diff options
Diffstat (limited to 'drivers/usb/host/Kconfig')
| -rw-r--r-- | drivers/usb/host/Kconfig | 63 |
1 files changed, 30 insertions, 33 deletions
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 4263d011392c..5be0326aae38 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -29,15 +29,6 @@ if USB_XHCI_HCD config USB_XHCI_PLATFORM tristate -config USB_XHCI_HCD_DEBUGGING - bool "Debugging for the xHCI host controller" - ---help--- - Say 'Y' to turn on debugging for the xHCI host controller driver. - This will spew debugging output, even in interrupt context. - This should only be used for debugging xHCI driver bugs. - - If unsure, say N. - endif # USB_XHCI_HCD config USB_EHCI_HCD @@ -113,12 +104,6 @@ config USB_EHCI_HCD_PMC_MSP Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. If unsure, say N. -config USB_EHCI_BIG_ENDIAN_MMIO - bool - -config USB_EHCI_BIG_ENDIAN_DESC - bool - config XPS_USB_HCD_XILINX bool "Use Xilinx usb host EHCI controller core" depends on (PPC32 || MICROBLAZE) @@ -148,13 +133,11 @@ config USB_EHCI_MXC config USB_EHCI_HCD_OMAP tristate "EHCI support for OMAP3 and later chips" depends on ARCH_OMAP + select NOP_USB_XCEIV default y ---help--- Enables support for the on-chip EHCI controller on OMAP3 and later chips. - If your system uses a PHY on the USB port, you will need to - enable USB_PHY and the appropriate PHY driver as well. Most - boards need the NOP_USB_XCEIV PHY driver. config USB_EHCI_HCD_ORION tristate "Support for Marvell EBU on-chip EHCI USB controller" @@ -186,7 +169,6 @@ config USB_EHCI_HCD_AT91 config USB_EHCI_MSM tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" depends on ARCH_MSM - depends on USB_PHY select USB_EHCI_ROOT_HUB_TT select USB_MSM_OTG ---help--- @@ -354,6 +336,18 @@ config USB_FUSBH200_HCD To compile this driver as a module, choose M here: the module will be called fusbh200-hcd. +config USB_FOTG210_HCD + tristate "FOTG210 HCD support" + depends on USB + default N + ---help--- + Faraday FOTG210 is an OTG controller which can be configured as + an USB2.0 host. It is designed to meet USB2.0 EHCI specification + with minor modification. + + To compile this driver as a module, choose M here: the + module will be called fotg210-hcd. + config USB_OHCI_HCD tristate "OHCI HCD (USB 1.1) support" select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 @@ -497,20 +491,6 @@ config USB_OCTEON_OHCI controller. It is needed for low-speed USB 1.0 device support. All CN6XXX based chips with USB are supported. - -config USB_OHCI_BIG_ENDIAN_DESC - bool - default n - -config USB_OHCI_BIG_ENDIAN_MMIO - bool - default n - -config USB_OHCI_LITTLE_ENDIAN - bool - default n if STB03xxx || PPC_MPC52xx - default y - endif # USB_OHCI_HCD config USB_UHCI_HCD @@ -710,3 +690,20 @@ config USB_HCD_SSB for ehci and ohci. If unsure, say N. + +config USB_HCD_TEST_MODE + bool "HCD test mode support" + ---help--- + Say 'Y' to enable additional software test modes that may be + supported by the host controller drivers. + + One such test mode is the Embedded High-speed Host Electrical Test + (EHSET) for EHCI host controller hardware, specifically the "Single + Step Set Feature" test. Typically this will be enabled for On-the-Go + or embedded hosts that need to undergo USB-IF compliance testing with + the aid of special testing hardware. In the future, this may expand + to include other tests that require support from a HCD driver. + + This option is of interest only to developers who need to validate + their USB hardware designs. It is not needed for normal use. If + unsure, say N. |
