diff options
Diffstat (limited to 'include/linux/mtd/nand.h')
| -rw-r--r-- | include/linux/mtd/nand.h | 92 |
1 files changed, 43 insertions, 49 deletions
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index c2b9ac4fbc4a..904131bab501 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -42,10 +42,10 @@ extern void nand_release(struct mtd_info *mtd); /* Internal helper for board drivers which need to override command function */ extern void nand_wait_ready(struct mtd_info *mtd); -/* locks all blockes present in the device */ +/* locks all blocks present in the device */ extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len); -/* unlocks specified locked blockes */ +/* unlocks specified locked blocks */ extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len); /* The maximum number of NAND chips in an array */ @@ -150,7 +150,7 @@ typedef enum { #define NAND_ECC_READ 0 /* Reset Hardware ECC for write */ #define NAND_ECC_WRITE 1 -/* Enable Hardware ECC before syndrom is read back from flash */ +/* Enable Hardware ECC before syndrome is read back from flash */ #define NAND_ECC_READSYN 2 /* Bit mask for flags passed to do_nand_read_ecc */ @@ -163,7 +163,7 @@ typedef enum { */ /* Chip can not auto increment pages */ #define NAND_NO_AUTOINCR 0x00000001 -/* Buswitdh is 16 bit */ +/* Buswidth is 16 bit */ #define NAND_BUSWIDTH_16 0x00000002 /* Device supports partial programming without padding */ #define NAND_NO_PADDING 0x00000004 @@ -219,27 +219,15 @@ typedef enum { #define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR) /* Non chip related options */ -/* - * Use a flash based bad block table. OOB identifier is saved in OOB area. - * This option is passed to the default bad block table function. - */ -#define NAND_USE_FLASH_BBT 0x00010000 /* This option skips the bbt scan during initialization. */ -#define NAND_SKIP_BBTSCAN 0x00020000 +#define NAND_SKIP_BBTSCAN 0x00010000 /* * This option is defined if the board driver allocates its own buffers * (e.g. because it needs them DMA-coherent). */ -#define NAND_OWN_BUFFERS 0x00040000 +#define NAND_OWN_BUFFERS 0x00020000 /* Chip may not exist, so silence any errors in scan */ -#define NAND_SCAN_SILENT_NODEV 0x00080000 -/* - * If passed additionally to NAND_USE_FLASH_BBT then BBT code will not touch - * the OOB area. - */ -#define NAND_USE_FLASH_BBT_NO_OOB 0x00800000 -/* Create an empty BBT with no vendor information if the BBT is available */ -#define NAND_CREATE_EMPTY_BBT 0x01000000 +#define NAND_SCAN_SILENT_NODEV 0x00040000 /* Options set by nand scan */ /* Nand scan has allocated controller struct */ @@ -331,27 +319,29 @@ struct nand_hw_control { }; /** - * struct nand_ecc_ctrl - Control structure for ecc - * @mode: ecc mode - * @steps: number of ecc steps per page - * @size: data bytes per ecc step - * @bytes: ecc bytes per step - * @total: total number of ecc bytes per page - * @prepad: padding information for syndrome based ecc generators - * @postpad: padding information for syndrome based ecc generators + * struct nand_ecc_ctrl - Control structure for ECC + * @mode: ECC mode + * @steps: number of ECC steps per page + * @size: data bytes per ECC step + * @bytes: ECC bytes per step + * @total: total number of ECC bytes per page + * @prepad: padding information for syndrome based ECC generators + * @postpad: padding information for syndrome based ECC generators * @layout: ECC layout control struct pointer - * @priv: pointer to private ecc control data - * @hwctl: function to control hardware ecc generator. Must only + * @priv: pointer to private ECC control data + * @hwctl: function to control hardware ECC generator. Must only * be provided if an hardware ECC is available - * @calculate: function for ecc calculation or readback from ecc hardware - * @correct: function for ecc correction, matching to ecc generator (sw/hw) + * @calculate: function for ECC calculation or readback from ECC hardware + * @correct: function for ECC correction, matching to ECC generator (sw/hw) * @read_page_raw: function to read a raw page without ECC * @write_page_raw: function to write a raw page without ECC - * @read_page: function to read a page according to the ecc generator + * @read_page: function to read a page according to the ECC generator * requirements. * @read_subpage: function to read parts of the page covered by ECC. - * @write_page: function to write a page according to the ecc generator + * @write_page: function to write a page according to the ECC generator * requirements. + * @write_oob_raw: function to write chip OOB data without ECC + * @read_oob_raw: function to read chip OOB data without ECC * @read_oob: function to read chip OOB data * @write_oob: function to write chip OOB data */ @@ -380,6 +370,10 @@ struct nand_ecc_ctrl { uint32_t offs, uint32_t len, uint8_t *buf); void (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf); + int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, + int page); + int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, + int page, int sndcmd); int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page, int sndcmd); int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip, @@ -388,8 +382,8 @@ struct nand_ecc_ctrl { /** * struct nand_buffers - buffer structure for read/write - * @ecccalc: buffer for calculated ecc - * @ecccode: buffer for ecc read from flash + * @ecccalc: buffer for calculated ECC + * @ecccode: buffer for ECC read from flash * @databuf: buffer for data - dynamically sized * * Do not change the order of buffers. databuf and oobrbuf must be in @@ -422,7 +416,7 @@ struct nand_buffers { * mtd->oobsize, mtd->writesize and so on. * @id_data contains the 8 bytes values of NAND_CMD_READID. * Return with the bus width. - * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing + * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing * device ready/busy line. If set to NULL no access to * ready/busy is available and the ready/busy information * is read from the chip status register. @@ -430,17 +424,17 @@ struct nand_buffers { * commands to the chip. * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on * ready. - * @ecc: [BOARDSPECIFIC] ecc control ctructure + * @ecc: [BOARDSPECIFIC] ECC control structure * @buffers: buffer structure for read/write * @hwcontrol: platform-specific hardware control structure - * @ops: oob operation operands * @erase_cmd: [INTERN] erase command write function, selectable due * to AND support. * @scan_bbt: [REPLACEABLE] function to scan bad block table * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring * data from array to read regs (tR). * @state: [INTERN] the current state of the NAND device - * @oob_poi: poison value buffer + * @oob_poi: "poison value buffer," used for laying out OOB data + * before writing * @page_shift: [INTERN] number of address bits in a page (column * address bits). * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock @@ -449,6 +443,9 @@ struct nand_buffers { * @options: [BOARDSPECIFIC] various chip options. They can partly * be set to inform nand_scan about special functionality. * See the defines for further explanation. + * @bbt_options: [INTERN] bad block specific options. All options used + * here must come from bbm.h. By default, these options + * will be copied to the appropriate nand_bbt_descr's. * @badblockpos: [INTERN] position of the bad block marker in the oob * area. * @badblockbits: [INTERN] number of bits to left-shift the bad block @@ -464,7 +461,7 @@ struct nand_buffers { * non 0 if ONFI supported. * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is * supported, 0 otherwise. - * @ecclayout: [REPLACEABLE] the default ecc placement scheme + * @ecclayout: [REPLACEABLE] the default ECC placement scheme * @bbt: [INTERN] bad block table pointer * @bbt_td: [REPLACEABLE] bad block table descriptor for flash * lookup. @@ -472,9 +469,9 @@ struct nand_buffers { * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial * bad block scan. * @controller: [REPLACEABLE] a pointer to a hardware controller - * structure which is shared among multiple independend + * structure which is shared among multiple independent * devices. - * @priv: [OPTIONAL] pointer to private chip date + * @priv: [OPTIONAL] pointer to private chip data * @errstat: [OPTIONAL] hardware specific function to perform * additional error status checks (determine if errors are * correctable). @@ -509,6 +506,7 @@ struct nand_chip { int chip_delay; unsigned int options; + unsigned int bbt_options; int page_shift; int phys_erase_shift; @@ -536,8 +534,6 @@ struct nand_chip { struct nand_buffers *buffers; struct nand_hw_control hwcontrol; - struct mtd_oob_ops ops; - uint8_t *bbt; struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; @@ -611,10 +607,9 @@ extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, * @partitions: mtd partition list * @chip_delay: R/B delay value in us * @options: Option flags, e.g. 16bit buswidth - * @ecclayout: ecc layout info structure + * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH + * @ecclayout: ECC layout info structure * @part_probe_types: NULL-terminated array of probe types - * @set_parts: platform specific function to set partitions - * @priv: hardware controller specific settings */ struct platform_nand_chip { int nr_chips; @@ -624,9 +619,8 @@ struct platform_nand_chip { struct nand_ecclayout *ecclayout; int chip_delay; unsigned int options; + unsigned int bbt_options; const char **part_probe_types; - void (*set_parts)(uint64_t size, struct platform_nand_chip *chip); - void *priv; }; /* Keep gcc happy */ |
