diff options
Diffstat (limited to 'include/asm-mips/sn/sn0')
| -rw-r--r-- | include/asm-mips/sn/sn0/addrs.h | 288 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/arch.h | 72 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/hub.h | 40 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/hubio.h | 972 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/hubmd.h | 789 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/hubni.h | 255 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/hubpi.h | 409 | ||||
| -rw-r--r-- | include/asm-mips/sn/sn0/ip27.h | 85 |
8 files changed, 0 insertions, 2910 deletions
diff --git a/include/asm-mips/sn/sn0/addrs.h b/include/asm-mips/sn/sn0/addrs.h deleted file mode 100644 index b06190093bbc..000000000000 --- a/include/asm-mips/sn/sn0/addrs.h +++ /dev/null @@ -1,288 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/addrs.h>, revision 1.126. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_ADDRS_H -#define _ASM_SN_SN0_ADDRS_H - - -/* - * SN0 (on a T5) Address map - * - * This file contains a set of definitions and macros which are used - * to reference into the major address spaces (CAC, HSPEC, IO, MSPEC, - * and UNCAC) used by the SN0 architecture. It also contains addresses - * for "major" statically locatable PROM/Kernel data structures, such as - * the partition table, the configuration data structure, etc. - * We make an implicit assumption that the processor using this file - * follows the R10K's provisions for specifying uncached attributes; - * should this change, the base registers may very well become processor- - * dependent. - * - * For more information on the address spaces, see the "Local Resources" - * chapter of the Hub specification. - * - * NOTE: This header file is included both by C and by assembler source - * files. Please bracket any language-dependent definitions - * appropriately. - */ - -/* - * Some of the macros here need to be casted to appropriate types when used - * from C. They definitely must not be casted from assembly language so we - * use some new ANSI preprocessor stuff to paste these on where needed. - */ - -/* - * The following couple of definitions will eventually need to be variables, - * since the amount of address space assigned to each node depends on - * whether the system is running in N-mode (more nodes with less memory) - * or M-mode (fewer nodes with more memory). We expect that it will - * be a while before we need to make this decision dynamically, though, - * so for now we just use defines bracketed by an ifdef. - */ - -#ifdef CONFIG_SGI_SN_N_MODE - -#define NODE_SIZE_BITS 31 -#define BWIN_SIZE_BITS 28 - -#define NASID_BITS 9 -#define NASID_BITMASK (0x1ffLL) -#define NASID_SHFT 31 -#define NASID_META_BITS 5 -#define NASID_LOCAL_BITS 4 - -#define BDDIR_UPPER_MASK (UINT64_CAST 0x7ffff << 10) -#define BDECC_UPPER_MASK (UINT64_CAST 0x3ffffff << 3) - -#else /* !defined(CONFIG_SGI_SN_N_MODE), assume that M-mode is desired */ - -#define NODE_SIZE_BITS 32 -#define BWIN_SIZE_BITS 29 - -#define NASID_BITMASK (0xffLL) -#define NASID_BITS 8 -#define NASID_SHFT 32 -#define NASID_META_BITS 4 -#define NASID_LOCAL_BITS 4 - -#define BDDIR_UPPER_MASK (UINT64_CAST 0xfffff << 10) -#define BDECC_UPPER_MASK (UINT64_CAST 0x7ffffff << 3) - -#endif /* !defined(CONFIG_SGI_SN_N_MODE) */ - -#define NODE_ADDRSPACE_SIZE (UINT64_CAST 1 << NODE_SIZE_BITS) - -#define NASID_MASK (UINT64_CAST NASID_BITMASK << NASID_SHFT) -#define NASID_GET(_pa) (int) ((UINT64_CAST (_pa) >> \ - NASID_SHFT) & NASID_BITMASK) - -#if !defined(__ASSEMBLY__) - -#define NODE_SWIN_BASE(nasid, widget) \ - ((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN) \ - : RAW_NODE_SWIN_BASE(nasid, widget)) -#else /* __ASSEMBLY__ */ -#define NODE_SWIN_BASE(nasid, widget) \ - (NODE_IO_BASE(nasid) + (UINT64_CAST(widget) << SWIN_SIZE_BITS)) -#endif /* __ASSEMBLY__ */ - -/* - * The following definitions pertain to the IO special address - * space. They define the location of the big and little windows - * of any given node. - */ - -#define BWIN_INDEX_BITS 3 -#define BWIN_SIZE (UINT64_CAST 1 << BWIN_SIZE_BITS) -#define BWIN_SIZEMASK (BWIN_SIZE - 1) -#define BWIN_WIDGET_MASK 0x7 -#define NODE_BWIN_BASE0(nasid) (NODE_IO_BASE(nasid) + BWIN_SIZE) -#define NODE_BWIN_BASE(nasid, bigwin) (NODE_BWIN_BASE0(nasid) + \ - (UINT64_CAST(bigwin) << BWIN_SIZE_BITS)) - -#define BWIN_WIDGETADDR(addr) ((addr) & BWIN_SIZEMASK) -#define BWIN_WINDOWNUM(addr) (((addr) >> BWIN_SIZE_BITS) & BWIN_WIDGET_MASK) -/* - * Verify if addr belongs to large window address of node with "nasid" - * - * - * NOTE: "addr" is expected to be XKPHYS address, and NOT physical - * address - * - * - */ - -#define NODE_BWIN_ADDR(nasid, addr) \ - (((addr) >= NODE_BWIN_BASE0(nasid)) && \ - ((addr) < (NODE_BWIN_BASE(nasid, HUB_NUM_BIG_WINDOW) + \ - BWIN_SIZE))) - -/* - * The following define the major position-independent aliases used - * in SN0. - * CALIAS -- Varies in size, points to the first n bytes of memory - * on the reader's node. - */ - -#define CALIAS_BASE CAC_BASE - - - -#define BRIDGE_REG_PTR(_base, _off) ((volatile bridgereg_t *) \ - ((__psunsigned_t)(_base) + (__psunsigned_t)(_off))) - -#define SN0_WIDGET_BASE(_nasid, _wid) (NODE_SWIN_BASE((_nasid), (_wid))) - -/* Turn on sable logging for the processors whose bits are set. */ -#define SABLE_LOG_TRIGGER(_map) - -#ifndef __ASSEMBLY__ -#define KERN_NMI_ADDR(nasid, slice) \ - TO_NODE_UNCAC((nasid), IP27_NMI_KREGS_OFFSET + \ - (IP27_NMI_KREGS_CPU_SIZE * (slice))) -#endif /* !__ASSEMBLY__ */ - -#ifdef PROM - -#define MISC_PROM_BASE PHYS_TO_K0(0x01300000) -#define MISC_PROM_SIZE 0x200000 - -#define DIAG_BASE PHYS_TO_K0(0x01500000) -#define DIAG_SIZE 0x300000 - -#define ROUTE_BASE PHYS_TO_K0(0x01800000) -#define ROUTE_SIZE 0x200000 - -#define IP27PROM_FLASH_HDR PHYS_TO_K0(0x01300000) -#define IP27PROM_FLASH_DATA PHYS_TO_K0(0x01301000) -#define IP27PROM_CORP_MAX 32 -#define IP27PROM_CORP PHYS_TO_K0(0x01800000) -#define IP27PROM_CORP_SIZE 0x10000 -#define IP27PROM_CORP_STK PHYS_TO_K0(0x01810000) -#define IP27PROM_CORP_STKSIZE 0x2000 -#define IP27PROM_DECOMP_BUF PHYS_TO_K0(0x01900000) -#define IP27PROM_DECOMP_SIZE 0xfff00 - -#define IP27PROM_BASE PHYS_TO_K0(0x01a00000) -#define IP27PROM_BASE_MAPPED (UNCAC_BASE | 0x1fc00000) -#define IP27PROM_SIZE_MAX 0x100000 - -#define IP27PROM_PCFG PHYS_TO_K0(0x01b00000) -#define IP27PROM_PCFG_SIZE 0xd0000 -#define IP27PROM_ERRDMP PHYS_TO_K1(0x01bd0000) -#define IP27PROM_ERRDMP_SIZE 0xf000 - -#define IP27PROM_INIT_START PHYS_TO_K1(0x01bd0000) -#define IP27PROM_CONSOLE PHYS_TO_K1(0x01bdf000) -#define IP27PROM_CONSOLE_SIZE 0x200 -#define IP27PROM_NETUART PHYS_TO_K1(0x01bdf200) -#define IP27PROM_NETUART_SIZE 0x100 -#define IP27PROM_UNUSED1 PHYS_TO_K1(0x01bdf300) -#define IP27PROM_UNUSED1_SIZE 0x500 -#define IP27PROM_ELSC_BASE_A PHYS_TO_K0(0x01bdf800) -#define IP27PROM_ELSC_BASE_B PHYS_TO_K0(0x01bdfc00) -#define IP27PROM_STACK_A PHYS_TO_K0(0x01be0000) -#define IP27PROM_STACK_B PHYS_TO_K0(0x01bf0000) -#define IP27PROM_STACK_SHFT 16 -#define IP27PROM_STACK_SIZE (1 << IP27PROM_STACK_SHFT) -#define IP27PROM_INIT_END PHYS_TO_K0(0x01c00000) - -#define SLAVESTACK_BASE PHYS_TO_K0(0x01580000) -#define SLAVESTACK_SIZE 0x40000 - -#define ENETBUFS_BASE PHYS_TO_K0(0x01f80000) -#define ENETBUFS_SIZE 0x20000 - -#define IO6PROM_BASE PHYS_TO_K0(0x01c00000) -#define IO6PROM_SIZE 0x400000 -#define IO6PROM_BASE_MAPPED (UNCAC_BASE | 0x11c00000) -#define IO6DPROM_BASE PHYS_TO_K0(0x01c00000) -#define IO6DPROM_SIZE 0x200000 - -#define NODEBUGUNIX_ADDR PHYS_TO_K0(0x00019000) -#define DEBUGUNIX_ADDR PHYS_TO_K0(0x00100000) - -#define IP27PROM_INT_LAUNCH 10 /* and 11 */ -#define IP27PROM_INT_NETUART 12 /* through 17 */ - -#endif /* PROM */ - -/* - * needed by symmon so it needs to be outside #if PROM - */ -#define IP27PROM_ELSC_SHFT 10 -#define IP27PROM_ELSC_SIZE (1 << IP27PROM_ELSC_SHFT) - -/* - * This address is used by IO6PROM to build MemoryDescriptors of - * free memory. This address is important since unix gets loaded - * at this address, and this memory has to be FREE if unix is to - * be loaded. - */ - -#define FREEMEM_BASE PHYS_TO_K0(0x2000000) - -#define IO6PROM_STACK_SHFT 14 /* stack per cpu */ -#define IO6PROM_STACK_SIZE (1 << IO6PROM_STACK_SHFT) - -/* - * IP27 PROM vectors - */ - -#define IP27PROM_ENTRY PHYS_TO_COMPATK1(0x1fc00000) -#define IP27PROM_RESTART PHYS_TO_COMPATK1(0x1fc00008) -#define IP27PROM_SLAVELOOP PHYS_TO_COMPATK1(0x1fc00010) -#define IP27PROM_PODMODE PHYS_TO_COMPATK1(0x1fc00018) -#define IP27PROM_IOC3UARTPOD PHYS_TO_COMPATK1(0x1fc00020) -#define IP27PROM_FLASHLEDS PHYS_TO_COMPATK1(0x1fc00028) -#define IP27PROM_REPOD PHYS_TO_COMPATK1(0x1fc00030) -#define IP27PROM_LAUNCHSLAVE PHYS_TO_COMPATK1(0x1fc00038) -#define IP27PROM_WAITSLAVE PHYS_TO_COMPATK1(0x1fc00040) -#define IP27PROM_POLLSLAVE PHYS_TO_COMPATK1(0x1fc00048) - -#define KL_UART_BASE LOCAL_HUB_ADDR(MD_UREG0_0) /* base of UART regs */ -#define KL_UART_CMD LOCAL_HUB_ADDR(MD_UREG0_0) /* UART command reg */ -#define KL_UART_DATA LOCAL_HUB_ADDR(MD_UREG0_1) /* UART data reg */ -#define KL_I2C_REG MD_UREG0_0 /* I2C reg */ - -#ifndef __ASSEMBLY__ - -/* Address 0x400 to 0x1000 ualias points to cache error eframe + misc - * CACHE_ERR_SP_PTR could either contain an address to the stack, or - * the stack could start at CACHE_ERR_SP_PTR - */ -#if defined(HUB_ERR_STS_WAR) -#define CACHE_ERR_EFRAME 0x480 -#else /* HUB_ERR_STS_WAR */ -#define CACHE_ERR_EFRAME 0x400 -#endif /* HUB_ERR_STS_WAR */ - -#define CACHE_ERR_ECCFRAME (CACHE_ERR_EFRAME + EF_SIZE) -#define CACHE_ERR_SP_PTR (0x1000 - 32) /* why -32? TBD */ -#define CACHE_ERR_IBASE_PTR (0x1000 - 40) -#define CACHE_ERR_SP (CACHE_ERR_SP_PTR - 16) -#define CACHE_ERR_AREA_SIZE (ARCS_SPB_OFFSET - CACHE_ERR_EFRAME) - -#endif /* !__ASSEMBLY__ */ - -#define _ARCSPROM - -#if defined(HUB_ERR_STS_WAR) - -#define ERR_STS_WAR_REGISTER IIO_IIBUSERR -#define ERR_STS_WAR_ADDR LOCAL_HUB_ADDR(IIO_IIBUSERR) -#define ERR_STS_WAR_PHYSADDR TO_PHYS((__psunsigned_t)ERR_STS_WAR_ADDR) - /* Used to match addr in error reg. */ -#define OLD_ERR_STS_WAR_OFFSET ((MD_MEM_BANKS * MD_BANK_SIZE) - 0x100) - -#endif /* HUB_ERR_STS_WAR */ - -#endif /* _ASM_SN_SN0_ADDRS_H */ diff --git a/include/asm-mips/sn/sn0/arch.h b/include/asm-mips/sn/sn0/arch.h deleted file mode 100644 index f734f2007f24..000000000000 --- a/include/asm-mips/sn/sn0/arch.h +++ /dev/null @@ -1,72 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * SGI IP27 specific setup. - * - * Copyright (C) 1995 - 1997, 1999 Silcon Graphics, Inc. - * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org) - */ -#ifndef _ASM_SN_SN0_ARCH_H -#define _ASM_SN_SN0_ARCH_H - - -#ifndef SN0XXL /* 128 cpu SMP max */ -/* - * This is the maximum number of nodes that can be part of a kernel. - * Effectively, it's the maximum number of compact node ids (cnodeid_t). - */ -#define MAX_COMPACT_NODES 64 - -/* - * MAXCPUS refers to the maximum number of CPUs in a single kernel. - * This is not necessarily the same as MAXNODES * CPUS_PER_NODE - */ -#define MAXCPUS 128 - -#else /* SN0XXL system */ - -#define MAX_COMPACT_NODES 128 -#define MAXCPUS 256 - -#endif /* SN0XXL */ - -/* - * This is the maximum number of NASIDS that can be present in a system. - * (Highest NASID plus one.) - */ -#define MAX_NASIDS 256 - -/* - * MAX_REGIONS refers to the maximum number of hardware partitioned regions. - */ -#define MAX_REGIONS 64 -#define MAX_NONPREMIUM_REGIONS 16 -#define MAX_PREMIUM_REGIONS MAX_REGIONS - -/* - * MAX_PARITIONS refers to the maximum number of logically defined - * partitions the system can support. - */ -#define MAX_PARTITIONS MAX_REGIONS - -#define NASID_MASK_BYTES ((MAX_NASIDS + 7) / 8) - -/* - * Slot constants for SN0 - */ -#ifdef CONFIG_SGI_SN_N_MODE -#define MAX_MEM_SLOTS 16 /* max slots per node */ -#else /* !CONFIG_SGI_SN_N_MODE, assume CONFIG_SGI_SN_M_MODE */ -#define MAX_MEM_SLOTS 32 /* max slots per node */ -#endif /* CONFIG_SGI_SN_M_MODE */ - -#define SLOT_SHIFT (27) -#define SLOT_MIN_MEM_SIZE (32*1024*1024) - -#define CPUS_PER_NODE 2 /* CPUs on a single hub */ -#define CPUS_PER_NODE_SHFT 1 /* Bits to shift in the node number */ -#define CPUS_PER_SUBNODE 2 /* CPUs on a single hub PI */ - -#endif /* _ASM_SN_SN0_ARCH_H */ diff --git a/include/asm-mips/sn/sn0/hub.h b/include/asm-mips/sn/sn0/hub.h deleted file mode 100644 index 3e228f8e7969..000000000000 --- a/include/asm-mips/sn/sn0/hub.h +++ /dev/null @@ -1,40 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_HUB_H -#define _ASM_SN_SN0_HUB_H - -/* The secret password; used to release protection */ -#define HUB_PASSWORD 0x53474972756c6573ull - -#define CHIPID_HUB 0 -#define CHIPID_ROUTER 1 - -#define HUB_REV_1_0 1 -#define HUB_REV_2_0 2 -#define HUB_REV_2_1 3 -#define HUB_REV_2_2 4 -#define HUB_REV_2_3 5 -#define HUB_REV_2_4 6 - -#define MAX_HUB_PATH 80 - -#include <asm/sn/sn0/addrs.h> -#include <asm/sn/sn0/hubpi.h> -#include <asm/sn/sn0/hubmd.h> -#include <asm/sn/sn0/hubio.h> -#include <asm/sn/sn0/hubni.h> -//#include <asm/sn/sn0/hubcore.h> - -/* Translation of uncached attributes */ -#define UATTR_HSPEC 0 -#define UATTR_IO 1 -#define UATTR_MSPEC 2 -#define UATTR_UNCAC 3 - -#endif /* _ASM_SN_SN0_HUB_H */ diff --git a/include/asm-mips/sn/sn0/hubio.h b/include/asm-mips/sn/sn0/hubio.h deleted file mode 100644 index 0187895e556c..000000000000 --- a/include/asm-mips/sn/sn0/hubio.h +++ /dev/null @@ -1,972 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/hubio.h>, Revision 1.80. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SGI_SN_SN0_HUBIO_H -#define _ASM_SGI_SN_SN0_HUBIO_H - -/* - * Hub I/O interface registers - * - * All registers in this file are subject to change until Hub chip tapeout. - * In general, the longer software name should be used when available. - */ - -/* - * Slightly friendlier names for some common registers. - * The hardware definitions follow. - */ -#define IIO_WIDGET IIO_WID /* Widget identification */ -#define IIO_WIDGET_STAT IIO_WSTAT /* Widget status register */ -#define IIO_WIDGET_CTRL IIO_WCR /* Widget control register */ -#define IIO_WIDGET_TOUT IIO_WRTO /* Widget request timeout */ -#define IIO_WIDGET_FLUSH IIO_WTFR /* Widget target flush */ -#define IIO_PROTECT IIO_ILAPR /* IO interface protection */ -#define IIO_PROTECT_OVRRD IIO_ILAPO /* IO protect override */ -#define IIO_OUTWIDGET_ACCESS IIO_IOWA /* Outbound widget access */ -#define IIO_INWIDGET_ACCESS IIO_IIWA /* Inbound widget access */ -#define IIO_INDEV_ERR_MASK IIO_IIDEM /* Inbound device error mask */ -#define IIO_LLP_CSR IIO_ILCSR /* LLP control and status */ -#define IIO_LLP_LOG IIO_ILLR /* LLP log */ -#define IIO_XTALKCC_TOUT IIO_IXCC /* Xtalk credit count timeout*/ -#define IIO_XTALKTT_TOUT IIO_IXTT /* Xtalk tail timeout */ -#define IIO_IO_ERR_CLR IIO_IECLR /* IO error clear */ -#define IIO_BTE_CRB_CNT IIO_IBCN /* IO BTE CRB count */ - -#define IIO_LLP_CSR_IS_UP 0x00002000 -#define IIO_LLP_CSR_LLP_STAT_MASK 0x00003000 -#define IIO_LLP_CSR_LLP_STAT_SHFT 12 - -/* key to IIO_PROTECT_OVRRD */ -#define IIO_PROTECT_OVRRD_KEY 0x53474972756c6573ull /* "SGIrules" */ - -/* BTE register names */ -#define IIO_BTE_STAT_0 IIO_IBLS_0 /* Also BTE length/status 0 */ -#define IIO_BTE_SRC_0 IIO_IBSA_0 /* Also BTE source address 0 */ -#define IIO_BTE_DEST_0 IIO_IBDA_0 /* Also BTE dest. address 0 */ -#define IIO_BTE_CTRL_0 IIO_IBCT_0 /* Also BTE control/terminate 0 */ -#define IIO_BTE_NOTIFY_0 IIO_IBNA_0 /* Also BTE notification 0 */ -#define IIO_BTE_INT_0 IIO_IBIA_0 /* Also BTE interrupt 0 */ -#define IIO_BTE_OFF_0 0 /* Base offset from BTE 0 regs. */ -#define IIO_BTE_OFF_1 IIO_IBLS_1 - IIO_IBLS_0 /* Offset from base to BTE 1 */ - -/* BTE register offsets from base */ -#define BTEOFF_STAT 0 -#define BTEOFF_SRC (IIO_BTE_SRC_0 - IIO_BTE_STAT_0) -#define BTEOFF_DEST (IIO_BTE_DEST_0 - IIO_BTE_STAT_0) -#define BTEOFF_CTRL (IIO_BTE_CTRL_0 - IIO_BTE_STAT_0) -#define BTEOFF_NOTIFY (IIO_BTE_NOTIFY_0 - IIO_BTE_STAT_0) -#define BTEOFF_INT (IIO_BTE_INT_0 - IIO_BTE_STAT_0) - - -/* - * The following definitions use the names defined in the IO interface - * document for ease of reference. When possible, software should - * generally use the longer but clearer names defined above. - */ - -#define IIO_BASE 0x400000 -#define IIO_BASE_BTE0 0x410000 -#define IIO_BASE_BTE1 0x420000 -#define IIO_BASE_PERF 0x430000 -#define IIO_PERF_CNT 0x430008 - -#define IO_PERF_SETS 32 - -#define IIO_WID 0x400000 /* Widget identification */ -#define IIO_WSTAT 0x400008 /* Widget status */ -#define IIO_WCR 0x400020 /* Widget control */ - -#define IIO_WSTAT_ECRAZY (1ULL << 32) /* Hub gone crazy */ -#define IIO_WSTAT_TXRETRY (1ULL << 9) /* Hub Tx Retry timeout */ -#define IIO_WSTAT_TXRETRY_MASK (0x7F) -#define IIO_WSTAT_TXRETRY_SHFT (16) -#define IIO_WSTAT_TXRETRY_CNT(w) (((w) >> IIO_WSTAT_TXRETRY_SHFT) & \ - IIO_WSTAT_TXRETRY_MASK) - -#define IIO_ILAPR 0x400100 /* Local Access Protection */ -#define IIO_ILAPO 0x400108 /* Protection override */ -#define IIO_IOWA 0x400110 /* outbound widget access */ -#define IIO_IIWA 0x400118 /* inbound widget access */ -#define IIO_IIDEM 0x400120 /* Inbound Device Error Mask */ -#define IIO_ILCSR 0x400128 /* LLP control and status */ -#define IIO_ILLR 0x400130 /* LLP Log */ -#define IIO_IIDSR 0x400138 /* Interrupt destination */ - -#define IIO_IIBUSERR 0x1400208 /* Reads here cause a bus error. */ - -/* IO Interrupt Destination Register */ -#define IIO_IIDSR_SENT_SHIFT 28 -#define IIO_IIDSR_SENT_MASK 0x10000000 -#define IIO_IIDSR_ENB_SHIFT 24 -#define IIO_IIDSR_ENB_MASK 0x01000000 -#define IIO_IIDSR_NODE_SHIFT 8 -#define IIO_IIDSR_NODE_MASK 0x0000ff00 -#define IIO_IIDSR_LVL_SHIFT 0 -#define IIO_IIDSR_LVL_MASK 0x0000003f - - -/* GFX Flow Control Node/Widget Register */ -#define IIO_IGFX_0 0x400140 /* gfx node/widget register 0 */ -#define IIO_IGFX_1 0x400148 /* gfx node/widget register 1 */ -#define IIO_IGFX_W_NUM_BITS 4 /* size of widget num field */ -#define IIO_IGFX_W_NUM_MASK ((1<<IIO_IGFX_W_NUM_BITS)-1) -#define IIO_IGFX_W_NUM_SHIFT 0 -#define IIO_IGFX_N_NUM_BITS 9 /* size of node num field */ -#define IIO_IGFX_N_NUM_MASK ((1<<IIO_IGFX_N_NUM_BITS)-1) -#define IIO_IGFX_N_NUM_SHIFT 4 -#define IIO_IGFX_P_NUM_BITS 1 /* size of processor num field */ -#define IIO_IGFX_P_NUM_MASK ((1<<IIO_IGFX_P_NUM_BITS)-1) -#define IIO_IGFX_P_NUM_SHIFT 16 -#define IIO_IGFX_VLD_BITS 1 /* size of valid field */ -#define IIO_IGFX_VLD_MASK ((1<<IIO_IGFX_VLD_BITS)-1) -#define IIO_IGFX_VLD_SHIFT 20 -#define IIO_IGFX_INIT(widget, node, cpu, valid) (\ - (((widget) & IIO_IGFX_W_NUM_MASK) << IIO_IGFX_W_NUM_SHIFT) | \ - (((node) & IIO_IGFX_N_NUM_MASK) << IIO_IGFX_N_NUM_SHIFT) | \ - (((cpu) & IIO_IGFX_P_NUM_MASK) << IIO_IGFX_P_NUM_SHIFT) | \ - (((valid) & IIO_IGFX_VLD_MASK) << IIO_IGFX_VLD_SHIFT) ) - -/* Scratch registers (not all bits available) */ -#define IIO_SCRATCH_REG0 0x400150 -#define IIO_SCRATCH_REG1 0x400158 -#define IIO_SCRATCH_MASK 0x0000000f00f11fff - -#define IIO_SCRATCH_BIT0_0 0x0000000800000000 -#define IIO_SCRATCH_BIT0_1 0x0000000400000000 -#define IIO_SCRATCH_BIT0_2 0x0000000200000000 -#define IIO_SCRATCH_BIT0_3 0x0000000100000000 -#define IIO_SCRATCH_BIT0_4 0x0000000000800000 -#define IIO_SCRATCH_BIT0_5 0x0000000000400000 -#define IIO_SCRATCH_BIT0_6 0x0000000000200000 -#define IIO_SCRATCH_BIT0_7 0x0000000000100000 -#define IIO_SCRATCH_BIT0_8 0x0000000000010000 -#define IIO_SCRATCH_BIT0_9 0x0000000000001000 -#define IIO_SCRATCH_BIT0_R 0x0000000000000fff - -/* IO Translation Table Entries */ -#define IIO_NUM_ITTES 7 /* ITTEs numbered 0..6 */ - /* Hw manuals number them 1..7! */ - -/* - * As a permanent workaround for a bug in the PI side of the hub, we've - * redefined big window 7 as small window 0. - */ -#define HUB_NUM_BIG_WINDOW IIO_NUM_ITTES - 1 - -/* - * Use the top big window as a surrogate for the first small window - */ -#define SWIN0_BIGWIN HUB_NUM_BIG_WINDOW - -#define ILCSR_WARM_RESET 0x100 -/* - * The IO LLP control status register and widget control register - */ -#ifndef __ASSEMBLY__ - -typedef union hubii_wid_u { - u64 wid_reg_value; - struct { - u64 wid_rsvd: 32, /* unused */ - wid_rev_num: 4, /* revision number */ - wid_part_num: 16, /* the widget type: hub=c101 */ - wid_mfg_num: 11, /* Manufacturer id (IBM) */ - wid_rsvd1: 1; /* Reserved */ - } wid_fields_s; -} hubii_wid_t; - - -typedef union hubii_wcr_u { - u64 wcr_reg_value; - struct { - u64 wcr_rsvd: 41, /* unused */ - wcr_e_thresh: 5, /* elasticity threshold */ - wcr_dir_con: 1, /* widget direct connect */ - wcr_f_bad_pkt: 1, /* Force bad llp pkt enable */ - wcr_xbar_crd: 3, /* LLP crossbar credit */ - wcr_rsvd1: 8, /* Reserved */ - wcr_tag_mode: 1, /* Tag mode */ - wcr_widget_id: 4; /* LLP crossbar credit */ - } wcr_fields_s; -} hubii_wcr_t; - -#define iwcr_dir_con wcr_fields_s.wcr_dir_con - -typedef union hubii_wstat_u { - u64 reg_value; - struct { - u64 rsvd1: 31, - crazy: 1, /* Crazy bit */ - rsvd2: 8, - llp_tx_cnt: 8, /* LLP Xmit retry counter */ - rsvd3: 6, - tx_max_rtry: 1, /* LLP Retry Timeout Signal */ - rsvd4: 2, - xt_tail_to: 1, /* Xtalk Tail Timeout */ - xt_crd_to: 1, /* Xtalk Credit Timeout */ - pending: 4; /* Pending Requests */ - } wstat_fields_s; -} hubii_wstat_t; - - -typedef union hubii_ilcsr_u { - u64 icsr_reg_value; - struct { - u64 icsr_rsvd: 22, /* unused */ - icsr_max_burst: 10, /* max burst */ - icsr_rsvd4: 6, /* reserved */ - icsr_max_retry: 10, /* max retry */ - icsr_rsvd3: 2, /* reserved */ - icsr_lnk_stat: 2, /* link status */ - icsr_bm8: 1, /* Bit mode 8 */ - icsr_llp_en: 1, /* LLP enable bit */ - icsr_rsvd2: 1, /* reserver */ - icsr_wrm_reset: 1, /* Warm reset bit */ - icsr_rsvd1: 2, /* Data ready offset */ - icsr_null_to: 6; /* Null timeout */ - - } icsr_fields_s; -} hubii_ilcsr_t; - - -typedef union hubii_iowa_u { - u64 iowa_reg_value; - struct { - u64 iowa_rsvd: 48, /* unused */ - iowa_wxoac: 8, /* xtalk widget access bits */ - iowa_rsvd1: 7, /* xtalk widget access bits */ - iowa_w0oac: 1; /* xtalk widget access bits */ - } iowa_fields_s; -} hubii_iowa_t; - -typedef union hubii_iiwa_u { - u64 iiwa_reg_value; - struct { - u64 iiwa_rsvd: 48, /* unused */ - iiwa_wxiac: 8, /* hub wid access bits */ - iiwa_rsvd1: 7, /* reserved */ - iiwa_w0iac: 1; /* hub wid0 access */ - } iiwa_fields_s; -} hubii_iiwa_t; - -typedef union hubii_illr_u { - u64 illr_reg_value; - struct { - u64 illr_rsvd: 32, /* unused */ - illr_cb_cnt: 16, /* checkbit error count */ - illr_sn_cnt: 16; /* sequence number count */ - } illr_fields_s; -} hubii_illr_t; - -/* The structures below are defined to extract and modify the ii -performance registers */ - -/* io_perf_sel allows the caller to specify what tests will be - performed */ -typedef union io_perf_sel { - u64 perf_sel_reg; - struct { - u64 perf_rsvd : 48, - perf_icct : 8, - perf_ippr1 : 4, - perf_ippr0 : 4; - } perf_sel_bits; -} io_perf_sel_t; - -/* io_perf_cnt is to extract the count from the hub registers. Due to - hardware problems there is only one counter, not two. */ - -typedef union io_perf_cnt { - u64 perf_cnt; - struct { - u64 perf_rsvd1 : 32, - perf_rsvd2 : 12, - perf_cnt : 20; - } perf_cnt_bits; -} io_perf_cnt_t; - -#endif /* !__ASSEMBLY__ */ - - -#define LNK_STAT_WORKING 0x2 - -#define IIO_LLP_CB_MAX 0xffff -#define IIO_LLP_SN_MAX 0xffff - -/* IO PRB Entries */ -#define IIO_NUM_IPRBS (9) -#define IIO_IOPRB_0 0x400198 /* PRB entry 0 */ -#define IIO_IOPRB_8 0x4001a0 /* PRB entry 8 */ -#define IIO_IOPRB_9 0x4001a8 /* PRB entry 9 */ -#define IIO_IOPRB_A 0x4001b0 /* PRB entry a */ -#define IIO_IOPRB_B 0x4001b8 /* PRB entry b */ -#define IIO_IOPRB_C 0x4001c0 /* PRB entry c */ -#define IIO_IOPRB_D 0x4001c8 /* PRB entry d */ -#define IIO_IOPRB_E 0x4001d0 /* PRB entry e */ -#define IIO_IOPRB_F 0x4001d8 /* PRB entry f */ - - -#define IIO_IXCC 0x4001e0 /* Crosstalk credit count timeout */ -#define IIO_IXTCC IIO_IXCC -#define IIO_IMEM 0x4001e8 /* Miscellaneous Enable Mask */ -#define IIO_IXTT 0x4001f0 /* Crosstalk tail timeout */ -#define IIO_IECLR 0x4001f8 /* IO error clear */ -#define IIO_IBCN 0x400200 /* IO BTE CRB count */ - -/* - * IIO_IMEM Register fields. - */ -#define IIO_IMEM_W0ESD 0x1 /* Widget 0 shut down due to error */ -#define IIO_IMEM_B0ESD (1 << 4) /* BTE 0 shut down due to error */ -#define IIO_IMEM_B1ESD (1 << 8) /* BTE 1 Shut down due to error */ - -/* PIO Read address Table Entries */ -#define IIO_IPCA 0x400300 /* PRB Counter adjust */ -#define IIO_NUM_PRTES 8 /* Total number of PRB table entries */ -#define IIO_PRTE_0 0x400308 /* PIO Read address table entry 0 */ -#define IIO_PRTE(_x) (IIO_PRTE_0 + (8 * (_x))) -#define IIO_WIDPRTE(x) IIO_PRTE(((x) - 8)) /* widget ID to its PRTE num */ -#define IIO_IPDR 0x400388 /* PIO table entry deallocation */ -#define IIO_ICDR 0x400390 /* CRB Entry Deallocation */ -#define IIO_IFDR 0x400398 /* IOQ FIFO Depth */ -#define IIO_IIAP 0x4003a0 /* IIQ Arbitration Parameters */ -#define IIO_IMMR IIO_IIAP -#define IIO_ICMR 0x4003a8 /* CRB Management Register */ -#define IIO_ICCR 0x4003b0 /* CRB Control Register */ -#define IIO_ICTO 0x4003b8 /* CRB Time Out Register */ -#define IIO_ICTP 0x4003c0 /* CRB Time Out Prescalar */ - - -/* - * ICMR register fields - */ -#define IIO_ICMR_PC_VLD_SHFT 36 -#define IIO_ICMR_PC_VLD_MASK (0x7fffUL << IIO_ICMR_PC_VLD_SHFT) - -#define IIO_ICMR_CRB_VLD_SHFT 20 -#define IIO_ICMR_CRB_VLD_MASK (0x7fffUL << IIO_ICMR_CRB_VLD_SHFT) - -#define IIO_ICMR_FC_CNT_SHFT 16 -#define IIO_ICMR_FC_CNT_MASK (0xf << IIO_ICMR_FC_CNT_SHFT) - -#define IIO_ICMR_C_CNT_SHFT 4 -#define IIO_ICMR_C_CNT_MASK (0xf << IIO_ICMR_C_CNT_SHFT) - -#define IIO_ICMR_P_CNT_SHFT 0 -#define IIO_ICMR_P_CNT_MASK (0xf << IIO_ICMR_P_CNT_SHFT) - -#define IIO_ICMR_PRECISE (1UL << 52) -#define IIO_ICMR_CLR_RPPD (1UL << 13) -#define IIO_ICMR_CLR_RQPD (1UL << 12) - -/* - * IIO PIO Deallocation register field masks : (IIO_IPDR) - */ -#define IIO_IPDR_PND (1 << 4) - -/* - * IIO CRB deallocation register field masks: (IIO_ICDR) - */ -#define IIO_ICDR_PND (1 << 4) - -/* - * IIO CRB control register Fields: IIO_ICCR - */ -#define IIO_ICCR_PENDING (0x10000) -#define IIO_ICCR_CMD_MASK (0xFF) -#define IIO_ICCR_CMD_SHFT (7) -#define IIO_ICCR_CMD_NOP (0x0) /* No Op */ -#define IIO_ICCR_CMD_WAKE (0x100) /* Reactivate CRB entry and process */ -#define IIO_ICCR_CMD_TIMEOUT (0x200) /* Make CRB timeout & mark invalid */ -#define IIO_ICCR_CMD_EJECT (0x400) /* Contents of entry written to memory - * via a WB - */ -#define IIO_ICCR_CMD_FLUSH (0x800) - -/* - * CRB manipulation macros - * The CRB macros are slightly complicated, since there are up to - * four registers associated with each CRB entry. - */ -#define IIO_NUM_CRBS 15 /* Number of CRBs */ -#define IIO_NUM_NORMAL_CRBS 12 /* Number of regular CRB entries */ -#define IIO_NUM_PC_CRBS 4 /* Number of partial cache CRBs */ -#define IIO_ICRB_OFFSET 8 -#define IIO_ICRB_0 0x400400 -/* XXX - This is now tuneable: - #define IIO_FIRST_PC_ENTRY 12 - */ - -#define IIO_ICRB_A(_x) (IIO_ICRB_0 + (4 * IIO_ICRB_OFFSET * (_x))) -#define IIO_ICRB_B(_x) (IIO_ICRB_A(_x) + 1*IIO_ICRB_OFFSET) -#define IIO_ICRB_C(_x) (IIO_ICRB_A(_x) + 2*IIO_ICRB_OFFSET) -#define IIO_ICRB_D(_x) (IIO_ICRB_A(_x) + 3*IIO_ICRB_OFFSET) - -/* XXX - IBUE register coming for Hub 2 */ - -/* - * - * CRB Register description. - * - * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING - * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING - * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING - * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING - * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING - * - * Many of the fields in CRB are status bits used by hardware - * for implementation of the protocol. It's very dangerous to - * mess around with the CRB registers. - * - * It's OK to read the CRB registers and try to make sense out of the - * fields in CRB. - * - * Updating CRB requires all activities in Hub IIO to be quiesced. - * otherwise, a write to CRB could corrupt other CRB entries. - * CRBs are here only as a back door peek to hub IIO's status. - * Quiescing implies no dmas no PIOs - * either directly from the cpu or from sn0net. - * this is not something that can be done easily. So, AVOID updating - * CRBs. - */ - -/* - * Fields in CRB Register A - */ -#ifndef __ASSEMBLY__ -typedef union icrba_u { - u64 reg_value; - struct { - u64 resvd: 6, - stall_bte0: 1, /* Stall BTE 0 */ - stall_bte1: 1, /* Stall BTE 1 */ - error: 1, /* CRB has an error */ - ecode: 3, /* Error Code */ - lnetuce: 1, /* SN0net Uncorrectable error */ - mark: 1, /* CRB Has been marked */ - xerr: 1, /* Error bit set in xtalk header */ - sidn: 4, /* SIDN field from xtalk */ - tnum: 5, /* TNUM field in xtalk */ - addr: 38, /* Address of request */ - valid: 1, /* Valid status */ - iow: 1; /* IO Write operation */ - } icrba_fields_s; -} icrba_t; - -/* This is an alternate typedef for the HUB1 CRB A in order to allow - runtime selection of the format based on the REV_ID field of the - NI_STATUS_REV_ID register. */ -typedef union h1_icrba_u { - u64 reg_value; - - struct { - u64 resvd: 6, - unused: 1, /* Unused but RW!! */ - error: 1, /* CRB has an error */ - ecode: 4, /* Error Code */ - lnetuce: 1, /* SN0net Uncorrectable error */ - mark: 1, /* CRB Has been marked */ - xerr: 1, /* Error bit set in xtalk header */ - sidn: 4, /* SIDN field from xtalk */ - tnum: 5, /* TNUM field in xtalk */ - addr: 38, /* Address of request */ - valid: 1, /* Valid status */ - iow: 1; /* IO Write operation */ - } h1_icrba_fields_s; -} h1_icrba_t; - -/* XXX - Is this still right? Check the spec. */ -#define ICRBN_A_CERR_SHFT 54 -#define ICRBN_A_ERR_MASK 0x3ff - -#endif /* !__ASSEMBLY__ */ - -#define IIO_ICRB_ADDR_SHFT 2 /* Shift to get proper address */ - -/* - * values for "ecode" field - */ -#define IIO_ICRB_ECODE_DERR 0 /* Directory error due to IIO access */ -#define IIO_ICRB_ECODE_PERR 1 /* Poison error on IO access */ -#define IIO_ICRB_ECODE_WERR 2 /* Write error by IIO access - * e.g. WINV to a Read only line. - */ -#define IIO_ICRB_ECODE_AERR 3 /* Access error caused by IIO access */ -#define IIO_ICRB_ECODE_PWERR 4 /* Error on partial write */ -#define IIO_ICRB_ECODE_PRERR 5 /* Error on partial read */ -#define IIO_ICRB_ECODE_TOUT 6 /* CRB timeout before deallocating */ -#define IIO_ICRB_ECODE_XTERR 7 /* Incoming xtalk pkt had error bit */ - - - -/* - * Fields in CRB Register B - */ -#ifndef __ASSEMBLY__ -typedef union icrbb_u { - u64 reg_value; - struct { - u64 rsvd1: 5, - btenum: 1, /* BTE to which entry belongs to */ - cohtrans: 1, /* Coherent transaction */ - xtsize: 2, /* Xtalk operation size - * 0: Double Word - * 1: 32 Bytes. - * 2: 128 Bytes, - * 3: Reserved. - */ - srcnode: 9, /* Source Node ID */ - srcinit: 2, /* Source Initiator: - * See below for field values. - */ - useold: 1, /* Use OLD command for processing */ - imsgtype: 2, /* Incoming message type - * see below for field values - */ - imsg: 8, /* Incoming message */ - initator: 3, /* Initiator of original request - * See below for field values. - */ - reqtype: 5, /* Identifies type of request - * See below for field values. - */ - rsvd2: 7, - ackcnt: 11, /* Invalidate ack count */ - resp: 1, /* data response given to processor */ - ack: 1, /* indicates data ack received */ - hold: 1, /* entry is gathering inval acks */ - wb_pend:1, /* waiting for writeback to complete */ - intvn: 1, /* Intervention */ - stall_ib: 1, /* Stall Ibuf (from crosstalk) */ - stall_intr: 1; /* Stall internal interrupts */ - } icrbb_field_s; -} icrbb_t; - -/* This is an alternate typedef for the HUB1 CRB B in order to allow - runtime selection of the format based on the REV_ID field of the - NI_STATUS_REV_ID register. */ -typedef union h1_icrbb_u { - u64 reg_value; - struct { - u64 rsvd1: 5, - btenum: 1, /* BTE to which entry belongs to */ - cohtrans: 1, /* Coherent transaction */ - xtsize: 2, /* Xtalk operation size - * 0: Double Word - * 1: 32 Bytes. - * 2: 128 Bytes, - * 3: Reserved. - */ - srcnode: 9, /* Source Node ID */ - srcinit: 2, /* Source Initiator: - * See below for field values. - */ - useold: 1, /* Use OLD command for processing */ - imsgtype: 2, /* Incoming message type - * see below for field values - */ - imsg: 8, /* Incoming message */ - initator: 3, /* Initiator of original request - * See below for field values. - */ - rsvd2: 1, - pcache: 1, /* entry belongs to partial cache */ - reqtype: 5, /* Identifies type of request - * See below for field values. - */ - stl_ib: 1, /* stall Ibus coming from xtalk */ - stl_intr: 1, /* Stall internal interrupts */ - stl_bte0: 1, /* Stall BTE 0 */ - stl_bte1: 1, /* Stall BTE 1 */ - intrvn: 1, /* Req was target of intervention */ - ackcnt: 11, /* Invalidate ack count */ - resp: 1, /* data response given to processor */ - ack: 1, /* indicates data ack received */ - hold: 1, /* entry is gathering inval acks */ - wb_pend:1, /* waiting for writeback to complete */ - sleep: 1, /* xtalk req sleeping till IO-sync */ - pnd_reply: 1, /* replies not issed due to IOQ full */ - pnd_req: 1; /* reqs not issued due to IOQ full */ - } h1_icrbb_field_s; -} h1_icrbb_t; - - -#define b_imsgtype icrbb_field_s.imsgtype -#define b_btenum icrbb_field_s.btenum -#define b_cohtrans icrbb_field_s.cohtrans -#define b_xtsize icrbb_field_s.xtsize -#define b_srcnode icrbb_field_s.srcnode -#define b_srcinit icrbb_field_s.srcinit -#define b_imsgtype icrbb_field_s.imsgtype -#define b_imsg icrbb_field_s.imsg -#define b_initiator icrbb_field_s.initiator - -#endif /* !__ASSEMBLY__ */ - -/* - * values for field xtsize - */ -#define IIO_ICRB_XTSIZE_DW 0 /* Xtalk operation size is 8 bytes */ -#define IIO_ICRB_XTSIZE_32 1 /* Xtalk operation size is 32 bytes */ -#define IIO_ICRB_XTSIZE_128 2 /* Xtalk operation size is 128 bytes */ - -/* - * values for field srcinit - */ -#define IIO_ICRB_PROC0 0 /* Source of request is Proc 0 */ -#define IIO_ICRB_PROC1 1 /* Source of request is Proc 1 */ -#define IIO_ICRB_GB_REQ 2 /* Source is Guranteed BW request */ -#define IIO_ICRB_IO_REQ 3 /* Source is Normal IO request */ - -/* - * Values for field imsgtype - */ -#define IIO_ICRB_IMSGT_XTALK 0 /* Incoming Meessage from Xtalk */ -#define IIO_ICRB_IMSGT_BTE 1 /* Incoming message from BTE */ -#define IIO_ICRB_IMSGT_SN0NET 2 /* Incoming message from SN0 net */ -#define IIO_ICRB_IMSGT_CRB 3 /* Incoming message from CRB ??? */ - -/* - * values for field initiator. - */ -#define IIO_ICRB_INIT_XTALK 0 /* Message originated in xtalk */ -#define IIO_ICRB_INIT_BTE0 0x1 /* Message originated in BTE 0 */ -#define IIO_ICRB_INIT_SN0NET 0x2 /* Message originated in SN0net */ -#define IIO_ICRB_INIT_CRB 0x3 /* Message originated in CRB ? */ -#define IIO_ICRB_INIT_BTE1 0x5 /* MEssage originated in BTE 1 */ - -/* - * Values for field reqtype. - */ -/* XXX - Need to fix this for Hub 2 */ -#define IIO_ICRB_REQ_DWRD 0 /* Request type double word */ -#define IIO_ICRB_REQ_QCLRD 1 /* Request is Qrtr Caceh line Rd */ -#define IIO_ICRB_REQ_BLKRD 2 /* Request is block read */ -#define IIO_ICRB_REQ_RSHU 6 /* Request is BTE block read */ -#define IIO_ICRB_REQ_REXU 7 /* request is BTE Excl Read */ -#define IIO_ICRB_REQ_RDEX 8 /* Request is Read Exclusive */ -#define IIO_ICRB_REQ_WINC 9 /* Request is Write Invalidate */ -#define IIO_ICRB_REQ_BWINV 10 /* Request is BTE Winv */ -#define IIO_ICRB_REQ_PIORD 11 /* Request is PIO read */ -#define IIO_ICRB_REQ_PIOWR 12 /* Request is PIO Write */ -#define IIO_ICRB_REQ_PRDM 13 /* Request is Fetch&Op */ -#define IIO_ICRB_REQ_PWRM 14 /* Request is Store &Op */ -#define IIO_ICRB_REQ_PTPWR 15 /* Request is Peer to peer */ -#define IIO_ICRB_REQ_WB 16 /* Request is Write back */ -#define IIO_ICRB_REQ_DEX 17 /* Retained DEX Cache line */ - -/* - * Fields in CRB Register C - */ - -#ifndef __ASSEMBLY__ - -typedef union icrbc_s { - u64 reg_value; - struct { - u64 rsvd: 6, - sleep: 1, - pricnt: 4, /* Priority count sent with Read req */ - pripsc: 4, /* Priority Pre scalar */ - bteop: 1, /* BTE Operation */ - push_be: 34, /* Push address Byte enable - * Holds push addr, if CRB is for BTE - * If CRB belongs to Partial cache, - * this contains byte enables bits - * ([47:46] = 0) - */ - suppl: 11, /* Supplemental field */ - barrop: 1, /* Barrier Op bit set in xtalk req */ - doresp: 1, /* Xtalk req needs a response */ - gbr: 1; /* GBR bit set in xtalk packet */ - } icrbc_field_s; -} icrbc_t; - -#define c_pricnt icrbc_field_s.pricnt -#define c_pripsc icrbc_field_s.pripsc -#define c_bteop icrbc_field_s.bteop -#define c_bteaddr icrbc_field_s.push_be /* push_be field has 2 names */ -#define c_benable icrbc_field_s.push_be /* push_be field has 2 names */ -#define c_suppl icrbc_field_s.suppl -#define c_barrop icrbc_field_s.barrop -#define c_doresp icrbc_field_s.doresp -#define c_gbr icrbc_field_s.gbr -#endif /* !__ASSEMBLY__ */ - -/* - * Fields in CRB Register D - */ - -#ifndef __ASSEMBLY__ -typedef union icrbd_s { - u64 reg_value; - struct { - u64 rsvd: 38, - toutvld: 1, /* Timeout in progress for this CRB */ - ctxtvld: 1, /* Context field below is valid */ - rsvd2: 1, - context: 15, /* Bit vector: - * Has a bit set for each CRB entry - * which needs to be deallocated - * before this CRB entry is processed. - * Set only for barrier operations. - */ - timeout: 8; /* Timeout Upper 8 bits */ - } icrbd_field_s; -} icrbd_t; - -#define icrbd_toutvld icrbd_field_s.toutvld -#define icrbd_ctxtvld icrbd_field_s.ctxtvld -#define icrbd_context icrbd_field_s.context - - -typedef union hubii_ifdr_u { - u64 hi_ifdr_value; - struct { - u64 ifdr_rsvd: 49, - ifdr_maxrp: 7, - ifdr_rsvd1: 1, - ifdr_maxrq: 7; - } hi_ifdr_fields; -} hubii_ifdr_t; - -#endif /* !__ASSEMBLY__ */ - -/* - * Hardware designed names for the BTE control registers. - */ -#define IIO_IBLS_0 0x410000 /* BTE length/status 0 */ -#define IIO_IBSA_0 0x410008 /* BTE source address 0 */ -#define IIO_IBDA_0 0x410010 /* BTE destination address 0 */ -#define IIO_IBCT_0 0x410018 /* BTE control/terminate 0 */ -#define IIO_IBNA_0 0x410020 /* BTE notification address 0 */ -#define IIO_IBNR_0 IIO_IBNA_0 -#define IIO_IBIA_0 0x410028 /* BTE interrupt address 0 */ - -#define IIO_IBLS_1 0x420000 /* BTE length/status 1 */ -#define IIO_IBSA_1 0x420008 /* BTE source address 1 */ -#define IIO_IBDA_1 0x420010 /* BTE destination address 1 */ -#define IIO_IBCT_1 0x420018 /* BTE control/terminate 1 */ -#define IIO_IBNA_1 0x420020 /* BTE notification address 1 */ -#define IIO_IBNR_1 IIO_IBNA_1 -#define IIO_IBIA_1 0x420028 /* BTE interrupt address 1 */ - -/* - * More miscellaneous registers - */ -#define IIO_IPCR 0x430000 /* Performance Control */ -#define IIO_IPPR 0x430008 /* Performance Profiling */ - -/* - * IO Error Clear register bit field definitions - */ -#define IECLR_BTE1 (1 << 18) /* clear bte error 1 ??? */ -#define IECLR_BTE0 (1 << 17) /* clear bte error 0 ??? */ -#define IECLR_CRAZY (1 << 16) /* clear crazy bit in wstat reg */ -#define IECLR_PRB_F (1 << 15) /* clear err bit in PRB_F reg */ -#define IECLR_PRB_E (1 << 14) /* clear err bit in PRB_E reg */ -#define IECLR_PRB_D (1 << 13) /* clear err bit in PRB_D reg */ -#define IECLR_PRB_C (1 << 12) /* clear err bit in PRB_C reg */ -#define IECLR_PRB_B (1 << 11) /* clear err bit in PRB_B reg */ -#define IECLR_PRB_A (1 << 10) /* clear err bit in PRB_A reg */ -#define IECLR_PRB_9 (1 << 9) /* clear err bit in PRB_9 reg */ -#define IECLR_PRB_8 (1 << 8) /* clear err bit in PRB_8 reg */ -#define IECLR_PRB_0 (1 << 0) /* clear err bit in PRB_0 reg */ - -/* - * IO PIO Read Table Entry format - */ - -#ifndef __ASSEMBLY__ - -typedef union iprte_a { - u64 entry; - struct { - u64 rsvd1 : 7, /* Reserved field */ - valid : 1, /* Maps to a timeout entry */ - rsvd2 : 1, - srcnode : 9, /* Node which did this PIO */ - initiator : 2, /* If T5A or T5B or IO */ - rsvd3 : 3, - addr : 38, /* Physical address of PIO */ - rsvd4 : 3; - } iprte_fields; -} iprte_a_t; - -#define iprte_valid iprte_fields.valid -#define iprte_timeout iprte_fields.timeout -#define iprte_srcnode iprte_fields.srcnode -#define iprte_init iprte_fields.initiator -#define iprte_addr iprte_fields.addr - -#endif /* !__ASSEMBLY__ */ - -#define IPRTE_ADDRSHFT 3 - -/* - * Hub IIO PRB Register format. - */ - -#ifndef __ASSEMBLY__ -/* - * Note: Fields bnakctr, anakctr, xtalkctrmode, ovflow fields are - * "Status" fields, and should only be used in case of clean up after errors. - */ - -typedef union iprb_u { - u64 reg_value; - struct { - u64 rsvd1: 15, - error: 1, /* Widget rcvd wr resp pkt w/ error */ - ovflow: 5, /* Over flow count. perf measurement */ - fire_and_forget: 1, /* Launch Write without response */ - mode: 2, /* Widget operation Mode */ - rsvd2: 2, - bnakctr: 14, - rsvd3: 2, - anakctr: 14, - xtalkctr: 8; - } iprb_fields_s; -} iprb_t; - -#define iprb_regval reg_value - -#define iprb_error iprb_fields_s.error -#define iprb_ovflow iprb_fields_s.ovflow -#define iprb_ff iprb_fields_s.fire_and_forget -#define iprb_mode iprb_fields_s.mode -#define iprb_bnakctr iprb_fields_s.bnakctr -#define iprb_anakctr iprb_fields_s.anakctr -#define iprb_xtalkctr iprb_fields_s.xtalkctr - -#endif /* !__ASSEMBLY__ */ - -/* - * values for mode field in iprb_t. - * For details of the meanings of NAK and Accept, refer the PIO flow - * document - */ -#define IPRB_MODE_NORMAL (0) -#define IPRB_MODE_COLLECT_A (1) /* PRB in collect A mode */ -#define IPRB_MODE_SERVICE_A (2) /* NAK B and Accept A */ -#define IPRB_MODE_SERVICE_B (3) /* NAK A and Accept B */ - -/* - * IO CRB entry C_A to E_A : Partial (cache) CRBS - */ -#ifndef __ASSEMBLY__ -typedef union icrbp_a { - u64 ip_reg; /* the entire register value */ - struct { - u64 error: 1, /* 63, error occurred */ - ln_uce: 1, /* 62: uncorrectable memory */ - ln_ae: 1, /* 61: protection violation */ - ln_werr:1, /* 60: write access error */ - ln_aerr:1, /* 59: sn0net: Address error */ - ln_perr:1, /* 58: sn0net: poison error */ - timeout:1, /* 57: CRB timed out */ - l_bdpkt:1, /* 56: truncated pkt on sn0net */ - c_bdpkt:1, /* 55: truncated pkt on xtalk */ - c_err: 1, /* 54: incoming xtalk req, err set*/ - rsvd1: 12, /* 53-42: reserved */ - valid: 1, /* 41: Valid status */ - sidn: 4, /* 40-37: SIDN field of xtalk rqst */ - tnum: 5, /* 36-32: TNUM of xtalk request */ - bo: 1, /* 31: barrier op set in xtalk rqst*/ - resprqd:1, /* 30: xtalk rqst requires response*/ - gbr: 1, /* 29: gbr bit set in xtalk rqst */ - size: 2, /* 28-27: size of xtalk request */ - excl: 4, /* 26-23: exclusive bit(s) */ - stall: 3, /* 22-20: stall (xtalk, bte 0/1) */ - intvn: 1, /* 19: rqst target of intervention*/ - resp: 1, /* 18: Data response given to t5 */ - ack: 1, /* 17: Data ack received. */ - hold: 1, /* 16: crb gathering invalidate acks*/ - wb: 1, /* 15: writeback pending. */ - ack_cnt:11, /* 14-04: counter of invalidate acks*/ - tscaler:4; /* 03-00: Timeout prescaler */ - } ip_fmt; -} icrbp_a_t; - -#endif /* !__ASSEMBLY__ */ - -/* - * A couple of defines to go with the above structure. - */ -#define ICRBP_A_CERR_SHFT 54 -#define ICRBP_A_ERR_MASK 0x3ff - -#ifndef __ASSEMBLY__ -typedef union hubii_idsr { - u64 iin_reg; - struct { - u64 rsvd1 : 35, - isent : 1, - rsvd2 : 3, - ienable: 1, - rsvd : 7, - node : 9, - rsvd4 : 1, - level : 7; - } iin_fmt; -} hubii_idsr_t; -#endif /* !__ASSEMBLY__ */ - -/* - * IO BTE Length/Status (IIO_IBLS) register bit field definitions - */ -#define IBLS_BUSY (0x1 << 20) -#define IBLS_ERROR_SHFT 16 -#define IBLS_ERROR (0x1 << IBLS_ERROR_SHFT) -#define IBLS_LENGTH_MASK 0xffff - -/* - * IO BTE Control/Terminate register (IBCT) register bit field definitions - */ -#define IBCT_POISON (0x1 << 8) -#define IBCT_NOTIFY (0x1 << 4) -#define IBCT_ZFIL_MODE (0x1 << 0) - -/* - * IO BTE Interrupt Address Register (IBIA) register bit field definitions - */ -#define IBIA_LEVEL_SHFT 16 -#define IBIA_LEVEL_MASK (0x7f << IBIA_LEVEL_SHFT) -#define IBIA_NODE_ID_SHFT 0 -#define IBIA_NODE_ID_MASK (0x1ff) - -/* - * Miscellaneous hub constants - */ - -/* Number of widgets supported by hub */ -#define HUB_NUM_WIDGET 9 -#define HUB_WIDGET_ID_MIN 0x8 -#define HUB_WIDGET_ID_MAX 0xf - -#define HUB_WIDGET_PART_NUM 0xc101 -#define MAX_HUBS_PER_XBOW 2 - -/* - * Get a hub's widget id from widget control register - */ -#define IIO_WCR_WID_GET(nasid) (REMOTE_HUB_L(nasid, III_WCR) & 0xf) -#define IIO_WST_ERROR_MASK (UINT64_CAST 1 << 32) /* Widget status error */ - -/* - * Number of credits Hub widget has while sending req/response to - * xbow. - * Value of 3 is required by Xbow 1.1 - * We may be able to increase this to 4 with Xbow 1.2. - */ -#define HUBII_XBOW_CREDIT 3 -#define HUBII_XBOW_REV2_CREDIT 4 - -#endif /* _ASM_SGI_SN_SN0_HUBIO_H */ diff --git a/include/asm-mips/sn/sn0/hubmd.h b/include/asm-mips/sn/sn0/hubmd.h deleted file mode 100644 index 14c225d80664..000000000000 --- a/include/asm-mips/sn/sn0/hubmd.h +++ /dev/null @@ -1,789 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/hubmd.h>, revision 1.59. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_HUBMD_H -#define _ASM_SN_SN0_HUBMD_H - - -/* - * Hub Memory/Directory interface registers - */ -#define CACHE_SLINE_SIZE 128 /* Secondary cache line size on SN0 */ - -#define MAX_REGIONS 64 - -/* Hardware page size and shift */ - -#define MD_PAGE_SIZE 4096 /* Page size in bytes */ -#define MD_PAGE_NUM_SHFT 12 /* Address to page number shift */ - -/* Register offsets from LOCAL_HUB or REMOTE_HUB */ - -#define MD_BASE 0x200000 -#define MD_BASE_PERF 0x210000 -#define MD_BASE_JUNK 0x220000 - -#define MD_IO_PROTECT 0x200000 /* MD and core register protection */ -#define MD_IO_PROT_OVRRD 0x200008 /* Clear my bit in MD_IO_PROTECT */ -#define MD_HSPEC_PROTECT 0x200010 /* BDDIR, LBOOT, RBOOT protection */ -#define MD_MEMORY_CONFIG 0x200018 /* Memory/Directory DIMM control */ -#define MD_REFRESH_CONTROL 0x200020 /* Memory/Directory refresh ctrl */ -#define MD_FANDOP_CAC_STAT 0x200028 /* Fetch-and-op cache status */ -#define MD_MIG_DIFF_THRESH 0x200030 /* Page migr. count diff thresh. */ -#define MD_MIG_VALUE_THRESH 0x200038 /* Page migr. count abs. thresh. */ -#define MD_MIG_CANDIDATE 0x200040 /* Latest page migration candidate */ -#define MD_MIG_CANDIDATE_CLR 0x200048 /* Clear page migration candidate */ -#define MD_DIR_ERROR 0x200050 /* Directory DIMM error */ -#define MD_DIR_ERROR_CLR 0x200058 /* Directory DIMM error clear */ -#define MD_PROTOCOL_ERROR 0x200060 /* Directory protocol error */ -#define MD_PROTOCOL_ERROR_CLR 0x200068 /* Directory protocol error clear */ -#define MD_MEM_ERROR 0x200070 /* Memory DIMM error */ -#define MD_MEM_ERROR_CLR 0x200078 /* Memory DIMM error clear */ -#define MD_MISC_ERROR 0x200080 /* Miscellaneous MD error */ -#define MD_MISC_ERROR_CLR 0x200088 /* Miscellaneous MD error clear */ -#define MD_MEM_DIMM_INIT 0x200090 /* Memory DIMM mode initization. */ -#define MD_DIR_DIMM_INIT 0x200098 /* Directory DIMM mode init. */ -#define MD_MOQ_SIZE 0x2000a0 /* MD outgoing queue size */ -#define MD_MLAN_CTL 0x2000a8 /* NIC (Microlan) control register */ - -#define MD_PERF_SEL 0x210000 /* Select perf monitor events */ -#define MD_PERF_CNT0 0x210010 /* Performance counter 0 */ -#define MD_PERF_CNT1 0x210018 /* Performance counter 1 */ -#define MD_PERF_CNT2 0x210020 /* Performance counter 2 */ -#define MD_PERF_CNT3 0x210028 /* Performance counter 3 */ -#define MD_PERF_CNT4 0x210030 /* Performance counter 4 */ -#define MD_PERF_CNT5 0x210038 /* Performance counter 5 */ - -#define MD_UREG0_0 0x220000 /* uController/UART 0 register */ -#define MD_UREG0_1 0x220008 /* uController/UART 0 register */ -#define MD_UREG0_2 0x220010 /* uController/UART 0 register */ -#define MD_UREG0_3 0x220018 /* uController/UART 0 register */ -#define MD_UREG0_4 0x220020 /* uController/UART 0 register */ -#define MD_UREG0_5 0x220028 /* uController/UART 0 register */ -#define MD_UREG0_6 0x220030 /* uController/UART 0 register */ -#define MD_UREG0_7 0x220038 /* uController/UART 0 register */ - -#define MD_SLOTID_USTAT 0x220048 /* Hub slot ID & UART/uCtlr status */ -#define MD_LED0 0x220050 /* Eight-bit LED for CPU A */ -#define MD_LED1 0x220058 /* Eight-bit LED for CPU B */ - -#define MD_UREG1_0 0x220080 /* uController/UART 1 register */ -#define MD_UREG1_1 0x220088 /* uController/UART 1 register */ -#define MD_UREG1_2 0x220090 /* uController/UART 1 register */ -#define MD_UREG1_3 0x220098 /* uController/UART 1 register */ -#define MD_UREG1_4 0x2200a0 /* uController/UART 1 register */ -#define MD_UREG1_5 0x2200a8 /* uController/UART 1 register */ -#define MD_UREG1_6 0x2200b0 /* uController/UART 1 register */ -#define MD_UREG1_7 0x2200b8 /* uController/UART 1 register */ -#define MD_UREG1_8 0x2200c0 /* uController/UART 1 register */ -#define MD_UREG1_9 0x2200c8 /* uController/UART 1 register */ -#define MD_UREG1_10 0x2200d0 /* uController/UART 1 register */ -#define MD_UREG1_11 0x2200d8 /* uController/UART 1 register */ -#define MD_UREG1_12 0x2200e0 /* uController/UART 1 register */ -#define MD_UREG1_13 0x2200e8 /* uController/UART 1 register */ -#define MD_UREG1_14 0x2200f0 /* uController/UART 1 register */ -#define MD_UREG1_15 0x2200f8 /* uController/UART 1 register */ - -#ifdef CONFIG_SGI_SN_N_MODE -#define MD_MEM_BANKS 4 /* 4 banks of memory max in N mode */ -#else -#define MD_MEM_BANKS 8 /* 8 banks of memory max in M mode */ -#endif - -/* - * MD_MEMORY_CONFIG fields - * - * MD_SIZE_xxx are useful for representing the size of a SIMM or bank - * (SIMM pair). They correspond to the values needed for the bit - * triplets (MMC_BANK_MASK) in the MD_MEMORY_CONFIG register for bank size. - * Bits not used by the MD are used by software. - */ - -#define MD_SIZE_EMPTY 0 /* Valid in MEMORY_CONFIG */ -#define MD_SIZE_8MB 1 -#define MD_SIZE_16MB 2 -#define MD_SIZE_32MB 3 /* Broken in Hub 1 */ -#define MD_SIZE_64MB 4 /* Valid in MEMORY_CONFIG */ -#define MD_SIZE_128MB 5 /* Valid in MEMORY_CONFIG */ -#define MD_SIZE_256MB 6 -#define MD_SIZE_512MB 7 /* Valid in MEMORY_CONFIG */ -#define MD_SIZE_1GB 8 -#define MD_SIZE_2GB 9 -#define MD_SIZE_4GB 10 - -#define MD_SIZE_BYTES(size) ((size) == 0 ? 0 : 0x400000L << (size)) -#define MD_SIZE_MBYTES(size) ((size) == 0 ? 0 : 4 << (size)) - -#define MMC_FPROM_CYC_SHFT 49 /* Have to use UINT64_CAST, instead */ -#define MMC_FPROM_CYC_MASK (UINT64_CAST 31 << 49) /* of 'L' suffix, */ -#define MMC_FPROM_WR_SHFT 44 /* for assembler */ -#define MMC_FPROM_WR_MASK (UINT64_CAST 31 << 44) -#define MMC_UCTLR_CYC_SHFT 39 -#define MMC_UCTLR_CYC_MASK (UINT64_CAST 31 << 39) -#define MMC_UCTLR_WR_SHFT 34 -#define MMC_UCTLR_WR_MASK (UINT64_CAST 31 << 34) -#define MMC_DIMM0_SEL_SHFT 32 -#define MMC_DIMM0_SEL_MASK (UINT64_CAST 3 << 32) -#define MMC_IO_PROT_EN_SHFT 31 -#define MMC_IO_PROT_EN_MASK (UINT64_CAST 1 << 31) -#define MMC_IO_PROT (UINT64_CAST 1 << 31) -#define MMC_ARB_MLSS_SHFT 30 -#define MMC_ARB_MLSS_MASK (UINT64_CAST 1 << 30) -#define MMC_ARB_MLSS (UINT64_CAST 1 << 30) -#define MMC_IGNORE_ECC_SHFT 29 -#define MMC_IGNORE_ECC_MASK (UINT64_CAST 1 << 29) -#define MMC_IGNORE_ECC (UINT64_CAST 1 << 29) -#define MMC_DIR_PREMIUM_SHFT 28 -#define MMC_DIR_PREMIUM_MASK (UINT64_CAST 1 << 28) -#define MMC_DIR_PREMIUM (UINT64_CAST 1 << 28) -#define MMC_REPLY_GUAR_SHFT 24 -#define MMC_REPLY_GUAR_MASK (UINT64_CAST 15 << 24) -#define MMC_BANK_SHFT(_b) ((_b) * 3) -#define MMC_BANK_MASK(_b) (UINT64_CAST 7 << MMC_BANK_SHFT(_b)) -#define MMC_BANK_ALL_MASK 0xffffff -#define MMC_RESET_DEFAULTS (UINT64_CAST 0x0f << MMC_FPROM_CYC_SHFT | \ - UINT64_CAST 0x07 << MMC_FPROM_WR_SHFT | \ - UINT64_CAST 0x1f << MMC_UCTLR_CYC_SHFT | \ - UINT64_CAST 0x0f << MMC_UCTLR_WR_SHFT | \ - MMC_IGNORE_ECC | MMC_DIR_PREMIUM | \ - UINT64_CAST 0x0f << MMC_REPLY_GUAR_SHFT | \ - MMC_BANK_ALL_MASK) - -/* MD_REFRESH_CONTROL fields */ - -#define MRC_ENABLE_SHFT 63 -#define MRC_ENABLE_MASK (UINT64_CAST 1 << 63) -#define MRC_ENABLE (UINT64_CAST 1 << 63) -#define MRC_COUNTER_SHFT 12 -#define MRC_COUNTER_MASK (UINT64_CAST 0xfff << 12) -#define MRC_CNT_THRESH_MASK 0xfff -#define MRC_RESET_DEFAULTS (UINT64_CAST 0x400) - -/* MD_MEM_DIMM_INIT and MD_DIR_DIMM_INIT fields */ - -#define MDI_SELECT_SHFT 32 -#define MDI_SELECT_MASK (UINT64_CAST 0x0f << 32) -#define MDI_DIMM_MODE_MASK (UINT64_CAST 0xfff) - -/* MD_MOQ_SIZE fields */ - -#define MMS_RP_SIZE_SHFT 8 -#define MMS_RP_SIZE_MASK (UINT64_CAST 0x3f << 8) -#define MMS_RQ_SIZE_SHFT 0 -#define MMS_RQ_SIZE_MASK (UINT64_CAST 0x1f) -#define MMS_RESET_DEFAULTS (0x32 << 8 | 0x12) - -/* MD_FANDOP_CAC_STAT fields */ - -#define MFC_VALID_SHFT 63 -#define MFC_VALID_MASK (UINT64_CAST 1 << 63) -#define MFC_VALID (UINT64_CAST 1 << 63) -#define MFC_ADDR_SHFT 6 -#define MFC_ADDR_MASK (UINT64_CAST 0x3ffffff) - -/* MD_MLAN_CTL fields */ - -#define MLAN_PHI1_SHFT 27 -#define MLAN_PHI1_MASK (UINT64_CAST 0x7f << 27) -#define MLAN_PHI0_SHFT 20 -#define MLAN_PHI0_MASK (UINT64_CAST 0x7f << 27) -#define MLAN_PULSE_SHFT 10 -#define MLAN_PULSE_MASK (UINT64_CAST 0x3ff << 10) -#define MLAN_SAMPLE_SHFT 2 -#define MLAN_SAMPLE_MASK (UINT64_CAST 0xff << 2) -#define MLAN_DONE_SHFT 1 -#define MLAN_DONE_MASK 2 -#define MLAN_DONE (UINT64_CAST 0x02) -#define MLAN_RD_DATA (UINT64_CAST 0x01) -#define MLAN_RESET_DEFAULTS (UINT64_CAST 0x31 << MLAN_PHI1_SHFT | \ - UINT64_CAST 0x31 << MLAN_PHI0_SHFT) - -/* MD_SLOTID_USTAT bit definitions */ - -#define MSU_CORECLK_TST_SHFT 7 /* You don't wanna know */ -#define MSU_CORECLK_TST_MASK (UINT64_CAST 1 << 7) -#define MSU_CORECLK_TST (UINT64_CAST 1 << 7) -#define MSU_CORECLK_SHFT 6 /* You don't wanna know */ -#define MSU_CORECLK_MASK (UINT64_CAST 1 << 6) -#define MSU_CORECLK (UINT64_CAST 1 << 6) -#define MSU_NETSYNC_SHFT 5 /* You don't wanna know */ -#define MSU_NETSYNC_MASK (UINT64_CAST 1 << 5) -#define MSU_NETSYNC (UINT64_CAST 1 << 5) -#define MSU_FPROMRDY_SHFT 4 /* Flash PROM ready bit */ -#define MSU_FPROMRDY_MASK (UINT64_CAST 1 << 4) -#define MSU_FPROMRDY (UINT64_CAST 1 << 4) -#define MSU_I2CINTR_SHFT 3 /* I2C interrupt bit */ -#define MSU_I2CINTR_MASK (UINT64_CAST 1 << 3) -#define MSU_I2CINTR (UINT64_CAST 1 << 3) -#define MSU_SLOTID_MASK 0xff -#define MSU_SN0_SLOTID_SHFT 0 /* Slot ID */ -#define MSU_SN0_SLOTID_MASK (UINT64_CAST 7) -#define MSU_SN00_SLOTID_SHFT 7 -#define MSU_SN00_SLOTID_MASK (UINT64_CAST 0x80) - -#define MSU_PIMM_PSC_SHFT 4 -#define MSU_PIMM_PSC_MASK (0xf << MSU_PIMM_PSC_SHFT) - -/* MD_MIG_DIFF_THRESH bit definitions */ - -#define MD_MIG_DIFF_THRES_VALID_MASK (UINT64_CAST 0x1 << 63) -#define MD_MIG_DIFF_THRES_VALID_SHFT 63 -#define MD_MIG_DIFF_THRES_VALUE_MASK (UINT64_CAST 0xfffff) - -/* MD_MIG_VALUE_THRESH bit definitions */ - -#define MD_MIG_VALUE_THRES_VALID_MASK (UINT64_CAST 0x1 << 63) -#define MD_MIG_VALUE_THRES_VALID_SHFT 63 -#define MD_MIG_VALUE_THRES_VALUE_MASK (UINT64_CAST 0xfffff) - -/* MD_MIG_CANDIDATE bit definitions */ - -#define MD_MIG_CANDIDATE_VALID_MASK (UINT64_CAST 0x1 << 63) -#define MD_MIG_CANDIDATE_VALID_SHFT 63 -#define MD_MIG_CANDIDATE_TYPE_MASK (UINT64_CAST 0x1 << 30) -#define MD_MIG_CANDIDATE_TYPE_SHFT 30 -#define MD_MIG_CANDIDATE_OVERRUN_MASK (UINT64_CAST 0x1 << 29) -#define MD_MIG_CANDIDATE_OVERRUN_SHFT 29 -#define MD_MIG_CANDIDATE_INITIATOR_MASK (UINT64_CAST 0x7ff << 18) -#define MD_MIG_CANDIDATE_INITIATOR_SHFT 18 -#define MD_MIG_CANDIDATE_NODEID_MASK (UINT64_CAST 0x1ff << 20) -#define MD_MIG_CANDIDATE_NODEID_SHFT 20 -#define MD_MIG_CANDIDATE_ADDR_MASK (UINT64_CAST 0x3ffff) -#define MD_MIG_CANDIDATE_ADDR_SHFT 14 /* The address starts at bit 14 */ - -/* Other MD definitions */ - -#define MD_BANK_SHFT 29 /* log2(512 MB) */ -#define MD_BANK_MASK (UINT64_CAST 7 << 29) -#define MD_BANK_SIZE (UINT64_CAST 1 << MD_BANK_SHFT) /* 512 MB */ -#define MD_BANK_OFFSET(_b) (UINT64_CAST (_b) << MD_BANK_SHFT) - -/* - * The following definitions cover the bit field definitions for the - * various MD registers. For multi-bit registers, we define both - * a shift amount and a mask value. By convention, if you want to - * isolate a field, you should mask the field and then shift it down, - * since this makes the masks useful without a shift. - */ - -/* Directory entry states for both premium and standard SIMMs. */ - -#define MD_DIR_SHARED (UINT64_CAST 0x0) /* 000 */ -#define MD_DIR_POISONED (UINT64_CAST 0x1) /* 001 */ -#define MD_DIR_EXCLUSIVE (UINT64_CAST 0x2) /* 010 */ -#define MD_DIR_BUSY_SHARED (UINT64_CAST 0x3) /* 011 */ -#define MD_DIR_BUSY_EXCL (UINT64_CAST 0x4) /* 100 */ -#define MD_DIR_WAIT (UINT64_CAST 0x5) /* 101 */ -#define MD_DIR_UNOWNED (UINT64_CAST 0x7) /* 111 */ - -/* - * The MD_DIR_FORCE_ECC bit can be added directory entry write data - * to forcing the ECC to be written as-is instead of recalculated. - */ - -#define MD_DIR_FORCE_ECC (UINT64_CAST 1 << 63) - -/* - * Premium SIMM directory entry shifts and masks. Each is valid only in the - * context(s) indicated, where A, B, and C indicate the directory entry format - * as shown, and low and/or high indicates which double-word of the entry. - * - * Format A: STATE = shared, FINE = 1 - * Format B: STATE = shared, FINE = 0 - * Format C: STATE != shared (FINE must be 0) - */ - -#define MD_PDIR_MASK 0xffffffffffff /* Whole entry */ -#define MD_PDIR_ECC_SHFT 0 /* ABC low or high */ -#define MD_PDIR_ECC_MASK 0x7f -#define MD_PDIR_PRIO_SHFT 8 /* ABC low */ -#define MD_PDIR_PRIO_MASK (0xf << 8) -#define MD_PDIR_AX_SHFT 7 /* ABC low */ -#define MD_PDIR_AX_MASK (1 << 7) -#define MD_PDIR_AX (1 << 7) -#define MD_PDIR_FINE_SHFT 12 /* ABC low */ -#define MD_PDIR_FINE_MASK (1 << 12) -#define MD_PDIR_FINE (1 << 12) -#define MD_PDIR_OCT_SHFT 13 /* A low */ -#define MD_PDIR_OCT_MASK (7 << 13) -#define MD_PDIR_STATE_SHFT 13 /* BC low */ -#define MD_PDIR_STATE_MASK (7 << 13) -#define MD_PDIR_ONECNT_SHFT 16 /* BC low */ -#define MD_PDIR_ONECNT_MASK (0x3f << 16) -#define MD_PDIR_PTR_SHFT 22 /* C low */ -#define MD_PDIR_PTR_MASK (UINT64_CAST 0x7ff << 22) -#define MD_PDIR_VECMSB_SHFT 22 /* AB low */ -#define MD_PDIR_VECMSB_BITMASK 0x3ffffff -#define MD_PDIR_VECMSB_BITSHFT 27 -#define MD_PDIR_VECMSB_MASK (UINT64_CAST MD_PDIR_VECMSB_BITMASK << 22) -#define MD_PDIR_CWOFF_SHFT 7 /* C high */ -#define MD_PDIR_CWOFF_MASK (7 << 7) -#define MD_PDIR_VECLSB_SHFT 10 /* AB high */ -#define MD_PDIR_VECLSB_BITMASK (UINT64_CAST 0x3fffffffff) -#define MD_PDIR_VECLSB_BITSHFT 0 -#define MD_PDIR_VECLSB_MASK (MD_PDIR_VECLSB_BITMASK << 10) - -/* - * Directory initialization values - */ - -#define MD_PDIR_INIT_LO (MD_DIR_UNOWNED << MD_PDIR_STATE_SHFT | \ - MD_PDIR_AX) -#define MD_PDIR_INIT_HI 0 -#define MD_PDIR_INIT_PROT (MD_PROT_RW << MD_PPROT_IO_SHFT | \ - MD_PROT_RW << MD_PPROT_SHFT) - -/* - * Standard SIMM directory entry shifts and masks. Each is valid only in the - * context(s) indicated, where A and C indicate the directory entry format - * as shown, and low and/or high indicates which double-word of the entry. - * - * Format A: STATE == shared - * Format C: STATE != shared - */ - -#define MD_SDIR_MASK 0xffff /* Whole entry */ -#define MD_SDIR_ECC_SHFT 0 /* AC low or high */ -#define MD_SDIR_ECC_MASK 0x1f -#define MD_SDIR_PRIO_SHFT 6 /* AC low */ -#define MD_SDIR_PRIO_MASK (1 << 6) -#define MD_SDIR_AX_SHFT 5 /* AC low */ -#define MD_SDIR_AX_MASK (1 << 5) -#define MD_SDIR_AX (1 << 5) -#define MD_SDIR_STATE_SHFT 7 /* AC low */ -#define MD_SDIR_STATE_MASK (7 << 7) -#define MD_SDIR_PTR_SHFT 10 /* C low */ -#define MD_SDIR_PTR_MASK (0x3f << 10) -#define MD_SDIR_CWOFF_SHFT 5 /* C high */ -#define MD_SDIR_CWOFF_MASK (7 << 5) -#define MD_SDIR_VECMSB_SHFT 11 /* A low */ -#define MD_SDIR_VECMSB_BITMASK 0x1f -#define MD_SDIR_VECMSB_BITSHFT 7 -#define MD_SDIR_VECMSB_MASK (MD_SDIR_VECMSB_BITMASK << 11) -#define MD_SDIR_VECLSB_SHFT 5 /* A high */ -#define MD_SDIR_VECLSB_BITMASK 0x7ff -#define MD_SDIR_VECLSB_BITSHFT 0 -#define MD_SDIR_VECLSB_MASK (MD_SDIR_VECLSB_BITMASK << 5) - -/* - * Directory initialization values - */ - -#define MD_SDIR_INIT_LO (MD_DIR_UNOWNED << MD_SDIR_STATE_SHFT | \ - MD_SDIR_AX) -#define MD_SDIR_INIT_HI 0 -#define MD_SDIR_INIT_PROT (MD_PROT_RW << MD_SPROT_SHFT) - -/* Protection and migration field values */ - -#define MD_PROT_RW (UINT64_CAST 0x6) -#define MD_PROT_RO (UINT64_CAST 0x3) -#define MD_PROT_NO (UINT64_CAST 0x0) -#define MD_PROT_BAD (UINT64_CAST 0x5) - -/* Premium SIMM protection entry shifts and masks. */ - -#define MD_PPROT_SHFT 0 /* Prot. field */ -#define MD_PPROT_MASK 7 -#define MD_PPROT_MIGMD_SHFT 3 /* Migration mode */ -#define MD_PPROT_MIGMD_MASK (3 << 3) -#define MD_PPROT_REFCNT_SHFT 5 /* Reference count */ -#define MD_PPROT_REFCNT_WIDTH 0x7ffff -#define MD_PPROT_REFCNT_MASK (MD_PPROT_REFCNT_WIDTH << 5) - -#define MD_PPROT_IO_SHFT 45 /* I/O Prot field */ -#define MD_PPROT_IO_MASK (UINT64_CAST 7 << 45) - -/* Standard SIMM protection entry shifts and masks. */ - -#define MD_SPROT_SHFT 0 /* Prot. field */ -#define MD_SPROT_MASK 7 -#define MD_SPROT_MIGMD_SHFT 3 /* Migration mode */ -#define MD_SPROT_MIGMD_MASK (3 << 3) -#define MD_SPROT_REFCNT_SHFT 5 /* Reference count */ -#define MD_SPROT_REFCNT_WIDTH 0x7ff -#define MD_SPROT_REFCNT_MASK (MD_SPROT_REFCNT_WIDTH << 5) - -/* Migration modes used in protection entries */ - -#define MD_PROT_MIGMD_IREL (UINT64_CAST 0x3 << 3) -#define MD_PROT_MIGMD_IABS (UINT64_CAST 0x2 << 3) -#define MD_PROT_MIGMD_PREL (UINT64_CAST 0x1 << 3) -#define MD_PROT_MIGMD_OFF (UINT64_CAST 0x0 << 3) - - -/* - * Operations on page migration threshold register - */ - -#ifndef __ASSEMBLY__ - -/* - * LED register macros - */ - -#define CPU_LED_ADDR(_nasid, _slice) \ - (private.p_sn00 ? \ - REMOTE_HUB_ADDR((_nasid), MD_UREG1_0 + ((_slice) << 5)) : \ - REMOTE_HUB_ADDR((_nasid), MD_LED0 + ((_slice) << 3))) - -#define SET_CPU_LEDS(_nasid, _slice, _val) \ - (HUB_S(CPU_LED_ADDR(_nasid, _slice), (_val))) - -#define SET_MY_LEDS(_v) \ - SET_CPU_LEDS(get_nasid(), get_slice(), (_v)) - -/* - * Operations on Memory/Directory DIMM control register - */ - -#define DIRTYPE_PREMIUM 1 -#define DIRTYPE_STANDARD 0 -#define MD_MEMORY_CONFIG_DIR_TYPE_GET(region) (\ - (REMOTE_HUB_L(region, MD_MEMORY_CONFIG) & MMC_DIR_PREMIUM_MASK) >> \ - MMC_DIR_PREMIUM_SHFT) - - -/* - * Operations on page migration count difference and absolute threshold - * registers - */ - -#define MD_MIG_DIFF_THRESH_GET(region) ( \ - REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) & \ - MD_MIG_DIFF_THRES_VALUE_MASK) - -#define MD_MIG_DIFF_THRESH_SET(region, value) ( \ - REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH, \ - MD_MIG_DIFF_THRES_VALID_MASK | (value))) - -#define MD_MIG_DIFF_THRESH_DISABLE(region) ( \ - REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH, \ - REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) \ - & ~MD_MIG_DIFF_THRES_VALID_MASK)) - -#define MD_MIG_DIFF_THRESH_ENABLE(region) ( \ - REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH, \ - REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) \ - | MD_MIG_DIFF_THRES_VALID_MASK)) - -#define MD_MIG_DIFF_THRESH_IS_ENABLED(region) ( \ - REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) & \ - MD_MIG_DIFF_THRES_VALID_MASK) - -#define MD_MIG_VALUE_THRESH_GET(region) ( \ - REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH) & \ - MD_MIG_VALUE_THRES_VALUE_MASK) - -#define MD_MIG_VALUE_THRESH_SET(region, value) ( \ - REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH, \ - MD_MIG_VALUE_THRES_VALID_MASK | (value))) - -#define MD_MIG_VALUE_THRESH_DISABLE(region) ( \ - REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH, \ - REMOTE_HUB_L(region, MD_MIG_VALUE_THRESH) \ - & ~MD_MIG_VALUE_THRES_VALID_MASK)) - -#define MD_MIG_VALUE_THRESH_ENABLE(region) ( \ - REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH, \ - REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH) \ - | MD_MIG_VALUE_THRES_VALID_MASK)) - -#define MD_MIG_VALUE_THRESH_IS_ENABLED(region) ( \ - REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH) & \ - MD_MIG_VALUE_THRES_VALID_MASK) - -/* - * Operations on page migration candidate register - */ - -#define MD_MIG_CANDIDATE_GET(my_region_id) ( \ - REMOTE_HUB_L((my_region_id), MD_MIG_CANDIDATE_CLR)) - -#define MD_MIG_CANDIDATE_HWPFN(value) ((value) & MD_MIG_CANDIDATE_ADDR_MASK) - -#define MD_MIG_CANDIDATE_NODEID(value) ( \ - ((value) & MD_MIG_CANDIDATE_NODEID_MASK) >> MD_MIG_CANDIDATE_NODEID_SHFT) - -#define MD_MIG_CANDIDATE_TYPE(value) ( \ - ((value) & MD_MIG_CANDIDATE_TYPE_MASK) >> MD_MIG_CANDIDATE_TYPE_SHFT) - -#define MD_MIG_CANDIDATE_VALID(value) ( \ - ((value) & MD_MIG_CANDIDATE_VALID_MASK) >> MD_MIG_CANDIDATE_VALID_SHFT) - -/* - * Macros to retrieve fields in the protection entry - */ - -/* for Premium SIMM */ -#define MD_PPROT_REFCNT_GET(value) ( \ - ((value) & MD_PPROT_REFCNT_MASK) >> MD_PPROT_REFCNT_SHFT) - -#define MD_PPROT_MIGMD_GET(value) ( \ - ((value) & MD_PPROT_MIGMD_MASK) >> MD_PPROT_MIGMD_SHFT) - -/* for Standard SIMM */ -#define MD_SPROT_REFCNT_GET(value) ( \ - ((value) & MD_SPROT_REFCNT_MASK) >> MD_SPROT_REFCNT_SHFT) - -#define MD_SPROT_MIGMD_GET(value) ( \ - ((value) & MD_SPROT_MIGMD_MASK) >> MD_SPROT_MIGMD_SHFT) - -/* - * Format of dir_error, mem_error, protocol_error and misc_error registers - */ - -struct dir_error_reg { - u64 uce_vld: 1, /* 63: valid directory uce */ - ae_vld: 1, /* 62: valid dir prot ecc error */ - ce_vld: 1, /* 61: valid correctable ECC err*/ - rsvd1: 19, /* 60-42: reserved */ - bad_prot: 3, /* 41-39: encoding, bad access rights*/ - bad_syn: 7, /* 38-32: bad dir syndrome */ - rsvd2: 2, /* 31-30: reserved */ - hspec_addr:27, /* 29-03: bddir space bad entry */ - uce_ovr: 1, /* 2: multiple dir uce's */ - ae_ovr: 1, /* 1: multiple prot ecc errs*/ - ce_ovr: 1; /* 0: multiple correctable errs */ -}; - -typedef union md_dir_error { - u64 derr_reg; /* the entire register */ - struct dir_error_reg derr_fmt; /* the register format */ -} md_dir_error_t; - - -struct mem_error_reg { - u64 uce_vld: 1, /* 63: valid memory uce */ - ce_vld: 1, /* 62: valid correctable ECC err*/ - rsvd1: 22, /* 61-40: reserved */ - bad_syn: 8, /* 39-32: bad mem ecc syndrome */ - address: 29, /* 31-03: bad entry pointer */ - rsvd2: 1, /* 2: reserved */ - uce_ovr: 1, /* 1: multiple mem uce's */ - ce_ovr: 1; /* 0: multiple correctable errs */ -}; - - -typedef union md_mem_error { - u64 merr_reg; /* the entire register */ - struct mem_error_reg merr_fmt; /* format of the mem_error reg */ -} md_mem_error_t; - - -struct proto_error_reg { - u64 valid: 1, /* 63: valid protocol error */ - rsvd1: 2, /* 62-61: reserved */ - initiator:11, /* 60-50: id of request initiator*/ - backoff: 2, /* 49-48: backoff control */ - msg_type: 8, /* 47-40: type of request */ - access: 2, /* 39-38: access rights of initiator*/ - priority: 1, /* 37: priority level of requestor*/ - dir_state: 4, /* 36-33: state of directory */ - pointer_me:1, /* 32: initiator same as dir ptr */ - address: 29, /* 31-03: request address */ - rsvd2: 2, /* 02-01: reserved */ - overrun: 1; /* 0: multiple protocol errs */ -}; - -typedef union md_proto_error { - u64 perr_reg; /* the entire register */ - struct proto_error_reg perr_fmt; /* format of the register */ -} md_proto_error_t; - - -struct md_sdir_high_fmt { - unsigned short sd_hi_bvec : 11, - sd_hi_ecc : 5; -}; - - -typedef union md_sdir_high { - /* The 16 bits of standard directory, upper word */ - unsigned short sd_hi_val; - struct md_sdir_high_fmt sd_hi_fmt; -}md_sdir_high_t; - - -struct md_sdir_low_shared_fmt { - /* The meaning of lower directory, shared */ - unsigned short sds_lo_bvec : 5, - sds_lo_unused: 1, - sds_lo_state : 3, - sds_lo_prio : 1, - sds_lo_ax : 1, - sds_lo_ecc : 5; -}; - -struct md_sdir_low_exclusive_fmt { - /* The meaning of lower directory, exclusive */ - unsigned short sde_lo_ptr : 6, - sde_lo_state : 3, - sde_lo_prio : 1, - sde_lo_ax : 1, - sde_lo_ecc : 5; -}; - - -typedef union md_sdir_low { - /* The 16 bits of standard directory, lower word */ - unsigned short sd_lo_val; - struct md_sdir_low_exclusive_fmt sde_lo_fmt; - struct md_sdir_low_shared_fmt sds_lo_fmt; -}md_sdir_low_t; - - - -struct md_pdir_high_fmt { - u64 pd_hi_unused : 16, - pd_hi_bvec : 38, - pd_hi_unused1 : 3, - pd_hi_ecc : 7; -}; - - -typedef union md_pdir_high { - /* The 48 bits of standard directory, upper word */ - u64 pd_hi_val; - struct md_pdir_high_fmt pd_hi_fmt; -}md_pdir_high_t; - - -struct md_pdir_low_shared_fmt { - /* The meaning of lower directory, shared */ - u64 pds_lo_unused : 16, - pds_lo_bvec : 26, - pds_lo_cnt : 6, - pds_lo_state : 3, - pds_lo_ste : 1, - pds_lo_prio : 4, - pds_lo_ax : 1, - pds_lo_ecc : 7; -}; - -struct md_pdir_low_exclusive_fmt { - /* The meaning of lower directory, exclusive */ - u64 pde_lo_unused : 31, - pde_lo_ptr : 11, - pde_lo_unused1 : 6, - pde_lo_state : 3, - pde_lo_ste : 1, - pde_lo_prio : 4, - pde_lo_ax : 1, - pde_lo_ecc : 7; -}; - - -typedef union md_pdir_loent { - /* The 48 bits of premium directory, lower word */ - u64 pd_lo_val; - struct md_pdir_low_exclusive_fmt pde_lo_fmt; - struct md_pdir_low_shared_fmt pds_lo_fmt; -}md_pdir_low_t; - - -/* - * the following two "union" definitions and two - * "struct" definitions are used in vmdump.c to - * represent directory memory information. - */ - -typedef union md_dir_high { - md_sdir_high_t md_sdir_high; - md_pdir_high_t md_pdir_high; -} md_dir_high_t; - -typedef union md_dir_low { - md_sdir_low_t md_sdir_low; - md_pdir_low_t md_pdir_low; -} md_dir_low_t; - -typedef struct bddir_entry { - md_dir_low_t md_dir_low; - md_dir_high_t md_dir_high; -} bddir_entry_t; - -typedef struct dir_mem_entry { - u64 prcpf[MAX_REGIONS]; - bddir_entry_t directory_words[MD_PAGE_SIZE/CACHE_SLINE_SIZE]; -} dir_mem_entry_t; - - - -typedef union md_perf_sel { - u64 perf_sel_reg; - struct { - u64 perf_rsvd : 60, - perf_en : 1, - perf_sel : 3; - } perf_sel_bits; -} md_perf_sel_t; - -typedef union md_perf_cnt { - u64 perf_cnt; - struct { - u64 perf_rsvd : 44, - perf_cnt : 20; - } perf_cnt_bits; -} md_perf_cnt_t; - - -#endif /* !__ASSEMBLY__ */ - - -#define DIR_ERROR_VALID_MASK 0xe000000000000000 -#define DIR_ERROR_VALID_SHFT 61 -#define DIR_ERROR_VALID_UCE 0x8000000000000000 -#define DIR_ERROR_VALID_AE 0x4000000000000000 -#define DIR_ERROR_VALID_CE 0x2000000000000000 - -#define MEM_ERROR_VALID_MASK 0xc000000000000000 -#define MEM_ERROR_VALID_SHFT 62 -#define MEM_ERROR_VALID_UCE 0x8000000000000000 -#define MEM_ERROR_VALID_CE 0x4000000000000000 - -#define PROTO_ERROR_VALID_MASK 0x8000000000000000 - -#define MISC_ERROR_VALID_MASK 0x3ff - -/* - * Mask for hspec address that is stored in the dir error register. - * This represents bits 29 through 3. - */ -#define DIR_ERR_HSPEC_MASK 0x3ffffff8 -#define ERROR_HSPEC_MASK 0x3ffffff8 -#define ERROR_HSPEC_SHFT 3 -#define ERROR_ADDR_MASK 0xfffffff8 -#define ERROR_ADDR_SHFT 3 - -/* - * MD_MISC_ERROR register defines. - */ - -#define MMCE_VALID_MASK 0x3ff -#define MMCE_ILL_MSG_SHFT 8 -#define MMCE_ILL_MSG_MASK (UINT64_CAST 0x03 << MMCE_ILL_MSG_SHFT) -#define MMCE_ILL_REV_SHFT 6 -#define MMCE_ILL_REV_MASK (UINT64_CAST 0x03 << MMCE_ILL_REV_SHFT) -#define MMCE_LONG_PACK_SHFT 4 -#define MMCE_LONG_PACK_MASK (UINT64_CAST 0x03 << MMCE_lONG_PACK_SHFT) -#define MMCE_SHORT_PACK_SHFT 2 -#define MMCE_SHORT_PACK_MASK (UINT64_CAST 0x03 << MMCE_SHORT_PACK_SHFT) -#define MMCE_BAD_DATA_SHFT 0 -#define MMCE_BAD_DATA_MASK (UINT64_CAST 0x03 << MMCE_BAD_DATA_SHFT) - - -#define MD_PERF_COUNTERS 6 -#define MD_PERF_SETS 6 - -#define MEM_DIMM_MASK 0xe0000000 -#define MEM_DIMM_SHFT 29 - -#endif /* _ASM_SN_SN0_HUBMD_H */ diff --git a/include/asm-mips/sn/sn0/hubni.h b/include/asm-mips/sn/sn0/hubni.h deleted file mode 100644 index b40d3ef97a12..000000000000 --- a/include/asm-mips/sn/sn0/hubni.h +++ /dev/null @@ -1,255 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/hubni.h>, Revision 1.27. - * - * Copyright (C) 1992-1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SGI_SN0_HUBNI_H -#define _ASM_SGI_SN0_HUBNI_H - -#ifndef __ASSEMBLY__ -#include <linux/types.h> -#endif - -/* - * Hub Network Interface registers - * - * All registers in this file are subject to change until Hub chip tapeout. - */ - -#define NI_BASE 0x600000 -#define NI_BASE_TABLES 0x630000 - -#define NI_STATUS_REV_ID 0x600000 /* Hub network status, rev, and ID */ -#define NI_PORT_RESET 0x600008 /* Reset the network interface */ -#define NI_PROTECTION 0x600010 /* NI register access permissions */ -#define NI_GLOBAL_PARMS 0x600018 /* LLP parameters */ -#define NI_SCRATCH_REG0 0x600100 /* Scratch register 0 (64 bits) */ -#define NI_SCRATCH_REG1 0x600108 /* Scratch register 1 (64 bits) */ -#define NI_DIAG_PARMS 0x600110 /* Parameters for diags */ - -#define NI_VECTOR_PARMS 0x600200 /* Vector PIO routing parameters */ -#define NI_VECTOR 0x600208 /* Vector PIO route */ -#define NI_VECTOR_DATA 0x600210 /* Vector PIO data */ -#define NI_VECTOR_STATUS 0x600300 /* Vector PIO return status */ -#define NI_RETURN_VECTOR 0x600308 /* Vector PIO return vector */ -#define NI_VECTOR_READ_DATA 0x600310 /* Vector PIO read data */ -#define NI_VECTOR_CLEAR 0x600380 /* Vector PIO read & clear status */ - -#define NI_IO_PROTECT 0x600400 /* PIO protection bits */ -#define NI_IO_PROT_OVRRD 0x600408 /* PIO protection bit override */ - -#define NI_AGE_CPU0_MEMORY 0x600500 /* CPU 0 memory age control */ -#define NI_AGE_CPU0_PIO 0x600508 /* CPU 0 PIO age control */ -#define NI_AGE_CPU1_MEMORY 0x600510 /* CPU 1 memory age control */ -#define NI_AGE_CPU1_PIO 0x600518 /* CPU 1 PIO age control */ -#define NI_AGE_GBR_MEMORY 0x600520 /* GBR memory age control */ -#define NI_AGE_GBR_PIO 0x600528 /* GBR PIO age control */ -#define NI_AGE_IO_MEMORY 0x600530 /* IO memory age control */ -#define NI_AGE_IO_PIO 0x600538 /* IO PIO age control */ -#define NI_AGE_REG_MIN NI_AGE_CPU0_MEMORY -#define NI_AGE_REG_MAX NI_AGE_IO_PIO - -#define NI_PORT_PARMS 0x608000 /* LLP Parameters */ -#define NI_PORT_ERROR 0x608008 /* LLP Errors */ -#define NI_PORT_ERROR_CLEAR 0x608088 /* Clear the error bits */ - -#define NI_META_TABLE0 0x638000 /* First meta routing table entry */ -#define NI_META_TABLE(_x) (NI_META_TABLE0 + (8 * (_x))) -#define NI_META_ENTRIES 32 - -#define NI_LOCAL_TABLE0 0x638100 /* First local routing table entry */ -#define NI_LOCAL_TABLE(_x) (NI_LOCAL_TABLE0 + (8 * (_x))) -#define NI_LOCAL_ENTRIES 16 - -/* - * NI_STATUS_REV_ID mask and shift definitions - * Have to use UINT64_CAST instead of 'L' suffix, for assembler. - */ - -#define NSRI_8BITMODE_SHFT 30 -#define NSRI_8BITMODE_MASK (UINT64_CAST 0x1 << 30) -#define NSRI_LINKUP_SHFT 29 -#define NSRI_LINKUP_MASK (UINT64_CAST 0x1 << 29) -#define NSRI_DOWNREASON_SHFT 28 /* 0=failed, 1=never came */ -#define NSRI_DOWNREASON_MASK (UINT64_CAST 0x1 << 28) /* out of reset. */ -#define NSRI_MORENODES_SHFT 18 -#define NSRI_MORENODES_MASK (UINT64_CAST 1 << 18) /* Max. # of nodes */ -#define MORE_MEMORY 0 -#define MORE_NODES 1 -#define NSRI_REGIONSIZE_SHFT 17 -#define NSRI_REGIONSIZE_MASK (UINT64_CAST 1 << 17) /* Granularity */ -#define REGIONSIZE_FINE 1 -#define REGIONSIZE_COARSE 0 -#define NSRI_NODEID_SHFT 8 -#define NSRI_NODEID_MASK (UINT64_CAST 0x1ff << 8)/* Node (Hub) ID */ -#define NSRI_REV_SHFT 4 -#define NSRI_REV_MASK (UINT64_CAST 0xf << 4) /* Chip Revision */ -#define NSRI_CHIPID_SHFT 0 -#define NSRI_CHIPID_MASK (UINT64_CAST 0xf) /* Chip type ID */ - -/* - * In fine mode, each node is a region. In coarse mode, there are - * eight nodes per region. - */ -#define NASID_TO_FINEREG_SHFT 0 -#define NASID_TO_COARSEREG_SHFT 3 - -/* NI_PORT_RESET mask definitions */ - -#define NPR_PORTRESET (UINT64_CAST 1 << 7) /* Send warm reset */ -#define NPR_LINKRESET (UINT64_CAST 1 << 1) /* Send link reset */ -#define NPR_LOCALRESET (UINT64_CAST 1) /* Reset entire hub */ - -/* NI_PROTECTION mask and shift definitions */ - -#define NPROT_RESETOK (UINT64_CAST 1) - -/* NI_GLOBAL_PARMS mask and shift definitions */ - -#define NGP_MAXRETRY_SHFT 48 /* Maximum retries */ -#define NGP_MAXRETRY_MASK (UINT64_CAST 0x3ff << 48) -#define NGP_TAILTOWRAP_SHFT 32 /* Tail timeout wrap */ -#define NGP_TAILTOWRAP_MASK (UINT64_CAST 0xffff << 32) - -#define NGP_CREDITTOVAL_SHFT 16 /* Tail timeout wrap */ -#define NGP_CREDITTOVAL_MASK (UINT64_CAST 0xf << 16) -#define NGP_TAILTOVAL_SHFT 4 /* Tail timeout value */ -#define NGP_TAILTOVAL_MASK (UINT64_CAST 0xf << 4) - -/* NI_DIAG_PARMS mask and shift definitions */ - -#define NDP_PORTTORESET (UINT64_CAST 1 << 18) /* Port tmout reset */ -#define NDP_LLP8BITMODE (UINT64_CAST 1 << 12) /* LLP 8-bit mode */ -#define NDP_PORTDISABLE (UINT64_CAST 1 << 6) /* Port disable */ -#define NDP_SENDERROR (UINT64_CAST 1) /* Send data error */ - -/* - * NI_VECTOR_PARMS mask and shift definitions. - * TYPE may be any of the first four PIOTYPEs defined under NI_VECTOR_STATUS. - */ - -#define NVP_PIOID_SHFT 40 -#define NVP_PIOID_MASK (UINT64_CAST 0x3ff << 40) -#define NVP_WRITEID_SHFT 32 -#define NVP_WRITEID_MASK (UINT64_CAST 0xff << 32) -#define NVP_ADDRESS_MASK (UINT64_CAST 0xffff8) /* Bits 19:3 */ -#define NVP_TYPE_SHFT 0 -#define NVP_TYPE_MASK (UINT64_CAST 0x3) - -/* NI_VECTOR_STATUS mask and shift definitions */ - -#define NVS_VALID (UINT64_CAST 1 << 63) -#define NVS_OVERRUN (UINT64_CAST 1 << 62) -#define NVS_TARGET_SHFT 51 -#define NVS_TARGET_MASK (UINT64_CAST 0x3ff << 51) -#define NVS_PIOID_SHFT 40 -#define NVS_PIOID_MASK (UINT64_CAST 0x3ff << 40) -#define NVS_WRITEID_SHFT 32 -#define NVS_WRITEID_MASK (UINT64_CAST 0xff << 32) -#define NVS_ADDRESS_MASK (UINT64_CAST 0xfffffff8) /* Bits 31:3 */ -#define NVS_TYPE_SHFT 0 -#define NVS_TYPE_MASK (UINT64_CAST 0x7) -#define NVS_ERROR_MASK (UINT64_CAST 0x4) /* bit set means error */ - - -#define PIOTYPE_READ 0 /* VECTOR_PARMS and VECTOR_STATUS */ -#define PIOTYPE_WRITE 1 /* VECTOR_PARMS and VECTOR_STATUS */ -#define PIOTYPE_UNDEFINED 2 /* VECTOR_PARMS and VECTOR_STATUS */ -#define PIOTYPE_EXCHANGE 3 /* VECTOR_PARMS and VECTOR_STATUS */ -#define PIOTYPE_ADDR_ERR 4 /* VECTOR_STATUS only */ -#define PIOTYPE_CMD_ERR 5 /* VECTOR_STATUS only */ -#define PIOTYPE_PROT_ERR 6 /* VECTOR_STATUS only */ -#define PIOTYPE_UNKNOWN 7 /* VECTOR_STATUS only */ - -/* NI_AGE_XXX mask and shift definitions */ - -#define NAGE_VCH_SHFT 10 -#define NAGE_VCH_MASK (UINT64_CAST 3 << 10) -#define NAGE_CC_SHFT 8 -#define NAGE_CC_MASK (UINT64_CAST 3 << 8) -#define NAGE_AGE_SHFT 0 -#define NAGE_AGE_MASK (UINT64_CAST 0xff) -#define NAGE_MASK (NAGE_VCH_MASK | NAGE_CC_MASK | NAGE_AGE_MASK) - -#define VCHANNEL_A 0 -#define VCHANNEL_B 1 -#define VCHANNEL_ANY 2 - -/* NI_PORT_PARMS mask and shift definitions */ - -#define NPP_NULLTO_SHFT 10 -#define NPP_NULLTO_MASK (UINT64_CAST 0x3f << 16) -#define NPP_MAXBURST_SHFT 0 -#define NPP_MAXBURST_MASK (UINT64_CAST 0x3ff) -#define NPP_RESET_DFLT_HUB20 ((UINT64_CAST 1 << NPP_NULLTO_SHFT) | \ - (UINT64_CAST 0x3f0 << NPP_MAXBURST_SHFT)) -#define NPP_RESET_DEFAULTS ((UINT64_CAST 6 << NPP_NULLTO_SHFT) | \ - (UINT64_CAST 0x3f0 << NPP_MAXBURST_SHFT)) - - -/* NI_PORT_ERROR mask and shift definitions */ - -#define NPE_LINKRESET (UINT64_CAST 1 << 37) -#define NPE_INTERNALERROR (UINT64_CAST 1 << 36) -#define NPE_BADMESSAGE (UINT64_CAST 1 << 35) -#define NPE_BADDEST (UINT64_CAST 1 << 34) -#define NPE_FIFOOVERFLOW (UINT64_CAST 1 << 33) -#define NPE_CREDITTO_SHFT 28 -#define NPE_CREDITTO_MASK (UINT64_CAST 0xf << 28) -#define NPE_TAILTO_SHFT 24 -#define NPE_TAILTO_MASK (UINT64_CAST 0xf << 24) -#define NPE_RETRYCOUNT_SHFT 16 -#define NPE_RETRYCOUNT_MASK (UINT64_CAST 0xff << 16) -#define NPE_CBERRCOUNT_SHFT 8 -#define NPE_CBERRCOUNT_MASK (UINT64_CAST 0xff << 8) -#define NPE_SNERRCOUNT_SHFT 0 -#define NPE_SNERRCOUNT_MASK (UINT64_CAST 0xff << 0) -#define NPE_MASK 0x3effffffff - -#define NPE_COUNT_MAX 0xff - -#define NPE_FATAL_ERRORS (NPE_LINKRESET | NPE_INTERNALERROR | \ - NPE_BADMESSAGE | NPE_BADDEST | \ - NPE_FIFOOVERFLOW | NPE_CREDITTO_MASK | \ - NPE_TAILTO_MASK) - -/* NI_META_TABLE mask and shift definitions */ - -#define NMT_EXIT_PORT_MASK (UINT64_CAST 0xf) - -/* NI_LOCAL_TABLE mask and shift definitions */ - -#define NLT_EXIT_PORT_MASK (UINT64_CAST 0xf) - -#ifndef __ASSEMBLY__ - -typedef union hubni_port_error_u { - u64 nipe_reg_value; - struct { - u64 nipe_rsvd: 26, /* unused */ - nipe_lnk_reset: 1, /* link reset */ - nipe_intl_err: 1, /* internal error */ - nipe_bad_msg: 1, /* bad message */ - nipe_bad_dest: 1, /* bad dest */ - nipe_fifo_ovfl: 1, /* fifo overflow */ - nipe_rsvd1: 1, /* unused */ - nipe_credit_to: 4, /* credit timeout */ - nipe_tail_to: 4, /* tail timeout */ - nipe_retry_cnt: 8, /* retry error count */ - nipe_cb_cnt: 8, /* checkbit error count */ - nipe_sn_cnt: 8; /* sequence number count */ - } nipe_fields_s; -} hubni_port_error_t; - -#define NI_LLP_RETRY_MAX 0xff -#define NI_LLP_CB_MAX 0xff -#define NI_LLP_SN_MAX 0xff - -#endif /* !__ASSEMBLY__ */ - -#endif /* _ASM_SGI_SN0_HUBNI_H */ diff --git a/include/asm-mips/sn/sn0/hubpi.h b/include/asm-mips/sn/sn0/hubpi.h deleted file mode 100644 index e39f5f9da040..000000000000 --- a/include/asm-mips/sn/sn0/hubpi.h +++ /dev/null @@ -1,409 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/hubpi.h>, revision 1.28. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_HUBPI_H -#define _ASM_SN_SN0_HUBPI_H - -#include <linux/types.h> - -/* - * Hub I/O interface registers - * - * All registers in this file are subject to change until Hub chip tapeout. - * All register "addresses" are actually offsets. Use the LOCAL_HUB - * or REMOTE_HUB macros to synthesize an actual address - */ - -#define PI_BASE 0x000000 - -/* General protection and control registers */ - -#define PI_CPU_PROTECT 0x000000 /* CPU Protection */ -#define PI_PROT_OVERRD 0x000008 /* Clear CPU Protection bit */ -#define PI_IO_PROTECT 0x000010 /* Interrupt Pending Protection */ -#define PI_REGION_PRESENT 0x000018 /* Indicates whether region exists */ -#define PI_CPU_NUM 0x000020 /* CPU Number ID */ -#define PI_CALIAS_SIZE 0x000028 /* Cached Alias Size */ -#define PI_MAX_CRB_TIMEOUT 0x000030 /* Maximum Timeout for CRB */ -#define PI_CRB_SFACTOR 0x000038 /* Scale factor for CRB timeout */ - -/* CALIAS values */ -#define PI_CALIAS_SIZE_0 0 -#define PI_CALIAS_SIZE_4K 1 -#define PI_CALIAS_SIZE_8K 2 -#define PI_CALIAS_SIZE_16K 3 -#define PI_CALIAS_SIZE_32K 4 -#define PI_CALIAS_SIZE_64K 5 -#define PI_CALIAS_SIZE_128K 6 -#define PI_CALIAS_SIZE_256K 7 -#define PI_CALIAS_SIZE_512K 8 -#define PI_CALIAS_SIZE_1M 9 -#define PI_CALIAS_SIZE_2M 10 -#define PI_CALIAS_SIZE_4M 11 -#define PI_CALIAS_SIZE_8M 12 -#define PI_CALIAS_SIZE_16M 13 -#define PI_CALIAS_SIZE_32M 14 -#define PI_CALIAS_SIZE_64M 15 - -/* Processor control and status checking */ - -#define PI_CPU_PRESENT_A 0x000040 /* CPU Present A */ -#define PI_CPU_PRESENT_B 0x000048 /* CPU Present B */ -#define PI_CPU_ENABLE_A 0x000050 /* CPU Enable A */ -#define PI_CPU_ENABLE_B 0x000058 /* CPU Enable B */ -#define PI_REPLY_LEVEL 0x000060 /* Reply Level */ -#define PI_HARDRESET_BIT 0x020068 /* Bit cleared by s/w on SR */ -#define PI_NMI_A 0x000070 /* NMI to CPU A */ -#define PI_NMI_B 0x000078 /* NMI to CPU B */ -#define PI_NMI_OFFSET (PI_NMI_B - PI_NMI_A) -#define PI_SOFTRESET 0x000080 /* Softreset (to both CPUs) */ - -/* Regular Interrupt register checking. */ - -#define PI_INT_PEND_MOD 0x000090 /* Write to set pending ints */ -#define PI_INT_PEND0 0x000098 /* Read to get pending ints */ -#define PI_INT_PEND1 0x0000a0 /* Read to get pending ints */ -#define PI_INT_MASK0_A 0x0000a8 /* Interrupt Mask 0 for CPU A */ -#define PI_INT_MASK1_A 0x0000b0 /* Interrupt Mask 1 for CPU A */ -#define PI_INT_MASK0_B 0x0000b8 /* Interrupt Mask 0 for CPU B */ -#define PI_INT_MASK1_B 0x0000c0 /* Interrupt Mask 1 for CPU B */ - -#define PI_INT_MASK_OFFSET 0x10 /* Offset from A to B */ - -/* Crosscall interrupts */ - -#define PI_CC_PEND_SET_A 0x0000c8 /* CC Interrupt Pending Set, CPU A */ -#define PI_CC_PEND_SET_B 0x0000d0 /* CC Interrupt Pending Set, CPU B */ -#define PI_CC_PEND_CLR_A 0x0000d8 /* CC Interrupt Pending Clr, CPU A */ -#define PI_CC_PEND_CLR_B 0x0000e0 /* CC Interrupt Pending Clr, CPU B */ -#define PI_CC_MASK 0x0000e8 /* CC Interrupt mask */ - -#define PI_INT_SET_OFFSET 0x08 /* Offset from A to B */ - -/* Realtime Counter and Profiler control registers */ - -#define PI_RT_COUNT 0x030100 /* Real Time Counter */ -#define PI_RT_COMPARE_A 0x000108 /* Real Time Compare A */ -#define PI_RT_COMPARE_B 0x000110 /* Real Time Compare B */ -#define PI_PROFILE_COMPARE 0x000118 /* L5 int to both cpus when == RTC */ -#define PI_RT_PEND_A 0x000120 /* Set if RT int for A pending */ -#define PI_RT_PEND_B 0x000128 /* Set if RT int for B pending */ -#define PI_PROF_PEND_A 0x000130 /* Set if Prof int for A pending */ -#define PI_PROF_PEND_B 0x000138 /* Set if Prof int for B pending */ -#define PI_RT_EN_A 0x000140 /* RT int for CPU A enable */ -#define PI_RT_EN_B 0x000148 /* RT int for CPU B enable */ -#define PI_PROF_EN_A 0x000150 /* PROF int for CPU A enable */ -#define PI_PROF_EN_B 0x000158 /* PROF int for CPU B enable */ -#define PI_RT_LOCAL_CTRL 0x000160 /* RT control register */ -#define PI_RT_FILTER_CTRL 0x000168 /* GCLK Filter control register */ - -#define PI_COUNT_OFFSET 0x08 /* A to B offset for all counts */ - -/* Built-In Self Test support */ - -#define PI_BIST_WRITE_DATA 0x000200 /* BIST write data */ -#define PI_BIST_READ_DATA 0x000208 /* BIST read data */ -#define PI_BIST_COUNT_TARG 0x000210 /* BIST Count and Target */ -#define PI_BIST_READY 0x000218 /* BIST Ready indicator */ -#define PI_BIST_SHIFT_LOAD 0x000220 /* BIST control */ -#define PI_BIST_SHIFT_UNLOAD 0x000228 /* BIST control */ -#define PI_BIST_ENTER_RUN 0x000230 /* BIST control */ - -/* Graphics control registers */ - -#define PI_GFX_PAGE_A 0x000300 /* Graphics page A */ -#define PI_GFX_CREDIT_CNTR_A 0x000308 /* Graphics credit counter A */ -#define PI_GFX_BIAS_A 0x000310 /* Graphics bias A */ -#define PI_GFX_INT_CNTR_A 0x000318 /* Graphics interrupt counter A */ -#define PI_GFX_INT_CMP_A 0x000320 /* Graphics interrupt comparator A */ -#define PI_GFX_PAGE_B 0x000328 /* Graphics page B */ -#define PI_GFX_CREDIT_CNTR_B 0x000330 /* Graphics credit counter B */ -#define PI_GFX_BIAS_B 0x000338 /* Graphics bias B */ -#define PI_GFX_INT_CNTR_B 0x000340 /* Graphics interrupt counter B */ -#define PI_GFX_INT_CMP_B 0x000348 /* Graphics interrupt comparator B */ - -#define PI_GFX_OFFSET (PI_GFX_PAGE_B - PI_GFX_PAGE_A) -#define PI_GFX_PAGE_ENABLE 0x0000010000000000LL - -/* Error and timeout registers */ -#define PI_ERR_INT_PEND 0x000400 /* Error Interrupt Pending */ -#define PI_ERR_INT_MASK_A 0x000408 /* Error Interrupt mask for CPU A */ -#define PI_ERR_INT_MASK_B 0x000410 /* Error Interrupt mask for CPU B */ -#define PI_ERR_STACK_ADDR_A 0x000418 /* Error stack address for CPU A */ -#define PI_ERR_STACK_ADDR_B 0x000420 /* Error stack address for CPU B */ -#define PI_ERR_STACK_SIZE 0x000428 /* Error Stack Size */ -#define PI_ERR_STATUS0_A 0x000430 /* Error Status 0A */ -#define PI_ERR_STATUS0_A_RCLR 0x000438 /* Error Status 0A clear on read */ -#define PI_ERR_STATUS1_A 0x000440 /* Error Status 1A */ -#define PI_ERR_STATUS1_A_RCLR 0x000448 /* Error Status 1A clear on read */ -#define PI_ERR_STATUS0_B 0x000450 /* Error Status 0B */ -#define PI_ERR_STATUS0_B_RCLR 0x000458 /* Error Status 0B clear on read */ -#define PI_ERR_STATUS1_B 0x000460 /* Error Status 1B */ -#define PI_ERR_STATUS1_B_RCLR 0x000468 /* Error Status 1B clear on read */ -#define PI_SPOOL_CMP_A 0x000470 /* Spool compare for CPU A */ -#define PI_SPOOL_CMP_B 0x000478 /* Spool compare for CPU B */ -#define PI_CRB_TIMEOUT_A 0x000480 /* Timed out CRB entries for A */ -#define PI_CRB_TIMEOUT_B 0x000488 /* Timed out CRB entries for B */ -#define PI_SYSAD_ERRCHK_EN 0x000490 /* Enables SYSAD error checking */ -#define PI_BAD_CHECK_BIT_A 0x000498 /* Force SYSAD check bit error */ -#define PI_BAD_CHECK_BIT_B 0x0004a0 /* Force SYSAD check bit error */ -#define PI_NACK_CNT_A 0x0004a8 /* Consecutive NACK counter */ -#define PI_NACK_CNT_B 0x0004b0 /* " " for CPU B */ -#define PI_NACK_CMP 0x0004b8 /* NACK count compare */ -#define PI_STACKADDR_OFFSET (PI_ERR_STACK_ADDR_B - PI_ERR_STACK_ADDR_A) -#define PI_ERRSTAT_OFFSET (PI_ERR_STATUS0_B - PI_ERR_STATUS0_A) -#define PI_RDCLR_OFFSET (PI_ERR_STATUS0_A_RCLR - PI_ERR_STATUS0_A) - -/* Bits in PI_ERR_INT_PEND */ -#define PI_ERR_SPOOL_CMP_B 0x00000001 /* Spool end hit high water */ -#define PI_ERR_SPOOL_CMP_A 0x00000002 -#define PI_ERR_SPUR_MSG_B 0x00000004 /* Spurious message intr. */ -#define PI_ERR_SPUR_MSG_A 0x00000008 -#define PI_ERR_WRB_TERR_B 0x00000010 /* WRB TERR */ -#define PI_ERR_WRB_TERR_A 0x00000020 -#define PI_ERR_WRB_WERR_B 0x00000040 /* WRB WERR */ -#define PI_ERR_WRB_WERR_A 0x00000080 -#define PI_ERR_SYSSTATE_B 0x00000100 /* SysState parity error */ -#define PI_ERR_SYSSTATE_A 0x00000200 -#define PI_ERR_SYSAD_DATA_B 0x00000400 /* SysAD data parity error */ -#define PI_ERR_SYSAD_DATA_A 0x00000800 -#define PI_ERR_SYSAD_ADDR_B 0x00001000 /* SysAD addr parity error */ -#define PI_ERR_SYSAD_ADDR_A 0x00002000 -#define PI_ERR_SYSCMD_DATA_B 0x00004000 /* SysCmd data parity error */ -#define PI_ERR_SYSCMD_DATA_A 0x00008000 -#define PI_ERR_SYSCMD_ADDR_B 0x00010000 /* SysCmd addr parity error */ -#define PI_ERR_SYSCMD_ADDR_A 0x00020000 -#define PI_ERR_BAD_SPOOL_B 0x00040000 /* Error spooling to memory */ -#define PI_ERR_BAD_SPOOL_A 0x00080000 -#define PI_ERR_UNCAC_UNCORR_B 0x00100000 /* Uncached uncorrectable */ -#define PI_ERR_UNCAC_UNCORR_A 0x00200000 -#define PI_ERR_SYSSTATE_TAG_B 0x00400000 /* SysState tag parity error */ -#define PI_ERR_SYSSTATE_TAG_A 0x00800000 -#define PI_ERR_MD_UNCORR 0x01000000 /* Must be cleared in MD */ - -#define PI_ERR_CLEAR_ALL_A 0x00aaaaaa -#define PI_ERR_CLEAR_ALL_B 0x00555555 - - -/* - * The following three macros define all possible error int pends. - */ - -#define PI_FATAL_ERR_CPU_A (PI_ERR_SYSSTATE_TAG_A | \ - PI_ERR_BAD_SPOOL_A | \ - PI_ERR_SYSCMD_ADDR_A | \ - PI_ERR_SYSCMD_DATA_A | \ - PI_ERR_SYSAD_ADDR_A | \ - PI_ERR_SYSAD_DATA_A | \ - PI_ERR_SYSSTATE_A) - -#define PI_MISC_ERR_CPU_A (PI_ERR_UNCAC_UNCORR_A | \ - PI_ERR_WRB_WERR_A | \ - PI_ERR_WRB_TERR_A | \ - PI_ERR_SPUR_MSG_A | \ - PI_ERR_SPOOL_CMP_A) - -#define PI_FATAL_ERR_CPU_B (PI_ERR_SYSSTATE_TAG_B | \ - PI_ERR_BAD_SPOOL_B | \ - PI_ERR_SYSCMD_ADDR_B | \ - PI_ERR_SYSCMD_DATA_B | \ - PI_ERR_SYSAD_ADDR_B | \ - PI_ERR_SYSAD_DATA_B | \ - PI_ERR_SYSSTATE_B) - -#define PI_MISC_ERR_CPU_B (PI_ERR_UNCAC_UNCORR_B | \ - PI_ERR_WRB_WERR_B | \ - PI_ERR_WRB_TERR_B | \ - PI_ERR_SPUR_MSG_B | \ - PI_ERR_SPOOL_CMP_B) - -#define PI_ERR_GENERIC (PI_ERR_MD_UNCORR) - -/* - * Error types for PI_ERR_STATUS0_[AB] and error stack: - * Use the write types if WRBRRB is 1 else use the read types - */ - -/* Fields in PI_ERR_STATUS0_[AB] */ -#define PI_ERR_ST0_TYPE_MASK 0x0000000000000007 -#define PI_ERR_ST0_TYPE_SHFT 0 -#define PI_ERR_ST0_REQNUM_MASK 0x0000000000000038 -#define PI_ERR_ST0_REQNUM_SHFT 3 -#define PI_ERR_ST0_SUPPL_MASK 0x000000000001ffc0 -#define PI_ERR_ST0_SUPPL_SHFT 6 -#define PI_ERR_ST0_CMD_MASK 0x0000000001fe0000 -#define PI_ERR_ST0_CMD_SHFT 17 -#define PI_ERR_ST0_ADDR_MASK 0x3ffffffffe000000 -#define PI_ERR_ST0_ADDR_SHFT 25 -#define PI_ERR_ST0_OVERRUN_MASK 0x4000000000000000 -#define PI_ERR_ST0_OVERRUN_SHFT 62 -#define PI_ERR_ST0_VALID_MASK 0x8000000000000000 -#define PI_ERR_ST0_VALID_SHFT 63 - -/* Fields in PI_ERR_STATUS1_[AB] */ -#define PI_ERR_ST1_SPOOL_MASK 0x00000000001fffff -#define PI_ERR_ST1_SPOOL_SHFT 0 -#define PI_ERR_ST1_TOUTCNT_MASK 0x000000001fe00000 -#define PI_ERR_ST1_TOUTCNT_SHFT 21 -#define PI_ERR_ST1_INVCNT_MASK 0x0000007fe0000000 -#define PI_ERR_ST1_INVCNT_SHFT 29 -#define PI_ERR_ST1_CRBNUM_MASK 0x0000038000000000 -#define PI_ERR_ST1_CRBNUM_SHFT 39 -#define PI_ERR_ST1_WRBRRB_MASK 0x0000040000000000 -#define PI_ERR_ST1_WRBRRB_SHFT 42 -#define PI_ERR_ST1_CRBSTAT_MASK 0x001ff80000000000 -#define PI_ERR_ST1_CRBSTAT_SHFT 43 -#define PI_ERR_ST1_MSGSRC_MASK 0xffe0000000000000 -#define PI_ERR_ST1_MSGSRC_SHFT 53 - -/* Fields in the error stack */ -#define PI_ERR_STK_TYPE_MASK 0x0000000000000003 -#define PI_ERR_STK_TYPE_SHFT 0 -#define PI_ERR_STK_SUPPL_MASK 0x0000000000000038 -#define PI_ERR_STK_SUPPL_SHFT 3 -#define PI_ERR_STK_REQNUM_MASK 0x00000000000001c0 -#define PI_ERR_STK_REQNUM_SHFT 6 -#define PI_ERR_STK_CRBNUM_MASK 0x0000000000000e00 -#define PI_ERR_STK_CRBNUM_SHFT 9 -#define PI_ERR_STK_WRBRRB_MASK 0x0000000000001000 -#define PI_ERR_STK_WRBRRB_SHFT 12 -#define PI_ERR_STK_CRBSTAT_MASK 0x00000000007fe000 -#define PI_ERR_STK_CRBSTAT_SHFT 13 -#define PI_ERR_STK_CMD_MASK 0x000000007f800000 -#define PI_ERR_STK_CMD_SHFT 23 -#define PI_ERR_STK_ADDR_MASK 0xffffffff80000000 -#define PI_ERR_STK_ADDR_SHFT 31 - -/* Error type in the error status or stack on Read CRBs */ -#define PI_ERR_RD_PRERR 1 -#define PI_ERR_RD_DERR 2 -#define PI_ERR_RD_TERR 3 - -/* Error type in the error status or stack on Write CRBs */ -#define PI_ERR_WR_WERR 0 -#define PI_ERR_WR_PWERR 1 -#define PI_ERR_WR_TERR 3 - -/* Read or Write CRB in error status or stack */ -#define PI_ERR_RRB 0 -#define PI_ERR_WRB 1 -#define PI_ERR_ANY_CRB 2 - -/* Address masks in the error status and error stack are not the same */ -#define ERR_STK_ADDR_SHFT 7 -#define ERR_STAT0_ADDR_SHFT 3 - -#define PI_MIN_STACK_SIZE 4096 /* For figuring out the size to set */ -#define PI_STACK_SIZE_SHFT 12 /* 4k */ - -#define ERR_STACK_SIZE_BYTES(_sz) \ - ((_sz) ? (PI_MIN_STACK_SIZE << ((_sz) - 1)) : 0) - -#ifndef __ASSEMBLY__ -/* - * format of error stack and error status registers. - */ - -struct err_stack_format { - u64 sk_addr : 33, /* address */ - sk_cmd : 8, /* message command */ - sk_crb_sts : 10, /* status from RRB or WRB */ - sk_rw_rb : 1, /* RRB == 0, WRB == 1 */ - sk_crb_num : 3, /* WRB (0 to 7) or RRB (0 to 4) */ - sk_t5_req : 3, /* RRB T5 request number */ - sk_suppl : 3, /* lowest 3 bit of supplemental */ - sk_err_type: 3; /* error type */ -}; - -typedef union pi_err_stack { - u64 pi_stk_word; - struct err_stack_format pi_stk_fmt; -} pi_err_stack_t; - -struct err_status0_format { - u64 s0_valid : 1, /* Valid */ - s0_ovr_run : 1, /* Overrun, spooled to memory */ - s0_addr : 37, /* address */ - s0_cmd : 8, /* message command */ - s0_supl : 11, /* message supplemental field */ - s0_t5_req : 3, /* RRB T5 request number */ - s0_err_type: 3; /* error type */ -}; - -typedef union pi_err_stat0 { - u64 pi_stat0_word; - struct err_status0_format pi_stat0_fmt; -} pi_err_stat0_t; - -struct err_status1_format { - u64 s1_src : 11, /* message source */ - s1_crb_sts : 10, /* status from RRB or WRB */ - s1_rw_rb : 1, /* RRB == 0, WRB == 1 */ - s1_crb_num : 3, /* WRB (0 to 7) or RRB (0 to 4) */ - s1_inval_cnt:10, /* signed invalidate counter RRB */ - s1_to_cnt : 8, /* crb timeout counter */ - s1_spl_cnt : 21; /* number spooled to memory */ -}; - -typedef union pi_err_stat1 { - u64 pi_stat1_word; - struct err_status1_format pi_stat1_fmt; -} pi_err_stat1_t; - -typedef u64 rtc_time_t; - -#endif /* !__ASSEMBLY__ */ - - -/* Bits in PI_SYSAD_ERRCHK_EN */ -#define PI_SYSAD_ERRCHK_ECCGEN 0x01 /* Enable ECC generation */ -#define PI_SYSAD_ERRCHK_QUALGEN 0x02 /* Enable data quality signal gen. */ -#define PI_SYSAD_ERRCHK_SADP 0x04 /* Enable SysAD parity checking */ -#define PI_SYSAD_ERRCHK_CMDP 0x08 /* Enable SysCmd parity checking */ -#define PI_SYSAD_ERRCHK_STATE 0x10 /* Enable SysState parity checking */ -#define PI_SYSAD_ERRCHK_QUAL 0x20 /* Enable data quality checking */ -#define PI_SYSAD_CHECK_ALL 0x3f /* Generate and check all signals. */ - -/* Interrupt pending bits on R10000 */ - -#define HUB_IP_PEND0 0x0400 -#define HUB_IP_PEND1_CC 0x0800 -#define HUB_IP_RT 0x1000 -#define HUB_IP_PROF 0x2000 -#define HUB_IP_ERROR 0x4000 -#define HUB_IP_MASK 0x7c00 - -/* PI_RT_LOCAL_CTRL mask and shift definitions */ - -#define PRLC_USE_INT_SHFT 16 -#define PRLC_USE_INT_MASK (UINT64_CAST 1 << 16) -#define PRLC_USE_INT (UINT64_CAST 1 << 16) -#define PRLC_GCLK_SHFT 15 -#define PRLC_GCLK_MASK (UINT64_CAST 1 << 15) -#define PRLC_GCLK (UINT64_CAST 1 << 15) -#define PRLC_GCLK_COUNT_SHFT 8 -#define PRLC_GCLK_COUNT_MASK (UINT64_CAST 0x7f << 8) -#define PRLC_MAX_COUNT_SHFT 1 -#define PRLC_MAX_COUNT_MASK (UINT64_CAST 0x7f << 1) -#define PRLC_GCLK_EN_SHFT 0 -#define PRLC_GCLK_EN_MASK (UINT64_CAST 1) -#define PRLC_GCLK_EN (UINT64_CAST 1) - -/* PI_RT_FILTER_CTRL mask and shift definitions */ - -/* - * Bits for NACK_CNT_A/B and NACK_CMP - */ -#define PI_NACK_CNT_EN_SHFT 20 -#define PI_NACK_CNT_EN_MASK 0x100000 -#define PI_NACK_CNT_MASK 0x0fffff -#define PI_NACK_CNT_MAX 0x0fffff - -#endif /* _ASM_SN_SN0_HUBPI_H */ diff --git a/include/asm-mips/sn/sn0/ip27.h b/include/asm-mips/sn/sn0/ip27.h deleted file mode 100644 index 3c97e0855c8d..000000000000 --- a/include/asm-mips/sn/sn0/ip27.h +++ /dev/null @@ -1,85 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/IP27.h>. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999, 2006 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_IP27_H -#define _ASM_SN_SN0_IP27_H - -#include <asm/mipsregs.h> - -/* - * Simple definitions for the masks which remove SW bits from pte. - */ - -#define TLBLO_HWBITSHIFT 0 /* Shift value, for masking */ - -#ifndef __ASSEMBLY__ - -#define CAUSE_BERRINTR IE_IRQ5 - -#define ECCF_CACHE_ERR 0 -#define ECCF_TAGLO 1 -#define ECCF_ECC 2 -#define ECCF_ERROREPC 3 -#define ECCF_PADDR 4 -#define ECCF_SIZE (5 * sizeof(long)) - -#endif /* !__ASSEMBLY__ */ - -#ifdef __ASSEMBLY__ - -/* - * KL_GET_CPUNUM (similar to EV_GET_SPNUM for EVEREST platform) reads - * the processor number of the calling processor. The proc parameters - * must be a register. - */ -#define KL_GET_CPUNUM(proc) \ - dli proc, LOCAL_HUB(0); \ - ld proc, PI_CPU_NUM(proc) - -#endif /* __ASSEMBLY__ */ - -/* - * R10000 status register interrupt bit mask usage for IP27. - */ -#define SRB_SWTIMO IE_SW0 /* 0x0100 */ -#define SRB_NET IE_SW1 /* 0x0200 */ -#define SRB_DEV0 IE_IRQ0 /* 0x0400 */ -#define SRB_DEV1 IE_IRQ1 /* 0x0800 */ -#define SRB_TIMOCLK IE_IRQ2 /* 0x1000 */ -#define SRB_PROFCLK IE_IRQ3 /* 0x2000 */ -#define SRB_ERR IE_IRQ4 /* 0x4000 */ -#define SRB_SCHEDCLK IE_IRQ5 /* 0x8000 */ - -#define SR_IBIT_HI SRB_DEV0 -#define SR_IBIT_PROF SRB_PROFCLK - -#define SRB_SWTIMO_IDX 0 -#define SRB_NET_IDX 1 -#define SRB_DEV0_IDX 2 -#define SRB_DEV1_IDX 3 -#define SRB_TIMOCLK_IDX 4 -#define SRB_PROFCLK_IDX 5 -#define SRB_ERR_IDX 6 -#define SRB_SCHEDCLK_IDX 7 - -#define NUM_CAUSE_INTRS 8 - -#define SCACHE_LINESIZE 128 -#define SCACHE_LINEMASK (SCACHE_LINESIZE - 1) - -#include <asm/sn/addrs.h> - -#define LED_CYCLE_MASK 0x0f -#define LED_CYCLE_SHFT 4 - -#define SEND_NMI(_nasid, _slice) \ - REMOTE_HUB_S((_nasid), (PI_NMI_A + ((_slice) * PI_NMI_OFFSET)), 1) - -#endif /* _ASM_SN_SN0_IP27_H */ |
