diff options
Diffstat (limited to 'drivers/usb/host')
| -rw-r--r-- | drivers/usb/host/ehci-fsl.c | 7 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-hcd.c | 9 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-omap.c | 39 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-pci.c | 8 | ||||
| -rw-r--r-- | drivers/usb/host/ehci-tegra.c | 377 | ||||
| -rw-r--r-- | drivers/usb/host/ohci-at91.c | 12 |
6 files changed, 259 insertions, 193 deletions
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 3e7345172e03..d0a84bd3f3eb 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -218,6 +218,9 @@ static void ehci_fsl_setup_phy(struct ehci_hcd *ehci, u32 portsc; struct usb_hcd *hcd = ehci_to_hcd(ehci); void __iomem *non_ehci = hcd->regs; + struct fsl_usb2_platform_data *pdata; + + pdata = hcd->self.controller->platform_data; portsc = ehci_readl(ehci, &ehci->regs->port_status[port_offset]); portsc &= ~(PORT_PTS_MSK | PORT_PTS_PTW); @@ -234,7 +237,9 @@ static void ehci_fsl_setup_phy(struct ehci_hcd *ehci, /* fall through */ case FSL_USB2_PHY_UTMI: /* enable UTMI PHY */ - setbits32(non_ehci + FSL_SOC_USB_CTRL, CTRL_UTMI_PHY_EN); + if (pdata->have_sysif_regs) + setbits32(non_ehci + FSL_SOC_USB_CTRL, + CTRL_UTMI_PHY_EN); portsc |= PORT_PTS_UTMI; break; case FSL_USB2_PHY_NONE: diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 806cc95317aa..4a3bc5b7a06f 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -858,8 +858,13 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) goto dead; } + /* + * We don't use STS_FLR, but some controllers don't like it to + * remain on, so mask it out along with the other status bits. + */ + masked_status = status & (INTR_MASK | STS_FLR); + /* Shared IRQ? */ - masked_status = status & INTR_MASK; if (!masked_status || unlikely(ehci->rh_state == EHCI_RH_HALTED)) { spin_unlock(&ehci->lock); return IRQ_NONE; @@ -910,7 +915,7 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) pcd_status = status; /* resume root hub? */ - if (!(cmd & CMD_RUN)) + if (ehci->rh_state == EHCI_RH_SUSPENDED) usb_hcd_resume_root_hub(hcd); /* get per-port change detect bits */ diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index bba9850f32f0..5c78f9e71466 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -42,6 +42,7 @@ #include <plat/usb.h> #include <linux/regulator/consumer.h> #include <linux/pm_runtime.h> +#include <linux/gpio.h> /* EHCI Register Set */ #define EHCI_INSNREG04 (0xA0) @@ -191,6 +192,19 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev) } } + if (pdata->phy_reset) { + if (gpio_is_valid(pdata->reset_gpio_port[0])) + gpio_request_one(pdata->reset_gpio_port[0], + GPIOF_OUT_INIT_LOW, "USB1 PHY reset"); + + if (gpio_is_valid(pdata->reset_gpio_port[1])) + gpio_request_one(pdata->reset_gpio_port[1], + GPIOF_OUT_INIT_LOW, "USB2 PHY reset"); + + /* Hold the PHY in RESET for enough time till DIR is high */ + udelay(10); + } + pm_runtime_enable(dev); pm_runtime_get_sync(dev); @@ -237,6 +251,19 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev) /* root ports should always stay powered */ ehci_port_power(omap_ehci, 1); + if (pdata->phy_reset) { + /* Hold the PHY in RESET for enough time till + * PHY is settled and ready + */ + udelay(10); + + if (gpio_is_valid(pdata->reset_gpio_port[0])) + gpio_set_value(pdata->reset_gpio_port[0], 1); + + if (gpio_is_valid(pdata->reset_gpio_port[1])) + gpio_set_value(pdata->reset_gpio_port[1], 1); + } + return 0; err_add_hcd: @@ -259,8 +286,9 @@ err_io: */ static int ehci_hcd_omap_remove(struct platform_device *pdev) { - struct device *dev = &pdev->dev; - struct usb_hcd *hcd = dev_get_drvdata(dev); + struct device *dev = &pdev->dev; + struct usb_hcd *hcd = dev_get_drvdata(dev); + struct ehci_hcd_omap_platform_data *pdata = dev->platform_data; usb_remove_hcd(hcd); disable_put_regulator(dev->platform_data); @@ -269,6 +297,13 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev) pm_runtime_put_sync(dev); pm_runtime_disable(dev); + if (pdata->phy_reset) { + if (gpio_is_valid(pdata->reset_gpio_port[0])) + gpio_free(pdata->reset_gpio_port[0]); + + if (gpio_is_valid(pdata->reset_gpio_port[1])) + gpio_free(pdata->reset_gpio_port[1]); + } return 0; } diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 01bb7241d6ef..fe8dc069164e 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -144,6 +144,14 @@ static int ehci_pci_setup(struct usb_hcd *hcd) hcd->has_tt = 1; tdi_reset(ehci); } + if (pdev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK) { + /* EHCI #1 or #2 on 6 Series/C200 Series chipset */ + if (pdev->device == 0x1c26 || pdev->device == 0x1c2d) { + ehci_info(ehci, "broken D3 during system sleep on ASUS\n"); + hcd->broken_pci_sleep = 1; + device_set_wakeup_capable(&pdev->dev, false); + } + } break; case PCI_VENDOR_ID_TDI: if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) { diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c index 73544bd440bd..f214a80cdee2 100644 --- a/drivers/usb/host/ehci-tegra.c +++ b/drivers/usb/host/ehci-tegra.c @@ -24,6 +24,7 @@ #include <linux/gpio.h> #include <linux/of.h> #include <linux/of_gpio.h> +#include <linux/pm_runtime.h> #include <mach/usb_phy.h> #include <mach/iomap.h> @@ -37,9 +38,7 @@ struct tegra_ehci_hcd { struct clk *emc_clk; struct usb_phy *transceiver; int host_resumed; - int bus_suspended; int port_resuming; - int power_down_on_bus_suspend; enum tegra_usb_phy_port_speed port_speed; }; @@ -273,120 +272,6 @@ static void tegra_ehci_restart(struct usb_hcd *hcd) up_write(&ehci_cf_port_reset_rwsem); } -static int tegra_usb_suspend(struct usb_hcd *hcd) -{ - struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); - struct ehci_regs __iomem *hw = tegra->ehci->regs; - unsigned long flags; - - spin_lock_irqsave(&tegra->ehci->lock, flags); - - tegra->port_speed = (readl(&hw->port_status[0]) >> 26) & 0x3; - ehci_halt(tegra->ehci); - clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); - - spin_unlock_irqrestore(&tegra->ehci->lock, flags); - - tegra_ehci_power_down(hcd); - return 0; -} - -static int tegra_usb_resume(struct usb_hcd *hcd) -{ - struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); - struct ehci_hcd *ehci = hcd_to_ehci(hcd); - struct ehci_regs __iomem *hw = ehci->regs; - unsigned long val; - - set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); - tegra_ehci_power_up(hcd); - - if (tegra->port_speed > TEGRA_USB_PHY_PORT_SPEED_HIGH) { - /* Wait for the phy to detect new devices - * before we restart the controller */ - msleep(10); - goto restart; - } - - /* Force the phy to keep data lines in suspend state */ - tegra_ehci_phy_restore_start(tegra->phy, tegra->port_speed); - - /* Enable host mode */ - tdi_reset(ehci); - - /* Enable Port Power */ - val = readl(&hw->port_status[0]); - val |= PORT_POWER; - writel(val, &hw->port_status[0]); - udelay(10); - - /* Check if the phy resume from LP0. When the phy resume from LP0 - * USB register will be reset. */ - if (!readl(&hw->async_next)) { - /* Program the field PTC based on the saved speed mode */ - val = readl(&hw->port_status[0]); - val &= ~PORT_TEST(~0); - if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_HIGH) - val |= PORT_TEST_FORCE; - else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_FULL) - val |= PORT_TEST(6); - else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) - val |= PORT_TEST(7); - writel(val, &hw->port_status[0]); - udelay(10); - - /* Disable test mode by setting PTC field to NORMAL_OP */ - val = readl(&hw->port_status[0]); - val &= ~PORT_TEST(~0); - writel(val, &hw->port_status[0]); - udelay(10); - } - - /* Poll until CCS is enabled */ - if (handshake(ehci, &hw->port_status[0], PORT_CONNECT, - PORT_CONNECT, 2000)) { - pr_err("%s: timeout waiting for PORT_CONNECT\n", __func__); - goto restart; - } - - /* Poll until PE is enabled */ - if (handshake(ehci, &hw->port_status[0], PORT_PE, - PORT_PE, 2000)) { - pr_err("%s: timeout waiting for USB_PORTSC1_PE\n", __func__); - goto restart; - } - - /* Clear the PCI status, to avoid an interrupt taken upon resume */ - val = readl(&hw->status); - val |= STS_PCD; - writel(val, &hw->status); - - /* Put controller in suspend mode by writing 1 to SUSP bit of PORTSC */ - val = readl(&hw->port_status[0]); - if ((val & PORT_POWER) && (val & PORT_PE)) { - val |= PORT_SUSPEND; - writel(val, &hw->port_status[0]); - - /* Wait until port suspend completes */ - if (handshake(ehci, &hw->port_status[0], PORT_SUSPEND, - PORT_SUSPEND, 1000)) { - pr_err("%s: timeout waiting for PORT_SUSPEND\n", - __func__); - goto restart; - } - } - - tegra_ehci_phy_restore_end(tegra->phy); - return 0; - -restart: - if (tegra->port_speed <= TEGRA_USB_PHY_PORT_SPEED_HIGH) - tegra_ehci_phy_restore_end(tegra->phy); - - tegra_ehci_restart(hcd); - return 0; -} - static void tegra_ehci_shutdown(struct usb_hcd *hcd) { struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); @@ -434,36 +319,6 @@ static int tegra_ehci_setup(struct usb_hcd *hcd) return retval; } -#ifdef CONFIG_PM -static int tegra_ehci_bus_suspend(struct usb_hcd *hcd) -{ - struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); - int error_status = 0; - - error_status = ehci_bus_suspend(hcd); - if (!error_status && tegra->power_down_on_bus_suspend) { - tegra_usb_suspend(hcd); - tegra->bus_suspended = 1; - } - - return error_status; -} - -static int tegra_ehci_bus_resume(struct usb_hcd *hcd) -{ - struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); - - if (tegra->bus_suspended && tegra->power_down_on_bus_suspend) { - tegra_usb_resume(hcd); - tegra->bus_suspended = 0; - } - - tegra_usb_phy_preresume(tegra->phy); - tegra->port_resuming = 1; - return ehci_bus_resume(hcd); -} -#endif - struct temp_buffer { void *kmalloc_ptr; void *old_xfer_buffer; @@ -574,8 +429,8 @@ static const struct hc_driver tegra_ehci_hc_driver = { .hub_control = tegra_ehci_hub_control, .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete, #ifdef CONFIG_PM - .bus_suspend = tegra_ehci_bus_suspend, - .bus_resume = tegra_ehci_bus_resume, + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, #endif .relinquish_port = ehci_relinquish_port, .port_handed_over = ehci_port_handed_over, @@ -603,11 +458,187 @@ static int setup_vbus_gpio(struct platform_device *pdev) dev_err(&pdev->dev, "can't enable vbus\n"); return err; } - gpio_set_value(gpio, 1); return err; } +#ifdef CONFIG_PM + +static int controller_suspend(struct device *dev) +{ + struct tegra_ehci_hcd *tegra = + platform_get_drvdata(to_platform_device(dev)); + struct ehci_hcd *ehci = tegra->ehci; + struct usb_hcd *hcd = ehci_to_hcd(ehci); + struct ehci_regs __iomem *hw = ehci->regs; + unsigned long flags; + + if (time_before(jiffies, ehci->next_statechange)) + msleep(10); + + spin_lock_irqsave(&ehci->lock, flags); + + tegra->port_speed = (readl(&hw->port_status[0]) >> 26) & 0x3; + ehci_halt(ehci); + clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + + spin_unlock_irqrestore(&ehci->lock, flags); + + tegra_ehci_power_down(hcd); + return 0; +} + +static int controller_resume(struct device *dev) +{ + struct tegra_ehci_hcd *tegra = + platform_get_drvdata(to_platform_device(dev)); + struct ehci_hcd *ehci = tegra->ehci; + struct usb_hcd *hcd = ehci_to_hcd(ehci); + struct ehci_regs __iomem *hw = ehci->regs; + unsigned long val; + + set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + tegra_ehci_power_up(hcd); + + if (tegra->port_speed > TEGRA_USB_PHY_PORT_SPEED_HIGH) { + /* Wait for the phy to detect new devices + * before we restart the controller */ + msleep(10); + goto restart; + } + + /* Force the phy to keep data lines in suspend state */ + tegra_ehci_phy_restore_start(tegra->phy, tegra->port_speed); + + /* Enable host mode */ + tdi_reset(ehci); + + /* Enable Port Power */ + val = readl(&hw->port_status[0]); + val |= PORT_POWER; + writel(val, &hw->port_status[0]); + udelay(10); + + /* Check if the phy resume from LP0. When the phy resume from LP0 + * USB register will be reset. */ + if (!readl(&hw->async_next)) { + /* Program the field PTC based on the saved speed mode */ + val = readl(&hw->port_status[0]); + val &= ~PORT_TEST(~0); + if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_HIGH) + val |= PORT_TEST_FORCE; + else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_FULL) + val |= PORT_TEST(6); + else if (tegra->port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) + val |= PORT_TEST(7); + writel(val, &hw->port_status[0]); + udelay(10); + + /* Disable test mode by setting PTC field to NORMAL_OP */ + val = readl(&hw->port_status[0]); + val &= ~PORT_TEST(~0); + writel(val, &hw->port_status[0]); + udelay(10); + } + + /* Poll until CCS is enabled */ + if (handshake(ehci, &hw->port_status[0], PORT_CONNECT, + PORT_CONNECT, 2000)) { + pr_err("%s: timeout waiting for PORT_CONNECT\n", __func__); + goto restart; + } + + /* Poll until PE is enabled */ + if (handshake(ehci, &hw->port_status[0], PORT_PE, + PORT_PE, 2000)) { + pr_err("%s: timeout waiting for USB_PORTSC1_PE\n", __func__); + goto restart; + } + + /* Clear the PCI status, to avoid an interrupt taken upon resume */ + val = readl(&hw->status); + val |= STS_PCD; + writel(val, &hw->status); + + /* Put controller in suspend mode by writing 1 to SUSP bit of PORTSC */ + val = readl(&hw->port_status[0]); + if ((val & PORT_POWER) && (val & PORT_PE)) { + val |= PORT_SUSPEND; + writel(val, &hw->port_status[0]); + + /* Wait until port suspend completes */ + if (handshake(ehci, &hw->port_status[0], PORT_SUSPEND, + PORT_SUSPEND, 1000)) { + pr_err("%s: timeout waiting for PORT_SUSPEND\n", + __func__); + goto restart; + } + } + + tegra_ehci_phy_restore_end(tegra->phy); + goto done; + + restart: + if (tegra->port_speed <= TEGRA_USB_PHY_PORT_SPEED_HIGH) + tegra_ehci_phy_restore_end(tegra->phy); + + tegra_ehci_restart(hcd); + + done: + tegra_usb_phy_preresume(tegra->phy); + tegra->port_resuming = 1; + return 0; +} + +static int tegra_ehci_suspend(struct device *dev) +{ + struct tegra_ehci_hcd *tegra = + platform_get_drvdata(to_platform_device(dev)); + struct usb_hcd *hcd = ehci_to_hcd(tegra->ehci); + int rc = 0; + + /* + * When system sleep is supported and USB controller wakeup is + * implemented: If the controller is runtime-suspended and the + * wakeup setting needs to be changed, call pm_runtime_resume(). + */ + if (HCD_HW_ACCESSIBLE(hcd)) + rc = controller_suspend(dev); + return rc; +} + +static int tegra_ehci_resume(struct device *dev) +{ + int rc; + + rc = controller_resume(dev); + if (rc == 0) { + pm_runtime_disable(dev); + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + } + return rc; +} + +static int tegra_ehci_runtime_suspend(struct device *dev) +{ + return controller_suspend(dev); +} + +static int tegra_ehci_runtime_resume(struct device *dev) +{ + return controller_resume(dev); +} + +static const struct dev_pm_ops tegra_ehci_pm_ops = { + .suspend = tegra_ehci_suspend, + .resume = tegra_ehci_resume, + .runtime_suspend = tegra_ehci_runtime_suspend, + .runtime_resume = tegra_ehci_runtime_resume, +}; + +#endif + static u64 tegra_ehci_dma_mask = DMA_BIT_MASK(32); static int tegra_ehci_probe(struct platform_device *pdev) @@ -722,7 +753,6 @@ static int tegra_ehci_probe(struct platform_device *pdev) } tegra->host_resumed = 1; - tegra->power_down_on_bus_suspend = pdata->power_down_on_bus_suspend; tegra->ehci = hcd_to_ehci(hcd); irq = platform_get_irq(pdev, 0); @@ -731,7 +761,6 @@ static int tegra_ehci_probe(struct platform_device *pdev) err = -ENODEV; goto fail; } - set_irq_flags(irq, IRQF_VALID); #ifdef CONFIG_USB_OTG_UTILS if (pdata->operating_mode == TEGRA_USB_OTG) { @@ -747,6 +776,14 @@ static int tegra_ehci_probe(struct platform_device *pdev) goto fail; } + pm_runtime_set_active(&pdev->dev); + pm_runtime_get_noresume(&pdev->dev); + + /* Don't skip the pm_runtime_forbid call if wakeup isn't working */ + /* if (!pdata->power_down_on_bus_suspend) */ + pm_runtime_forbid(&pdev->dev); + pm_runtime_enable(&pdev->dev); + pm_runtime_put_sync(&pdev->dev); return err; fail: @@ -773,33 +810,6 @@ fail_hcd: return err; } -#ifdef CONFIG_PM -static int tegra_ehci_resume(struct platform_device *pdev) -{ - struct tegra_ehci_hcd *tegra = platform_get_drvdata(pdev); - struct usb_hcd *hcd = ehci_to_hcd(tegra->ehci); - - if (tegra->bus_suspended) - return 0; - - return tegra_usb_resume(hcd); -} - -static int tegra_ehci_suspend(struct platform_device *pdev, pm_message_t state) -{ - struct tegra_ehci_hcd *tegra = platform_get_drvdata(pdev); - struct usb_hcd *hcd = ehci_to_hcd(tegra->ehci); - - if (tegra->bus_suspended) - return 0; - - if (time_before(jiffies, tegra->ehci->next_statechange)) - msleep(10); - - return tegra_usb_suspend(hcd); -} -#endif - static int tegra_ehci_remove(struct platform_device *pdev) { struct tegra_ehci_hcd *tegra = platform_get_drvdata(pdev); @@ -808,6 +818,10 @@ static int tegra_ehci_remove(struct platform_device *pdev) if (tegra == NULL || hcd == NULL) return -EINVAL; + pm_runtime_get_sync(&pdev->dev); + pm_runtime_disable(&pdev->dev); + pm_runtime_put_noidle(&pdev->dev); + #ifdef CONFIG_USB_OTG_UTILS if (tegra->transceiver) { otg_set_host(tegra->transceiver->otg, NULL); @@ -848,13 +862,12 @@ static struct of_device_id tegra_ehci_of_match[] __devinitdata = { static struct platform_driver tegra_ehci_driver = { .probe = tegra_ehci_probe, .remove = tegra_ehci_remove, -#ifdef CONFIG_PM - .suspend = tegra_ehci_suspend, - .resume = tegra_ehci_resume, -#endif .shutdown = tegra_ehci_hcd_shutdown, .driver = { .name = "tegra-ehci", .of_match_table = tegra_ehci_of_match, +#ifdef CONFIG_PM + .pm = &tegra_ehci_pm_ops, +#endif } }; diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index 09f597ad6e00..13ebeca8e73e 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -94,7 +94,7 @@ static void at91_stop_hc(struct platform_device *pdev) /*-------------------------------------------------------------------------*/ -static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); +static void __devexit usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); /* configure so an HC device and id are always provided */ /* always called with process context; sleeping is OK */ @@ -108,7 +108,7 @@ static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); * then invokes the start() method for the HCD associated with it * through the hotplug entry's driver_data. */ -static int usb_hcd_at91_probe(const struct hc_driver *driver, +static int __devinit usb_hcd_at91_probe(const struct hc_driver *driver, struct platform_device *pdev) { int retval; @@ -203,7 +203,7 @@ static int usb_hcd_at91_probe(const struct hc_driver *driver, * context, "rmmod" or something similar. * */ -static void usb_hcd_at91_remove(struct usb_hcd *hcd, +static void __devexit usb_hcd_at91_remove(struct usb_hcd *hcd, struct platform_device *pdev) { usb_remove_hcd(hcd); @@ -545,7 +545,7 @@ static int __devinit ohci_at91_of_init(struct platform_device *pdev) /*-------------------------------------------------------------------------*/ -static int ohci_hcd_at91_drv_probe(struct platform_device *pdev) +static int __devinit ohci_hcd_at91_drv_probe(struct platform_device *pdev) { struct at91_usbh_data *pdata; int i; @@ -620,7 +620,7 @@ static int ohci_hcd_at91_drv_probe(struct platform_device *pdev) return usb_hcd_at91_probe(&ohci_at91_hc_driver, pdev); } -static int ohci_hcd_at91_drv_remove(struct platform_device *pdev) +static int __devexit ohci_hcd_at91_drv_remove(struct platform_device *pdev) { struct at91_usbh_data *pdata = pdev->dev.platform_data; int i; @@ -696,7 +696,7 @@ MODULE_ALIAS("platform:at91_ohci"); static struct platform_driver ohci_hcd_at91_driver = { .probe = ohci_hcd_at91_drv_probe, - .remove = ohci_hcd_at91_drv_remove, + .remove = __devexit_p(ohci_hcd_at91_drv_remove), .shutdown = usb_hcd_platform_shutdown, .suspend = ohci_hcd_at91_drv_suspend, .resume = ohci_hcd_at91_drv_resume, |
