *name; + const struct usb_device_descriptor *dev; + struct usb_gadget_strings **strings; + + /* REVISIT: bind() functions can be marked __init, which + * makes trouble for section mismatch analysis. See if + * we can't restructure things to avoid mismatching... + */ + + int (*bind)(struct usb_composite_dev *); + int (*unbind)(struct usb_composite_dev *); +}; + +extern int usb_composite_register(struct usb_composite_driver *); +extern void usb_composite_unregister(struct usb_composite_driver *); + + +/** + * struct usb_composite_device - represents one composite usb gadget + * @gadget: read-only, abstracts the gadget's usb peripheral controller + * @req: used for control responses; buffer is pre-allocated + * @bufsiz: size of buffer pre-allocated in @req + * @config: the currently active configuration + * + * One of these devices is allocated and initialized before the + * associated device driver's bind() is called. + * + * OPEN ISSUE: it appears that some WUSB devices will need to be + * built by combining a normal (wired) gadget with a wireless one. + * This revision of the gadget framework should probably try to make + * sure doing that won't hurt too much. + * + * One notion for how to handle Wireless USB devices involves: + * (a) a second gadget here, discovery mechanism TBD, but likely + * needing separate "register/unregister WUSB gadget" calls; + * (b) updates to usb_gadget to include flags "is it wireless", + * "is it wired", plus (presumably in a wrapper structure) + * bandgroup and PHY info; + * (c) presumably a wireless_ep wrapping a usb_ep, and reporting + * wireless-specific parameters like maxburst and maxsequence; + * (d) configurations that are specific to wireless links; + * (e) function drivers that understand wireless configs and will + * support wireless for (additional) function instances; + * (f) a function to support association setup (like CBAF), not + * necessarily requiring a wireless adapter; + * (g) composite device setup that can create one or more wireless + * configs, including appropriate association setup support; + * (h) more, TBD. + */ +struct usb_composite_dev { + struct usb_gadget *gadget; + struct usb_request *req; + unsigned bufsiz; + + struct usb_configuration *config; + + /* internals */ + struct usb_device_descriptor desc; + struct list_head configs; + struct usb_composite_driver *driver; + u8 next_string_id; + + spinlock_t lock; + + /* REVISIT use and existence of lock ... */ +}; + +extern int usb_string_id(struct usb_composite_dev *c); + +/* messaging utils */ +#define DBG(d, fmt, args...) \ + dev_dbg(&(d)->gadget->dev , fmt , ## args) +#define VDBG(d, fmt, args...) \ + dev_vdbg(&(d)->gadget->dev , fmt , ## args) +#define ERROR(d, fmt, args...) \ + dev_err(&(d)->gadget->dev , fmt , ## args) +#define WARN(d, fmt, args...) \ + dev_warn(&(d)->gadget->dev , fmt , ## args) +#define INFO(d, fmt, args...) \ + dev_info(&(d)->gadget->dev , fmt , ## args) + +#endif /* __LINUX_USB_COMPOSITE_H */ diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h index cf468fbdbf8e..0460a746480c 100644 --- a/include/linux/usb/gadget.h +++ b/include/linux/usb/gadget.h @@ -33,7 +33,8 @@ struct usb_ep; * @short_not_ok: When reading data, makes short packets be * treated as errors (queue stops advancing till cleanup). * @complete: Function called when request completes, so this request and - * its buffer may be re-used. + * its buffer may be re-used. The function will always be called with + * interrupts disabled, and it must not sleep. * Reads terminate with a short packet, or when the buffer fills, * whichever comes first. When writes terminate, some data bytes * will usually still be in flight (often in a hardware fifo). @@ -271,7 +272,10 @@ static inline void usb_ep_free_request(struct usb_ep *ep, * (Note that some USB device controllers disallow protocol stall responses * in some cases.) When control responses are deferred (the response is * written after the setup callback returns), then usb_ep_set_halt() may be - * used on ep0 to trigger protocol stalls. + * used on ep0 to trigger protocol stalls. Depending on the controller, + * it may not be possible to trigger a status-stage protocol stall when the + * data stage is over, that is, from within the response's completion + * routine. * * For periodic endpoints, like interrupt or isochronous ones, the usb host * arranges to poll once per interval, and the gadget driver usually will @@ -858,6 +862,25 @@ int usb_descriptor_fillbuf(void *, unsigned, int usb_gadget_config_buf(const struct usb_config_descriptor *config, void *buf, unsigned buflen, const struct usb_descriptor_header **desc); +/* copy a NULL-terminated vector of descriptors */ +struct usb_descriptor_header **usb_copy_descriptors( + struct usb_descriptor_header **); + +/* return copy of endpoint descriptor given original descriptor set */ +struct usb_endpoint_descriptor *usb_find_endpoint( + struct usb_descriptor_header **src, + struct usb_descriptor_header **copy, + struct usb_endpoint_descriptor *match); + +/** + * usb_free_descriptors - free descriptors returned by usb_copy_descriptors() + * @v: vector of descriptors + */ +static inline void usb_free_descriptors(struct usb_descriptor_header **v) +{ + kfree(v); +} + /*-------------------------------------------------------------------------*/ /* utility wrapping a simple endpoint selection policy */ diff --git a/include/linux/usb/irda.h b/include/linux/usb/irda.h new file mode 100644 index 000000000000..e345ceaf72d6 --- /dev/null +++ b/include/linux/usb/irda.h @@ -0,0 +1,151 @@ +/* + * USB IrDA Bridge Device Definition + */ + +#ifndef __LINUX_USB_IRDA_H +#define __LINUX_USB_IRDA_H + +/* This device should use Application-specific class */ + +#define USB_SUBCLASS_IRDA 0x02 + +/*-------------------------------------------------------------------------*/ + +/* Class-Specific requests (bRequest field) */ + +#define USB_REQ_CS_IRDA_RECEIVING 1 +#define USB_REQ_CS_IRDA_CHECK_MEDIA_BUSY 3 +#define USB_REQ_CS_IRDA_RATE_SNIFF 4 +#define USB_REQ_CS_IRDA_UNICAST_LIST 5 +#define USB_REQ_CS_IRDA_GET_CLASS_DESC 6 + +/*-------------------------------------------------------------------------*/ + +/* Class-Specific descriptor */ + +#define USB_DT_CS_IRDA 0x21 + +/*-------------------------------------------------------------------------*/ + +/* Data sizes */ + +#define USB_IRDA_DS_2048 (1 << 5) +#define USB_IRDA_DS_1024 (1 << 4) +#define USB_IRDA_DS_512 (1 << 3) +#define USB_IRDA_DS_256 (1 << 2) +#define USB_IRDA_DS_128 (1 << 1) +#define USB_IRDA_DS_64 (1 << 0) + +/* Window sizes */ + +#define USB_IRDA_WS_7 (1 << 6) +#define USB_IRDA_WS_6 (1 << 5) +#define USB_IRDA_WS_5 (1 << 4) +#define USB_IRDA_WS_4 (1 << 3) +#define USB_IRDA_WS_3 (1 << 2) +#define USB_IRDA_WS_2 (1 << 1) +#define USB_IRDA_WS_1 (1 << 0) + +/* Min turnaround times in usecs */ + +#define USB_IRDA_MTT_0 (1 << 7) +#define USB_IRDA_MTT_10 (1 << 6) +#define USB_IRDA_MTT_50 (1 << 5) +#define USB_IRDA_MTT_100 (1 << 4) +#define USB_IRDA_MTT_500 (1 << 3) +#define USB_IRDA_MTT_1000 (1 << 2) +#define USB_IRDA_MTT_5000 (1 << 1) +#define USB_IRDA_MTT_10000 (1 << 0) + +/* Baud rates */ + +#define USB_IRDA_BR_4000000 (1 << 8) +#define USB_IRDA_BR_1152000 (1 << 7) +#define USB_IRDA_BR_576000 (1 << 6) +#define USB_IRDA_BR_115200 (1 << 5) +#define USB_IRDA_BR_57600 (1 << 4) +#define USB_IRDA_BR_38400 (1 << 3) +#define USB_IRDA_BR_19200 (1 << 2) +#define USB_IRDA_BR_9600 (1 << 1) +#define USB_IRDA_BR_2400 (1 << 0) + +/* Additional BOFs */ + +#define USB_IRDA_AB_0 (1 << 7) +#define USB_IRDA_AB_1 (1 << 6) +#define USB_IRDA_AB_2 (1 << 5) +#define USB_IRDA_AB_3 (1 << 4) +#define USB_IRDA_AB_6 (1 << 3) +#define USB_IRDA_AB_12 (1 << 2) +#define USB_IRDA_AB_24 (1 << 1) +#define USB_IRDA_AB_48 (1 << 0) + +/* IRDA Rate Sniff */ + +#define USB_IRDA_RATE_SNIFF 1 + +/*-------------------------------------------------------------------------*/ + +struct usb_irda_cs_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __le16 bcdSpecRevision; + __u8 bmDataSize; + __u8 bmWindowSize; + __u8 bmMinTurnaroundTime; + __le16 wBaudRate; + __u8 bmAdditionalBOFs; + __u8 bIrdaRateSniff; + __u8 bMaxUnicastList; +} __attribute__ ((packed)); + +/*-------------------------------------------------------------------------*/ + +/* Data Format */ + +#define USB_IRDA_STATUS_MEDIA_BUSY (1 << 7) + +/* The following is a 4-bit value used for both + * inbound and outbound headers: + * + * 0 - speed ignored + * 1 - 2400 bps + * 2 - 9600 bps + * 3 - 19200 bps + * 4 - 38400 bps + * 5 - 57600 bps + * 6 - 115200 bps + * 7 - 576000 bps + * 8 - 1.152 Mbps + * 9 - 5 mbps + * 10..15 - Reserved + */ +#define USB_IRDA_STATUS_LINK_SPEED 0x0f + +/* The following is a 4-bit value used only for + * outbound header: + * + * 0 - No change (BOF ignored) + * 1 - 48 BOFs + * 2 - 24 BOFs + * 3 - 12 BOFs + * 4 - 6 BOFs + * 5 - 3 BOFs + * 6 - 2 BOFs + * 7 - 1 BOFs + * 8 - 0 BOFs + * 9..15 - Reserved + */ +#define USB_IRDA_EXTRA_BOFS 0xf0 + +struct usb_irda_inbound_header { + __u8 bmStatus; +}; + +struct usb_irda_outbound_header { + __u8 bmChange; +}; + +#endif /* __LINUX_USB_IRDA_H */ + diff --git a/include/linux/usbdevice_fs.h b/include/linux/usbdevice_fs.h index 3118ede2c67b..0044d9b4cb85 100644 --- a/include/linux/usbdevice_fs.h +++ b/include/linux/usbdevice_fs.h @@ -22,8 +22,6 @@ * * History: * 0.1 04.01.2000 Created - * - * $Id: usbdevice_fs.h,v 1.1 2000/01/06 18:40:41 tom Exp $ */ /*****************************************************************************/ |
