diff options
Diffstat (limited to 'include/linux/ssb')
| -rw-r--r-- | include/linux/ssb/ssb.h | 424 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_driver_chipcommon.h | 396 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_driver_extif.h | 204 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_driver_mips.h | 46 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_driver_pci.h | 106 | ||||
| -rw-r--r-- | include/linux/ssb/ssb_regs.h | 292 |
6 files changed, 1468 insertions, 0 deletions
diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h new file mode 100644 index 000000000000..2b5c312c4960 --- /dev/null +++ b/include/linux/ssb/ssb.h @@ -0,0 +1,424 @@ +#ifndef LINUX_SSB_H_ +#define LINUX_SSB_H_ + +#include <linux/device.h> +#include <linux/list.h> +#include <linux/types.h> +#include <linux/spinlock.h> +#include <linux/pci.h> +#include <linux/mod_devicetable.h> + +#include <linux/ssb/ssb_regs.h> + + +struct pcmcia_device; +struct ssb_bus; +struct ssb_driver; + + +struct ssb_sprom_r1 { + u16 pci_spid; /* Subsystem Product ID for PCI */ + u16 pci_svid; /* Subsystem Vendor ID for PCI */ + u16 pci_pid; /* Product ID for PCI */ + u8 il0mac[6]; /* MAC address for 802.11b/g */ + u8 et0mac[6]; /* MAC address for Ethernet */ + u8 et1mac[6]; /* MAC address for 802.11a */ + u8 et0phyaddr:5; /* MII address for enet0 */ + u8 et1phyaddr:5; /* MII address for enet1 */ + u8 et0mdcport:1; /* MDIO for enet0 */ + u8 et1mdcport:1; /* MDIO for enet1 */ + u8 board_rev; /* Board revision */ + u8 country_code:4; /* Country Code */ + u8 antenna_a:2; /* Antenna 0/1 available for A-PHY */ + u8 antenna_bg:2; /* Antenna 0/1 available for B-PHY and G-PHY */ + u16 pa0b0; + u16 pa0b1; + u16 pa0b2; + u16 pa1b0; + u16 pa1b1; + u16 pa1b2; + u8 gpio0; /* GPIO pin 0 */ + u8 gpio1; /* GPIO pin 1 */ + u8 gpio2; /* GPIO pin 2 */ + u8 gpio3; /* GPIO pin 3 */ + u16 maxpwr_a; /* A-PHY Power Amplifier Max Power (in dBm Q5.2) */ + u16 maxpwr_bg; /* B/G-PHY Power Amplifier Max Power (in dBm Q5.2) */ + u8 itssi_a; /* Idle TSSI Target for A-PHY */ + u8 itssi_bg; /* Idle TSSI Target for B/G-PHY */ + u16 boardflags_lo; /* Boardflags (low 16 bits) */ + u8 antenna_gain_a; /* A-PHY Antenna gain (in dBm Q5.2) */ + u8 antenna_gain_bg; /* B/G-PHY Antenna gain (in dBm Q5.2) */ + u8 oem[8]; /* OEM string (rev 1 only) */ +}; + +struct ssb_sprom_r2 { + u16 boardflags_hi; /* Boardflags (high 16 bits) */ + u8 maxpwr_a_lo; /* A-PHY Max Power Low */ + u8 maxpwr_a_hi; /* A-PHY Max Power High */ + u16 pa1lob0; /* A-PHY PA Low Settings */ + u16 pa1lob1; /* A-PHY PA Low Settings */ + u16 pa1lob2; /* A-PHY PA Low Settings */ + u16 pa1hib0; /* A-PHY PA High Settings */ + u16 pa1hib1; /* A-PHY PA High Settings */ + u16 pa1hib2; /* A-PHY PA High Settings */ + u8 ofdm_pwr_off; /* OFDM Power Offset from CCK Level */ + u8 country_str[2]; /* Two char Country Code */ +}; + +struct ssb_sprom_r3 { + u32 ofdmapo; /* A-PHY OFDM Mid Power Offset */ + u32 ofdmalpo; /* A-PHY OFDM Low Power Offset */ + u32 ofdmahpo; /* A-PHY OFDM High Power Offset */ + u8 gpioldc_on_cnt; /* GPIO LED Powersave Duty Cycle ON count */ + u8 gpioldc_off_cnt; /* GPIO LED Powersave Duty Cycle OFF count */ + u8 cckpo_1M:4; /* CCK Power Offset for Rate 1M */ + u8 cckpo_2M:4; /* CCK Power Offset for Rate 2M */ + u8 cckpo_55M:4; /* CCK Power Offset for Rate 5.5M */ + u8 cckpo_11M:4; /* CCK Power Offset for Rate 11M */ + u32 ofdmgpo; /* G-PHY OFDM Power Offset */ +}; + +struct ssb_sprom_r4 { + /* TODO */ +}; + +struct ssb_sprom { + u8 revision; + u8 crc; + /* The valid r# fields are selected by the "revision". + * Revision 3 and lower inherit from lower revisions. + */ + union { + struct { + struct ssb_sprom_r1 r1; + struct ssb_sprom_r2 r2; + struct ssb_sprom_r3 r3; + }; + struct ssb_sprom_r4 r4; + }; +}; + +/* Information about the PCB the circuitry is soldered on. */ +struct ssb_boardinfo { + u16 vendor; + u16 type; + u16 rev; +}; + + +struct ssb_device; +/* Lowlevel read/write operations on the device MMIO. + * Internal, don't use that outside of ssb. */ +struct ssb_bus_ops { + u16 (*read16)(struct ssb_device *dev, u16 offset); + u32 (*read32)(struct ssb_device *dev, u16 offset); + void (*write16)(struct ssb_device *dev, u16 offset, u16 value); + void (*write32)(struct ssb_device *dev, u16 offset, u32 value); +}; + + +/* Core-ID values. */ +#define SSB_DEV_CHIPCOMMON 0x800 +#define SSB_DEV_ILINE20 0x801 +#define SSB_DEV_SDRAM 0x803 +#define SSB_DEV_PCI 0x804 +#define SSB_DEV_MIPS 0x805 +#define SSB_DEV_ETHERNET 0x806 +#define SSB_DEV_V90 0x807 +#define SSB_DEV_USB11_HOSTDEV 0x808 +#define SSB_DEV_ADSL 0x809 +#define SSB_DEV_ILINE100 0x80A +#define SSB_DEV_IPSEC 0x80B +#define SSB_DEV_PCMCIA 0x80D +#define SSB_DEV_INTERNAL_MEM 0x80E +#define SSB_DEV_MEMC_SDRAM 0x80F +#define SSB_DEV_EXTIF 0x811 +#define SSB_DEV_80211 0x812 +#define SSB_DEV_MIPS_3302 0x816 +#define SSB_DEV_USB11_HOST 0x817 +#define SSB_DEV_USB11_DEV 0x818 +#define SSB_DEV_USB20_HOST 0x819 +#define SSB_DEV_USB20_DEV 0x81A +#define SSB_DEV_SDIO_HOST 0x81B +#define SSB_DEV_ROBOSWITCH 0x81C +#define SSB_DEV_PARA_ATA 0x81D +#define SSB_DEV_SATA_XORDMA 0x81E +#define SSB_DEV_ETHERNET_GBIT 0x81F +#define SSB_DEV_PCIE 0x820 +#define SSB_DEV_MIMO_PHY 0x821 +#define SSB_DEV_SRAM_CTRLR 0x822 +#define SSB_DEV_MINI_MACPHY 0x823 +#define SSB_DEV_ARM_1176 0x824 +#define SSB_DEV_ARM_7TDMI 0x825 + +/* Vendor-ID values */ +#define SSB_VENDOR_BROADCOM 0x4243 + +/* Some kernel subsystems poke with dev->drvdata, so we must use the + * following ugly workaround to get from struct device to struct ssb_device */ +struct __ssb_dev_wrapper { + struct device dev; + struct ssb_device *sdev; +}; + +struct ssb_device { + /* Having a copy of the ops pointer in each dev struct + * is an optimization. */ + const struct ssb_bus_ops *ops; + + struct device *dev; + struct ssb_bus *bus; + struct ssb_device_id id; + + u8 core_index; + unsigned int irq; + + /* Internal-only stuff follows. */ + void *drvdata; /* Per-device data */ + void *devtypedata; /* Per-devicetype (eg 802.11) data */ +}; + +/* Go from struct device to struct ssb_device. */ +static inline +struct ssb_device * dev_to_ssb_dev(struct device *dev) +{ + struct __ssb_dev_wrapper *wrap; + wrap = container_of(dev, struct __ssb_dev_wrapper, dev); + return wrap->sdev; +} + +/* Device specific user data */ +static inline +void ssb_set_drvdata(struct ssb_device *dev, void *data) +{ + dev->drvdata = data; +} +static inline +void * ssb_get_drvdata(struct ssb_device *dev) +{ + return dev->drvdata; +} + +/* Devicetype specific user data. This is per device-type (not per device) */ +void ssb_set_devtypedata(struct ssb_device *dev, void *data); +static inline +void * ssb_get_devtypedata(struct ssb_device *dev) +{ + return dev->devtypedata; +} + + +struct ssb_driver { + const char *name; + const struct ssb_device_id *id_table; + + int (*probe)(struct ssb_device *dev, const struct ssb_device_id *id); + void (*remove)(struct ssb_device *dev); + int (*suspend)(struct ssb_device *dev, pm_message_t state); + int (*resume)(struct ssb_device *dev); + void (*shutdown)(struct ssb_device *dev); + + struct device_driver drv; +}; +#define drv_to_ssb_drv(_drv) container_of(_drv, struct ssb_driver, drv) + +extern int __ssb_driver_register(struct ssb_driver *drv, struct module *owner); +static inline int ssb_driver_register(struct ssb_driver *drv) +{ + return __ssb_driver_register(drv, THIS_MODULE); +} +extern void ssb_driver_unregister(struct ssb_driver *drv); + + + + +enum ssb_bustype { + SSB_BUSTYPE_SSB, /* This SSB bus is the system bus */ + SSB_BUSTYPE_PCI, /* SSB is connected to PCI bus */ + SSB_BUSTYPE_PCMCIA, /* SSB is connected to PCMCIA bus */ +}; + +/* board_vendor */ +#define SSB_BOARDVENDOR_BCM 0x14E4 /* Broadcom */ +#define SSB_BOARDVENDOR_DELL 0x1028 /* Dell */ +#define SSB_BOARDVENDOR_HP 0x0E11 /* HP */ +/* board_type */ +#define SSB_BOARD_BCM94306MP 0x0418 +#define SSB_BOARD_BCM4309G 0x0421 +#define SSB_BOARD_BCM4306CB 0x0417 +#define SSB_BOARD_BCM4309MP 0x040C +#define SSB_BOARD_MP4318 0x044A +#define SSB_BOARD_BU4306 0x0416 +#define SSB_BOARD_BU4309 0x040A +/* chip_package */ +#define SSB_CHIPPACK_BCM4712S 1 /* Small 200pin 4712 */ +#define SSB_CHIPPACK_BCM4712M 2 /* Medium 225pin 4712 */ +#define SSB_CHIPPACK_BCM4712L 0 /* Large 340pin 4712 */ + +#include <linux/ssb/ssb_driver_chipcommon.h> +#include <linux/ssb/ssb_driver_mips.h> +#include <linux/ssb/ssb_driver_extif.h> +#include <linux/ssb/ssb_driver_pci.h> + +struct ssb_bus { + /* The MMIO area. */ + void __iomem *mmio; + + const struct ssb_bus_ops *ops; + + /* The core in the basic address register window. (PCI bus only) */ + struct ssb_device *mapped_device; + /* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */ + u8 mapped_pcmcia_seg; + /* Lock for core and segment switching. */ + spinlock_t bar_lock; + + /* The bus this backplane is running on. */ + enum ssb_bustype bustype; + /* Pointer to the PCI bus (only valid if bustype == SSB_BUSTYPE_PCI). */ + struct pci_dev *host_pci; + /* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */ + struct pcmcia_device *host_pcmcia; + +#ifdef CONFIG_SSB_PCIHOST + /* Mutex to protect the SPROM writing. */ + struct mutex pci_sprom_mutex; +#endif + + /* ID information about the Chip. */ + u16 chip_id; + u16 chip_rev; + u8 chip_package; + + /* List of devices (cores) on the backplane. */ + struct ssb_device devices[SSB_MAX_NR_CORES]; + u8 nr_devices; + + /* Reference count. Number of suspended devices. */ + u8 suspend_cnt; + + /* Software ID number for this bus. */ + unsigned int busnumber; + + /* The ChipCommon device (if available). */ + struct ssb_chipcommon chipco; + /* The PCI-core device (if available). */ + struct ssb_pcicore pcicore; + /* The MIPS-core device (if available). */ + struct ssb_mipscore mipscore; + /* The EXTif-core device (if available). */ + struct ssb_extif extif; + + /* The following structure elements are not available in early + * SSB initialization. Though, they are available for regular + * registered drivers at any stage. So be careful when + * using them in the ssb core code. */ + + /* ID information about the PCB. */ + struct ssb_boardinfo boardinfo; + /* Contents of the SPROM. */ + struct ssb_sprom sprom; + + /* Internal-only stuff follows. Do not touch. */ + struct list_head list; +#ifdef CONFIG_SSB_DEBUG + /* Is the bus already powered up? */ + bool powered_up; + int power_warn_count; +#endif /* DEBUG */ +}; + +/* The initialization-invariants. */ +struct ssb_init_invariants { + struct ssb_boardinfo boardinfo; + struct ssb_sprom sprom; +}; +/* Type of function to fetch the invariants. */ +typedef int (*ssb_invariants_func_t)(struct ssb_bus *bus, + struct ssb_init_invariants *iv); + +/* Register a SSB system bus. get_invariants() is called after the + * basic system devices are initialized. + * The invariants are usually fetched from some NVRAM. + * Put the invariants into the struct pointed to by iv. */ +extern int ssb_bus_ssbbus_register(struct ssb_bus *bus, + unsigned long baseaddr, + ssb_invariants_func_t get_invariants); +#ifdef CONFIG_SSB_PCIHOST +extern int ssb_bus_pcibus_register(struct ssb_bus *bus, + struct pci_dev *host_pci); +#endif /* CONFIG_SSB_PCIHOST */ +#ifdef CONFIG_SSB_PCMCIAHOST +extern int ssb_bus_pcmciabus_register(struct ssb_bus *bus, + struct pcmcia_device *pcmcia_dev, + unsigned long baseaddr); +#endif /* CONFIG_SSB_PCMCIAHOST */ + +extern void ssb_bus_unregister(struct ssb_bus *bus); + +extern u32 ssb_clockspeed(struct ssb_bus *bus); + +/* Is the device enabled in hardware? */ +int ssb_device_is_enabled(struct ssb_device *dev); +/* Enable a device and pass device-specific SSB_TMSLOW flags. + * If no device-specific flags are available, use 0. */ +void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags); +/* Disable a device in hardware and pass SSB_TMSLOW flags (if any). */ +void ssb_device_disable(struct ssb_device *dev, u32 core_specific_flags); + + +/* Device MMIO register read/write functions. */ +static inline u16 ssb_read16(struct ssb_device *dev, u16 offset) +{ + return dev->ops->read16(dev, offset); +} +static inline u32 ssb_read32(struct ssb_device *dev, u16 offset) +{ + return dev->ops->read32(dev, offset); +} +static inline void ssb_write16(struct ssb_device *dev, u16 offset, u16 value) +{ + dev->ops->write16(dev, offset, value); +} +static inline void ssb_write32(struct ssb_device *dev, u16 offset, u32 value) +{ + dev->ops->write32(dev, offset, value); +} + + +/* Translation (routing) bits that need to be ORed to DMA + * addresses before they are given to a device. */ +extern u32 ssb_dma_translation(struct ssb_device *dev); +#define SSB_DMA_TRANSLATION_MASK 0xC0000000 +#define SSB_DMA_TRANSLATION_SHIFT 30 + +extern int ssb_dma_set_mask(struct ssb_device *ssb_dev, u64 mask); + + +#ifdef CONFIG_SSB_PCIHOST +/* PCI-host wrapper driver */ +extern int ssb_pcihost_register(struct pci_driver *driver); +static inline void ssb_pcihost_unregister(struct pci_driver *driver) +{ + pci_unregister_driver(driver); +} +#endif /* CONFIG_SSB_PCIHOST */ + + +/* If a driver is shutdown or suspended, call this to signal + * that the bus may be completely powered down. SSB will decide, + * if it's really time to power down the bus, based on if there + * are other devices that want to run. */ +extern int ssb_bus_may_powerdown(struct ssb_bus *bus); +/* Before initializing and enabling a device, call this to power-up the bus. + * If you want to allow use of dynamic-power-control, pass the flag. + * Otherwise static always-on powercontrol will be used. */ +extern int ssb_bus_powerup(struct ssb_bus *bus, bool dynamic_pctl); + + +/* Various helper functions */ +extern u32 ssb_admatch_base(u32 adm); +extern u32 ssb_admatch_size(u32 adm); + + +#endif /* LINUX_SSB_H_ */ diff --git a/include/linux/ssb/ssb_driver_chipcommon.h b/include/linux/ssb/ssb_driver_chipcommon.h new file mode 100644 index 000000000000..4cb995494662 --- /dev/null +++ b/include/linux/ssb/ssb_driver_chipcommon.h @@ -0,0 +1,396 @@ +#ifndef LINUX_SSB_CHIPCO_H_ +#define LINUX_SSB_CHIPCO_H_ + +/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions + * + * The chipcommon core provides chip identification, SB control, + * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer, + * gpio interface, extbus, and support for serial and parallel flashes. + * + * Copyright 2005, Broadcom Corporation + * Copyright 2006, Michael Buesch <mb@bu3sch.de> + * + * Licensed under the GPL version 2. See COPYING for details. + */ + +/** ChipCommon core registers. **/ + +#define SSB_CHIPCO_CHIPID 0x0000 +#define SSB_CHIPCO_IDMASK 0x0000FFFF +#define SSB_CHIPCO_REVMASK 0x000F0000 +#define SSB_CHIPCO_REVSHIFT 16 +#define SSB_CHIPCO_PACKMASK 0x00F00000 +#define SSB_CHIPCO_PACKSHIFT 20 +#define SSB_CHIPCO_NRCORESMASK 0x0F000000 +#define SSB_CHIPCO_NRCORESSHIFT 24 +#define SSB_CHIPCO_CAP 0x0004 /* Capabilities */ +#define SSB_CHIPCO_CAP_NRUART 0x00000003 /* # of UARTs */ +#define SSB_CHIPCO_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */ +#define SSB_CHIPCO_CAP_UARTCLK 0x00000018 /* UART clock select */ +#define SSB_CHIPCO_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */ +#define SSB_CHIPCO_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */ +#define SSB_CHIPCO_CAP_EXTBUS 0x000000C0 /* External buses present */ +#define SSB_CHIPCO_CAP_FLASHT 0x00000700 /* Flash Type */ +#define SSB_CHIPCO_FLASHT_NONE 0x00000000 /* No flash */ +#define SSB_CHIPCO_FLASHT_STSER 0x00000100 /* ST serial flash */ +#define SSB_CHIPCO_FLASHT_ATSER 0x00000200 /* Atmel serial flash */ +#define SSB_CHIPCO_FLASHT_PARA 0x00000700 /* Parallel flash */ +#define SSB_CHIPCO_CAP_PLLT 0x00038000 /* PLL Type */ +#define SSB_PLLTYPE_NONE 0x00000000 +#define SSB_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */ +#define SSB_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */ +#define SSB_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */ +#define SSB_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */ +#define SSB_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */ +#define SSB_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */ +#define SSB_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */ +#define SSB_CHIPCO_CAP_PCTL 0x00040000 /* Power Control */ +#define SSB_CHIPCO_CAP_OTPS 0x00380000 /* OTP size */ +#define SSB_CHIPCO_CAP_OTPS_SHIFT 19 +#define SSB_CHIPCO_CAP_OTPS_BASE 5 +#define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */ +#define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */ +#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */ +#define SSB_CHIPCO_CORECTL 0x0008 +#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ +#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ +#define SSB_CHIPCO_BIST 0x000C +#define SSB_CHIPCO_OTPS 0x0010 /* OTP status */ +#define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000 +#define SSB_CHIPCO_OTPS_PROTECT 0x00000007 +#define SSB_CHIPCO_OTPS_HW_PROTECT 0x00000001 +#define SSB_CHIPCO_OTPS_SW_PROTECT 0x00000002 +#define SSB_CHIPCO_OTPS_CID_PROTECT 0x00000004 +#define SSB_CHIPCO_OTPC 0x0014 /* OTP control */ +#define SSB_CHIPCO_OTPC_RECWAIT 0xFF000000 +#define SSB_CHIPCO_OTPC_PROGWAIT 0x00FFFF00 +#define SSB_CHIPCO_OTPC_PRW_SHIFT 8 +#define SSB_CHIPCO_OTPC_MAXFAIL 0x00000038 +#define SSB_CHIPCO_OTPC_VSEL 0x00000006 +#define SSB_CHIPCO_OTPC_SELVL 0x00000001 +#define SSB_CHIPCO_OTPP 0x0018 /* OTP prog */ +#define SSB_CHIPCO_OTPP_COL 0x000000FF +#define SSB_CHIPCO_OTPP_ROW 0x0000FF00 +#define SSB_CHIPCO_OTPP_ROW_SHIFT 8 +#define SSB_CHIPCO_OTPP_READERR 0x10000000 +#define SSB_CHIPCO_OTPP_VALUE 0x20000000 +#define SSB_CHIPCO_OTPP_READ 0x40000000 +#define SSB_CHIPCO_OTPP_START 0x80000000 +#define SSB_CHIPCO_OTPP_BUSY 0x80000000 +#define SSB_CHIPCO_IRQSTAT 0x0020 +#define SSB_CHIPCO_IRQMASK 0x0024 +#define SSB_CHIPCO_IRQ_GPIO 0x00000001 /* gpio intr */ +#define SSB_CHIPCO_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */ +#define SSB_CHIPCO_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */ +#define SSB_CHIPCO_CHIPCTL 0x0028 /* Rev >= 11 only */ +#define SSB_CHIPCO_CHIPSTAT 0x002C /* Rev >= 11 only */ +#define SSB_CHIPCO_JCMD 0x0030 /* Rev >= 10 only */ +#define SSB_CHIPCO_JCMD_START 0x80000000 +#define SSB_CHIPCO_JCMD_BUSY 0x80000000 +#define SSB_CHIPCO_JCMD_PAUSE 0x40000000 +#define SSB_CHIPCO_JCMD0_ACC_MASK 0x0000F000 +#define SSB_CHIPCO_JCMD0_ACC_IRDR 0x00000000 +#define SSB_CHIPCO_JCMD0_ACC_DR 0x00001000 +#define SSB_CHIPCO_JCMD0_ACC_IR 0x00002000 +#define SSB_CHIPCO_JCMD0_ACC_RESET 0x00003000 +#define SSB_CHIPCO_JCMD0_ACC_IRPDR 0x00004000 +#define SSB_CHIPCO_JCMD0_ACC_PDR 0x00005000 +#define SSB_CHIPCO_JCMD0_IRW_MASK 0x00000F00 +#define SSB_CHIPCO_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */ +#define SSB_CHIPCO_JCMD_ACC_IRDR 0x00000000 +#define SSB_CHIPCO_JCMD_ACC_DR 0x00010000 +#define SSB_CHIPCO_JCMD_ACC_IR 0x00020000 +#define SSB_CHIPCO_JCMD_ACC_RESET 0x00030000 +#define SSB_CHIPCO_JCMD_ACC_IRPDR 0x00040000 +#define SSB_CHIPCO_JCMD_ACC_PDR 0x00050000 +#define SSB_CHIPCO_JCMD_IRW_MASK 0x00001F00 +#define SSB_CHIPCO_JCMD_IRW_SHIFT 8 +#define SSB_CHIPCO_JCMD_DRW_MASK 0x0000003F +#define SSB_CHIPCO_JIR 0x0034 /* Rev >= 10 only */ +#define SSB_CHIPCO_JDR 0x0038 /* Rev >= 10 only */ +#define SSB_CHIPCO_JCTL 0x003C /* Rev >= 10 only */ +#define SSB_CHIPCO_JCTL_FORCE_CLK 4 /* Force clock */ +#define SSB_CHIPCO_JCTL_EXT_EN 2 /* Enable external targets */ +#define SSB_CHIPCO_JCTL_EN 1 /* Enable Jtag master */ +#define SSB_CHIPCO_FLASHCTL 0x0040 +#define SSB_CHIPCO_FLASHCTL_START 0x80000000 +#define SSB_CHIPCO_FLASHCTL_BUSY SSB_CHIPCO_FLASHCTL_START +#define SSB_CHIPCO_FLASHADDR 0x0044 +#define SSB_CHIPCO_FLASHDATA 0x0048 +#define SSB_CHIPCO_BCAST_ADDR 0x0050 +#define SSB_CHIPCO_BCAST_DATA 0x0054 +#define SSB_CHIPCO_GPIOIN 0x0060 +#define SSB_CHIPCO_GPIOOUT 0x0064 +#define SSB_CHIPCO_GPIOOUTEN 0x0068 +#define SSB_CHIPCO_GPIOCTL 0x006C +#define SSB_CHIPCO_GPIOPOL 0x0070 +#define SSB_CHIPCO_GPIOIRQ 0x0074 +#define SSB_CHIPCO_WATCHDOG 0x0080 +#define SSB_CHIPCO_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */ +#define SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT 16 +#define SSB_CHIPCO_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */ +#define SSB_CHIPCO_CLOCK_N 0x0090 +#define SSB_CHIPCO_CLOCK_SB 0x0094 +#define SSB_CHIPCO_CLOCK_PCI 0x0098 +#define SSB_CHIPCO_CLOCK_M2 0x009C +#define SSB_CHIPCO_CLOCK_MIPS 0x00A0 +#define SSB_CHIPCO_CLKDIV 0x00A4 /* Rev >= 3 only */ +#define SSB_CHIPCO_CLKDIV_SFLASH 0x0F000000 +#define SSB_CHIPCO_CLKDIV_SFLASH_SHIFT 24 +#define SSB_CHIPCO_CLKDIV_OTP 0x000F0000 +#define SSB_CHIPCO_CLKDIV_OTP_SHIFT 16 +#define SSB_CHIPCO_CLKDIV_JTAG 0x00000F00 +#define SSB_CHIPCO_CLKDIV_JTAG_SHIFT 8 +#define SSB_CHIPCO_CLKDIV_UART 0x000000FF +#define SSB_CHIPCO_PLLONDELAY 0x00B0 /* Rev >= 4 only */ +#define SSB_CHIPCO_FREFSELDELAY 0x00B4 /* Rev >= 4 only */ +#define SSB_CHIPCO_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */ +#define SSB_CHIPCO_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */ +#define SSB_CHIPCO_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */ +#define SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */ +#define SSB_CHIPCO_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */ +#define SSB_CHIPCO_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ +#define SSB_CHIPCO_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */ +#define SSB_CHIPCO_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */ +#define SSB_CHIPCO_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */ +#define SSB_CHIPCO_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */ +#define SSB_CHIPCO_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ +#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ +#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT 16 +#define SSB_CHIPCO_SYSCLKCTL 0x00C0 /* Rev >= 3 only */ +#define SSB_CHIPCO_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */ +#define SSB_CHIPCO_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */ +#define SSB_CHIPCO_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */ +#define SSB_CHIPCO_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */ +#define SSB_CHIPCO_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */ +#define SSB_CHIPCO_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */ +#define SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT 16 +#define SSB_CHIPCO_CLKSTSTR 0x00C4 /* Rev >= 3 only */ +#define SSB_CHIPCO_PCMCIA_CFG 0x0100 +#define SSB_CHIPCO_PCMCIA_MEMWAIT 0x0104 +#define SSB_CHIPCO_PCMCIA_ATTRWAIT 0x0108 +#define SSB_CHIPCO_PCMCIA_IOWAIT 0x010C +#define SSB_CHIPCO_IDE_CFG 0x0110 +#define SSB_CHIPCO_IDE_MEMWAIT 0x0114 +#define SSB_CHIPCO_IDE_ATTRWAIT 0x0118 +#define SSB_CHIPCO_IDE_IOWAIT 0x011C +#define SSB_CHIPCO_PROG_CFG 0x0120 +#define SSB_CHIPCO_PROG_WAITCNT 0x0124 +#define SSB_CHIPCO_FLASH_CFG 0x0128 +#define SSB_CHIPCO_FLASH_WAITCNT 0x012C +#define SSB_CHIPCO_UART0_DATA 0x0300 +#define SSB_CHIPCO_UART0_IMR 0x0304 +#define SSB_CHIPCO_UART0_FCR 0x0308 +#define SSB_CHIPCO_UART0_LCR 0x030C +#define SSB_CHIPCO_UART0_MCR 0x0310 +#define SSB_CHIPCO_UART0_LSR 0x0314 +#define SSB_CHIPCO_UART0_MSR 0x0318 +#define SSB_CHIPCO_UART0_SCRATCH 0x031C +#define SSB_CHIPCO_UART1_DATA 0x0400 +#define SSB_CHIPCO_UART1_IMR 0x0404 +#define SSB_CHIPCO_UART1_FCR 0x0408 +#define SSB_CHIPCO_UART1_LCR 0x040C +#define SSB_CHIPCO_UART1_MCR 0x0410 +#define SSB_CHIPCO_UART1_LSR 0x0414 +#define SSB_CHIPCO_UART1_MSR 0x0418 +#define SSB_CHIPCO_UART1_SCRATCH 0x041C + + + +/** Clockcontrol masks and values **/ + +/* SSB_CHIPCO_CLOCK_N */ +#define SSB_CHIPCO_CLK_N1 0x0000003F /* n1 control */ +#define SSB_CHIPCO_CLK_N2 0x00003F00 /* n2 control */ +#define SSB_CHIPCO_CLK_N2_SHIFT 8 +#define SSB_CHIPCO_CLK_PLLC 0x000F0000 /* pll control */ +#define SSB_CHIPCO_CLK_PLLC_SHIFT 16 + +/* SSB_CHIPCO_CLOCK_SB/PCI/UART */ +#define SSB_CHIPCO_CLK_M1 0x0000003F /* m1 control */ +#define SSB_CHIPCO_CLK_M2 0x00003F00 /* m2 control */ +#define SSB_CHIPCO_CLK_M2_SHIFT 8 +#define SSB_CHIPCO_CLK_M3 0x003F0000 /* m3 control */ +#define SSB_CHIPCO_CLK_M3_SHIFT 16 +#define SSB_CHIPCO_CLK_MC 0x1F000000 /* mux control */ +#define SSB_CHIPCO_CLK_MC_SHIFT 24 + +/* N3M Clock control magic field values */ +#define SSB_CHIPCO_CLK_F6_2 0x02 /* A factor of 2 in */ +#define SSB_CHIPCO_CLK_F6_3 0x03 /* 6-bit fields like */ +#define SSB_CHIPCO_CLK_F6_4 0x05 /* N1, M1 or M3 */ +#define SSB_CHIPCO_CLK_F6_5 0x09 +#define SSB_CHIPCO_CLK_F6_6 0x11 +#define SSB_CHIPCO_CLK_F6_7 0x21 + +#define SSB_CHIPCO_CLK_F5_BIAS 5 /* 5-bit fields get this added */ + +#define SSB_CHIPCO_CLK_MC_BYPASS 0x08 +#define SSB_CHIPCO_CLK_MC_M1 0x04 +#define SSB_CHIPCO_CLK_MC_M1M2 0x02 +#define SSB_CHIPCO_CLK_MC_M1M2M3 0x01 +#define SSB_CHIPCO_CLK_MC_M1M3 0x11 + +/* Type 2 Clock control magic field values */ +#define SSB_CHIPCO_CLK_T2_BIAS 2 /* n1, n2, m1 & m3 bias */ +#define SSB_CHIPCO_CLK_T2M2_BIAS 3 /* m2 bias */ + +#define SSB_CHIPCO_CLK_T2MC_M1BYP 1 +#define SSB_CHIPCO_CLK_T2MC_M2BYP 2 +#define SSB_CHIPCO_CLK_T2MC_M3BYP 4 + +/* Type 6 Clock control magic field values */ +#define SSB_CHIPCO_CLK_T6_MMASK 1 /* bits of interest in m */ +#define SSB_CHIPCO_CLK_T6_M0 120000000 /* sb clock for m = 0 */ +#define SSB_CHIPCO_CLK_T6_M1 100000000 /* sb clock for m = 1 */ +#define SSB_CHIPCO_CLK_SB2MIPS_T6(sb) (2 * (sb)) + +/* Common clock base */ +#define SSB_CHIPCO_CLK_BASE1 24000000 /* Half the clock freq */ +#define SSB_CHIPCO_CLK_BASE2 12500000 /* Alternate crystal on some PLL's */ + +/* Clock control values for 200Mhz in 5350 */ +#define SSB_CHIPCO_CLK_5350_N 0x0311 +#define SSB_CHIPCO_CLK_5350_M 0x04020009 + + +/** Bits in the config registers **/ + +#define SSB_CHIPCO_CFG_EN 0x0001 /* Enable */ +#define SSB_CHIPCO_CFG_EXTM 0x000E /* Extif Mode */ +#define SSB_CHIPCO_CFG_EXTM_ASYNC 0x0002 /* Async/Parallel flash */ +#define SSB_CHIPCO_CFG_EXTM_SYNC 0x0004 /* Synchronous */ +#define SSB_CHIPCO_CFG_EXTM_PCMCIA 0x0008 /* PCMCIA */ +#define SSB_CHIPCO_CFG_EXTM_IDE 0x000A /* IDE */ +#define SSB_CHIPCO_CFG_DS16 0x0010 /* Data size, 0=8bit, 1=16bit */ +#define SSB_CHIPCO_CFG_CLKDIV 0x0060 /* Sync: Clock divisor */ +#define SSB_CHIPCO_CFG_CLKEN 0x0080 /* Sync: Clock enable */ +#define SSB_CHIPCO_CFG_BSTRO 0x0100 /* Sync: Size/Bytestrobe */ + + +/** Flash-specific control/status values */ + +/* flashcontrol opcodes for ST flashes */ +#define SSB_CHIPCO_FLASHCTL_ST_WREN 0x0006 /* Write Enable */ +#define SSB_CHIPCO_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */ +#define SSB_CHIPCO_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */ +#define SSB_CHIPCO_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */ +#define SSB_CHIPCO_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */ +#define SSB_CHIPCO_FLASHCTL_ST_PP 0x0302 /* Page Program */ +#define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */ +#define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */ +#define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */ +#define SSB_CHIPCO_FLASHCTL_ST_RSIG 0x03AB /* Read Electronic Signature */ + +/* Status register bits for ST flashes */ +#define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */ +#define SSB_CHIPCO_FLASHSTA_ST_WEL 0x02 /* Write Enable Latch */ +#define SSB_CHIPCO_FLASHSTA_ST_BP 0x1C /* Block Protect */ +#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT 2 +#define SSB_CHIPCO_FLASHSTA_ST_SRWD 0x80 /* Status Register Write Disable */ + +/* flashcontrol opcodes for Atmel flashes */ +#define SSB_CHIPCO_FLASHCTL_AT_READ 0x07E8 +#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ 0x07D2 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ /* FIXME */ +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ /* FIXME */ +#define SSB_CHIPCO_FLASHCTL_AT_STATUS 0x01D7 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE 0x0384 +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE 0x0387 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM 0x0283 /* Erase program */ +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM 0x0286 /* Erase program */ +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM 0x0288 +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM 0x0289 +#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE 0x0281 +#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE 0x0250 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM 0x0382 /* Write erase program */ +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM 0x0385 /* Write erase program */ +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD 0x0253 +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD 0x0255 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE 0x0260 +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE 0x0261 +#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM 0x0258 +#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM 0x0259 + +/* Status register bits for Atmel flashes */ +#define SSB_CHIPCO_FLASHSTA_AT_READY 0x80 +#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH 0x40 +#define SSB_CHIPCO_FLASHSTA_AT_ID 0x38 +#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT 3 + + +/** OTP **/ + +/* OTP regions */ +#define SSB_CHIPCO_OTP_HW_REGION SSB_CHIPCO_OTPS_HW_PROTECT +#define SSB_CHIPCO_OTP_SW_REGION SSB_CHIPCO_OTPS_SW_PROTECT +#define SSB_CHIPCO_OTP_CID_REGION SSB_CHIPCO_OTPS_CID_PROTECT + +/* OTP regions (Byte offsets from otp size) */ +#define SSB_CHIPCO_OTP_SWLIM_OFF (-8) +#define SSB_CHIPCO_OTP_CIDBASE_OFF 0 +#define SSB_CHIPCO_OTP_CIDLIM_OFF 8 + +/* Predefined OTP words (Word offset from otp size) */ +#define SSB_CHIPCO_OTP_BOUNDARY_OFF (-4) +#define SSB_CHIPCO_OTP_HWSIGN_OFF (-3) +#define SSB_CHIPCO_OTP_SWSIGN_OFF (-2) +#define SSB_CHIPCO_OTP_CIDSIGN_OFF (-1) + +#define SSB_CHIPCO_OTP_CID_OFF 0 +#define SSB_CHIPCO_OTP_PKG_OFF 1 +#define SSB_CHIPCO_OTP_FID_OFF 2 +#define SSB_CHIPCO_OTP_RSV_OFF 3 +#define SSB_CHIPCO_OTP_LIM_OFF 4 + +#define SSB_CHIPCO_OTP_SIGNATURE 0x578A +#define SSB_CHIPCO_OTP_MAGIC 0x4E56 + + +struct ssb_device; +struct ssb_serial_port; + +struct ssb_chipcommon { + struct ssb_device *dev; + u32 capabilities; + /* Fast Powerup Delay constant */ + u16 fast_pwrup_delay; +}; + +extern void ssb_chipcommon_init(struct ssb_chipcommon *cc); + +#include <linux/pm.h> +extern void ssb_chipco_suspend(struct ssb_chipcommon *cc, pm_message_t state); +extern void ssb_chipco_resume(struct ssb_chipcommon *cc); + +extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc, + u32 *plltype, u32 *n, u32 *m); +extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc, + u32 *plltype, u32 *n, u32 *m); +extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc, + unsigned long ns_per_cycle); + +enum ssb_clkmode { + SSB_CLKMODE_SLOW, + SSB_CLKMODE_FAST, + SSB_CLKMODE_DYNAMIC, +}; + +extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc, + enum ssb_clkmode mode); + +extern void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, + u32 ticks); + +u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask); + +void ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value); + +void ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value); + +#ifdef CONFIG_SSB_SERIAL +extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc, + struct ssb_serial_port *ports); +#endif /* CONFIG_SSB_SERIAL */ + +#endif /* LINUX_SSB_CHIPCO_H_ */ diff --git a/include/linux/ssb/ssb_driver_extif.h b/include/linux/ssb/ssb_driver_extif.h new file mode 100644 index 000000000000..a9164357b5ae --- /dev/null +++ b/include/linux/ssb/ssb_driver_extif.h @@ -0,0 +1,204 @@ +/* + * Hardware-specific External Interface I/O core definitions + * for the BCM47xx family of SiliconBackplane-based chips. + * + * The External Interface core supports a total of three external chip selects + * supporting external interfaces. One of the external chip selects is + * used for Flash, one is used for PCMCIA, and the other may be + * programmed to support either a synchronous interface or an + * asynchronous interface. The asynchronous interface can be used to + * support external devices such as UARTs and the BCM2019 Bluetooth + * baseband processor. + * The external interface core also contains 2 on-chip 16550 UARTs, clock + * frequency control, a watchdog interrupt timer, and a GPIO interface. + * + * Copyright 2005, Broadcom Corporation + * Copyright 2006, Michael Buesch + * + * Licensed under the GPL version 2. See COPYING for details. + */ +#ifndef LINUX_SSB_EXTIFCORE_H_ +#define LINUX_SSB_EXTIFCORE_H_ + +/* external interface address space */ +#define SSB_EXTIF_PCMCIA_MEMBASE(x) (x) +#define SSB_EXTIF_PCMCIA_IOBASE(x) ((x) + 0x100000) +#define SSB_EXTIF_PCMCIA_CFGBASE(x) ((x) + 0x200000) +#define SSB_EXTIF_CFGIF_BASE(x) ((x) + 0x800000) +#define SSB_EXTIF_FLASH_BASE(x) ((x) + 0xc00000) + +#define SSB_EXTIF_NR_GPIOOUT 5 +/* GPIO NOTE: + * The multiple instances of output and output enable registers + * are present to allow driver software for multiple cores to control + * gpio outputs without needing to share a single register pair. + * Use the following helper macro to get a register offset value. + */ +#define SSB_EXTIF_GPIO_OUT(index) ({ \ + BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT); \ + SSB_EXTIF_GPIO_OUT_BASE + ((index) * 8); \ + }) +#define SSB_EXTIF_GPIO_OUTEN(index) ({ \ + BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT); \ + SSB_EXTIF_GPIO_OUTEN_BASE + ((index) * 8); \ + }) + +/** EXTIF core registers **/ + +#define SSB_EXTIF_CTL 0x0000 +#define SSB_EXTIF_CTL_UARTEN (1 << 0) /* UART enable */ +#define SSB_EXTIF_EXTSTAT 0x0004 +#define SSB_EXTIF_EXTSTAT_EMODE (1 << 0) /* Endian mode (ro) */ +#define SSB_EXTIF_EXTSTAT_EIRQPIN (1 << 1) /* External interrupt pin (ro) */ +#define SSB_EXTIF_EXTSTAT_GPIOIRQPIN (1 << 2) /* GPIO interrupt pin (ro) */ +#define SSB_EXTIF_PCMCIA_CFG 0x0010 +#define SSB_EXTIF_PCMCIA_MEMWAIT 0x0014 +#define SSB_EXTIF_PCMCIA_ATTRWAIT 0x0018 +#define SSB_EXTIF_PCMCIA_IOWAIT 0x001C +#define SSB_EXTIF_PROG_CFG 0x0020 +#define SSB_EXTIF_PROG_WAITCNT 0x0024 +#define SSB_EXTIF_FLASH_CFG 0x0028 +#define SSB_EXTIF_FLASH_WAITCNT 0x002C +#define SSB_EXTIF_WATCHDOG 0x0040 +#define SSB_EXTIF_CLOCK_N 0x0044 +#define SSB_EXTIF_CLOCK_SB 0x0048 +#define SSB_EXTIF_CLOCK_PCI 0x004C +#define SSB_EXTIF_CLOCK_MII 0x0050 +#define SSB_EXTIF_GPIO_IN 0x0060 +#define SSB_EXTIF_GPIO_OUT_BASE 0x0064 +#define SSB_EXTIF_GPIO_OUTEN_BASE 0x0068 +#define SSB_EXTIF_EJTAG_OUTEN 0x0090 +#define SSB_EXTIF_GPIO_INTPOL 0x0094 +#define SSB_EXTIF_GPIO_INTMASK 0x0098 +#define SSB_EXTIF_UART_DATA 0x0300 +#define SSB_EXTIF_UART_TIMER 0x0310 +#define SSB_EXTIF_UART_FCR 0x0320 +#define SSB_EXTIF_UART_LCR 0x0330 +#define SSB_EXTIF_UART_MCR 0x0340 +#define SSB_EXTIF_UART_LSR 0x0350 +#define SSB_EXTIF_UART_MSR 0x0360 +#define SSB_EXTIF_UART_SCRATCH 0x0370 + + + + +/* pcmcia/prog/flash_config */ +#define SSB_EXTCFG_EN (1 << 0) /* enable */ +#define SSB_EXTCFG_MODE 0xE /* mode */ +#define SSB_EXTCFG_MODE_SHIFT 1 +#define SSB_EXTCFG_MODE_FLASH 0x0 /* flash/asynchronous mode */ +#define SSB_EXTCFG_MODE_SYNC 0x2 /* synchronous mode */ +#define SSB_EXTCFG_MODE_PCMCIA 0x4 /* pcmcia mode */ +#define SSB_EXTCFG_DS16 (1 << 4) /* destsize: 0=8bit, 1=16bit */ +#define SSB_EXTCFG_BSWAP (1 << 5) /* byteswap */ +#define SSB_EXTCFG_CLKDIV 0xC0 /* clock divider */ +#define SSB_EXTCFG_CLKDIV_SHIFT 6 +#define SSB_EXTCFG_CLKDIV_2 0x0 /* backplane/2 */ +#define SSB_EXTCFG_CLKDIV_3 0x40 /* backplane/3 */ +#define SSB_EXTCFG_CLKDIV_4 0x80 /* backplane/4 */ +#define SSB_EXTCFG_CLKEN (1 << 8) /* clock enable */ +#define SSB_EXTCFG_STROBE (1 << 9) /* size/bytestrobe (synch only) */ + +/* pcmcia_memwait */ +#define SSB_PCMCIA_MEMW_0 0x0000003F /* waitcount0 */ +#define SSB_PCMCIA_MEMW_1 0x00001F00 /* waitcount1 */ +#define SSB_PCMCIA_MEMW_1_SHIFT 8 +#define SSB_PCMCIA_MEMW_2 0x001F0000 /* waitcount2 */ +#define SSB_PCMCIA_MEMW_2_SHIFT 16 +#define SSB_PCMCIA_MEMW_3 0x1F000000 /* waitcount3 */ +#define SSB_PCMCIA_MEMW_3_SHIFT 24 + +/* pcmcia_attrwait */ +#define SSB_PCMCIA_ATTW_0 0x0000003F /* waitcount0 */ +#define SSB_PCMCIA_ATTW_1 0x00001F00 /* waitcount1 */ +#define SSB_PCMCIA_ATTW_1_SHIFT 8 +#define SSB_PCMCIA_ATTW_2 0x001F0000 /* waitcount2 */ +#define SSB_PCMCIA_ATTW_2_SHIFT 16 +#define SSB_PCMCIA_ATTW_3 0x1F000000 /* waitcount3 */ +#define SSB_PCMCIA_ATTW_3_SHIFT 24 + +/* pcmcia_iowait */ +#define SSB_PCMCIA_IOW_0 0x0000003F /* waitcount0 */ +#define SSB_PCMCIA_IOW_1 0x00001F00 /* waitcount1 */ +#define SSB_PCMCIA_IOW_1_SHIFT 8 +#define SSB_PCMCIA_IOW_2 0x001F0000 /* waitcount2 */ +#define SSB_PCMCIA_IOW_2_SHIFT 16 +#define SSB_PCMCIA_IOW_3 0x1F000000 /* waitcount3 */ +#define SSB_PCMCIA_IOW_3_SHIFT 24 + +/* prog_waitcount */ +#define SSB_PROG_WCNT_0 0x0000001F /* waitcount0 */ +#define SSB_PROG_WCNT_1 0x00001F00 /* waitcount1 */ +#define SSB_PROG_WCNT_1_SHIFT 8 +#define SSB_PROG_WCNT_2 0x001F0000 /* waitcount2 */ +#define SSB_PROG_WCNT_2_SHIFT 16 +#define SSB_PROG_WCNT_3 0x1F000000 /* waitcount3 */ +#define SSB_PROG_WCNT_3_SHIFT 24 + +#define SSB_PROG_W0 0x0000000C +#define SSB_PROG_W1 0x00000A00 +#define SSB_PROG_W2 0x00020000 +#define SSB_PROG_W3 0x01000000 + +/* flash_waitcount */ +#define SSB_FLASH_WCNT_0 0x0000001F /* waitcount0 */ +#define SSB_FLASH_WCNT_1 0x00001F00 /* waitcount1 */ +#define SSB_FLASH_WCNT_1_SHIFT 8 +#define SSB_FLASH_WCNT_2 0x001F0000 /* waitcount2 */ +#define SSB_FLASH_WCNT_2_SHIFT 16 +#define SSB_FLASH_WCNT_3 0x1F000000 /* waitcount3 */ +#define SSB_FLASH_WCNT_3_SHIFT 24 + +/* watchdog */ +#define SSB_EXTIF_WATCHDOG_CLK 48000000 /* Hz */ + + + +#ifdef CONFIG_SSB_DRIVER_EXTIF + +struct ssb_extif { + struct ssb_device *dev; +}; + +static inline bool ssb_extif_available(struct ssb_extif *extif) +{ + return (extif->dev != NULL); +} + +extern void ssb_extif_get_clockcontrol(struct ssb_extif *extif, + u32 *plltype, u32 *n, u32 *m); + +extern void ssb_extif_timing_init(struct ssb_extif *extif, + unsigned long ns); + +u32 ssb_extif_gpio_in(struct ssb_extif *extif, u32 mask); + +void ssb_extif_gpio_out(struct ssb_extif *extif, u32 mask, u32 value); + +void ssb_extif_gpio_outen(struct ssb_extif *extif, u32 mask, u32 value); + +#ifdef CONFIG_SSB_SERIAL +extern int ssb_extif_serial_init(struct ssb_extif *extif, + struct ssb_serial_port *ports); +#endif /* CONFIG_SSB_SERIAL */ + + +#else /* CONFIG_SSB_DRIVER_EXTIF */ +/* extif disabled */ + +struct ssb_extif { +}; + +static inline bool ssb_extif_available(struct ssb_extif *extif) +{ + return 0; +} + +static inline +void ssb_extif_get_clockcontrol(struct ssb_extif *extif, + u32 *plltype, u32 *n, u32 *m) +{ +} + +#endif /* CONFIG_SSB_DRIVER_EXTIF */ +#endif /* LINUX_SSB_EXTIFCORE_H_ */ diff --git a/include/linux/ssb/ssb_driver_mips.h b/include/linux/ssb/ssb_driver_mips.h new file mode 100644 index 000000000000..5f44e9740cd2 --- /dev/null +++ b/include/linux/ssb/ssb_driver_mips.h @@ -0,0 +1,46 @@ +#ifndef LINUX_SSB_MIPSCORE_H_ +#define LINUX_SSB_MIPSCORE_H_ + +#ifdef CONFIG_SSB_DRIVER_MIPS + +struct ssb_device; + +struct ssb_serial_port { + void *regs; + unsigned long clockspeed; + unsigned int irq; + unsigned int baud_base; + unsigned int reg_shift; +}; + + +struct ssb_mipscore { + struct ssb_device *dev; + + int nr_serial_ports; + struct ssb_serial_port serial_ports[4]; + + u8 flash_buswidth; + u32 flash_window; + u32 flash_window_size; +}; + +extern void ssb_mipscore_init(struct ssb_mipscore *mcore); +extern u32 ssb_cpu_clock(struct ssb_mipscore *mcore); + +extern unsigned int ssb_mips_irq(struct ssb_device *dev); + + +#else /* CONFIG_SSB_DRIVER_MIPS */ + +struct ssb_mipscore { +}; + +static inline +void ssb_mipscore_init(struct ssb_mipscore *mcore) +{ +} + +#endif /* CONFIG_SSB_DRIVER_MIPS */ + +#endif /* LINUX_SSB_MIPSCORE_H_ */ diff --git a/include/linux/ssb/ssb_driver_pci.h b/include/linux/ssb/ssb_driver_pci.h new file mode 100644 index 000000000000..9cfffb7b1a27 --- /dev/null +++ b/include/linux/ssb/ssb_driver_pci.h @@ -0,0 +1,106 @@ +#ifndef LINUX_SSB_PCICORE_H_ +#define LINUX_SSB_PCICORE_H_ + +#ifdef CONFIG_SSB_DRIVER_PCICORE + +/* PCI core registers. */ +#define SSB_PCICORE_CTL 0x0000 /* PCI Control */ +#define SSB_PCICORE_CTL_RST_OE 0x00000001 /* PCI_RESET Output Enable */ +#define SSB_PCICORE_CTL_RST 0x00000002 /* PCI_RESET driven out to pin */ +#define SSB_PCICORE_CTL_CLK_OE 0x00000004 /* Clock gate Output Enable */ +#define SSB_PCICORE_CTL_CLK 0x00000008 /* Gate for clock driven out to pin */ +#define SSB_PCICORE_ARBCTL 0x0010 /* PCI Arbiter Control */ +#define SSB_PCICORE_ARBCTL_INTERN 0x00000001 /* Use internal arbiter */ +#define SSB_PCICORE_ARBCTL_EXTERN 0x00000002 /* Use external arbiter */ +#define SSB_PCICORE_ARBCTL_PARKID 0x00000006 /* Mask, selects which agent is parked on an idle bus */ +#define SSB_PCICORE_ARBCTL_PARKID_LAST 0x00000000 /* Last requestor */ +#define SSB_PCICORE_ARBCTL_PARKID_4710 0x00000002 /* 4710 */ +#define SSB_PCICORE_ARBCTL_PARKID_EXT0 0x00000004 /* External requestor 0 */ +#define SSB_PCICORE_ARBCTL_PARKID_EXT1 0x00000006 /* External requestor 1 */ +#define SSB_PCICORE_ISTAT 0x0020 /* Interrupt status */ +#define SSB_PCICORE_ISTAT_INTA 0x00000001 /* PCI INTA# */ +#define SSB_PCICORE_ISTAT_INTB 0x00000002 /* PCI INTB# */ +#define SSB_PCICORE_ISTAT_SERR 0x00000004 /* PCI SERR# (write to clear) */ +#define SSB_PCICORE_ISTAT_PERR 0x00000008 /* PCI PERR# (write to clear) */ +#define SSB_PCICORE_ISTAT_PME 0x00000010 /* PCI PME# */ +#define SSB_PCICORE_IMASK 0x0024 /* Interrupt mask */ +#define SSB_PCICORE_IMASK_INTA 0x00000001 /* PCI INTA# */ +#define SSB_PCICORE_IMASK_INTB 0x00000002 /* PCI INTB# */ +#define SSB_PCICORE_IMASK_SERR 0x00000004 /* PCI SERR# */ +#define SSB_PCICORE_IMASK_PERR 0x00000008 /* PCI PERR# */ +#define SSB_PCICORE_IMASK_PME 0x00000010 /* PCI PME# */ +#define SSB_PCICORE_MBOX 0x0028 /* Backplane to PCI Mailbox */ +#define SSB_PCICORE_MBOX_F0_0 0x00000100 /* PCI function 0, INT 0 */ +#define SSB_PCICORE_MBOX_F0_1 0x00000200 /* PCI function 0, INT 1 */ +#define SSB_PCICORE_MBOX_F1_0 0x00000400 /* PCI function 1, INT 0 */ +#define SSB_PCICORE_MBOX_F1_1 0x00000800 /* PCI function 1, INT 1 */ +#define SSB_PCICORE_MBOX_F2_0 0x00001000 /* PCI function 2, INT 0 */ +#define SSB_PCICORE_MBOX_F2_1 0x00002000 /* PCI function 2, INT 1 */ +#define SSB_PCICORE_MBOX_F3_0 0x00004000 /* PCI function 3, INT 0 */ +#define SSB_PCICORE_MBOX_F3_1 0x00008000 /* PCI function 3, INT 1 */ +#define SSB_PCICORE_BCAST_ADDR 0x0050 /* Backplane Broadcast Address */ +#define SSB_PCICORE_BCAST_ADDR_MASK 0x000000FF +#define SSB_PCICORE_BCAST_DATA 0x0054 /* Backplane Broadcast Data */ +#define SSB_PCICORE_GPIO_IN 0x0060 /* rev >= 2 only */ +#define SSB_PCICORE_GPIO_OUT 0x0064 /* rev >= 2 only */ +#define SSB_PCICORE_GPIO_ENABLE 0x0068 /* rev >= 2 only */ +#define SSB_PCICORE_GPIO_CTL 0x006C /* rev >= 2 only */ +#define SSB_PCICORE_SBTOPCI0 0x0100 /* Backplane to PCI translation 0 (sbtopci0) */ +#define SSB_PCICORE_SBTOPCI0_MASK 0xFC000000 +#define SSB_PCICORE_SBTOPCI1 0x0104 /* Backplane to PCI translation 1 (sbtopci1) */ +#define SSB_PCICORE_SBTOPCI1_MASK 0xFC000000 +#define SSB_PCICORE_SBTOPCI2 0x0108 /* Backplane to PCI translation 2 (sbtopci2) */ +#define SSB_PCICORE_SBTOPCI2_MASK 0xC0000000 + +/* SBtoPCIx */ +#define SSB_PCICORE_SBTOPCI_MEM 0x00000000 +#define SSB_PCICORE_SBTOPCI_IO 0x00000001 +#define SSB_PCICORE_SBTOPCI_CFG0 0x00000002 +#define SSB_PCICORE_SBTOPCI_CFG1 0x00000003 +#define SSB_PCICORE_SBTOPCI_PREF 0x00000004 /* Prefetch enable */ +#define SSB_PCICORE_SBTOPCI_BURST 0x00000008 /* Burst enable */ +#define SSB_PCICORE_SBTOPCI_MRM 0x00000020 /* Memory Read Multiple */ +#define SSB_PCICORE_SBTOPCI_RC 0x00000030 /* Read Command mask (rev >= 11) */ +#define SSB_PCICORE_SBTOPCI_RC_READ 0x00000000 /* Memory read */ +#define SSB_PCICORE_SBTOPCI_RC_READL 0x00000010 /* Memory read line */ +#define SSB_PCICORE_SBTOPCI_RC_READM 0x00000020 /* Memory read multiple */ + + +/* PCIcore specific boardflags */ +#define SSB_PCICORE_BFL_NOPCI 0x00000400 /* Board leaves PCI floating */ + + +struct ssb_pcicore { + struct ssb_device *dev; + u8 setup_done:1; + u8 hostmode:1; + u8 cardbusmode:1; +}; + +extern void ssb_pcicore_init(struct ssb_pcicore *pc); + +/* Enable IRQ routing for a specific device */ +extern int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc, + struct ssb_device *dev); + + +#else /* CONFIG_SSB_DRIVER_PCICORE */ + + +struct ssb_pcicore { +}; + +static inline +void ssb_pcicore_init(struct ssb_pcicore *pc) +{ +} + +static inline +int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc, + struct ssb_device *dev) +{ + return 0; +} + +#endif /* CONFIG_SSB_DRIVER_PCICORE */ +#endif /* LINUX_SSB_PCICORE_H_ */ diff --git a/include/linux/ssb/ssb_regs.h b/include/linux/ssb/ssb_regs.h new file mode 100644 index 000000000000..47c7c71a5acf --- /dev/null +++ b/include/linux/ssb/ssb_regs.h @@ -0,0 +1,292 @@ +#ifndef LINUX_SSB_REGS_H_ +#define LINUX_SSB_REGS_H_ + + +/* SiliconBackplane Address Map. + * All regions may not exist on all chips. + */ +#define SSB_SDRAM_BASE 0x00000000U /* Physical SDRAM */ +#define SSB_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */ +#define SSB_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */ +#define SSB_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */ +#define SSB_ENUM_BASE 0x18000000U /* Enumeration space base */ +#define SSB_ENUM_LIMIT 0x18010000U /* Enumeration space limit */ + +#define SSB_FLASH2 0x1c000000U /* Flash Region 2 (region 1 shadowed here) */ +#define SSB_FLASH2_SZ 0x02000000U /* Size of Flash Region 2 */ + +#define SSB_EXTIF_BASE 0x1f000000U /* External Interface region base address */ +#define SSB_FLASH1 0x1fc00000U /* Flash Region 1 */ +#define SSB_FLASH1_SZ 0x00400000U /* Size of Flash Region 1 */ + +#define SSB_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */ +#define SSB_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */ +#define SSB_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */ +#define SSB_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */ +#define SSB_EUART (SSB_EXTIF_BASE + 0x00800000) +#define SSB_LED (SSB_EXTIF_BASE + 0x00900000) + + +/* Enumeration space constants */ +#define SSB_CORE_SIZE 0x1000 /* Size of a core MMIO area */ +#define SSB_MAX_NR_CORES ((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE) + + +/* mips address */ +#define SSB_EJTAG 0xff200000 /* MIPS EJTAG space (2M) */ + + +/* SSB PCI config space registers. */ +#define SSB_PMCSR 0x44 +#define SSB_PE 0x100 +#define SSB_BAR0_WIN 0x80 /* Backplane address space 0 */ +#define SSB_BAR1_WIN 0x84 /* Backplane address space 1 */ +#define SSB_SPROMCTL 0x88 /* SPROM control */ +#define SSB_SPROMCTL_WE 0x10 /* SPROM write enable */ +#define SSB_BAR1_CONTROL 0x8c /* Address space 1 burst control */ +#define SSB_PCI_IRQS 0x90 /* PCI interrupts */ +#define SSB_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */ +#define SSB_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */ +#define SSB_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */ +#define SSB_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */ +#define SSB_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */ +#define SSB_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */ +#define SSB_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */ +#define SSB_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */ +#define SSB_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */ + + +#define SSB_BAR0_MAX_RETRIES 50 + +/* Silicon backplane configuration register definitions */ +#define SSB_IPSFLAG 0x0F08 +#define SSB_IPSFLAG_IRQ1 0x0000003F /* which sbflags get routed to mips interrupt 1 */ +#define SSB_IPSFLAG_IRQ1_SHIFT 0 +#define SSB_IPSFLAG_IRQ2 0x00003F00 /* which sbflags get routed to mips interrupt 2 */ +#define SSB_IPSFLAG_IRQ2_SHIFT 8 +#define SSB_IPSFLAG_IRQ3 0x003F0000 /* which sbflags get routed to mips interrupt 3 */ +#define SSB_IPSFLAG_IRQ3_SHIFT 16 +#define SSB_IPSFLAG_IRQ4 0x3F000000 /* which sbflags get routed to mips interrupt 4 */ +#define SSB_IPSFLAG_IRQ4_SHIFT 24 +#define SSB_TPSFLAG 0x0F18 +#define SSB_TPSFLAG_BPFLAG 0x0000003F /* Backplane flag # */ +#define SSB_TPSFLAG_ALWAYSIRQ 0x00000040 /* IRQ is always sent on the Backplane */ +#define SSB_TMERRLOGA 0x0F48 +#define SSB_TMERRLOG 0x0F50 +#define SSB_ADMATCH3 0x0F60 +#define SSB_ADMATCH2 0x0F68 +#define SSB_ADMATCH1 0x0F70 +#define SSB_IMSTATE 0x0F90 /* SB Initiator Agent State */ +#define SSB_IMSTATE_PC 0x0000000f /* Pipe Count */ +#define SSB_IMSTATE_AP_MASK 0x00000030 /* Arbitration Priority */ +#define SSB_IMSTATE_AP_BOTH 0x00000000 /* Use both timeslices and token */ +#define SSB_IMSTATE_AP_TS 0x00000010 /* Use timeslices only */ +#define SSB_IMSTATE_AP_TK 0x00000020 /* Use token only */ +#define SSB_IMSTATE_AP_RSV 0x00000030 /* Reserved */ +#define SSB_IMSTATE_IBE 0x00020000 /* In Band Error */ +#define SSB_IMSTATE_TO 0x00040000 /* Timeout */ +#define SSB_INTVEC 0x0F94 /* SB Interrupt Mask */ +#define SSB_INTVEC_PCI 0x00000001 /* Enable interrupts for PCI */ +#define SSB_INTVEC_ENET0 0x00000002 /* Enable interrupts for enet 0 */ +#define SSB_INTVEC_ILINE20 0x00000004 /* Enable interrupts for iline20 */ +#define SSB_INTVEC_CODEC 0x00000008 /* Enable interrupts for v90 codec */ +#define SSB_INTVEC_USB 0x00000010 /* Enable interrupts for usb */ +#define SSB_INTVEC_EXTIF 0x00000020 /* Enable interrupts for external i/f */ +#define SSB_INTVEC_ENET1 0x00000040 /* Enable interrupts for enet 1 */ +#define SSB_TMSLOW 0x0F98 /* SB Target State Low */ +#define SSB_TMSLOW_RESET 0x00000001 /* Reset */ +#define SSB_TMSLOW_REJECT_22 0x00000002 /* Reject (Backplane rev 2.2) */ +#define SSB_TMSLOW_REJECT_23 0x00000004 /* Reject (Backplane rev 2.3) */ +#define SSB_TMSLOW_CLOCK 0x00010000 /* Clock Enable */ +#define SSB_TMSLOW_FGC 0x00020000 /* Force Gated Clocks On */ +#define SSB_TMSLOW_PE 0x40000000 /* Power Management Enable */ +#define SSB_TMSLOW_BE 0x80000000 /* BIST Enable */ +#define SSB_TMSHIGH 0x0F9C /* SB Target State High */ +#define SSB_TMSHIGH_SERR 0x00000001 /* S-error */ +#define SSB_TMSHIGH_INT 0x00000002 /* Interrupt */ +#define SSB_TMSHIGH_BUSY 0x00000004 /* Busy */ +#define SSB_TMSHIGH_TO 0x00000020 /* Timeout. Backplane rev >= 2.3 only */ +#define SSB_TMSHIGH_COREFL 0x1FFF0000 /* Core specific flags */ +#define SSB_TMSHIGH_COREFL_SHIFT 16 +#define SSB_TMSHIGH_DMA64 0x10000000 /* 64bit DMA supported */ +#define SSB_TMSHIGH_GCR 0x20000000 /* Gated Clock Request */ +#define SSB_TMSHIGH_BISTF 0x40000000 /* BIST Failed */ +#define SSB_TMSHIGH_BISTD 0x80000000 /* BIST Done */ +#define SSB_BWA0 0x0FA0 +#define SSB_IMCFGLO 0x0FA8 +#define SSB_IMCFGLO_SERTO 0x00000007 /* Service timeout */ +#define SSB_IMCFGLO_REQTO 0x00000070 /* Request timeout */ +#define SSB_IMCFGLO_REQTO_SHIFT 4 +#define SSB_IMCFGLO_CONNID 0x00FF0000 /* Connection ID */ +#define SSB_IMCFGLO_CONNID_SHIFT 16 +#define SSB_IMCFGHI 0x0FAC +#define SSB_ADMATCH0 0x0FB0 +#define SSB_TMCFGLO 0x0FB8 +#define SSB_TMCFGHI 0x0FBC +#define SSB_BCONFIG 0x0FC0 +#define SSB_BSTATE 0x0FC8 +#define SSB_ACTCFG 0x0FD8 +#define SSB_FLAGST 0x0FE8 +#define SSB_IDLOW 0x0FF8 +#define SSB_IDLOW_CFGSP 0x00000003 /* Config Space */ +#define SSB_IDLOW_ADDRNGE 0x00000038 /* Address Ranges supported */ +#define SSB_IDLOW_ADDRNGE_SHIFT 3 +#define SSB_IDLOW_SYNC 0x00000040 +#define SSB_IDLOW_INITIATOR 0x00000080 +#define SSB_IDLOW_MIBL 0x00000F00 /* Minimum Backplane latency */ +#define SSB_IDLOW_MIBL_SHIFT 8 +#define SSB_IDLOW_MABL 0x0000F000 /* Maximum Backplane latency */ +#define SSB_IDLOW_MABL_SHIFT 12 +#define SSB_IDLOW_TIF 0x00010000 /* This Initiator is first */ +#define SSB_IDLOW_CCW 0x000C0000 /* Cycle counter width */ +#define SSB_IDLOW_CCW_SHIFT 18 +#define SSB_IDLOW_TPT 0x00F00000 /* Target ports */ +#define SSB_IDLOW_TPT_SHIFT 20 +#define SSB_IDLOW_INITP 0x0F000000 /* Initiator ports */ +#define SSB_IDLOW_INITP_SHIFT 24 +#define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ +#define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ +#define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ +#define SSB_IDHIGH 0x0FFC /* SB Identification High */ +#define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ +#define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ +#define SSB_IDHIGH_CC_SHIFT 4 +#define SSB_IDHIGH_RCHI 0x00007000 /* Revision Code (high part) */ +#define SSB_IDHIGH_RCHI_SHIFT 8 /* yes, shift 8 is right */ +#define SSB_IDHIGH_VC 0xFFFF0000 /* Vendor Code */ +#define SSB_IDHIGH_VC_SHIFT 16 + +/* SPROM shadow area. If not otherwise noted, fields are + * two bytes wide. Note that the SPROM can _only_ be read + * in two-byte quantinies. + */ +#define SSB_SPROMSIZE_WORDS 64 +#define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16)) +#define SSB_SPROM_BASE 0x1000 +#define SSB_SPROM_REVISION 0x107E +#define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */ +#define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */ +#define SSB_SPROM_REVISION_CRC_SHIFT 8 +/* SPROM Revision 1 */ +#define SSB_SPROM1_SPID 0x1004 /* Subsystem Product ID for PCI */ +#define SSB_SPROM1_SVID 0x1006 /* Subsystem Vendor ID for PCI */ +#define SSB_SPROM1_PID 0x1008 /* Product ID for PCI */ +#define SSB_SPROM1_IL0MAC 0x1048 /* 6 bytes MAC address for 802.11b/g */ +#define SSB_SPROM1_ET0MAC 0x104E /* 6 bytes MAC address for Ethernet */ +#define SSB_SPROM1_ET1MAC 0x1054 /* 6 bytes MAC address for 802.11a */ +#define SSB_SPROM1_ETHPHY 0x105A /* Ethernet PHY settings */ +#define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ +#define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ +#define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5 +#define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ +#define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ +#define SSB_SPROM1_BINF 0x105C /* Board info */ +#define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */ +#define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */ +#define SSB_SPROM1_BINF_CCODE_SHIFT 8 +#define SSB_SPROM1_BINF_ANTA 0x3000 /* Available A-PHY antennas */ +#define SSB_SPROM1_BINF_ANTA_SHIFT 12 +#define SSB_SPROM1_BINF_ANTBG 0xC000 /* Available B-PHY antennas */ +#define SSB_SPROM1_BINF_ANTBG_SHIFT 14 +#define SSB_SPROM1_PA0B0 0x105E +#define SSB_SPROM1_PA0B1 0x1060 +#define SSB_SPROM1_PA0B2 0x1062 +#define SSB_SPROM1_GPIOA 0x1064 /* General Purpose IO pins 0 and 1 */ +#define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */ +#define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */ +#define SSB_SPROM1_GPIOA_P1_SHIFT 8 +#define SSB_SPROM1_GPIOB 0x1066 /* General Purpuse IO pins 2 and 3 */ +#define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */ +#define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */ +#define SSB_SPROM1_GPIOB_P3_SHIFT 8 +#define SSB_SPROM1_MAXPWR 0x1068 /* Power Amplifier Max Power */ +#define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */ +#define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */ +#define SSB_SPROM1_MAXPWR_A_SHIFT 8 +#define SSB_SPROM1_PA1B0 0x106A +#define SSB_SPROM1_PA1B1 0x106C +#define SSB_SPROM1_PA1B2 0x106E +#define SSB_SPROM1_ITSSI 0x1070 /* Idle TSSI Target */ +#define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/ +#define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */ +#define SSB_SPROM1_ITSSI_A_SHIFT 8 +#define SSB_SPROM1_BFLLO 0x1072 /* Boardflags (low 16 bits) */ +#define SSB_SPROM1_AGAIN 0x1074 /* Antenna Gain (in dBm Q5.2) */ +#define SSB_SPROM1_AGAIN_A 0x00FF /* A-PHY */ +#define SSB_SPROM1_AGAIN_BG 0xFF00 /* B-PHY and G-PHY */ +#define SSB_SPROM1_AGAIN_BG_SHIFT 8 +#define SSB_SPROM1_OEM 0x1076 /* 8 bytes OEM string (rev 1 only) */ +/* SPROM Revision 2 (inherits from rev 1) */ +#define SSB_SPROM2_BFLHI 0x1038 /* Boardflags (high 16 bits) */ +#define SSB_SPROM2_MAXP_A 0x103A /* A-PHY Max Power */ +#define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */ +#define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */ +#define SSB_SPROM2_MAXP_A_LO_SHIFT 8 +#define SSB_SPROM2_PA1LOB0 0x103C /* A-PHY PowerAmplifier Low Settings */ +#define SSB_SPROM2_PA1LOB1 0x103E /* A-PHY PowerAmplifier Low Settings */ +#define SSB_SPROM2_PA1LOB2 0x1040 /* A-PHY PowerAmplifier Low Settings */ +#define SSB_SPROM2_PA1HIB0 0x1042 /* A-PHY PowerAmplifier High Settings */ +#define SSB_SPROM2_PA1HIB1 0x1044 /* A-PHY PowerAmplifier High Settings */ +#define SSB_SPROM2_PA1HIB2 0x1046 /* A-PHY PowerAmplifier High Settings */ +#define SSB_SPROM2_OPO 0x1078 /* OFDM Power Offset from CCK Level */ +#define SSB_SPROM2_OPO_VALUE 0x00FF +#define SSB_SPROM2_OPO_UNUSED 0xFF00 +#define SSB_SPROM2_CCODE 0x107C /* Two char Country Code */ +/* SPROM Revision 3 (inherits from rev 2) */ +#define SSB_SPROM3_OFDMAPO 0x102C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */ +#define SSB_SPROM3_OFDMALPO 0x1030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */ +#define SSB_SPROM3_OFDMAHPO 0x1034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */ +#define SSB_SPROM3_GPIOLDC 0x1042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */ +#define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */ +#define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8 +#define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */ +#define SSB_SPROM3_GPIOLDC_ON_SHIFT 16 +#define SSB_SPROM3_CCKPO 0x1078 /* CCK Power Offset */ +#define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */ +#define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */ +#define SSB_SPROM3_CCKPO_2M_SHIFT 4 +#define SSB_SPROM3_CCKPO_55M 0x0F00 /* 5.5M Rate PO */ +#define SSB_SPROM3_CCKPO_55M_SHIFT 8 +#define SSB_SPROM3_CCKPO_11M 0xF000 /* 11M Rate PO */ +#define SSB_SPROM3_CCKPO_11M_SHIFT 12 +#define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */ + +/* Values for SSB_SPROM1_BINF_CCODE */ +enum { + SSB_SPROM1CCODE_WORLD = 0, + SSB_SPROM1CCODE_THAILAND, + SSB_SPROM1CCODE_ISRAEL, + SSB_SPROM1CCODE_JORDAN, + SSB_SPROM1CCODE_CHINA, + SSB_SPROM1CCODE_JAPAN, + SSB_SPROM1CCODE_USA_CANADA_ANZ, + SSB_SPROM1CCODE_EUROPE, + SSB_SPROM1CCODE_USA_LOW, + SSB_SPROM1CCODE_JAPAN_HIGH, + SSB_SPROM1CCODE_ALL, + SSB_SPROM1CCODE_NONE, +}; + +/* Address-Match values and masks (SSB_ADMATCHxxx) */ +#define SSB_ADM_TYPE 0x00000003 /* Address type */ +#define SSB_ADM_TYPE0 0 +#define SSB_ADM_TYPE1 1 +#define SSB_ADM_TYPE2 2 +#define SSB_ADM_AD64 0x00000004 +#define SSB_ADM_SZ0 0x000000F8 /* Type0 size */ +#define SSB_ADM_SZ0_SHIFT 3 +#define SSB_ADM_SZ1 0x000001F8 /* Type1 size */ +#define SSB_ADM_SZ1_SHIFT 3 +#define SSB_ADM_SZ2 0x000001F8 /* Type2 size */ +#define SSB_ADM_SZ2_SHIFT 3 +#define SSB_ADM_EN 0x00000400 /* Enable */ +#define SSB_ADM_NEG 0x00000800 /* Negative decode */ +#define SSB_ADM_BASE0 0xFFFFFF00 /* Type0 base address */ +#define SSB_ADM_BASE0_SHIFT 8 +#define SSB_ADM_BASE1 0xFFFFF000 /* Type1 base address for the core */ +#define SSB_ADM_BASE1_SHIFT 12 +#define SSB_ADM_BASE2 0xFFFF0000 /* Type2 base address for the core */ +#define SSB_ADM_BASE2_SHIFT 16 + + +#endif /* LINUX_SSB_REGS_H_ */ |
