diff options
Diffstat (limited to 'drivers/video/bfin-lq035q1-fb.c')
-rw-r--r-- | drivers/video/bfin-lq035q1-fb.c | 252 |
1 files changed, 146 insertions, 106 deletions
diff --git a/drivers/video/bfin-lq035q1-fb.c b/drivers/video/bfin-lq035q1-fb.c index 2baac7cc1425..c8e1f04941bd 100644 --- a/drivers/video/bfin-lq035q1-fb.c +++ b/drivers/video/bfin-lq035q1-fb.c @@ -61,47 +61,13 @@ #define LCD_X_RES 320 /* Horizontal Resolution */ #define LCD_Y_RES 240 /* Vertical Resolution */ #define DMA_BUS_SIZE 16 +#define U_LINE 4 /* Blanking Lines */ -#define USE_RGB565_16_BIT_PPI - -#ifdef USE_RGB565_16_BIT_PPI -#define LCD_BPP 16 /* Bit Per Pixel */ -#define CLOCKS_PER_PIX 1 -#define CPLD_PIPELINE_DELAY_COR 0 /* NO CPLB */ -#endif /* Interface 16/18-bit TFT over an 8-bit wide PPI using a small Programmable Logic Device (CPLD) * http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165 */ -#ifdef USE_RGB565_8_BIT_PPI -#define LCD_BPP 16 /* Bit Per Pixel */ -#define CLOCKS_PER_PIX 2 -#define CPLD_PIPELINE_DELAY_COR 3 /* RGB565 */ -#endif - -#ifdef USE_RGB888_8_BIT_PPI -#define LCD_BPP 24 /* Bit Per Pixel */ -#define CLOCKS_PER_PIX 3 -#define CPLD_PIPELINE_DELAY_COR 5 /* RGB888 */ -#endif - - /* - * HS and VS timing parameters (all in number of PPI clk ticks) - */ - -#define U_LINE 4 /* Blanking Lines */ - -#define H_ACTPIX (LCD_X_RES * CLOCKS_PER_PIX) /* active horizontal pixel */ -#define H_PERIOD (336 * CLOCKS_PER_PIX) /* HS period */ -#define H_PULSE (2 * CLOCKS_PER_PIX) /* HS pulse width */ -#define H_START (7 * CLOCKS_PER_PIX + CPLD_PIPELINE_DELAY_COR) /* first valid pixel */ - -#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */ -#define V_PULSE (2 * CLOCKS_PER_PIX) /* VS pulse width (1-5 H_PERIODs) */ -#define V_PERIOD (H_PERIOD * V_LINES) /* VS period */ - -#define ACTIVE_VIDEO_MEM_OFFSET ((U_LINE / 2) * LCD_X_RES * (LCD_BPP / 8)) #define BFIN_LCD_NBR_PALETTE_ENTRIES 256 @@ -110,12 +76,6 @@ #define PPI_PORT_CFG_01 0x10 #define PPI_POLS_1 0x8000 -#if (CLOCKS_PER_PIX > 1) -#define PPI_PMODE (DLEN_8 | PACK_EN) -#else -#define PPI_PMODE (DLEN_16) -#endif - #define LQ035_INDEX 0x74 #define LQ035_DATA 0x76 @@ -139,6 +99,15 @@ struct bfin_lq035q1fb_info { int irq; spinlock_t lock; /* lock */ u32 pseudo_pal[16]; + + u32 lcd_bpp; + u32 h_actpix; + u32 h_period; + u32 h_pulse; + u32 h_start; + u32 v_lines; + u32 v_pulse; + u32 v_period; }; static int nocursor; @@ -234,16 +203,69 @@ static int lq035q1_backlight(struct bfin_lq035q1fb_info *info, unsigned arg) return 0; } +static int bfin_lq035q1_calc_timing(struct bfin_lq035q1fb_info *fbi) +{ + unsigned long clocks_per_pix, cpld_pipeline_delay_cor; + + /* + * Interface 16/18-bit TFT over an 8-bit wide PPI using a small + * Programmable Logic Device (CPLD) + * http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165 + */ + + switch (fbi->disp_info->ppi_mode) { + case USE_RGB565_16_BIT_PPI: + fbi->lcd_bpp = 16; + clocks_per_pix = 1; + cpld_pipeline_delay_cor = 0; + break; + case USE_RGB565_8_BIT_PPI: + fbi->lcd_bpp = 16; + clocks_per_pix = 2; + cpld_pipeline_delay_cor = 3; + break; + case USE_RGB888_8_BIT_PPI: + fbi->lcd_bpp = 24; + clocks_per_pix = 3; + cpld_pipeline_delay_cor = 5; + break; + default: + return -EINVAL; + } + + /* + * HS and VS timing parameters (all in number of PPI clk ticks) + */ + + fbi->h_actpix = (LCD_X_RES * clocks_per_pix); /* active horizontal pixel */ + fbi->h_period = (336 * clocks_per_pix); /* HS period */ + fbi->h_pulse = (2 * clocks_per_pix); /* HS pulse width */ + fbi->h_start = (7 * clocks_per_pix + cpld_pipeline_delay_cor); /* first valid pixel */ + + fbi->v_lines = (LCD_Y_RES + U_LINE); /* total vertical lines */ + fbi->v_pulse = (2 * clocks_per_pix); /* VS pulse width (1-5 H_PERIODs) */ + fbi->v_period = (fbi->h_period * fbi->v_lines); /* VS period */ + + return 0; +} + static void bfin_lq035q1_config_ppi(struct bfin_lq035q1fb_info *fbi) { - bfin_write_PPI_DELAY(H_START); - bfin_write_PPI_COUNT(H_ACTPIX - 1); - bfin_write_PPI_FRAME(V_LINES); + unsigned ppi_pmode; + + if (fbi->disp_info->ppi_mode == USE_RGB565_16_BIT_PPI) + ppi_pmode = DLEN_16; + else + ppi_pmode = (DLEN_8 | PACK_EN); + + bfin_write_PPI_DELAY(fbi->h_start); + bfin_write_PPI_COUNT(fbi->h_actpix - 1); + bfin_write_PPI_FRAME(fbi->v_lines); bfin_write_PPI_CONTROL(PPI_TX_MODE | /* output mode , PORT_DIR */ PPI_XFER_TYPE_11 | /* sync mode XFR_TYPE */ PPI_PORT_CFG_01 | /* two frame sync PORT_CFG */ - PPI_PMODE | /* 8/16 bit data length / PACK_EN? */ + ppi_pmode | /* 8/16 bit data length / PACK_EN? */ PPI_POLS_1); /* faling edge syncs POLS */ } @@ -272,19 +294,19 @@ static void bfin_lq035q1_stop_timers(void) } -static void bfin_lq035q1_init_timers(void) +static void bfin_lq035q1_init_timers(struct bfin_lq035q1fb_info *fbi) { bfin_lq035q1_stop_timers(); - set_gptimer_period(TIMER_HSYNC_id, H_PERIOD); - set_gptimer_pwidth(TIMER_HSYNC_id, H_PULSE); + set_gptimer_period(TIMER_HSYNC_id, fbi->h_period); + set_gptimer_pwidth(TIMER_HSYNC_id, fbi->h_pulse); set_gptimer_config(TIMER_HSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT | TIMER_TIN_SEL | TIMER_CLK_SEL| TIMER_EMU_RUN); - set_gptimer_period(TIMER_VSYNC_id, V_PERIOD); - set_gptimer_pwidth(TIMER_VSYNC_id, V_PULSE); + set_gptimer_period(TIMER_VSYNC_id, fbi->v_period); + set_gptimer_pwidth(TIMER_VSYNC_id, fbi->v_pulse); set_gptimer_config(TIMER_VSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT | TIMER_TIN_SEL | TIMER_CLK_SEL | TIMER_EMU_RUN); @@ -294,21 +316,21 @@ static void bfin_lq035q1_init_timers(void) static void bfin_lq035q1_config_dma(struct bfin_lq035q1fb_info *fbi) { + set_dma_config(CH_PPI, set_bfin_dma_config(DIR_READ, DMA_FLOW_AUTO, INTR_DISABLE, DIMENSION_2D, DATA_SIZE_16, DMA_NOSYNC_KEEP_DMA_BUF)); - set_dma_x_count(CH_PPI, (LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE); + set_dma_x_count(CH_PPI, (LCD_X_RES * fbi->lcd_bpp) / DMA_BUS_SIZE); set_dma_x_modify(CH_PPI, DMA_BUS_SIZE / 8); - set_dma_y_count(CH_PPI, V_LINES); + set_dma_y_count(CH_PPI, fbi->v_lines); set_dma_y_modify(CH_PPI, DMA_BUS_SIZE / 8); set_dma_start_addr(CH_PPI, (unsigned long)fbi->fb_buffer); } -#if (CLOCKS_PER_PIX == 1) static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2, P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3, P_PPI0_D4, P_PPI0_D5, @@ -316,22 +338,27 @@ static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2, P_PPI0_D9, P_PPI0_D10, P_PPI0_D11, P_PPI0_D12, P_PPI0_D13, P_PPI0_D14, P_PPI0_D15, 0}; -#else -static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2, + +static const u16 ppi0_req_8[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2, P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3, P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7, 0}; -#endif -static inline void bfin_lq035q1_free_ports(void) +static inline void bfin_lq035q1_free_ports(unsigned ppi16) { - peripheral_free_list(ppi0_req_16); + if (ppi16) + peripheral_free_list(ppi0_req_16); + else + peripheral_free_list(ppi0_req_8); + if (ANOMALY_05000400) gpio_free(P_IDENT(P_PPI0_FS3)); } -static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev) +static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev, + unsigned ppi16) { + int ret; /* ANOMALY_05000400 - PPI Does Not Start Properly In Specific Mode: * Drive PPI_FS3 Low */ @@ -342,7 +369,12 @@ static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev) gpio_direction_output(P_IDENT(P_PPI0_FS3), 0); } - if (peripheral_request_list(ppi0_req_16, DRIVER_NAME)) { + if (ppi16) + ret = peripheral_request_list(ppi0_req_16, DRIVER_NAME); + else + ret = peripheral_request_list(ppi0_req_8, DRIVER_NAME); + + if (ret) { dev_err(&pdev->dev, "requesting peripherals failed\n"); return -EFAULT; } @@ -364,7 +396,7 @@ static int bfin_lq035q1_fb_open(struct fb_info *info, int user) bfin_lq035q1_config_dma(fbi); bfin_lq035q1_config_ppi(fbi); - bfin_lq035q1_init_timers(); + bfin_lq035q1_init_timers(fbi); /* start dma */ enable_dma(CH_PPI); @@ -402,12 +434,9 @@ static int bfin_lq035q1_fb_release(struct fb_info *info, int user) static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info) { - switch (var->bits_per_pixel) { -#if (LCD_BPP == 24) - case 24:/* TRUECOLOUR, 16m */ -#else - case 16:/* DIRECTCOLOUR, 64k */ -#endif + struct bfin_lq035q1fb_info *fbi = info->par; + + if (var->bits_per_pixel == fbi->lcd_bpp) { var->red.offset = info->var.red.offset; var->green.offset = info->var.green.offset; var->blue.offset = info->var.blue.offset; @@ -420,8 +449,7 @@ static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var, var->red.msb_right = 0; var->green.msb_right = 0; var->blue.msb_right = 0; - break; - default: + } else { pr_debug("%s: depth not supported: %u BPP\n", __func__, var->bits_per_pixel); return -EINVAL; @@ -528,6 +556,7 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) { struct bfin_lq035q1fb_info *info; struct fb_info *fbinfo; + u32 active_video_mem_offset; int ret; ret = request_dma(CH_PPI, DRIVER_NAME"_CH_PPI"); @@ -550,6 +579,12 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) platform_set_drvdata(pdev, fbinfo); + ret = bfin_lq035q1_calc_timing(info); + if (ret < 0) { + dev_err(&pdev->dev, "Failed PPI Mode\n"); + goto out3; + } + strcpy(fbinfo->fix.id, DRIVER_NAME); fbinfo->fix.type = FB_TYPE_PACKED_PIXELS; @@ -571,46 +606,48 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) fbinfo->var.xres_virtual = LCD_X_RES; fbinfo->var.yres = LCD_Y_RES; fbinfo->var.yres_virtual = LCD_Y_RES; - fbinfo->var.bits_per_pixel = LCD_BPP; + fbinfo->var.bits_per_pixel = info->lcd_bpp; if (info->disp_info->mode & LQ035_BGR) { -#if (LCD_BPP == 24) - fbinfo->var.red.offset = 0; - fbinfo->var.green.offset = 8; - fbinfo->var.blue.offset = 16; -#else - fbinfo->var.red.offset = 0; - fbinfo->var.green.offset = 5; - fbinfo->var.blue.offset = 11; -#endif + if (info->lcd_bpp == 24) { + fbinfo->var.red.offset = 0; + fbinfo->var.green.offset = 8; + fbinfo->var.blue.offset = 16; + } else { + fbinfo->var.red.offset = 0; + fbinfo->var.green.offset = 5; + fbinfo->var.blue.offset = 11; + } } else { -#if (LCD_BPP == 24) - fbinfo->var.red.offset = 16; - fbinfo->var.green.offset = 8; - fbinfo->var.blue.offset = 0; -#else - fbinfo->var.red.offset = 11; - fbinfo->var.green.offset = 5; - fbinfo->var.blue.offset = 0; -#endif + if (info->lcd_bpp == 24) { + fbinfo->var.red.offset = 16; + fbinfo->var.green.offset = 8; + fbinfo->var.blue.offset = 0; + } else { + fbinfo->var.red.offset = 11; + fbinfo->var.green.offset = 5; + fbinfo->var.blue.offset = 0; + } } fbinfo->var.transp.offset = 0; -#if (LCD_BPP == 24) - fbinfo->var.red.length = 8; - fbinfo->var.green.length = 8; - fbinfo->var.blue.length = 8; -#else - fbinfo->var.red.length = 5; - fbinfo->var.green.length = 6; - fbinfo->var.blue.length = 5; -#endif + if (info->lcd_bpp == 24) { + fbinfo->var.red.length = 8; + fbinfo->var.green.length = 8; + fbinfo->var.blue.length = 8; + } else { + fbinfo->var.red.length = 5; + fbinfo->var.green.length = 6; + fbinfo->var.blue.length = 5; + } fbinfo->var.transp.length = 0; - fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * LCD_BPP / 8 - + ACTIVE_VIDEO_MEM_OFFSET; + active_video_mem_offset = ((U_LINE / 2) * LCD_X_RES * (info->lcd_bpp / 8)); + + fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * info->lcd_bpp / 8 + + active_video_mem_offset; fbinfo->fix.line_length = fbinfo->var.xres_virtual * fbinfo->var.bits_per_pixel / 8; @@ -629,8 +666,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) goto out3; } - fbinfo->screen_base = (void *)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET; - fbinfo->fix.smem_start = (int)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET; + fbinfo->screen_base = (void *)info->fb_buffer + active_video_mem_offset; + fbinfo->fix.smem_start = (int)info->fb_buffer + active_video_mem_offset; fbinfo->fbops = &bfin_lq035q1_fb_ops; @@ -643,7 +680,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) goto out4; } - ret = bfin_lq035q1_request_ports(pdev); + ret = bfin_lq035q1_request_ports(pdev, + info->disp_info->ppi_mode == USE_RGB565_16_BIT_PPI); if (ret) { dev_err(&pdev->dev, "couldn't request gpio port\n"); goto out6; @@ -693,7 +731,7 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) } dev_info(&pdev->dev, "%dx%d %d-bit RGB FrameBuffer initialized\n", - LCD_X_RES, LCD_Y_RES, LCD_BPP); + LCD_X_RES, LCD_Y_RES, info->lcd_bpp); return 0; @@ -705,7 +743,8 @@ static int __devinit bfin_lq035q1_probe(struct platform_device *pdev) out8: free_irq(info->irq, info); out7: - bfin_lq035q1_free_ports(); + bfin_lq035q1_free_ports(info->disp_info->ppi_mode == + USE_RGB565_16_BIT_PPI); out6: fb_dealloc_cmap(&fbinfo->cmap); out4: @@ -742,7 +781,8 @@ static int __devexit bfin_lq035q1_remove(struct platform_device *pdev) fb_dealloc_cmap(&fbinfo->cmap); - bfin_lq035q1_free_ports(); + bfin_lq035q1_free_ports(info->disp_info->ppi_mode == + USE_RGB565_16_BIT_PPI); platform_set_drvdata(pdev, NULL); framebuffer_release(fbinfo); @@ -781,7 +821,7 @@ static int bfin_lq035q1_resume(struct device *dev) bfin_lq035q1_config_dma(info); bfin_lq035q1_config_ppi(info); - bfin_lq035q1_init_timers(); + bfin_lq035q1_init_timers(info); /* start dma */ enable_dma(CH_PPI); |