diff options
Diffstat (limited to 'include/linux')
26 files changed, 691 insertions, 68 deletions
diff --git a/include/linux/atmel-mci.h b/include/linux/atmel-mci.h index 91b77f8d495d..9177947bf032 100644 --- a/include/linux/atmel-mci.h +++ b/include/linux/atmel-mci.h @@ -11,6 +11,7 @@ * @detect_pin: GPIO pin wired to the card detect switch * @wp_pin: GPIO pin wired to the write protect sensor * @detect_is_active_high: The state of the detect pin when it is active + * @non_removable: The slot is not removable, only detect once * * If a given slot is not present on the board, @bus_width should be * set to 0. The other fields are ignored in this case. @@ -26,6 +27,7 @@ struct mci_slot_pdata { int detect_pin; int wp_pin; bool detect_is_active_high; + bool non_removable; }; /** diff --git a/include/linux/edac.h b/include/linux/edac.h index e1e68da6f35c..da3b72e95db3 100644 --- a/include/linux/edac.h +++ b/include/linux/edac.h @@ -194,7 +194,8 @@ static inline char *mc_event_error_type(const unsigned int err_type) * @MEM_DDR3: DDR3 RAM * @MEM_RDDR3: Registered DDR3 RAM * This is a variant of the DDR3 memories. - * @MEM_DDR4: DDR4 RAM + * @MEM_LRDDR3 Load-Reduced DDR3 memory. + * @MEM_DDR4: Unbuffered DDR4 RAM * @MEM_RDDR4: Registered DDR4 RAM * This is a variant of the DDR4 memories. */ @@ -216,6 +217,7 @@ enum mem_type { MEM_XDR, MEM_DDR3, MEM_RDDR3, + MEM_LRDDR3, MEM_DDR4, MEM_RDDR4, }; diff --git a/include/linux/mfd/abx500/ab8500-sysctrl.h b/include/linux/mfd/abx500/ab8500-sysctrl.h index adba89d9c660..689312745b2f 100644 --- a/include/linux/mfd/abx500/ab8500-sysctrl.h +++ b/include/linux/mfd/abx500/ab8500-sysctrl.h @@ -12,7 +12,6 @@ int ab8500_sysctrl_read(u16 reg, u8 *value); int ab8500_sysctrl_write(u16 reg, u8 mask, u8 value); -void ab8500_restart(char mode, const char *cmd); #else diff --git a/include/linux/mfd/arizona/registers.h b/include/linux/mfd/arizona/registers.h index c0b075f6bc35..aacc10d7789c 100644 --- a/include/linux/mfd/arizona/registers.h +++ b/include/linux/mfd/arizona/registers.h @@ -125,6 +125,8 @@ #define ARIZONA_MIC_BIAS_CTRL_1 0x218 #define ARIZONA_MIC_BIAS_CTRL_2 0x219 #define ARIZONA_MIC_BIAS_CTRL_3 0x21A +#define ARIZONA_HP_CTRL_1L 0x225 +#define ARIZONA_HP_CTRL_1R 0x226 #define ARIZONA_ACCESSORY_DETECT_MODE_1 0x293 #define ARIZONA_HEADPHONE_DETECT_1 0x29B #define ARIZONA_HEADPHONE_DETECT_2 0x29C @@ -279,8 +281,16 @@ #define ARIZONA_AIF2_FRAME_CTRL_2 0x548 #define ARIZONA_AIF2_FRAME_CTRL_3 0x549 #define ARIZONA_AIF2_FRAME_CTRL_4 0x54A +#define ARIZONA_AIF2_FRAME_CTRL_5 0x54B +#define ARIZONA_AIF2_FRAME_CTRL_6 0x54C +#define ARIZONA_AIF2_FRAME_CTRL_7 0x54D +#define ARIZONA_AIF2_FRAME_CTRL_8 0x54E #define ARIZONA_AIF2_FRAME_CTRL_11 0x551 #define ARIZONA_AIF2_FRAME_CTRL_12 0x552 +#define ARIZONA_AIF2_FRAME_CTRL_13 0x553 +#define ARIZONA_AIF2_FRAME_CTRL_14 0x554 +#define ARIZONA_AIF2_FRAME_CTRL_15 0x555 +#define ARIZONA_AIF2_FRAME_CTRL_16 0x556 #define ARIZONA_AIF2_TX_ENABLES 0x559 #define ARIZONA_AIF2_RX_ENABLES 0x55A #define ARIZONA_AIF2_FORCE_WRITE 0x55B @@ -2245,6 +2255,46 @@ #define ARIZONA_MICB3_ENA_WIDTH 1 /* MICB3_ENA */ /* + * R549 (0x225) - HP Ctrl 1L + */ +#define ARIZONA_RMV_SHRT_HP1L 0x4000 /* RMV_SHRT_HP1L */ +#define ARIZONA_RMV_SHRT_HP1L_MASK 0x4000 /* RMV_SHRT_HP1L */ +#define ARIZONA_RMV_SHRT_HP1L_SHIFT 14 /* RMV_SHRT_HP1L */ +#define ARIZONA_RMV_SHRT_HP1L_WIDTH 1 /* RMV_SHRT_HP1L */ +#define ARIZONA_HP1L_FLWR 0x0004 /* HP1L_FLWR */ +#define ARIZONA_HP1L_FLWR_MASK 0x0004 /* HP1L_FLWR */ +#define ARIZONA_HP1L_FLWR_SHIFT 2 /* HP1L_FLWR */ +#define ARIZONA_HP1L_FLWR_WIDTH 1 /* HP1L_FLWR */ +#define ARIZONA_HP1L_SHRTI 0x0002 /* HP1L_SHRTI */ +#define ARIZONA_HP1L_SHRTI_MASK 0x0002 /* HP1L_SHRTI */ +#define ARIZONA_HP1L_SHRTI_SHIFT 1 /* HP1L_SHRTI */ +#define ARIZONA_HP1L_SHRTI_WIDTH 1 /* HP1L_SHRTI */ +#define ARIZONA_HP1L_SHRTO 0x0001 /* HP1L_SHRTO */ +#define ARIZONA_HP1L_SHRTO_MASK 0x0001 /* HP1L_SHRTO */ +#define ARIZONA_HP1L_SHRTO_SHIFT 0 /* HP1L_SHRTO */ +#define ARIZONA_HP1L_SHRTO_WIDTH 1 /* HP1L_SHRTO */ + +/* + * R550 (0x226) - HP Ctrl 1R + */ +#define ARIZONA_RMV_SHRT_HP1R 0x4000 /* RMV_SHRT_HP1R */ +#define ARIZONA_RMV_SHRT_HP1R_MASK 0x4000 /* RMV_SHRT_HP1R */ +#define ARIZONA_RMV_SHRT_HP1R_SHIFT 14 /* RMV_SHRT_HP1R */ +#define ARIZONA_RMV_SHRT_HP1R_WIDTH 1 /* RMV_SHRT_HP1R */ +#define ARIZONA_HP1R_FLWR 0x0004 /* HP1R_FLWR */ +#define ARIZONA_HP1R_FLWR_MASK 0x0004 /* HP1R_FLWR */ +#define ARIZONA_HP1R_FLWR_SHIFT 2 /* HP1R_FLWR */ +#define ARIZONA_HP1R_FLWR_WIDTH 1 /* HP1R_FLWR */ +#define ARIZONA_HP1R_SHRTI 0x0002 /* HP1R_SHRTI */ +#define ARIZONA_HP1R_SHRTI_MASK 0x0002 /* HP1R_SHRTI */ +#define ARIZONA_HP1R_SHRTI_SHIFT 1 /* HP1R_SHRTI */ +#define ARIZONA_HP1R_SHRTI_WIDTH 1 /* HP1R_SHRTI */ +#define ARIZONA_HP1R_SHRTO 0x0001 /* HP1R_SHRTO */ +#define ARIZONA_HP1R_SHRTO_MASK 0x0001 /* HP1R_SHRTO */ +#define ARIZONA_HP1R_SHRTO_SHIFT 0 /* HP1R_SHRTO */ +#define ARIZONA_HP1R_SHRTO_WIDTH 1 /* HP1R_SHRTO */ + +/* * R659 (0x293) - Accessory Detect Mode 1 */ #define ARIZONA_ACCDET_SRC 0x2000 /* ACCDET_SRC */ diff --git a/include/linux/mfd/atmel-hlcdc.h b/include/linux/mfd/atmel-hlcdc.h new file mode 100644 index 000000000000..1279ab1644b5 --- /dev/null +++ b/include/linux/mfd/atmel-hlcdc.h @@ -0,0 +1,85 @@ +/* + * Copyright (C) 2014 Free Electrons + * Copyright (C) 2014 Atmel + * + * Author: Boris BREZILLON <boris.brezillon@free-electrons.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __LINUX_MFD_HLCDC_H +#define __LINUX_MFD_HLCDC_H + +#include <linux/clk.h> +#include <linux/regmap.h> + +#define ATMEL_HLCDC_CFG(i) ((i) * 0x4) +#define ATMEL_HLCDC_SIG_CFG LCDCFG(5) +#define ATMEL_HLCDC_HSPOL BIT(0) +#define ATMEL_HLCDC_VSPOL BIT(1) +#define ATMEL_HLCDC_VSPDLYS BIT(2) +#define ATMEL_HLCDC_VSPDLYE BIT(3) +#define ATMEL_HLCDC_DISPPOL BIT(4) +#define ATMEL_HLCDC_DITHER BIT(6) +#define ATMEL_HLCDC_DISPDLY BIT(7) +#define ATMEL_HLCDC_MODE_MASK GENMASK(9, 8) +#define ATMEL_HLCDC_PP BIT(10) +#define ATMEL_HLCDC_VSPSU BIT(12) +#define ATMEL_HLCDC_VSPHO BIT(13) +#define ATMEL_HLCDC_GUARDTIME_MASK GENMASK(20, 16) + +#define ATMEL_HLCDC_EN 0x20 +#define ATMEL_HLCDC_DIS 0x24 +#define ATMEL_HLCDC_SR 0x28 +#define ATMEL_HLCDC_IER 0x2c +#define ATMEL_HLCDC_IDR 0x30 +#define ATMEL_HLCDC_IMR 0x34 +#define ATMEL_HLCDC_ISR 0x38 + +#define ATMEL_HLCDC_CLKPOL BIT(0) +#define ATMEL_HLCDC_CLKSEL BIT(2) +#define ATMEL_HLCDC_CLKPWMSEL BIT(3) +#define ATMEL_HLCDC_CGDIS(i) BIT(8 + (i)) +#define ATMEL_HLCDC_CLKDIV_SHFT 16 +#define ATMEL_HLCDC_CLKDIV_MASK GENMASK(23, 16) +#define ATMEL_HLCDC_CLKDIV(div) ((div - 2) << ATMEL_HLCDC_CLKDIV_SHFT) + +#define ATMEL_HLCDC_PIXEL_CLK BIT(0) +#define ATMEL_HLCDC_SYNC BIT(1) +#define ATMEL_HLCDC_DISP BIT(2) +#define ATMEL_HLCDC_PWM BIT(3) +#define ATMEL_HLCDC_SIP BIT(4) + +#define ATMEL_HLCDC_SOF BIT(0) +#define ATMEL_HLCDC_SYNCDIS BIT(1) +#define ATMEL_HLCDC_FIFOERR BIT(4) +#define ATMEL_HLCDC_LAYER_STATUS(x) BIT((x) + 8) + +/** + * Structure shared by the MFD device and its subdevices. + * + * @regmap: register map used to access HLCDC IP registers + * @periph_clk: the hlcdc peripheral clock + * @sys_clk: the hlcdc system clock + * @slow_clk: the system slow clk + * @irq: the hlcdc irq + */ +struct atmel_hlcdc { + struct regmap *regmap; + struct clk *periph_clk; + struct clk *sys_clk; + struct clk *slow_clk; + int irq; +}; + +#endif /* __LINUX_MFD_HLCDC_H */ diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h index d0e31a2287ac..81589d176ae8 100644 --- a/include/linux/mfd/axp20x.h +++ b/include/linux/mfd/axp20x.h @@ -14,6 +14,8 @@ enum { AXP202_ID = 0, AXP209_ID, + AXP288_ID, + NR_AXP20X_VARIANTS, }; #define AXP20X_DATACACHE(m) (0x04 + (m)) @@ -49,11 +51,13 @@ enum { #define AXP20X_IRQ3_EN 0x42 #define AXP20X_IRQ4_EN 0x43 #define AXP20X_IRQ5_EN 0x44 +#define AXP20X_IRQ6_EN 0x45 #define AXP20X_IRQ1_STATE 0x48 #define AXP20X_IRQ2_STATE 0x49 #define AXP20X_IRQ3_STATE 0x4a #define AXP20X_IRQ4_STATE 0x4b #define AXP20X_IRQ5_STATE 0x4c +#define AXP20X_IRQ6_STATE 0x4d /* ADC */ #define AXP20X_ACIN_V_ADC_H 0x56 @@ -116,6 +120,15 @@ enum { #define AXP20X_CC_CTRL 0xb8 #define AXP20X_FG_RES 0xb9 +/* AXP288 specific registers */ +#define AXP288_PMIC_ADC_H 0x56 +#define AXP288_PMIC_ADC_L 0x57 +#define AXP288_ADC_TS_PIN_CTRL 0x84 + +#define AXP288_PMIC_ADC_EN 0x84 +#define AXP288_FG_TUNE5 0xed + + /* Regulators IDs */ enum { AXP20X_LDO1 = 0, @@ -169,12 +182,58 @@ enum { AXP20X_IRQ_GPIO0_INPUT, }; +enum axp288_irqs { + AXP288_IRQ_VBUS_FALL = 2, + AXP288_IRQ_VBUS_RISE, + AXP288_IRQ_OV, + AXP288_IRQ_FALLING_ALT, + AXP288_IRQ_RISING_ALT, + AXP288_IRQ_OV_ALT, + AXP288_IRQ_DONE = 10, + AXP288_IRQ_CHARGING, + AXP288_IRQ_SAFE_QUIT, + AXP288_IRQ_SAFE_ENTER, + AXP288_IRQ_ABSENT, + AXP288_IRQ_APPEND, + AXP288_IRQ_QWBTU, + AXP288_IRQ_WBTU, + AXP288_IRQ_QWBTO, + AXP288_IRQ_WBTO, + AXP288_IRQ_QCBTU, + AXP288_IRQ_CBTU, + AXP288_IRQ_QCBTO, + AXP288_IRQ_CBTO, + AXP288_IRQ_WL2, + AXP288_IRQ_WL1, + AXP288_IRQ_GPADC, + AXP288_IRQ_OT = 31, + AXP288_IRQ_GPIO0, + AXP288_IRQ_GPIO1, + AXP288_IRQ_POKO, + AXP288_IRQ_POKL, + AXP288_IRQ_POKS, + AXP288_IRQ_POKN, + AXP288_IRQ_POKP, + AXP288_IRQ_TIMER, + AXP288_IRQ_MV_CHNG, + AXP288_IRQ_BC_USB_CHNG, +}; + +#define AXP288_TS_ADC_H 0x58 +#define AXP288_TS_ADC_L 0x59 +#define AXP288_GP_ADC_H 0x5a +#define AXP288_GP_ADC_L 0x5b + struct axp20x_dev { struct device *dev; struct i2c_client *i2c_client; struct regmap *regmap; struct regmap_irq_chip_data *regmap_irqc; long variant; + int nr_cells; + struct mfd_cell *cells; + const struct regmap_config *regmap_cfg; + const struct regmap_irq_chip *regmap_irq_chip; }; #endif /* __LINUX_MFD_AXP20X_H */ diff --git a/include/linux/mfd/core.h b/include/linux/mfd/core.h index 73e1709d4c09..a76bc100bf97 100644 --- a/include/linux/mfd/core.h +++ b/include/linux/mfd/core.h @@ -111,6 +111,13 @@ extern int mfd_add_devices(struct device *parent, int id, struct resource *mem_base, int irq_base, struct irq_domain *irq_domain); +static inline int mfd_add_hotplug_devices(struct device *parent, + const struct mfd_cell *cells, int n_devs) +{ + return mfd_add_devices(parent, PLATFORM_DEVID_AUTO, cells, n_devs, + NULL, 0, NULL); +} + extern void mfd_remove_devices(struct device *parent); #endif diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h new file mode 100644 index 000000000000..004b24576da8 --- /dev/null +++ b/include/linux/mfd/dln2.h @@ -0,0 +1,103 @@ +#ifndef __LINUX_USB_DLN2_H +#define __LINUX_USB_DLN2_H + +#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8)) + +struct dln2_platform_data { + u16 handle; /* sub-driver handle (internally used only) */ + u8 port; /* I2C/SPI port */ +}; + +/** + * dln2_event_cb_t - event callback function signature + * + * @pdev - the sub-device that registered this callback + * @echo - the echo header field received in the message + * @data - the data payload + * @len - the data payload length + * + * The callback function is called in interrupt context and the data payload is + * only valid during the call. If the user needs later access of the data, it + * must copy it. + */ + +typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo, + const void *data, int len); + +/** + * dl2n_register_event_cb - register a callback function for an event + * + * @pdev - the sub-device that registers the callback + * @event - the event for which to register a callback + * @event_cb - the callback function + * + * @return 0 in case of success, negative value in case of error + */ +int dln2_register_event_cb(struct platform_device *pdev, u16 event, + dln2_event_cb_t event_cb); + +/** + * dln2_unregister_event_cb - unregister the callback function for an event + * + * @pdev - the sub-device that registered the callback + * @event - the event for which to register a callback + */ +void dln2_unregister_event_cb(struct platform_device *pdev, u16 event); + +/** + * dln2_transfer - issue a DLN2 command and wait for a response and the + * associated data + * + * @pdev - the sub-device which is issuing this transfer + * @cmd - the command to be sent to the device + * @obuf - the buffer to be sent to the device; it can be NULL if the user + * doesn't need to transmit data with this command + * @obuf_len - the size of the buffer to be sent to the device + * @ibuf - any data associated with the response will be copied here; it can be + * NULL if the user doesn't need the response data + * @ibuf_len - must be initialized to the input buffer size; it will be modified + * to indicate the actual data transferred; + * + * @return 0 for success, negative value for errors + */ +int dln2_transfer(struct platform_device *pdev, u16 cmd, + const void *obuf, unsigned obuf_len, + void *ibuf, unsigned *ibuf_len); + +/** + * dln2_transfer_rx - variant of @dln2_transfer() where TX buffer is not needed + * + * @pdev - the sub-device which is issuing this transfer + * @cmd - the command to be sent to the device + * @ibuf - any data associated with the response will be copied here; it can be + * NULL if the user doesn't need the response data + * @ibuf_len - must be initialized to the input buffer size; it will be modified + * to indicate the actual data transferred; + * + * @return 0 for success, negative value for errors + */ + +static inline int dln2_transfer_rx(struct platform_device *pdev, u16 cmd, + void *ibuf, unsigned *ibuf_len) +{ + return dln2_transfer(pdev, cmd, NULL, 0, ibuf, ibuf_len); +} + +/** + * dln2_transfer_tx - variant of @dln2_transfer() where RX buffer is not needed + * + * @pdev - the sub-device which is issuing this transfer + * @cmd - the command to be sent to the device + * @obuf - the buffer to be sent to the device; it can be NULL if the + * user doesn't need to transmit data with this command + * @obuf_len - the size of the buffer to be sent to the device + * + * @return 0 for success, negative value for errors + */ +static inline int dln2_transfer_tx(struct platform_device *pdev, u16 cmd, + const void *obuf, unsigned obuf_len) +{ + return dln2_transfer(pdev, cmd, obuf, obuf_len, NULL, NULL); +} + +#endif diff --git a/include/linux/mfd/max77693-private.h b/include/linux/mfd/max77693-private.h index 582e67f34054..08dae01258b9 100644 --- a/include/linux/mfd/max77693-private.h +++ b/include/linux/mfd/max77693-private.h @@ -26,7 +26,6 @@ #include <linux/i2c.h> -#define MAX77693_NUM_IRQ_MUIC_REGS 3 #define MAX77693_REG_INVALID (0xff) /* Slave addr = 0xCC: PMIC, Charger, Flash LED */ diff --git a/include/linux/mfd/rtsx_pci.h b/include/linux/mfd/rtsx_pci.h index 74346d5e7899..0c12628e91c6 100644 --- a/include/linux/mfd/rtsx_pci.h +++ b/include/linux/mfd/rtsx_pci.h @@ -558,6 +558,7 @@ #define SD_SAMPLE_POINT_CTL 0xFDA7 #define SD_PUSH_POINT_CTL 0xFDA8 #define SD_CMD0 0xFDA9 +#define SD_CMD_START 0x40 #define SD_CMD1 0xFDAA #define SD_CMD2 0xFDAB #define SD_CMD3 0xFDAC @@ -707,6 +708,14 @@ #define PM_CTRL1 0xFF44 #define PM_CTRL2 0xFF45 #define PM_CTRL3 0xFF46 +#define SDIO_SEND_PME_EN 0x80 +#define FORCE_RC_MODE_ON 0x40 +#define FORCE_RX50_LINK_ON 0x20 +#define D3_DELINK_MODE_EN 0x10 +#define USE_PESRTB_CTL_DELINK 0x08 +#define DELAY_PIN_WAKE 0x04 +#define RESET_PIN_WAKE 0x02 +#define PM_WAKE_EN 0x01 #define PM_CTRL4 0xFF47 /* Memory mapping */ @@ -752,6 +761,14 @@ #define PHY_DUM_REG 0x1F #define LCTLR 0x80 +#define LCTLR_EXT_SYNC 0x80 +#define LCTLR_COMMON_CLOCK_CFG 0x40 +#define LCTLR_RETRAIN_LINK 0x20 +#define LCTLR_LINK_DISABLE 0x10 +#define LCTLR_RCB 0x08 +#define LCTLR_RESERVED 0x04 +#define LCTLR_ASPM_CTL_MASK 0x03 + #define PCR_SETTING_REG1 0x724 #define PCR_SETTING_REG2 0x814 #define PCR_SETTING_REG3 0x747 @@ -967,4 +984,24 @@ static inline u8 *rtsx_pci_get_cmd_data(struct rtsx_pcr *pcr) return (u8 *)(pcr->host_cmds_ptr); } +static inline int rtsx_pci_update_cfg_byte(struct rtsx_pcr *pcr, int addr, + u8 mask, u8 append) +{ + int err; + u8 val; + + err = pci_read_config_byte(pcr->pci, addr, &val); + if (err < 0) + return err; + return pci_write_config_byte(pcr->pci, addr, (val & mask) | append); +} + +static inline void rtsx_pci_write_be32(struct rtsx_pcr *pcr, u16 reg, u32 val) +{ + rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg, 0xFF, val >> 24); + rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 1, 0xFF, val >> 16); + rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 2, 0xFF, val >> 8); + rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 3, 0xFF, val); +} + #endif diff --git a/include/linux/mfd/samsung/core.h b/include/linux/mfd/samsung/core.h index 1825edacbda7..3fdb7cfbffb3 100644 --- a/include/linux/mfd/samsung/core.h +++ b/include/linux/mfd/samsung/core.h @@ -28,6 +28,7 @@ #define MIN_800_MV 800000 #define MIN_750_MV 750000 #define MIN_600_MV 600000 +#define MIN_500_MV 500000 /* Macros to represent steps for LDO/BUCK */ #define STEP_50_MV 50000 @@ -41,6 +42,7 @@ enum sec_device_type { S5M8767X, S2MPA01, S2MPS11X, + S2MPS13X, S2MPS14X, S2MPU02, }; diff --git a/include/linux/mfd/samsung/s2mps13.h b/include/linux/mfd/samsung/s2mps13.h new file mode 100644 index 000000000000..ce5dda8958fe --- /dev/null +++ b/include/linux/mfd/samsung/s2mps13.h @@ -0,0 +1,186 @@ +/* + * s2mps13.h + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __LINUX_MFD_S2MPS13_H +#define __LINUX_MFD_S2MPS13_H + +/* S2MPS13 registers */ +enum s2mps13_reg { + S2MPS13_REG_ID, + S2MPS13_REG_INT1, + S2MPS13_REG_INT2, + S2MPS13_REG_INT3, + S2MPS13_REG_INT1M, + S2MPS13_REG_INT2M, + S2MPS13_REG_INT3M, + S2MPS13_REG_ST1, + S2MPS13_REG_ST2, + S2MPS13_REG_PWRONSRC, + S2MPS13_REG_OFFSRC, + S2MPS13_REG_BU_CHG, + S2MPS13_REG_RTCCTRL, + S2MPS13_REG_CTRL1, + S2MPS13_REG_CTRL2, + S2MPS13_REG_RSVD1, + S2MPS13_REG_RSVD2, + S2MPS13_REG_RSVD3, + S2MPS13_REG_RSVD4, + S2MPS13_REG_RSVD5, + S2MPS13_REG_RSVD6, + S2MPS13_REG_CTRL3, + S2MPS13_REG_RSVD7, + S2MPS13_REG_RSVD8, + S2MPS13_REG_WRSTBI, + S2MPS13_REG_B1CTRL, + S2MPS13_REG_B1OUT, + S2MPS13_REG_B2CTRL, + S2MPS13_REG_B2OUT, + S2MPS13_REG_B3CTRL, + S2MPS13_REG_B3OUT, + S2MPS13_REG_B4CTRL, + S2MPS13_REG_B4OUT, + S2MPS13_REG_B5CTRL, + S2MPS13_REG_B5OUT, + S2MPS13_REG_B6CTRL, + S2MPS13_REG_B6OUT, + S2MPS13_REG_B7CTRL, + S2MPS13_REG_B7OUT, + S2MPS13_REG_B8CTRL, + S2MPS13_REG_B8OUT, + S2MPS13_REG_B9CTRL, + S2MPS13_REG_B9OUT, + S2MPS13_REG_B10CTRL, + S2MPS13_REG_B10OUT, + S2MPS13_REG_BB1CTRL, + S2MPS13_REG_BB1OUT, + S2MPS13_REG_BUCK_RAMP1, + S2MPS13_REG_BUCK_RAMP2, + S2MPS13_REG_LDO_DVS1, + S2MPS13_REG_LDO_DVS2, + S2MPS13_REG_LDO_DVS3, + S2MPS13_REG_B6OUT2, + S2MPS13_REG_L1CTRL, + S2MPS13_REG_L2CTRL, + S2MPS13_REG_L3CTRL, + S2MPS13_REG_L4CTRL, + S2MPS13_REG_L5CTRL, + S2MPS13_REG_L6CTRL, + S2MPS13_REG_L7CTRL, + S2MPS13_REG_L8CTRL, + S2MPS13_REG_L9CTRL, + S2MPS13_REG_L10CTRL, + S2MPS13_REG_L11CTRL, + S2MPS13_REG_L12CTRL, + S2MPS13_REG_L13CTRL, + S2MPS13_REG_L14CTRL, + S2MPS13_REG_L15CTRL, + S2MPS13_REG_L16CTRL, + S2MPS13_REG_L17CTRL, + S2MPS13_REG_L18CTRL, + S2MPS13_REG_L19CTRL, + S2MPS13_REG_L20CTRL, + S2MPS13_REG_L21CTRL, + S2MPS13_REG_L22CTRL, + S2MPS13_REG_L23CTRL, + S2MPS13_REG_L24CTRL, + S2MPS13_REG_L25CTRL, + S2MPS13_REG_L26CTRL, + S2MPS13_REG_L27CTRL, + S2MPS13_REG_L28CTRL, + S2MPS13_REG_L30CTRL, + S2MPS13_REG_L31CTRL, + S2MPS13_REG_L32CTRL, + S2MPS13_REG_L33CTRL, + S2MPS13_REG_L34CTRL, + S2MPS13_REG_L35CTRL, + S2MPS13_REG_L36CTRL, + S2MPS13_REG_L37CTRL, + S2MPS13_REG_L38CTRL, + S2MPS13_REG_L39CTRL, + S2MPS13_REG_L40CTRL, + S2MPS13_REG_LDODSCH1, + S2MPS13_REG_LDODSCH2, + S2MPS13_REG_LDODSCH3, + S2MPS13_REG_LDODSCH4, + S2MPS13_REG_LDODSCH5, +}; + +/* regulator ids */ +enum s2mps13_regulators { + S2MPS13_LDO1, + S2MPS13_LDO2, + S2MPS13_LDO3, + S2MPS13_LDO4, + S2MPS13_LDO5, + S2MPS13_LDO6, + S2MPS13_LDO7, + S2MPS13_LDO8, + S2MPS13_LDO9, + S2MPS13_LDO10, + S2MPS13_LDO11, + S2MPS13_LDO12, + S2MPS13_LDO13, + S2MPS13_LDO14, + S2MPS13_LDO15, + S2MPS13_LDO16, + S2MPS13_LDO17, + S2MPS13_LDO18, + S2MPS13_LDO19, + S2MPS13_LDO20, + S2MPS13_LDO21, + S2MPS13_LDO22, + S2MPS13_LDO23, + S2MPS13_LDO24, + S2MPS13_LDO25, + S2MPS13_LDO26, + S2MPS13_LDO27, + S2MPS13_LDO28, + S2MPS13_LDO29, + S2MPS13_LDO30, + S2MPS13_LDO31, + S2MPS13_LDO32, + S2MPS13_LDO33, + S2MPS13_LDO34, + S2MPS13_LDO35, + S2MPS13_LDO36, + S2MPS13_LDO37, + S2MPS13_LDO38, + S2MPS13_LDO39, + S2MPS13_LDO40, + S2MPS13_BUCK1, + S2MPS13_BUCK2, + S2MPS13_BUCK3, + S2MPS13_BUCK4, + S2MPS13_BUCK5, + S2MPS13_BUCK6, + S2MPS13_BUCK7, + S2MPS13_BUCK8, + S2MPS13_BUCK9, + S2MPS13_BUCK10, + + S2MPS13_REGULATOR_MAX, +}; + +/* + * Default ramp delay in uv/us. Datasheet says that ramp delay can be + * controlled however it does not specify which register is used for that. + * Let's assume that default value will be set. + */ +#define S2MPS13_BUCK_RAMP_DELAY 12500 + +#endif /* __LINUX_MFD_S2MPS13_H */ diff --git a/include/linux/mfd/tc3589x.h b/include/linux/mfd/tc3589x.h index e6088c2e2092..e1c12d84c26a 100644 --- a/include/linux/mfd/tc3589x.h +++ b/include/linux/mfd/tc3589x.h @@ -164,13 +164,10 @@ struct tc3589x_keypad_platform_data { /** * struct tc3589x_gpio_platform_data - TC3589x GPIO platform data - * @gpio_base: first gpio number assigned to TC3589x. A maximum of - * %TC3589x_NR_GPIOS GPIOs will be allocated. * @setup: callback for board-specific initialization * @remove: callback for board-specific teardown */ struct tc3589x_gpio_platform_data { - int gpio_base; void (*setup)(struct tc3589x *tc3589x, unsigned gpio_base); void (*remove)(struct tc3589x *tc3589x, unsigned gpio_base); }; @@ -178,18 +175,13 @@ struct tc3589x_gpio_platform_data { /** * struct tc3589x_platform_data - TC3589x platform data * @block: bitmask of blocks to enable (use TC3589x_BLOCK_*) - * @irq_base: base IRQ number. %TC3589x_NR_IRQS irqs will be used. * @gpio: GPIO-specific platform data * @keypad: keypad-specific platform data */ struct tc3589x_platform_data { unsigned int block; - int irq_base; struct tc3589x_gpio_platform_data *gpio; const struct tc3589x_keypad_platform_data *keypad; }; -#define TC3589x_NR_GPIOS 24 -#define TC3589x_NR_IRQS TC3589x_INT_GPIO(TC3589x_NR_GPIOS) - #endif diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index b0692d28f8e6..4d69c00497bd 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -88,6 +88,9 @@ struct mmc_ext_csd { unsigned int data_tag_unit_size; /* DATA TAG UNIT size */ unsigned int boot_ro_lock; /* ro lock support */ bool boot_ro_lockable; + bool ffu_capable; /* Firmware upgrade support */ +#define MMC_FIRMWARE_LEN 8 + u8 fwrev[MMC_FIRMWARE_LEN]; /* FW version */ u8 raw_exception_status; /* 54 */ u8 raw_partition_support; /* 160 */ u8 raw_rpmb_size_mult; /* 168 */ @@ -509,24 +512,8 @@ static inline int mmc_card_broken_irq_polling(const struct mmc_card *c) #define mmc_dev_to_card(d) container_of(d, struct mmc_card, dev) -#define mmc_list_to_card(l) container_of(l, struct mmc_card, node) -#define mmc_get_drvdata(c) dev_get_drvdata(&(c)->dev) -#define mmc_set_drvdata(c,d) dev_set_drvdata(&(c)->dev, d) - -/* - * MMC device driver (e.g., Flash card, I/O card...) - */ -struct mmc_driver { - struct device_driver drv; - int (*probe)(struct mmc_card *); - void (*remove)(struct mmc_card *); - int (*suspend)(struct mmc_card *); - int (*resume)(struct mmc_card *); - void (*shutdown)(struct mmc_card *); -}; - -extern int mmc_register_driver(struct mmc_driver *); -extern void mmc_unregister_driver(struct mmc_driver *); +extern int mmc_register_driver(struct device_driver *); +extern void mmc_unregister_driver(struct device_driver *); extern void mmc_fixup_device(struct mmc_card *card, const struct mmc_fixup *table); diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h index f206e29f94d7..cb2b0400d284 100644 --- a/include/linux/mmc/core.h +++ b/include/linux/mmc/core.h @@ -154,7 +154,8 @@ extern void mmc_start_bkops(struct mmc_card *card, bool from_exception); extern int __mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int, bool, bool, bool); extern int mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int); -extern int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd); +extern int mmc_send_tuning(struct mmc_host *host); +extern int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd); #define MMC_ERASE_ARG 0x00000000 #define MMC_SECURE_ERASE_ARG 0x80000000 diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h index 001366927cf4..42b724e8d503 100644 --- a/include/linux/mmc/dw_mmc.h +++ b/include/linux/mmc/dw_mmc.h @@ -54,6 +54,7 @@ struct mmc_data; * transfer is in progress. * @use_dma: Whether DMA channel is initialized or not. * @using_dma: Whether DMA is in use for the current transfer. + * @dma_64bit_address: Whether DMA supports 64-bit address mode or not. * @sg_dma: Bus address of DMA buffer. * @sg_cpu: Virtual address of DMA buffer. * @dma_ops: Pointer to platform-specific DMA callbacks. @@ -96,6 +97,7 @@ struct mmc_data; * @quirks: Set of quirks that apply to specific versions of the IP. * @irq_flags: The flags to be passed to request_irq. * @irq: The irq value to be passed to request_irq. + * @sdio_id0: Number of slot0 in the SDIO interrupt registers. * * Locking * ======= @@ -135,11 +137,11 @@ struct dw_mci { struct mmc_command stop_abort; unsigned int prev_blksz; unsigned char timing; - struct workqueue_struct *card_workqueue; /* DMA interface members*/ int use_dma; int using_dma; + int dma_64bit_address; dma_addr_t sg_dma; void *sg_cpu; @@ -154,7 +156,6 @@ struct dw_mci { u32 stop_cmdr; u32 dir_status; struct tasklet_struct tasklet; - struct work_struct card_work; unsigned long pending_events; unsigned long completed_events; enum dw_mci_state state; @@ -193,6 +194,8 @@ struct dw_mci { bool vqmmc_enabled; unsigned long irq_flags; /* IRQ flags */ int irq; + + int sdio_id0; }; /* DMA ops for Internal/External DMAC interface */ diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index df0c15396bbf..9f322706f7cb 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -289,6 +289,7 @@ struct mmc_host { #define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */ #define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \ MMC_CAP2_HS400_1_2V) +#define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V) #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17) mmc_pm_flag_t pm_caps; /* supported pm features */ diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h index 1cd00b3a75b9..49ad7a943638 100644 --- a/include/linux/mmc/mmc.h +++ b/include/linux/mmc/mmc.h @@ -296,6 +296,7 @@ struct _mmc_csd { #define EXT_CSD_SANITIZE_START 165 /* W */ #define EXT_CSD_WR_REL_PARAM 166 /* RO */ #define EXT_CSD_RPMB_MULT 168 /* RO */ +#define EXT_CSD_FW_CONFIG 169 /* R/W */ #define EXT_CSD_BOOT_WP 173 /* R/W */ #define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */ #define EXT_CSD_PART_CONFIG 179 /* R/W */ @@ -332,6 +333,8 @@ struct _mmc_csd { #define EXT_CSD_GENERIC_CMD6_TIME 248 /* RO */ #define EXT_CSD_CACHE_SIZE 249 /* RO, 4 bytes */ #define EXT_CSD_PWR_CL_DDR_200_360 253 /* RO */ +#define EXT_CSD_FIRMWARE_VERSION 254 /* RO, 8 bytes */ +#define EXT_CSD_SUPPORTED_MODE 493 /* RO */ #define EXT_CSD_TAG_UNIT_SIZE 498 /* RO */ #define EXT_CSD_DATA_TAG_SUPPORT 499 /* RO */ #define EXT_CSD_MAX_PACKED_WRITES 500 /* RO */ diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h index dba793e3a331..375af80bde7d 100644 --- a/include/linux/mmc/sdhci.h +++ b/include/linux/mmc/sdhci.h @@ -100,6 +100,12 @@ struct sdhci_host { #define SDHCI_QUIRK2_BROKEN_DDR50 (1<<7) /* Stop command (CMD12) can set Transfer Complete when not using MMC_RSP_BUSY */ #define SDHCI_QUIRK2_STOP_WITH_TC (1<<8) +/* Controller does not support 64-bit DMA */ +#define SDHCI_QUIRK2_BROKEN_64_BIT_DMA (1<<9) +/* need clear transfer mode register before send cmd */ +#define SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD (1<<10) +/* Capability register bit-63 indicates HS400 support */ +#define SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 (1<<11) int irq; /* Device IRQ */ void __iomem *ioaddr; /* Mapped address */ @@ -130,6 +136,7 @@ struct sdhci_host { #define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */ #define SDHCI_SDR104_NEEDS_TUNING (1<<10) /* SDR104/HS200 needs tuning */ #define SDHCI_USING_RETUNING_TIMER (1<<11) /* Host is using a retuning timer for the card */ +#define SDHCI_USE_64_BIT_DMA (1<<12) /* Use 64-bit DMA */ unsigned int version; /* SDHCI spec. version */ @@ -155,12 +162,19 @@ struct sdhci_host { int sg_count; /* Mapped sg entries */ - u8 *adma_desc; /* ADMA descriptor table */ - u8 *align_buffer; /* Bounce buffer */ + void *adma_table; /* ADMA descriptor table */ + void *align_buffer; /* Bounce buffer */ + + size_t adma_table_sz; /* ADMA descriptor table size */ + size_t align_buffer_sz; /* Bounce buffer size */ dma_addr_t adma_addr; /* Mapped ADMA descr. table */ dma_addr_t align_addr; /* Mapped bounce buffer */ + unsigned int desc_sz; /* ADMA descriptor size */ + unsigned int align_sz; /* ADMA alignment */ + unsigned int align_mask; /* ADMA alignment mask */ + struct tasklet_struct finish_tasklet; /* Tasklet structures */ struct timer_list timer; /* Timer for timeouts */ diff --git a/include/linux/mmc/sdio_func.h b/include/linux/mmc/sdio_func.h index 50f0bc952328..aab032a6ae61 100644 --- a/include/linux/mmc/sdio_func.h +++ b/include/linux/mmc/sdio_func.h @@ -84,8 +84,6 @@ struct sdio_driver { struct device_driver drv; }; -#define to_sdio_driver(d) container_of(d, struct sdio_driver, drv) - /** * SDIO_DEVICE - macro used to describe a specific SDIO device * @vend: the 16 bit manufacturer code diff --git a/include/linux/of.h b/include/linux/of.h index 29f0adc5f3e4..364a15858746 100644 --- a/include/linux/of.h +++ b/include/linux/of.h @@ -922,4 +922,15 @@ static inline int of_changeset_update_property(struct of_changeset *ocs, /* CONFIG_OF_RESOLVE api */ extern int of_resolve_phandles(struct device_node *tree); +/** + * of_system_has_poweroff_source - Tells if poweroff-source is found for device_node + * @np: Pointer to the given device_node + * + * return true if present false otherwise + */ +static inline bool of_system_has_poweroff_source(const struct device_node *np) +{ + return of_property_read_bool(np, "poweroff-source"); +} + #endif /* _LINUX_OF_H */ diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 1fa99a301817..97fb9f69aaed 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -522,6 +522,8 @@ #define PCI_DEVICE_ID_AMD_15H_M10H_F3 0x1403 #define PCI_DEVICE_ID_AMD_15H_M30H_NB_F3 0x141d #define PCI_DEVICE_ID_AMD_15H_M30H_NB_F4 0x141e +#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F3 0x1573 +#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F4 0x1574 #define PCI_DEVICE_ID_AMD_15H_NB_F0 0x1600 #define PCI_DEVICE_ID_AMD_15H_NB_F1 0x1601 #define PCI_DEVICE_ID_AMD_15H_NB_F2 0x1602 diff --git a/include/linux/platform_data/hsmmc-omap.h b/include/linux/platform_data/hsmmc-omap.h new file mode 100644 index 000000000000..67bbcf0785f6 --- /dev/null +++ b/include/linux/platform_data/hsmmc-omap.h @@ -0,0 +1,90 @@ +/* + * MMC definitions for OMAP2 + * + * Copyright (C) 2006 Nokia Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * struct omap_hsmmc_dev_attr.flags possibilities + * + * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can + * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag + * should be set if this is the case. See for example Section 22.5.3 + * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia + * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R). + * + * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers + * don't work correctly on some MMC controller instances on some + * OMAP3 SoCs; this flag should be set if this is the case. See + * for example Advisory 2.1.1.128 "MMC: Multiple Block Read + * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_ + * Revision F (October 2010) (SPRZ278F). + */ +#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0) +#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1) +#define OMAP_HSMMC_SWAKEUP_MISSING BIT(2) + +struct omap_hsmmc_dev_attr { + u8 flags; +}; + +struct mmc_card; + +struct omap_hsmmc_platform_data { + /* back-link to device */ + struct device *dev; + + /* set if your board has components or wiring that limits the + * maximum frequency on the MMC bus */ + unsigned int max_freq; + + /* Integrating attributes from the omap_hwmod layer */ + u8 controller_flags; + + /* Register offset deviation */ + u16 reg_offset; + + /* + * 4/8 wires and any additional host capabilities + * need to OR'd all capabilities (ref. linux/mmc/host.h) + */ + u32 caps; /* Used for the MMC driver on 2430 and later */ + u32 pm_caps; /* PM capabilities of the mmc */ + + /* switch pin can be for card detect (default) or card cover */ + unsigned cover:1; + + /* use the internal clock */ + unsigned internal_clock:1; + + /* nonremovable e.g. eMMC */ + unsigned nonremovable:1; + + /* eMMC does not handle power off when not in sleep state */ + unsigned no_regulator_off_init:1; + + /* we can put the features above into this variable */ +#define HSMMC_HAS_PBIAS (1 << 0) +#define HSMMC_HAS_UPDATED_RESET (1 << 1) +#define HSMMC_HAS_HSPE_SUPPORT (1 << 2) + unsigned features; + + int switch_pin; /* gpio (card detect) */ + int gpio_wp; /* gpio (write protect) */ + + int (*set_power)(struct device *dev, int power_on, int vdd); + void (*remux)(struct device *dev, int power_on); + /* Call back before enabling / disabling regulators */ + void (*before_set_reg)(struct device *dev, int power_on, int vdd); + /* Call back after enabling / disabling regulators */ + void (*after_set_reg)(struct device *dev, int power_on, int vdd); + /* if we have special card, init it using this callback */ + void (*init_card)(struct mmc_card *card); + + const char *name; + u32 ocr_mask; +}; diff --git a/include/linux/platform_data/mmc-atmel-mci.h b/include/linux/platform_data/mmc-atmel-mci.h new file mode 100644 index 000000000000..399a2d5a14bd --- /dev/null +++ b/include/linux/platform_data/mmc-atmel-mci.h @@ -0,0 +1,22 @@ +#ifndef __MMC_ATMEL_MCI_H +#define __MMC_ATMEL_MCI_H + +#include <linux/platform_data/dma-atmel.h> +#include <linux/platform_data/dma-dw.h> + +/** + * struct mci_dma_data - DMA data for MCI interface + */ +struct mci_dma_data { +#ifdef CONFIG_ARM + struct at_dma_slave sdata; +#else + struct dw_dma_slave sdata; +#endif +}; + +/* accessor macros */ +#define slave_data_ptr(s) (&(s)->sdata) +#define find_slave_dev(s) ((s)->sdata.dma_dev) + +#endif /* __MMC_ATMEL_MCI_H */ diff --git a/include/linux/platform_data/mmc-omap.h b/include/linux/platform_data/mmc-omap.h index 51e70cf25cbc..5c188f4e9bec 100644 --- a/include/linux/platform_data/mmc-omap.h +++ b/include/linux/platform_data/mmc-omap.h @@ -10,32 +10,8 @@ #define OMAP_MMC_MAX_SLOTS 2 -/* - * struct omap_mmc_dev_attr.flags possibilities - * - * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can - * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag - * should be set if this is the case. See for example Section 22.5.3 - * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia - * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R). - * - * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers - * don't work correctly on some MMC controller instances on some - * OMAP3 SoCs; this flag should be set if this is the case. See - * for example Advisory 2.1.1.128 "MMC: Multiple Block Read - * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_ - * Revision F (October 2010) (SPRZ278F). - */ -#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0) -#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1) -#define OMAP_HSMMC_SWAKEUP_MISSING BIT(2) - struct mmc_card; -struct omap_mmc_dev_attr { - u8 flags; -}; - struct omap_mmc_platform_data { /* back-link to device */ struct device *dev; @@ -106,9 +82,6 @@ struct omap_mmc_platform_data { unsigned vcc_aux_disable_is_sleep:1; /* we can put the features above into this variable */ -#define HSMMC_HAS_PBIAS (1 << 0) -#define HSMMC_HAS_UPDATED_RESET (1 << 1) -#define HSMMC_HAS_HSPE_SUPPORT (1 << 2) #define MMC_OMAP7XX (1 << 3) #define MMC_OMAP15XX (1 << 4) #define MMC_OMAP16XX (1 << 5) diff --git a/include/linux/platform_data/pxa_sdhci.h b/include/linux/platform_data/pxa_sdhci.h index 27d3156d093a..9e20c2fb4ffd 100644 --- a/include/linux/platform_data/pxa_sdhci.h +++ b/include/linux/platform_data/pxa_sdhci.h @@ -55,9 +55,4 @@ struct sdhci_pxa_platdata { unsigned int quirks2; unsigned int pm_caps; }; - -struct sdhci_pxa { - u8 clk_enable; - u8 power_mode; -}; #endif /* _PXA_SDHCI_H_ */ |
