diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/ata/pata_via.c | 94 |
1 files changed, 76 insertions, 18 deletions
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c index c5f1616d224d..489bd5796e73 100644 --- a/drivers/ata/pata_via.c +++ b/drivers/ata/pata_via.c @@ -60,7 +60,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_via" -#define DRV_VERSION "0.1.14" +#define DRV_VERSION "0.2.0" /* * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx @@ -297,6 +297,8 @@ static struct scsi_host_template via_sht = { .slave_configure = ata_scsi_slave_config, .slave_destroy = ata_scsi_slave_destroy, .bios_param = ata_std_bios_param, + .resume = ata_scsi_device_resume, + .suspend = ata_scsi_device_suspend, }; static struct ata_port_operations via_port_ops = { @@ -370,8 +372,42 @@ static struct ata_port_operations via_port_ops_noirq = { }; /** + * via_config_fifo - set up the FIFO + * @pdev: PCI device + * @flags: configuration flags + * + * Set the FIFO properties for this device if neccessary. Used both on + * set up and on and the resume path + */ + +static void via_config_fifo(struct pci_dev *pdev, unsigned int flags) +{ + u8 enable; + + /* 0x40 low bits indicate enabled channels */ + pci_read_config_byte(pdev, 0x40 , &enable); + enable &= 3; + + if (flags & VIA_SET_FIFO) { + u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; + u8 fifo; + + pci_read_config_byte(pdev, 0x43, &fifo); + + /* Clear PREQ# until DDACK# for errata */ + if (flags & VIA_BAD_PREQ) + fifo &= 0x7F; + else + fifo &= 0x9f; + /* Turn on FIFO for enabled channels */ + fifo |= fifo_setting[enable]; + pci_write_config_byte(pdev, 0x43, fifo); + } +} + +/** * via_init_one - discovery callback - * @pdev: PCI device ID + * @pdev: PCI device * @id: PCI table info * * A VIA IDE interface has been discovered. Figure out what revision @@ -471,21 +507,8 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) } /* Initialise the FIFO for the enabled channels. */ - if (config->flags & VIA_SET_FIFO) { - u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; - u8 fifo; - - pci_read_config_byte(pdev, 0x43, &fifo); - - /* Clear PREQ# until DDACK# for errata */ - if (config->flags & VIA_BAD_PREQ) - fifo &= 0x7F; - else - fifo &= 0x9f; - /* Turn on FIFO for enabled channels */ - fifo |= fifo_setting[enable]; - pci_write_config_byte(pdev, 0x43, fifo); - } + via_config_fifo(pdev, config->flags); + /* Clock set up */ switch(config->flags & VIA_UDMA) { case VIA_UDMA_NONE: @@ -529,6 +552,39 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) return ata_pci_init_one(pdev, port_info, 2); } +/** + * via_reinit_one - reinit after resume + * @pdev; PCI device + * + * Called when the VIA PATA device is resumed. We must then + * reconfigure the fifo and other setup we may have altered. In + * addition the kernel needs to have the resume methods on PCI + * quirk supported. + */ + +static int via_reinit_one(struct pci_dev *pdev) +{ + u32 timing; + struct ata_host *host = dev_get_drvdata(&pdev->dev); + const struct via_isa_bridge *config = host->private_data; + + via_config_fifo(pdev, config->flags); + + if ((config->flags & VIA_UDMA) == VIA_UDMA_66) { + /* The 66 MHz devices require we enable the clock */ + pci_read_config_dword(pdev, 0x50, &timing); + timing |= 0x80008; + pci_write_config_dword(pdev, 0x50, timing); + } + if (config->flags & VIA_BAD_CLK66) { + /* Disable the 66MHz clock on problem devices */ + pci_read_config_dword(pdev, 0x50, &timing); + timing &= ~0x80008; + pci_write_config_dword(pdev, 0x50, timing); + } + return ata_pci_device_resume(pdev); +} + static const struct pci_device_id via[] = { { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C576_1), }, { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C586_1), }, @@ -542,7 +598,9 @@ static struct pci_driver via_pci_driver = { .name = DRV_NAME, .id_table = via, .probe = via_init_one, - .remove = ata_pci_remove_one + .remove = ata_pci_remove_one, + .suspend = ata_pci_device_suspend, + .resume = via_reinit_one, }; static int __init via_init(void) |
