diff options
Diffstat (limited to 'drivers/serial')
52 files changed, 1230 insertions, 1498 deletions
diff --git a/drivers/serial/21285.c b/drivers/serial/21285.c index 7572665a8855..57438326b07f 100644 --- a/drivers/serial/21285.c +++ b/drivers/serial/21285.c @@ -7,7 +7,6 @@ * * $Id: 21285.c,v 1.37 2002/07/28 10:03:27 rmk Exp $ */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> @@ -479,7 +478,6 @@ static struct uart_driver serial21285_reg = { .owner = THIS_MODULE, .driver_name = "ttyFB", .dev_name = "ttyFB", - .devfs_name = "ttyFB", .major = SERIAL_21285_MAJOR, .minor = SERIAL_21285_MINOR, .nr = 1, diff --git a/drivers/serial/68328serial.c b/drivers/serial/68328serial.c index b88a7c1158af..993a702422ec 100644 --- a/drivers/serial/68328serial.c +++ b/drivers/serial/68328serial.c @@ -23,7 +23,6 @@ #include <linux/interrupt.h> #include <linux/tty.h> #include <linux/tty_flip.h> -#include <linux/config.h> #include <linux/major.h> #include <linux/string.h> #include <linux/fcntl.h> @@ -131,17 +130,6 @@ static int m68328_console_baud = CONSOLE_BAUD_RATE; static int m68328_console_cbaud = DEFAULT_CBAUD; -/* - * tmp_buf is used as a temporary buffer by serial_write. We need to - * lock it in case the memcpy_fromfs blocks while swapping in a page, - * and some other program tries to do a serial write at the same time. - * Since the lock will only come under contention when the system is - * swapping and available memory is low, it makes sense to share one - * buffer across all the serial ports, since it significantly saves - * memory if large numbers of serial ports are open. - */ -static unsigned char tmp_buf[SERIAL_XMIT_SIZE]; /* This is cheating */ - static inline int serial_paranoia_check(struct m68k_serial *info, char *name, const char *routine) { @@ -211,16 +199,16 @@ static void rs_stop(struct tty_struct *tty) if (serial_paranoia_check(info, tty->name, "rs_stop")) return; - save_flags(flags); cli(); + local_irq_save(flags); uart->ustcnt &= ~USTCNT_TXEN; - restore_flags(flags); + local_irq_restore(flags); } static void rs_put_char(char ch) { int flags, loops = 0; - save_flags(flags); cli(); + local_irq_save(flags); while (!(UTX & UTX_TX_AVAIL) && (loops < 1000)) { loops++; @@ -229,7 +217,7 @@ static void rs_put_char(char ch) UTX_TXDATA = ch; udelay(5); - restore_flags(flags); + local_irq_restore(flags); } static void rs_start(struct tty_struct *tty) @@ -241,7 +229,7 @@ static void rs_start(struct tty_struct *tty) if (serial_paranoia_check(info, tty->name, "rs_start")) return; - save_flags(flags); cli(); + local_irq_save(flags); if (info->xmit_cnt && info->xmit_buf && !(uart->ustcnt & USTCNT_TXEN)) { #ifdef USE_INTS uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK; @@ -249,7 +237,7 @@ static void rs_start(struct tty_struct *tty) uart->ustcnt |= USTCNT_TXEN; #endif } - restore_flags(flags); + local_irq_restore(flags); } /* Drop into either the boot monitor or kadb upon receiving a break @@ -327,14 +315,6 @@ static void receive_chars(struct m68k_serial *info, struct pt_regs *regs, if(!tty) goto clear_and_exit; - /* - * Make sure that we do not overflow the buffer - */ - if (tty_request_buffer_room(tty, 1) == 0) { - tty_schedule_flip(tty); - return; - } - flag = TTY_NORMAL; if(rx & URX_PARITY_ERROR) { @@ -473,7 +453,7 @@ static int startup(struct m68k_serial * info) return -ENOMEM; } - save_flags(flags); cli(); + local_irq_save(flags); /* * Clear the FIFO buffers and disable them @@ -506,7 +486,7 @@ static int startup(struct m68k_serial * info) change_speed(info); info->flags |= S_INITIALIZED; - restore_flags(flags); + local_irq_restore(flags); return 0; } @@ -523,7 +503,7 @@ static void shutdown(struct m68k_serial * info) if (!(info->flags & S_INITIALIZED)) return; - save_flags(flags); cli(); /* Disable interrupts */ + local_irq_save(flags); if (info->xmit_buf) { free_page((unsigned long) info->xmit_buf); @@ -534,7 +514,7 @@ static void shutdown(struct m68k_serial * info) set_bit(TTY_IO_ERROR, &info->tty->flags); info->flags &= ~S_INITIALIZED; - restore_flags(flags); + local_irq_restore(flags); } struct { @@ -655,24 +635,24 @@ static void rs_fair_output(void) if (info == 0) return; if (info->xmit_buf == 0) return; - save_flags(flags); cli(); + local_irq_save(flags); left = info->xmit_cnt; while (left != 0) { c = info->xmit_buf[info->xmit_tail]; info->xmit_tail = (info->xmit_tail+1) & (SERIAL_XMIT_SIZE-1); info->xmit_cnt--; - restore_flags(flags); + local_irq_restore(flags); rs_put_char(c); - save_flags(flags); cli(); + local_irq_save(flags); left = min(info->xmit_cnt, left-1); } /* Last character is being transmitted now (hopefully). */ udelay(5); - restore_flags(flags); + local_irq_restore(flags); return; } @@ -720,11 +700,11 @@ static void rs_flush_chars(struct tty_struct *tty) #endif /* Enable transmitter */ - save_flags(flags); cli(); + local_irq_save(flags); if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || !info->xmit_buf) { - restore_flags(flags); + local_irq_restore(flags); return; } @@ -749,7 +729,7 @@ static void rs_flush_chars(struct tty_struct *tty) while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5); } #endif - restore_flags(flags); + local_irq_restore(flags); } extern void console_printn(const char * b, int count); @@ -768,18 +748,22 @@ static int rs_write(struct tty_struct * tty, if (!tty || !info->xmit_buf) return 0; - save_flags(flags); + local_save_flags(flags); while (1) { - cli(); + local_irq_disable(); c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, SERIAL_XMIT_SIZE - info->xmit_head)); + local_irq_restore(flags); + if (c <= 0) break; memcpy(info->xmit_buf + info->xmit_head, buf, c); + + local_irq_disable(); info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1); info->xmit_cnt += c; - restore_flags(flags); + local_irq_restore(flags); buf += c; count -= c; total += c; @@ -787,7 +771,7 @@ static int rs_write(struct tty_struct * tty, if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) { /* Enable transmitter */ - cli(); + local_irq_disable(); #ifndef USE_INTS while(info->xmit_cnt) { #endif @@ -807,9 +791,9 @@ static int rs_write(struct tty_struct * tty, #ifndef USE_INTS } #endif - restore_flags(flags); + local_irq_restore(flags); } - restore_flags(flags); + return total; } @@ -838,12 +822,13 @@ static int rs_chars_in_buffer(struct tty_struct *tty) static void rs_flush_buffer(struct tty_struct *tty) { struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; + unsigned long flags; if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) return; - cli(); + local_irq_save(flags); info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - sti(); + local_irq_restore(flags); tty_wakeup(tty); } @@ -973,14 +958,15 @@ static int get_lsr_info(struct m68k_serial * info, unsigned int *value) m68328_uart *uart = &uart_addr[info->line]; #endif unsigned char status; + unsigned long flags; - cli(); + local_irq_save(flags); #ifdef CONFIG_SERIAL_68328_RTS_CTS status = (uart->utx.w & UTX_CTS_STAT) ? 1 : 0; #else status = 0; #endif - sti(); + local_irq_restore(flags); put_user(status,value); return 0; } @@ -994,14 +980,13 @@ static void send_break(struct m68k_serial * info, unsigned int duration) unsigned long flags; if (!info->port) return; - save_flags(flags); - cli(); + local_irq_save(flags); #ifdef USE_INTS uart->utx.w |= UTX_SEND_BREAK; msleep_interruptible(duration); uart->utx.w &= ~UTX_SEND_BREAK; #endif - restore_flags(flags); + local_irq_restore(flags); } static int rs_ioctl(struct tty_struct *tty, struct file * file, @@ -1060,7 +1045,7 @@ static int rs_ioctl(struct tty_struct *tty, struct file * file, (struct serial_struct *) arg); case TIOCSERGETLSR: /* Get line status register */ if (access_ok(VERIFY_WRITE, (void *) arg, - sizeof(unsigned int)); + sizeof(unsigned int))) return get_lsr_info(info, (unsigned int *) arg); return -EFAULT; case TIOCSERGSTRUCT: @@ -1113,10 +1098,10 @@ static void rs_close(struct tty_struct *tty, struct file * filp) if (!info || serial_paranoia_check(info, tty->name, "rs_close")) return; - save_flags(flags); cli(); + local_irq_save(flags); if (tty_hung_up_p(filp)) { - restore_flags(flags); + local_irq_restore(flags); return; } @@ -1138,7 +1123,7 @@ static void rs_close(struct tty_struct *tty, struct file * filp) info->count = 0; } if (info->count) { - restore_flags(flags); + local_irq_restore(flags); return; } info->flags |= S_CLOSING; @@ -1186,7 +1171,7 @@ static void rs_close(struct tty_struct *tty, struct file * filp) } info->flags &= ~(S_NORMAL_ACTIVE|S_CLOSING); wake_up_interruptible(&info->close_wait); - restore_flags(flags); + local_irq_restore(flags); } /* @@ -1262,9 +1247,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, info->count--; info->blocked_open++; while (1) { - cli(); + local_irq_disable(); m68k_rtsdtr(info, 1); - sti(); + local_irq_enable(); current->state = TASK_INTERRUPTIBLE; if (tty_hung_up_p(filp) || !(info->flags & S_INITIALIZED)) { @@ -1444,7 +1429,7 @@ rs68328_init(void) return -ENOMEM; } - save_flags(flags); cli(); + local_irq_save(flags); for(i=0;i<NR_PORTS;i++) { @@ -1489,7 +1474,7 @@ rs68328_init(void) serial_pm[i]->data = info; #endif } - restore_flags(flags); + local_irq_restore(flags); return 0; } diff --git a/drivers/serial/68328serial.h b/drivers/serial/68328serial.h index 978f8a609f3d..58aa2154655b 100644 --- a/drivers/serial/68328serial.h +++ b/drivers/serial/68328serial.h @@ -11,7 +11,6 @@ #ifndef _MC683XX_SERIAL_H #define _MC683XX_SERIAL_H -#include <linux/config.h> struct serial_struct { int type; diff --git a/drivers/serial/68360serial.c b/drivers/serial/68360serial.c index 9843ae3d420e..e80e70e9b126 100644 --- a/drivers/serial/68360serial.c +++ b/drivers/serial/68360serial.c @@ -20,7 +20,6 @@ * int rs_360_init(void); */ -#include <linux/config.h> #include <linux/module.h> #include <linux/errno.h> #include <linux/signal.h> diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index bbf78aaf9e01..0995430e4cf1 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -19,7 +19,6 @@ * mapbase is the physical address of the IO port. * membase is an 'ioremapped' cookie. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -49,7 +48,7 @@ /* * Configuration: - * share_irqs - whether we pass SA_SHIRQ to request_irq(). This option + * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option * is unsafe when used on edge-triggered interrupts. */ static unsigned int share_irqs = SERIAL8250_SHARE_IRQS; @@ -1401,7 +1400,7 @@ static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up) static int serial_link_irq_chain(struct uart_8250_port *up) { struct irq_info *i = irq_lists + up->port.irq; - int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0; + int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; spin_lock_irq(&i->lock); @@ -2354,7 +2353,6 @@ int __init serial8250_start_console(struct uart_port *port, char *options) static struct uart_driver serial8250_reg = { .owner = THIS_MODULE, .driver_name = "serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = 64, diff --git a/drivers/serial/8250.h b/drivers/serial/8250.h index 490606b87095..91bd28f2bb47 100644 --- a/drivers/serial/8250.h +++ b/drivers/serial/8250.h @@ -15,7 +15,6 @@ * $Id: 8250.h,v 1.8 2002/07/21 21:32:30 rmk Exp $ */ -#include <linux/config.h> #include <linux/serial_8250.h> struct old_serial_port { diff --git a/drivers/serial/8250_mca.c b/drivers/serial/8250_mca.c index ac205256d5f3..d10be944ad44 100644 --- a/drivers/serial/8250_mca.c +++ b/drivers/serial/8250_mca.c @@ -8,7 +8,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -#include <linux/config.h> #include <linux/module.h> #include <linux/init.h> #include <linux/mca.h> diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c index 950560ff9b46..a1d322f8a16c 100644 --- a/drivers/serial/8250_pci.c +++ b/drivers/serial/8250_pci.c @@ -594,8 +594,8 @@ pci_default_setup(struct serial_private *priv, struct pciserial_board *board, else offset += idx * board->uart_offset; - maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) / - (8 << board->reg_shift); + maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >> + (board->reg_shift + 3); if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr) return 1; diff --git a/drivers/serial/8250_pnp.c b/drivers/serial/8250_pnp.c index b79ed0665d51..632f62d6ec7e 100644 --- a/drivers/serial/8250_pnp.c +++ b/drivers/serial/8250_pnp.c @@ -323,8 +323,10 @@ static const struct pnp_device_id pnp_dev_table[] = { { "USR9180", 0 }, /* U.S. Robotics 56K Voice INT PnP*/ { "USR9190", 0 }, - /* HP Compaq Tablet PC tc1100 Wacom tablet */ + /* Wacom tablets */ + { "WACF004", 0 }, { "WACF005", 0 }, + { "WACF006", 0 }, /* Rockwell's (PORALiNK) 33600 INT PNP */ { "WCI0003", 0 }, /* Unkown PnP modems */ @@ -429,6 +431,8 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) #endif port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; + if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE) + port.flags |= UPF_SHARE_IRQ; port.uartclk = 1843200; port.dev = &dev->dev; diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 5fff79e7127f..5b48ac22c9c5 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -300,21 +300,22 @@ config SERIAL_AMBA_PL011_CONSOLE kernel at boot time.) config SERIAL_AT91 - bool "AT91RM9200 serial port support" - depends on ARM && ARCH_AT91RM9200 + bool "AT91RM9200 / AT91SAM9261 serial port support" + depends on ARM && (ARCH_AT91RM9200 || ARCH_AT91SAM9261) select SERIAL_CORE help - This enables the driver for the on-chip UARTs of the AT91RM9200 - processor. + This enables the driver for the on-chip UARTs of the Atmel + AT91RM9200 and AT91SAM926 processor. config SERIAL_AT91_CONSOLE - bool "Support for console on AT91RM9200 serial port" + bool "Support for console on AT91RM9200 / AT91SAM9261 serial port" depends on SERIAL_AT91=y select SERIAL_CORE_CONSOLE help - Say Y here if you wish to use a UART on the AT91RM9200 as the system - console (the system console is the device which receives all kernel - messages and warnings and which allows logins in single user mode). + Say Y here if you wish to use a UART on the Atmel AT91RM9200 or + AT91SAM9261 as the system console (the system console is the device + which receives all kernel messages and warnings and which allows + logins in single user mode). config SERIAL_AT91_TTYAT bool "Install as device ttyAT0-4 instead of ttyS0-4" @@ -353,21 +354,24 @@ config SERIAL_CLPS711X_CONSOLE kernel at boot time.) config SERIAL_S3C2410 - tristate "Samsung S3C2410 Serial port support" + tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support" depends on ARM && ARCH_S3C2410 select SERIAL_CORE help - Support for the on-chip UARTs on the Samsung S3C2410X CPU, + Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, providing /dev/ttySAC0, 1 and 2 (note, some machines may not provide all of these ports, depending on how the serial port pins are configured. + Currently this driver supports the UARTS on the S3C2410, S3C2440, + S3C2442, S3C2412 and S3C2413 CPUs. + config SERIAL_S3C2410_CONSOLE bool "Support for console on S3C2410 serial port" depends on SERIAL_S3C2410=y select SERIAL_CORE_CONSOLE help - Allow selection of the S3C2410 on-board serial ports for use as + Allow selection of the S3C24XX on-board serial ports for use as an virtual console. Even if you say Y here, the currently visible virtual console diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c index e920d196d0b1..7311d8487c96 100644 --- a/drivers/serial/amba-pl010.c +++ b/drivers/serial/amba-pl010.c @@ -31,7 +31,6 @@ * required, these have to be supplied via some other means (eg, GPIO) * and hooked into this driver. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_AMBA_PL010_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/serial/amba-pl011.c b/drivers/serial/amba-pl011.c index 3d966cfc9a38..a8d7124e84a1 100644 --- a/drivers/serial/amba-pl011.c +++ b/drivers/serial/amba-pl011.c @@ -31,7 +31,6 @@ * required, these have to be supplied via some other means (eg, GPIO) * and hooked into this driver. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/serial/at91_serial.c b/drivers/serial/at91_serial.c index 6547fe0cef96..a7d664383dae 100644 --- a/drivers/serial/at91_serial.c +++ b/drivers/serial/at91_serial.c @@ -2,7 +2,6 @@ * linux/drivers/char/at91_serial.c * * Driver for Atmel AT91RM9200 Serial ports - * * Copyright (C) 2003 Rick Bronson * * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. @@ -23,24 +22,25 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> #include <linux/slab.h> #include <linux/init.h> #include <linux/serial.h> +#include <linux/clk.h> #include <linux/console.h> #include <linux/sysrq.h> #include <linux/tty_flip.h> +#include <linux/platform_device.h> #include <asm/io.h> #include <asm/arch/at91rm9200_usart.h> -#include <asm/mach/serial_at91rm9200.h> +#include <asm/arch/at91rm9200_pdc.h> +#include <asm/mach/serial_at91.h> #include <asm/arch/board.h> -#include <asm/arch/pio.h> - +#include <asm/arch/system.h> #if defined(CONFIG_SERIAL_AT91_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -67,7 +67,6 @@ #endif -#define AT91_VA_BASE_DBGU ((unsigned long) AT91_VA_BASE_SYS + AT91_DBGU) #define AT91_ISR_PASS_LIMIT 256 #define UART_PUT_CR(port,v) writel(v, (port)->membase + AT91_US_CR) @@ -87,16 +86,33 @@ /* PDC registers */ #define UART_PUT_PTCR(port,v) writel(v, (port)->membase + AT91_PDC_PTCR) +#define UART_GET_PTSR(port) readl((port)->membase + AT91_PDC_PTSR) + #define UART_PUT_RPR(port,v) writel(v, (port)->membase + AT91_PDC_RPR) +#define UART_GET_RPR(port) readl((port)->membase + AT91_PDC_RPR) #define UART_PUT_RCR(port,v) writel(v, (port)->membase + AT91_PDC_RCR) -#define UART_GET_RCR(port) readl((port)->membase + AT91_PDC_RCR) #define UART_PUT_RNPR(port,v) writel(v, (port)->membase + AT91_PDC_RNPR) #define UART_PUT_RNCR(port,v) writel(v, (port)->membase + AT91_PDC_RNCR) +#define UART_PUT_TPR(port,v) writel(v, (port)->membase + AT91_PDC_TPR) +#define UART_PUT_TCR(port,v) writel(v, (port)->membase + AT91_PDC_TCR) +//#define UART_PUT_TNPR(port,v) writel(v, (port)->membase + AT91_PDC_TNPR) +//#define UART_PUT_TNCR(port,v) writel(v, (port)->membase + AT91_PDC_TNCR) static int (*at91_open)(struct uart_port *); static void (*at91_close)(struct uart_port *); +/* + * We wrap our port structure around the generic uart_port. + */ +struct at91_uart_port { + struct uart_port uart; /* uart */ + struct clk *clk; /* uart clock */ + unsigned short suspended; /* is port suspended? */ +}; + +static struct at91_uart_port at91_ports[AT91_NR_UART]; + #ifdef SUPPORT_SYSRQ static struct console at91_console; #endif @@ -115,16 +131,19 @@ static u_int at91_tx_empty(struct uart_port *port) static void at91_set_mctrl(struct uart_port *port, u_int mctrl) { unsigned int control = 0; + unsigned int mode; - /* - * Errata #39: RTS0 is not internally connected to PA21. We need to drive - * the pin manually. - */ - if (port->mapbase == AT91_VA_BASE_US0) { - if (mctrl & TIOCM_RTS) - at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0); - else - at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0); + if (arch_identify() == ARCH_ID_AT91RM9200) { + /* + * AT91RM9200 Errata #39: RTS0 is not internally connected to PA21. + * We need to drive the pin manually. + */ + if (port->mapbase == AT91_BASE_US0) { + if (mctrl & TIOCM_RTS) + at91_sys_write(AT91_PIOA + PIO_CODR, AT91_PA21_RTS0); + else + at91_sys_write(AT91_PIOA + PIO_SODR, AT91_PA21_RTS0); + } } if (mctrl & TIOCM_RTS) @@ -137,7 +156,15 @@ static void at91_set_mctrl(struct uart_port *port, u_int mctrl) else control |= AT91_US_DTRDIS; - UART_PUT_CR(port,control); + UART_PUT_CR(port, control); + + /* Local loopback mode? */ + mode = UART_GET_MR(port) & ~AT91_US_CHMODE; + if (mctrl & TIOCM_LOOP) + mode |= AT91_US_CHMODE_LOC_LOOP; + else + mode |= AT91_US_CHMODE_NORMAL; + UART_PUT_MR(port, mode); } /* @@ -169,8 +196,9 @@ static u_int at91_get_mctrl(struct uart_port *port) */ static void at91_stop_tx(struct uart_port *port) { + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + UART_PUT_IDR(port, AT91_US_TXRDY); - port->read_status_mask &= ~AT91_US_TXRDY; } /* @@ -178,7 +206,8 @@ static void at91_stop_tx(struct uart_port *port) */ static void at91_start_tx(struct uart_port *port) { - port->read_status_mask |= AT91_US_TXRDY; + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + UART_PUT_IER(port, AT91_US_TXRDY); } @@ -187,6 +216,8 @@ static void at91_start_tx(struct uart_port *port) */ static void at91_stop_rx(struct uart_port *port) { + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + UART_PUT_IDR(port, AT91_US_RXRDY); } @@ -195,7 +226,6 @@ static void at91_stop_rx(struct uart_port *port) */ static void at91_enable_ms(struct uart_port *port) { - port->read_status_mask |= (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC); UART_PUT_IER(port, AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC); } @@ -218,8 +248,8 @@ static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs) struct tty_struct *tty = port->info->tty; unsigned int status, ch, flg; - status = UART_GET_CSR(port) & port->read_status_mask; - while (status & (AT91_US_RXRDY)) { + status = UART_GET_CSR(port); + while (status & AT91_US_RXRDY) { ch = UART_GET_CHAR(port); port->icount.rx++; @@ -230,40 +260,38 @@ static void at91_rx_chars(struct uart_port *port, struct pt_regs *regs) * note that the error handling code is * out of the main execution path */ - if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE))) { + if (unlikely(status & (AT91_US_PARE | AT91_US_FRAME | AT91_US_OVRE | AT91_US_RXBRK))) { UART_PUT_CR(port, AT91_US_RSTSTA); /* clear error */ - if (status & (AT91_US_PARE)) + if (status & AT91_US_RXBRK) { + status &= ~(AT91_US_PARE | AT91_US_FRAME); /* ignore side-effect */ + port->icount.brk++; + if (uart_handle_break(port)) + goto ignore_char; + } + if (status & AT91_US_PARE) port->icount.parity++; - if (status & (AT91_US_FRAME)) + if (status & AT91_US_FRAME) port->icount.frame++; - if (status & (AT91_US_OVRE)) + if (status & AT91_US_OVRE) port->icount.overrun++; - if (status & AT91_US_PARE) + status &= port->read_status_mask; + + if (status & AT91_US_RXBRK) + flg = TTY_BREAK; + else if (status & AT91_US_PARE) flg = TTY_PARITY; else if (status & AT91_US_FRAME) flg = TTY_FRAME; - if (status & AT91_US_OVRE) { - /* - * overrun does *not* affect the character - * we read from the FIFO - */ - tty_insert_flip_char(tty, ch, flg); - ch = 0; - flg = TTY_OVERRUN; - } -#ifdef SUPPORT_SYSRQ - port->sysrq = 0; -#endif } if (uart_handle_sysrq_char(port, ch, regs)) goto ignore_char; - tty_insert_flip_char(tty, ch, flg); + uart_insert_char(port, status, AT91_US_OVRE, ch, flg); ignore_char: - status = UART_GET_CSR(port) & port->read_status_mask; + status = UART_GET_CSR(port); } tty_flip_buffer_push(tty); @@ -308,40 +336,35 @@ static void at91_tx_chars(struct uart_port *port) static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs) { struct uart_port *port = dev_id; + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; unsigned int status, pending, pass_counter = 0; status = UART_GET_CSR(port); - pending = status & port->read_status_mask; - if (pending) { - do { - if (pending & AT91_US_RXRDY) - at91_rx_chars(port, regs); - - /* Clear the relevent break bits */ - if (pending & AT91_US_RXBRK) { - UART_PUT_CR(port, AT91_US_RSTSTA); - port->icount.brk++; - uart_handle_break(port); - } + pending = status & UART_GET_IMR(port); + while (pending) { + /* Interrupt receive */ + if (pending & AT91_US_RXRDY) + at91_rx_chars(port, regs); + + // TODO: All reads to CSR will clear these interrupts! + if (pending & AT91_US_RIIC) port->icount.rng++; + if (pending & AT91_US_DSRIC) port->icount.dsr++; + if (pending & AT91_US_DCDIC) + uart_handle_dcd_change(port, !(status & AT91_US_DCD)); + if (pending & AT91_US_CTSIC) + uart_handle_cts_change(port, !(status & AT91_US_CTS)); + if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC)) + wake_up_interruptible(&port->info->delta_msr_wait); + + /* Interrupt transmit */ + if (pending & AT91_US_TXRDY) + at91_tx_chars(port); + + if (pass_counter++ > AT91_ISR_PASS_LIMIT) + break; - // TODO: All reads to CSR will clear these interrupts! - if (pending & AT91_US_RIIC) port->icount.rng++; - if (pending & AT91_US_DSRIC) port->icount.dsr++; - if (pending & AT91_US_DCDIC) - uart_handle_dcd_change(port, !(status & AT91_US_DCD)); - if (pending & AT91_US_CTSIC) - uart_handle_cts_change(port, !(status & AT91_US_CTS)); - if (pending & (AT91_US_RIIC | AT91_US_DSRIC | AT91_US_DCDIC | AT91_US_CTSIC)) - wake_up_interruptible(&port->info->delta_msr_wait); - - if (pending & AT91_US_TXRDY) - at91_tx_chars(port); - if (pass_counter++ > AT91_ISR_PASS_LIMIT) - break; - - status = UART_GET_CSR(port); - pending = status & port->read_status_mask; - } while (pending); + status = UART_GET_CSR(port); + pending = status & UART_GET_IMR(port); } return IRQ_HANDLED; } @@ -351,6 +374,7 @@ static irqreturn_t at91_interrupt(int irq, void *dev_id, struct pt_regs *regs) */ static int at91_startup(struct uart_port *port) { + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; int retval; /* @@ -363,7 +387,7 @@ static int at91_startup(struct uart_port *port) /* * Allocate the IRQ */ - retval = request_irq(port->irq, at91_interrupt, SA_SHIRQ, "at91_serial", port); + retval = request_irq(port->irq, at91_interrupt, IRQF_SHARED, "at91_serial", port); if (retval) { printk("at91_serial: at91_startup - Can't get irq\n"); return retval; @@ -381,14 +405,14 @@ static int at91_startup(struct uart_port *port) } } - port->read_status_mask = AT91_US_RXRDY | AT91_US_TXRDY | AT91_US_OVRE - | AT91_US_FRAME | AT91_US_PARE | AT91_US_RXBRK; /* * Finally, enable the serial port */ UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); /* enable xmit & rcvr */ - UART_PUT_IER(port, AT91_US_RXRDY); /* do receive only */ + + UART_PUT_IER(port, AT91_US_RXRDY); /* enable receive only */ + return 0; } @@ -397,6 +421,8 @@ static int at91_startup(struct uart_port *port) */ static void at91_shutdown(struct uart_port *port) { + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + /* * Disable all interrupts, port and break condition. */ @@ -421,21 +447,22 @@ static void at91_shutdown(struct uart_port *port) */ static void at91_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) { + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + switch (state) { case 0: /* * Enable the peripheral clock for this serial port. * This is called on uart_open() or a resume event. */ - at91_sys_write(AT91_PMC_PCER, 1 << port->irq); + clk_enable(at91_port->clk); break; case 3: /* * Disable the peripheral clock for this serial port. * This is called on uart_close() or a suspend event. */ - if (port->irq != AT91_ID_SYS) /* is this a shared clock? */ - at91_sys_write(AT91_PMC_PCDR, 1 << port->irq); + clk_disable(at91_port->clk); break; default: printk(KERN_ERR "at91_serial: unknown pm %d\n", state); @@ -494,9 +521,9 @@ static void at91_set_termios(struct uart_port *port, struct termios * termios, s spin_lock_irqsave(&port->lock, flags); - port->read_status_mask |= AT91_US_OVRE; + port->read_status_mask = AT91_US_OVRE; if (termios->c_iflag & INPCK) - port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE; + port->read_status_mask |= (AT91_US_FRAME | AT91_US_PARE); if (termios->c_iflag & (BRKINT | PARMRK)) port->read_status_mask |= AT91_US_RXBRK; @@ -552,7 +579,7 @@ static void at91_set_termios(struct uart_port *port, struct termios * termios, s */ static const char *at91_type(struct uart_port *port) { - return (port->type == PORT_AT91RM9200) ? "AT91_SERIAL" : NULL; + return (port->type == PORT_AT91) ? "AT91_SERIAL" : NULL; } /* @@ -560,8 +587,15 @@ static const char *at91_type(struct uart_port *port) */ static void at91_release_port(struct uart_port *port) { - release_mem_region(port->mapbase, - (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K); + struct platform_device *pdev = to_platform_device(port->dev); + int size = pdev->resource[0].end - pdev->resource[0].start + 1; + + release_mem_region(port->mapbase, size); + + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } } /* @@ -569,10 +603,21 @@ static void at91_release_port(struct uart_port *port) */ static int at91_request_port(struct uart_port *port) { - return request_mem_region(port->mapbase, - (port->mapbase == AT91_VA_BASE_DBGU) ? 512 : SZ_16K, - "at91_serial") != NULL ? 0 : -EBUSY; + struct platform_device *pdev = to_platform_device(port->dev); + int size = pdev->resource[0].end - pdev->resource[0].start + 1; + + if (!request_mem_region(port->mapbase, size, "at91_serial")) + return -EBUSY; + + if (port->flags & UPF_IOREMAP) { + port->membase = ioremap(port->mapbase, size); + if (port->membase == NULL) { + release_mem_region(port->mapbase, size); + return -ENOMEM; + } + } + return 0; } /* @@ -581,7 +626,7 @@ static int at91_request_port(struct uart_port *port) static void at91_config_port(struct uart_port *port, int flags) { if (flags & UART_CONFIG_TYPE) { - port->type = PORT_AT91RM9200; + port->type = PORT_AT91; at91_request_port(port); } } @@ -592,7 +637,7 @@ static void at91_config_port(struct uart_port *port, int flags) static int at91_verify_port(struct uart_port *port, struct serial_struct *ser) { int ret = 0; - if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91RM9200) + if (ser->type != PORT_UNKNOWN && ser->type != PORT_AT91) ret = -EINVAL; if (port->irq != ser->irq) ret = -EINVAL; @@ -624,33 +669,47 @@ static struct uart_ops at91_pops = { .type = at91_type, .release_port = at91_release_port, .request_port = at91_request_port, - .config_port = at91_config_port, - .verify_port = at91_verify_port, + .config_port = at91_config_port, + .verify_port = at91_verify_port, .pm = at91_serial_pm, }; -static struct uart_port at91_ports[AT91_NR_UART]; - -void __init at91_init_ports(void) +/* + * Configure the port from the platform device resource info. + */ +static void __devinit at91_init_port(struct at91_uart_port *at91_port, struct platform_device *pdev) { - static int first = 1; - int i; - - if (!first) - return; - first = 0; + struct uart_port *port = &at91_port->uart; + struct at91_uart_data *data = pdev->dev.platform_data; + + port->iotype = UPIO_MEM; + port->flags = UPF_BOOT_AUTOCONF; + port->ops = &at91_pops; + port->fifosize = 1; + port->line = pdev->id; + port->dev = &pdev->dev; + + port->mapbase = pdev->resource[0].start; + port->irq = pdev->resource[1].start; + + if (port->mapbase == AT91_VA_BASE_SYS + AT91_DBGU) /* Part of system perpherals - already mapped */ + port->membase = (void __iomem *) port->mapbase; + else { + port->flags |= UPF_IOREMAP; + port->membase = NULL; + } - for (i = 0; i < AT91_NR_UART; i++) { - at91_ports[i].iotype = UPIO_MEM; - at91_ports[i].flags = UPF_BOOT_AUTOCONF; - at91_ports[i].uartclk = at91_master_clock; - at91_ports[i].ops = &at91_pops; - at91_ports[i].fifosize = 1; - at91_ports[i].line = i; - } + if (!at91_port->clk) { /* for console, the clock could already be configured */ + at91_port->clk = clk_get(&pdev->dev, "usart"); + clk_enable(at91_port->clk); + port->uartclk = clk_get_rate(at91_port->clk); + } } -void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns) +/* + * Register board-specific modem-control line handlers. + */ +void __init at91_register_uart_fns(struct at91_port_fns *fns) { if (fns->enable_ms) at91_pops.enable_ms = fns->enable_ms; @@ -664,51 +723,6 @@ void __init at91_register_uart_fns(struct at91rm9200_port_fns *fns) at91_pops.set_wake = fns->set_wake; } -/* - * Setup ports. - */ -void __init at91_register_uart(int idx, int port) -{ - if ((idx < 0) || (idx >= AT91_NR_UART)) { - printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx); - return; - } - - switch (port) { - case 0: - at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US0; - at91_ports[idx].mapbase = AT91_VA_BASE_US0; - at91_ports[idx].irq = AT91_ID_US0; - AT91_CfgPIO_USART0(); - break; - case 1: - at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US1; - at91_ports[idx].mapbase = AT91_VA_BASE_US1; - at91_ports[idx].irq = AT91_ID_US1; - AT91_CfgPIO_USART1(); - break; - case 2: - at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US2; - at91_ports[idx].mapbase = AT91_VA_BASE_US2; - at91_ports[idx].irq = AT91_ID_US2; - AT91_CfgPIO_USART2(); - break; - case 3: - at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_US3; - at91_ports[idx].mapbase = AT91_VA_BASE_US3; - at91_ports[idx].irq = AT91_ID_US3; - AT91_CfgPIO_USART3(); - break; - case 4: - at91_ports[idx].membase = (void __iomem *) AT91_VA_BASE_DBGU; - at91_ports[idx].mapbase = AT91_VA_BASE_DBGU; - at91_ports[idx].irq = AT91_ID_SYS; - AT91_CfgPIO_DBGU(); - break; - default: - printk(KERN_ERR "%s : bad port number %d\n", __FUNCTION__, port); - } -} #ifdef CONFIG_SERIAL_AT91_CONSOLE static void at91_console_putchar(struct uart_port *port, int ch) @@ -723,7 +737,7 @@ static void at91_console_putchar(struct uart_port *port, int ch) */ static void at91_console_write(struct console *co, const char *s, u_int count) { - struct uart_port *port = at91_ports + co->index; + struct uart_port *port = &at91_ports[co->index].uart; unsigned int status, imr; /* @@ -778,23 +792,15 @@ static void __init at91_console_get_options(struct uart_port *port, int *baud, i static int __init at91_console_setup(struct console *co, char *options) { - struct uart_port *port; + struct uart_port *port = &at91_ports[co->index].uart; int baud = 115200; int bits = 8; int parity = 'n'; int flow = 'n'; - /* - * Check whether an invalid uart number has been specified, and - * if so, search for the first available port that does have - * console support. - */ - port = uart_get_console(at91_ports, AT91_NR_UART, co); + if (port->membase == 0) /* Port not initialized yet - delay setup */ + return -ENODEV; - /* - * Enable the serial console, in-case bootloader did not do it. - */ - at91_sys_write(AT91_PMC_PCER, 1 << port->irq); /* enable clock */ UART_PUT_IDR(port, -1); /* disable interrupts */ UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX); UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN); @@ -821,58 +827,147 @@ static struct console at91_console = { #define AT91_CONSOLE_DEVICE &at91_console -static int __init at91_console_init(void) +/* + * Early console initialization (before VM subsystem initialized). + */ +static int __init at91_console_init(void) { - at91_init_ports(); + if (at91_default_console_device) { + add_preferred_console(AT91_DEVICENAME, at91_default_console_device->id, NULL); + at91_init_port(&(at91_ports[at91_default_console_device->id]), at91_default_console_device); + register_console(&at91_console); + } - at91_console.index = at91_console_port; - register_console(&at91_console); return 0; } console_initcall(at91_console_init); +/* + * Late console initialization. + */ +static int __init at91_late_console_init(void) +{ + if (at91_default_console_device && !(at91_console.flags & CON_ENABLED)) + register_console(&at91_console); + + return 0; +} +core_initcall(at91_late_console_init); + #else #define AT91_CONSOLE_DEVICE NULL #endif static struct uart_driver at91_uart = { .owner = THIS_MODULE, - .driver_name = AT91_DEVICENAME, + .driver_name = "at91_serial", .dev_name = AT91_DEVICENAME, - .devfs_name = AT91_DEVICENAME, .major = SERIAL_AT91_MAJOR, .minor = MINOR_START, .nr = AT91_NR_UART, .cons = AT91_CONSOLE_DEVICE, }; -static int __init at91_serial_init(void) +#ifdef CONFIG_PM +static int at91_serial_suspend(struct platform_device *pdev, pm_message_t state) { - int ret, i; + struct uart_port *port = platform_get_drvdata(pdev); + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + + if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock()) + enable_irq_wake(port->irq); + else { + disable_irq_wake(port->irq); + uart_suspend_port(&at91_uart, port); + at91_port->suspended = 1; + } - at91_init_ports(); + return 0; +} - ret = uart_register_driver(&at91_uart); - if (ret) - return ret; +static int at91_serial_resume(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; - for (i = 0; i < AT91_NR_UART; i++) { - if (at91_serial_map[i] >= 0) - uart_add_one_port(&at91_uart, &at91_ports[i]); + if (at91_port->suspended) { + uart_resume_port(&at91_uart, port); + at91_port->suspended = 0; } return 0; } +#else +#define at91_serial_suspend NULL +#define at91_serial_resume NULL +#endif -static void __exit at91_serial_exit(void) +static int __devinit at91_serial_probe(struct platform_device *pdev) { - int i; + struct at91_uart_port *port; + int ret; - for (i = 0; i < AT91_NR_UART; i++) { - if (at91_serial_map[i] >= 0) - uart_remove_one_port(&at91_uart, &at91_ports[i]); - } + port = &at91_ports[pdev->id]; + at91_init_port(port, pdev); + ret = uart_add_one_port(&at91_uart, &port->uart); + if (!ret) { + device_init_wakeup(&pdev->dev, 1); + platform_set_drvdata(pdev, port); + } + + return ret; +} + +static int __devexit at91_serial_remove(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct at91_uart_port *at91_port = (struct at91_uart_port *) port; + int ret = 0; + + clk_disable(at91_port->clk); + clk_put(at91_port->clk); + + device_init_wakeup(&pdev->dev, 0); + platform_set_drvdata(pdev, NULL); + + if (port) { + ret = uart_remove_one_port(&at91_uart, port); + kfree(port); + } + + return ret; +} + +static struct platform_driver at91_serial_driver = { + .probe = at91_serial_probe, + .remove = __devexit_p(at91_serial_remove), + .suspend = at91_serial_suspend, + .resume = at91_serial_resume, + .driver = { + .name = "at91_usart", + .owner = THIS_MODULE, + }, +}; + +static int __init at91_serial_init(void) +{ + int ret; + + ret = uart_register_driver(&at91_uart); + if (ret) + return ret; + + ret = platform_driver_register(&at91_serial_driver); + if (ret) + uart_unregister_driver(&at91_uart); + + return ret; +} + +static void __exit at91_serial_exit(void) +{ + platform_driver_unregister(&at91_serial_driver); uart_unregister_driver(&at91_uart); } diff --git a/drivers/serial/clps711x.c b/drivers/serial/clps711x.c index 2691112c84ad..f27d852ce50d 100644 --- a/drivers/serial/clps711x.c +++ b/drivers/serial/clps711x.c @@ -25,7 +25,6 @@ * $Id: clps711x.c,v 1.42 2002/07/28 10:03:28 rmk Exp $ * */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_CLPS711X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index 5cba59ad7dc5..90ff96e3339b 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -31,7 +31,6 @@ * */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c index 17406a05ce1f..95afc37297a8 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c @@ -27,7 +27,6 @@ * */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index cdba128250a9..ef3bb476c432 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -27,7 +27,6 @@ * */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c index 89700141f87e..cabd048c8636 100644 --- a/drivers/serial/crisv10.c +++ b/drivers/serial/crisv10.c @@ -415,7 +415,7 @@ * Fixed DEF_TX value that caused the serial transmitter pin (txd) to go to 0 when * closing the last filehandle, NASTY!. * Added break generation, not tested though! - * Use SA_SHIRQ when request_irq() for ser2 and ser3 (shared with) par0 and par1. + * Use IRQF_SHARED when request_irq() for ser2 and ser3 (shared with) par0 and par1. * You can't use them at the same time (yet..), but you can hopefully switch * between ser2/par0, ser3/par1 with the same kernel config. * Replaced some magic constants with defines @@ -425,7 +425,6 @@ static char *serial_version = "$Revision: 1.25 $"; -#include <linux/config.h> #include <linux/types.h> #include <linux/errno.h> #include <linux/signal.h> @@ -2573,12 +2572,6 @@ static void flush_to_flip_buffer(struct e100_serial *info) DFLIP( if (1) { - - if (test_bit(TTY_DONT_FLIP, &tty->flags)) { - DEBUG_LOG(info->line, "*** TTY_DONT_FLIP set flip.count %i ***\n", tty->flip.count); - DEBUG_LOG(info->line, "*** recv_cnt %i\n", info->recv_cnt); - } else { - } DEBUG_LOG(info->line, "*** rxtot %i\n", info->icount.rx); DEBUG_LOG(info->line, "ldisc %lu\n", tty->ldisc.chars_in_buffer(tty)); DEBUG_LOG(info->line, "room %lu\n", tty->ldisc.receive_room(tty)); @@ -4884,7 +4877,7 @@ rs_init(void) driver->init_termios = tty_std_termios; driver->init_termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */ - driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS; + driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; driver->termios = serial_termios; driver->termios_locked = serial_termios_locked; @@ -4949,55 +4942,55 @@ rs_init(void) /* Not needed in simulator. May only complicate stuff. */ /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */ - if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial ", NULL)) + if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", NULL)) panic("irq8"); #ifdef CONFIG_ETRAX_SERIAL_PORT0 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT - if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 0 dma tr", NULL)) + if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 0 dma tr", NULL)) panic("irq22"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN - if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 0 dma rec", NULL)) + if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 0 dma rec", NULL)) panic("irq23"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT1 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT - if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 1 dma tr", NULL)) + if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 1 dma tr", NULL)) panic("irq24"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN - if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 1 dma rec", NULL)) + if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 1 dma rec", NULL)) panic("irq25"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT2 /* DMA Shared with par0 (and SCSI0 and ATA) */ #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT - if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma tr", NULL)) + if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma tr", NULL)) panic("irq18"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN - if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma rec", NULL)) + if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma rec", NULL)) panic("irq19"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT3 /* DMA Shared with par1 (and SCSI1 and Extern DMA 0) */ #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT - if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma tr", NULL)) + if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma tr", NULL)) panic("irq20"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN - if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma rec", NULL)) + if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma rec", NULL)) panic("irq21"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST - if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, SA_SHIRQ | SA_INTERRUPT, + if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, IRQF_SHARED | IRQF_DISABLED, "fast serial dma timeout", NULL)) { printk(KERN_CRIT "err: timer1 irq\n"); } diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h index 1800c0e7531a..f30b93d6ef79 100644 --- a/drivers/serial/crisv10.h +++ b/drivers/serial/crisv10.h @@ -7,7 +7,6 @@ #ifndef _ETRAX_SERIAL_H #define _ETRAX_SERIAL_H -#include <linux/config.h> #include <linux/circ_buf.h> #include <asm/termios.h> diff --git a/drivers/serial/dz.c b/drivers/serial/dz.c index bf71bad5c34f..d119c8296a78 100644 --- a/drivers/serial/dz.c +++ b/drivers/serial/dz.c @@ -26,7 +26,6 @@ #undef DEBUG_DZ -#include <linux/config.h> #include <linux/module.h> #include <linux/interrupt.h> #include <linux/init.h> @@ -768,11 +767,7 @@ void __init dz_serial_console_init(void) static struct uart_driver dz_reg = { .owner = THIS_MODULE, .driver_name = "serial", -#ifdef CONFIG_DEVFS - .dev_name = "tts/%d", -#else .dev_name = "ttyS%d", -#endif .major = TTY_MAJOR, .minor = 64, .nr = DZ_NB_PORT, @@ -802,7 +797,7 @@ int __init dz_init(void) restore_flags(flags); if (request_irq(dz_ports[0].port.irq, dz_interrupt, - SA_INTERRUPT, "DZ", &dz_ports[0])) + IRQF_DISABLED, "DZ", &dz_ports[0])) panic("Unable to register DZ interrupt"); ret = uart_register_driver(&dz_reg); diff --git a/drivers/serial/icom.c b/drivers/serial/icom.c index 144a7a352b28..a3c00a252149 100644 --- a/drivers/serial/icom.c +++ b/drivers/serial/icom.c @@ -24,7 +24,6 @@ */ #define SERIAL_DO_RESTART #include <linux/module.h> -#include <linux/config.h> #include <linux/kernel.h> #include <linux/errno.h> #include <linux/signal.h> @@ -1564,7 +1563,7 @@ static int __devinit icom_probe(struct pci_dev *dev, /* save off irq and request irq line */ if ( (retval = request_irq(dev->irq, icom_interrupt, - SA_INTERRUPT | SA_SHIRQ, ICOM_DRIVER_NAME, + IRQF_DISABLED | IRQF_SHARED, ICOM_DRIVER_NAME, (void *) icom_adapter))) { goto probe_exit2; } diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index d202eb4f3848..4a142d6b8f38 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -25,7 +25,6 @@ * [29-Mar-2005] Mike Lee * Added hardware handshake */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_IMX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -405,7 +404,7 @@ static int imx_startup(struct uart_port *port) if (retval) goto error_out2; retval = request_irq(sport->rtsirq, imx_rtsint, - SA_TRIGGER_FALLING | SA_TRIGGER_RISING, + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, DRIVER_NAME, sport); if (retval) goto error_out3; @@ -888,7 +887,6 @@ static struct uart_driver imx_reg = { .owner = THIS_MODULE, .driver_name = DRIVER_NAME, .dev_name = "ttySMX", - .devfs_name = "ttsmx/", .major = SERIAL_IMX_MAJOR, .minor = MINOR_START, .nr = ARRAY_SIZE(imx_ports), diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c index c620209d7b9a..576ca1eaa2b6 100644 --- a/drivers/serial/ioc4_serial.c +++ b/drivers/serial/ioc4_serial.c @@ -2646,7 +2646,10 @@ static int ioc4_serial_remove_one(struct ioc4_driver_data *idd) struct ioc4_port *port; struct ioc4_soft *soft; + /* If serial driver did not attach, don't try to detach */ control = idd->idd_serial_data; + if (!control) + return 0; for (port_num = 0; port_num < IOC4_NUM_SERIAL_PORTS; port_num++) { for (port_type = UART_PORT_MIN; @@ -2778,6 +2781,12 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd) DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __FUNCTION__, idd->idd_pdev, idd->idd_pci_id)); + /* PCI-RT does not bring out serial connections. + * Do not attach to this particular IOC4. + */ + if (idd->idd_variant == IOC4_VARIANT_PCI_RT) + return 0; + /* request serial registers */ tmp_addr1 = idd->idd_bar0 + IOC4_SERIAL_OFFSET; @@ -2846,7 +2855,7 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd) control->ic_soft = soft; /* Hook up interrupt handler */ - if (!request_irq(idd->idd_pdev->irq, ioc4_intr, SA_SHIRQ, + if (!request_irq(idd->idd_pdev->irq, ioc4_intr, IRQF_SHARED, "sgi-ioc4serial", soft)) { control->ic_irq = idd->idd_pdev->irq; } else { diff --git a/drivers/serial/ip22zilog.c b/drivers/serial/ip22zilog.c index 651772474ac1..342042889f6e 100644 --- a/drivers/serial/ip22zilog.c +++ b/drivers/serial/ip22zilog.c @@ -12,7 +12,6 @@ * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org) * Copyright (C) 2002 David S. Miller (davem@redhat.com) */ -#include <linux/config.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/sched.h> @@ -1085,7 +1084,6 @@ static struct console ip22zilog_console = { static struct uart_driver ip22zilog_reg = { .owner = THIS_MODULE, .driver_name = "serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = 64, diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c index b3e1f71be4da..244f63be3a03 100644 --- a/drivers/serial/jsm/jsm_driver.c +++ b/drivers/serial/jsm/jsm_driver.c @@ -121,7 +121,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent) } rc = request_irq(brd->irq, brd->bd_ops->intr, - SA_INTERRUPT|SA_SHIRQ, "JSM", brd); + IRQF_DISABLED|IRQF_SHARED, "JSM", brd); if (rc) { printk(KERN_WARNING "Failed to hook IRQ %d\n",brd->irq); goto out_iounmap; diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c index 7d823705193c..f8262e6ad8d3 100644 --- a/drivers/serial/jsm/jsm_tty.c +++ b/drivers/serial/jsm/jsm_tty.c @@ -589,13 +589,6 @@ void jsm_input(struct jsm_channel *ch) ld = tty_ldisc_ref(tp); /* - * If the DONT_FLIP flag is on, don't flush our buffer, and act - * like the ld doesn't have any space to put the data right now. - */ - if (test_bit(TTY_DONT_FLIP, &tp->flags)) - len = 0; - - /* * If we were unable to get a reference to the ld, * don't flush our buffer, and act like the ld doesn't * have any space to put the data right now. diff --git a/drivers/serial/m32r_sio.c b/drivers/serial/m32r_sio.c index 321a40f33b50..e7fe4bb46eca 100644 --- a/drivers/serial/m32r_sio.c +++ b/drivers/serial/m32r_sio.c @@ -25,7 +25,6 @@ * membase is an 'ioremapped' cookie. This is compatible with the old * serial.c driver, and is currently the preferred form. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_M32R_SIO_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -543,7 +542,7 @@ static void serial_do_unlink(struct irq_info *i, struct uart_sio_port *up) static int serial_link_irq_chain(struct uart_sio_port *up) { struct irq_info *i = irq_lists + up->port.irq; - int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0; + int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; spin_lock_irq(&i->lock); @@ -1131,7 +1130,6 @@ console_initcall(m32r_sio_console_init); static struct uart_driver m32r_sio_reg = { .owner = THIS_MODULE, .driver_name = "sio", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = 64, diff --git a/drivers/serial/m32r_sio.h b/drivers/serial/m32r_sio.h index 7c3ec24f7e50..849f1b2c2531 100644 --- a/drivers/serial/m32r_sio.h +++ b/drivers/serial/m32r_sio.h @@ -15,7 +15,6 @@ * (at your option) any later version. */ -#include <linux/config.h> struct m32r_sio_probe { struct module *owner; diff --git a/drivers/serial/m32r_sio_reg.h b/drivers/serial/m32r_sio_reg.h index 9c864529451b..4671473793e3 100644 --- a/drivers/serial/m32r_sio_reg.h +++ b/drivers/serial/m32r_sio_reg.h @@ -15,7 +15,6 @@ #ifndef _M32R_SIO_REG_H #define _M32R_SIO_REG_H -#include <linux/config.h> #ifdef CONFIG_SERIAL_M32R_PLDSIO diff --git a/drivers/serial/mcfserial.c b/drivers/serial/mcfserial.c index 8cbbb954df2c..832abd3c4706 100644 --- a/drivers/serial/mcfserial.c +++ b/drivers/serial/mcfserial.c @@ -60,11 +60,11 @@ struct timer_list mcfrs_timer_struct; #if defined(CONFIG_HW_FEITH) #define CONSOLE_BAUD_RATE 38400 #define DEFAULT_CBAUD B38400 -#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) +#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) || defined(CONFIG_M5329EVB) #define CONSOLE_BAUD_RATE 115200 #define DEFAULT_CBAUD B115200 #elif defined(CONFIG_ARNEWSH) || defined(CONFIG_FREESCALE) || \ - defined(CONFIG_senTec) || defined(CONFIG_SNEHA) + defined(CONFIG_senTec) || defined(CONFIG_SNEHA) || defined(CONFIG_AVNET) #define CONSOLE_BAUD_RATE 19200 #define DEFAULT_CBAUD B19200 #endif @@ -93,7 +93,7 @@ static struct tty_driver *mcfrs_serial_driver; #undef SERIAL_DEBUG_FLOW #if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \ - defined(CONFIG_M520x) + defined(CONFIG_M520x) || defined(CONFIG_M532x) #define IRQBASE (MCFINT_VECBASE+MCFINT_UART0) #else #define IRQBASE 73 @@ -1545,6 +1545,28 @@ static void mcfrs_irqinit(struct mcf_serial *info) *feci2c_par |= MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2 | MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2; } +#elif defined(CONFIG_M532x) + volatile unsigned char *uartp; + uartp = info->addr; + switch (info->line) { + case 0: + MCF_INTC0_ICR26 = 0x3; + MCF_INTC0_CIMR = 26; + /* GPIO initialization */ + MCF_GPIO_PAR_UART |= 0x000F; + break; + case 1: + MCF_INTC0_ICR27 = 0x3; + MCF_INTC0_CIMR = 27; + /* GPIO initialization */ + MCF_GPIO_PAR_UART |= 0x0FF0; + break; + case 2: + MCF_INTC0_ICR28 = 0x3; + MCF_INTC0_CIMR = 28; + /* GPIOs also must be initalized, depends on board */ + break; + } #else volatile unsigned char *icrp, *uartp; @@ -1574,7 +1596,7 @@ static void mcfrs_irqinit(struct mcf_serial *info) /* Clear mask, so no surprise interrupts. */ uartp[MCFUART_UIMR] = 0; - if (request_irq(info->irq, mcfrs_interrupt, SA_INTERRUPT, + if (request_irq(info->irq, mcfrs_interrupt, IRQF_DISABLED, "ColdFire UART", NULL)) { printk("MCFRS: Unable to attach ColdFire UART %d interrupt " "vector=%d\n", info->line, info->irq); @@ -1691,7 +1713,6 @@ mcfrs_init(void) /* Initialize the tty_driver structure */ mcfrs_serial_driver->owner = THIS_MODULE; mcfrs_serial_driver->name = "ttyS"; - mcfrs_serial_driver->devfs_name = "ttys/"; mcfrs_serial_driver->driver_name = "serial"; mcfrs_serial_driver->major = TTY_MAJOR; mcfrs_serial_driver->minor_start = 64; diff --git a/drivers/serial/mcfserial.h b/drivers/serial/mcfserial.h index a2b28e8629f9..56420e2cb110 100644 --- a/drivers/serial/mcfserial.h +++ b/drivers/serial/mcfserial.h @@ -14,7 +14,6 @@ #ifndef _MCF_SERIAL_H #define _MCF_SERIAL_H -#include <linux/config.h> #include <linux/serial.h> #ifdef __KERNEL__ diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index 1b2cdc91c228..7708e5dd3656 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -44,7 +44,6 @@ * will be mapped to. */ -#include <linux/config.h> #include <linux/platform_device.h> #include <linux/module.h> #include <linux/tty.h> @@ -191,7 +190,7 @@ mpc52xx_uart_startup(struct uart_port *port) /* Request IRQ */ ret = request_irq(port->irq, mpc52xx_uart_int, - SA_INTERRUPT | SA_SAMPLE_RANDOM, "mpc52xx_psc_uart", port); + IRQF_DISABLED | IRQF_SAMPLE_RANDOM, "mpc52xx_psc_uart", port); if (ret) return ret; @@ -693,7 +692,6 @@ static struct uart_driver mpc52xx_uart_driver = { .owner = THIS_MODULE, .driver_name = "mpc52xx_psc_uart", .dev_name = "ttyPSC", - .devfs_name = "ttyPSC", .major = SERIAL_PSC_MAJOR, .minor = SERIAL_PSC_MINOR, .nr = MPC52xx_PSC_MAXNUM, diff --git a/drivers/serial/mpsc.c b/drivers/serial/mpsc.c index 94681922ea0a..63d2a66e563b 100644 --- a/drivers/serial/mpsc.c +++ b/drivers/serial/mpsc.c @@ -50,7 +50,6 @@ * 4) AFAICT, hardware flow control isn't supported by the controller --MAG. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_MPSC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -315,7 +314,6 @@ struct mpsc_port_info *mpsc_device_remove(int index); #define MPSC_MAJOR 204 #define MPSC_MINOR_START 44 #define MPSC_DRIVER_NAME "MPSC" -#define MPSC_DEVFS_NAME "ttymm/" #define MPSC_DEV_NAME "ttyMM" #define MPSC_VERSION "1.00" @@ -1414,7 +1412,7 @@ mpsc_startup(struct uart_port *port) /* If irq's are shared, need to set flag */ if (mpsc_ports[0].port.irq == mpsc_ports[1].port.irq) - flag = SA_SHIRQ; + flag = IRQF_SHARED; if (request_irq(pi->port.irq, mpsc_sdma_intr, flag, "mpsc-sdma", pi)) @@ -1863,7 +1861,6 @@ static struct platform_driver mpsc_shared_driver = { static struct uart_driver mpsc_reg = { .owner = THIS_MODULE, .driver_name = MPSC_DRIVER_NAME, - .devfs_name = MPSC_DEVFS_NAME, .dev_name = MPSC_DEV_NAME, .major = MPSC_MAJOR, .minor = MPSC_MINOR_START, diff --git a/drivers/serial/mux.c b/drivers/serial/mux.c index 64c0e89124c9..4a1c9983f38f 100644 --- a/drivers/serial/mux.c +++ b/drivers/serial/mux.c @@ -16,7 +16,6 @@ ** */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/ioport.h> diff --git a/drivers/serial/pmac_zilog.c b/drivers/serial/pmac_zilog.c index 513ff8597707..bfd2a22759eb 100644 --- a/drivers/serial/pmac_zilog.c +++ b/drivers/serial/pmac_zilog.c @@ -42,7 +42,6 @@ #undef DEBUG_HARD #undef USE_CTRL_O_SYSRQ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> @@ -101,7 +100,6 @@ static DEFINE_MUTEX(pmz_irq_mutex); static struct uart_driver pmz_uart_reg = { .owner = THIS_MODULE, .driver_name = "ttyS", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, }; @@ -936,7 +934,7 @@ static int pmz_startup(struct uart_port *port) } pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON; - if (request_irq(uap->port.irq, pmz_interrupt, SA_SHIRQ, "PowerMac Zilog", uap)) { + if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED, "PowerMac Zilog", uap)) { dev_err(&uap->dev->ofdev.dev, "Unable to register zs interrupt handler.\n"); pmz_set_scc_power(uap, 0); @@ -1445,8 +1443,8 @@ static int __init pmz_init_port(struct uart_pmac_port *uap) uap->flags &= ~PMACZILOG_FLAG_HAS_DMA; goto no_dma; } - uap->tx_dma_irq = np->intrs[1].line; - uap->rx_dma_irq = np->intrs[2].line; + uap->tx_dma_irq = irq_of_parse_and_map(np, 1); + uap->rx_dma_irq = irq_of_parse_and_map(np, 2); } no_dma: @@ -1493,7 +1491,7 @@ no_dma: * Init remaining bits of "port" structure */ uap->port.iotype = UPIO_MEM; - uap->port.irq = np->intrs[0].line; + uap->port.irq = irq_of_parse_and_map(np, 0); uap->port.uartclk = ZS_CLOCK; uap->port.fifosize = 1; uap->port.ops = &pmz_pops; diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c index 77d4568ccc3a..a720953a404e 100644 --- a/drivers/serial/pxa.c +++ b/drivers/serial/pxa.c @@ -24,7 +24,6 @@ * with the serial core maintainer satisfaction to appear soon. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_PXA_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -269,7 +268,6 @@ static unsigned int serial_pxa_get_mctrl(struct uart_port *port) unsigned char status; unsigned int ret; -return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; status = serial_in(up, UART_MSR); ret = 0; @@ -391,7 +389,7 @@ static int serial_pxa_startup(struct uart_port *port) /* * Finally, enable interrupts. Note: Modem status interrupts - * are set via set_termios(), which will be occuring imminently + * are set via set_termios(), which will be occurring imminently * anyway, so we don't enable them here. */ up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE | UART_IER_UUE; @@ -781,7 +779,6 @@ static struct uart_pxa_port serial_pxa_ports[] = { static struct uart_driver serial_pxa_reg = { .owner = THIS_MODULE, .driver_name = "PXA serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = 64, diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index f5aac92fb798..392bffcf96e8 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -55,7 +55,6 @@ * BJD, 04-Nov-2004 */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_S3C2410_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -149,7 +148,6 @@ s3c24xx_serial_dbg(const char *fmt, ...) /* UART name and device definitions */ #define S3C24XX_SERIAL_NAME "ttySAC" -#define S3C24XX_SERIAL_DEVFS "tts/" #define S3C24XX_SERIAL_MAJOR 204 #define S3C24XX_SERIAL_MINOR 64 @@ -872,6 +870,8 @@ static const char *s3c24xx_serial_type(struct uart_port *port) return "S3C2410"; case PORT_S3C2440: return "S3C2440"; + case PORT_S3C2412: + return "S3C2412"; default: return NULL; } @@ -950,7 +950,6 @@ static struct uart_driver s3c24xx_uart_drv = { .nr = 3, .cons = S3C24XX_SERIAL_CONSOLE, .driver_name = S3C24XX_SERIAL_NAME, - .devfs_name = S3C24XX_SERIAL_DEVFS, .major = S3C24XX_SERIAL_MAJOR, .minor = S3C24XX_SERIAL_MINOR, }; @@ -1365,7 +1364,7 @@ static inline void s3c2410_serial_exit(void) #endif /* CONFIG_CPU_S3C2410 */ -#ifdef CONFIG_CPU_S3C2440 +#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) static int s3c2440_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *clk) @@ -1528,6 +1527,141 @@ static inline void s3c2440_serial_exit(void) #define s3c2440_uart_inf_at NULL #endif /* CONFIG_CPU_S3C2440 */ +#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413) + +static int s3c2412_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + ucon &= ~S3C2412_UCON_CLKMASK; + + if (strcmp(clk->name, "uclk") == 0) + ucon |= S3C2440_UCON_UCLK; + else if (strcmp(clk->name, "pclk") == 0) + ucon |= S3C2440_UCON_PCLK; + else if (strcmp(clk->name, "usysclk") == 0) + ucon |= S3C2412_UCON_USYSCLK; + else { + printk(KERN_ERR "unknown clock source %s\n", clk->name); + return -EINVAL; + } + + wr_regl(port, S3C2410_UCON, ucon); + return 0; +} + + +static int s3c2412_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + switch (ucon & S3C2412_UCON_CLKMASK) { + case S3C2412_UCON_UCLK: + clk->divisor = 1; + clk->name = "uclk"; + break; + + case S3C2412_UCON_PCLK: + case S3C2412_UCON_PCLK2: + clk->divisor = 1; + clk->name = "pclk"; + break; + + case S3C2412_UCON_USYSCLK: + clk->divisor = 1; + clk->name = "usysclk"; + break; + } + + return 0; +} + +static int s3c2412_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + dbg("%s: port=%p (%08lx), cfg=%p\n", + __FUNCTION__, port, port->mapbase, cfg); + + /* ensure we don't change the clock settings... */ + + ucon &= S3C2412_UCON_CLKMASK; + + wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2412_uart_inf = { + .name = "Samsung S3C2412 UART", + .type = PORT_S3C2412, + .fifosize = 64, + .rx_fifomask = S3C2440_UFSTAT_RXMASK, + .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2440_UFSTAT_RXFULL, + .tx_fifofull = S3C2440_UFSTAT_TXFULL, + .tx_fifomask = S3C2440_UFSTAT_TXMASK, + .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, + .get_clksrc = s3c2412_serial_getsource, + .set_clksrc = s3c2412_serial_setsource, + .reset_port = s3c2412_serial_resetport, +}; + +/* device management */ + +static int s3c2412_serial_probe(struct platform_device *dev) +{ + dbg("s3c2440_serial_probe: dev=%p\n", dev); + return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); +} + +static struct platform_driver s3c2412_serial_drv = { + .probe = s3c2412_serial_probe, + .remove = s3c24xx_serial_remove, + .suspend = s3c24xx_serial_suspend, + .resume = s3c24xx_serial_resume, + .driver = { + .name = "s3c2412-uart", + .owner = THIS_MODULE, + }, +}; + + +static inline int s3c2412_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); +} + +static inline void s3c2412_serial_exit(void) +{ + platform_driver_unregister(&s3c2412_serial_drv); +} + +#define s3c2412_uart_inf_at &s3c2412_uart_inf +#else + +static inline int s3c2412_serial_init(void) +{ + return 0; +} + +static inline void s3c2412_serial_exit(void) +{ +} + +#define s3c2412_uart_inf_at NULL +#endif /* CONFIG_CPU_S3C2440 */ + + /* module initialisation code */ static int __init s3c24xx_serial_modinit(void) @@ -1542,6 +1676,7 @@ static int __init s3c24xx_serial_modinit(void) s3c2400_serial_init(); s3c2410_serial_init(); + s3c2412_serial_init(); s3c2440_serial_init(); return 0; @@ -1551,6 +1686,7 @@ static void __exit s3c24xx_serial_modexit(void) { s3c2400_serial_exit(); s3c2410_serial_exit(); + s3c2412_serial_exit(); s3c2440_serial_exit(); uart_unregister_driver(&s3c24xx_uart_drv); @@ -1773,6 +1909,8 @@ static int s3c24xx_serial_initconsole(void) info = s3c2410_uart_inf_at; } else if (strcmp(dev->name, "s3c2440-uart") == 0) { info = s3c2440_uart_inf_at; + } else if (strcmp(dev->name, "s3c2412-uart") == 0) { + info = s3c2412_uart_inf_at; } else { printk(KERN_ERR "s3c24xx: no driver for %s\n", dev->name); return 0; @@ -1796,4 +1934,4 @@ console_initcall(s3c24xx_serial_initconsole); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); -MODULE_DESCRIPTION("Samsung S3C2410/S3C2440 Serial port driver"); +MODULE_DESCRIPTION("Samsung S3C2410/S3C2440/S3C2412 Serial port driver"); diff --git a/drivers/serial/sa1100.c b/drivers/serial/sa1100.c index c2d9068b491d..db3486d33870 100644 --- a/drivers/serial/sa1100.c +++ b/drivers/serial/sa1100.c @@ -24,7 +24,6 @@ * $Id: sa1100.c,v 1.50 2002/07/29 14:41:04 rmk Exp $ * */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_SA1100_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -816,7 +815,6 @@ static struct uart_driver sa1100_reg = { .owner = THIS_MODULE, .driver_name = "ttySA", .dev_name = "ttySA", - .devfs_name = "ttySA", .major = SERIAL_SA1100_MAJOR, .minor = MINOR_START, .nr = NR_PORTS, diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 3805f467b2f5..d5f636fbf29a 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -22,7 +22,6 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include <linux/config.h> #include <linux/module.h> #include <linux/tty.h> #include <linux/slab.h> @@ -50,6 +49,12 @@ */ static DEFINE_MUTEX(port_mutex); +/* + * lockdep: port->lock is initialized in two places, but we + * want only one lock-class: + */ +static struct lock_class_key port_lock_key; + #define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8) #define uart_users(state) ((state)->count + ((state)->info ? (state)->info->blocked_open : 0)) @@ -1868,6 +1873,7 @@ uart_set_options(struct uart_port *port, struct console *co, * early. */ spin_lock_init(&port->lock); + lockdep_set_class(&port->lock, &port_lock_key); memset(&termios, 0, sizeof(struct termios)); @@ -2155,7 +2161,6 @@ int uart_register_driver(struct uart_driver *drv) normal->owner = drv->owner; normal->driver_name = drv->driver_name; - normal->devfs_name = drv->devfs_name; normal->name = drv->dev_name; normal->major = drv->major; normal->minor_start = drv->minor; @@ -2163,7 +2168,7 @@ int uart_register_driver(struct uart_driver *drv) normal->subtype = SERIAL_TYPE_NORMAL; normal->init_termios = tty_std_termios; normal->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; - normal->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS; + normal->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; normal->driver_state = drv; tty_set_operations(normal, &uart_ops); @@ -2251,8 +2256,10 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port) * If this port is a console, then the spinlock is already * initialised. */ - if (!(uart_console(port) && (port->cons->flags & CON_ENABLED))) + if (!(uart_console(port) && (port->cons->flags & CON_ENABLED))) { spin_lock_init(&port->lock); + lockdep_set_class(&port->lock, &port_lock_key); + } uart_configure_port(drv, state, port); @@ -2314,7 +2321,7 @@ int uart_remove_one_port(struct uart_driver *drv, struct uart_port *port) mutex_unlock(&state->mutex); /* - * Remove the devices from devfs + * Remove the devices from the tty layer */ tty_unregister_device(drv->tty_driver, port->line); diff --git a/drivers/serial/serial_cs.c b/drivers/serial/serial_cs.c index 2c70773543e0..cbf260bc225d 100644 --- a/drivers/serial/serial_cs.c +++ b/drivers/serial/serial_cs.c @@ -786,6 +786,7 @@ static struct pcmcia_device_id serial_ids[] = { PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "COMpad4.cis"), PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "COMpad2.cis"), PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "RS-COM-2P.cis"), + PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "GLOBETROTTER.cis"), /* too generic */ /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */ /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */ diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c index aa521b8e0d4e..23ddedbaec08 100644 --- a/drivers/serial/serial_lh7a40x.c +++ b/drivers/serial/serial_lh7a40x.c @@ -27,7 +27,6 @@ * */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -145,14 +144,15 @@ lh7a40xuart_rx_chars (struct uart_port* port) { struct tty_struct* tty = port->info->tty; int cbRxMax = 256; /* (Gross) limit on receive */ - unsigned int data, flag;/* Received data and status */ + unsigned int data; /* Received data and status */ + unsigned int flag; while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) { data = UR (port, UART_R_DATA); flag = TTY_NORMAL; ++port->icount.rx; - if (unlikely(data & RxError)) { /* Quick check, short-circuit */ + if (unlikely(data & RxError)) { if (data & RxBreak) { data &= ~(RxFramingError | RxParityError); ++port->icount.brk; @@ -303,7 +303,7 @@ static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl) /* Note, kernel appears to be setting DTR and RTS on console. */ /* *** FIXME: this deserves more work. There's some work in - tracing all of the IO pins. */ + tracing all of the IO pins. */ #if 0 if( port->mapbase == UART1_PHYS) { gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS); @@ -662,9 +662,13 @@ static int __init lh7a40xuart_init(void) if (ret == 0) { int i; - for (i = 0; i < DEV_NR; i++) + for (i = 0; i < DEV_NR; i++) { + /* UART3, when used, requires GPIO pin reallocation */ + if (lh7a40x_ports[i].port.mapbase == UART3_PHYS) + GPIO_PINMUX |= 1<<3; uart_add_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port); + } } return ret; } diff --git a/drivers/serial/serial_txx9.c b/drivers/serial/serial_txx9.c index 3bdee64d1a99..b361669f85a1 100644 --- a/drivers/serial/serial_txx9.c +++ b/drivers/serial/serial_txx9.c @@ -38,7 +38,6 @@ * Fix some spin_locks. * Do not call uart_add_one_port for absent ports. */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -69,12 +68,10 @@ static char *serial_name = "TX39/49 Serial driver"; #if !defined(CONFIG_SERIAL_TXX9_STDSERIAL) /* "ttyS" is used for standard serial driver */ #define TXX9_TTY_NAME "ttyTX" -#define TXX9_TTY_DEVFS_NAME "tttx/" #define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */ #else /* acts like standard serial driver */ #define TXX9_TTY_NAME "ttyS" -#define TXX9_TTY_DEVFS_NAME "tts/" #define TXX9_TTY_MINOR_START 64 #endif #define TXX9_TTY_MAJOR TTY_MAJOR @@ -498,7 +495,7 @@ static int serial_txx9_startup(struct uart_port *port) sio_out(up, TXX9_SIDISR, 0); retval = request_irq(up->port.irq, serial_txx9_interrupt, - SA_SHIRQ, "serial_txx9", up); + IRQF_SHARED, "serial_txx9", up); if (retval) return retval; @@ -971,7 +968,6 @@ console_initcall(serial_txx9_console_init); static struct uart_driver serial_txx9_reg = { .owner = THIS_MODULE, .driver_name = "serial_txx9", - .devfs_name = TXX9_TTY_DEVFS_NAME, .dev_name = TXX9_TTY_NAME, .major = TXX9_TTY_MAJOR, .minor = TXX9_TTY_MINOR_START, diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index 44f6bf79bbe1..301573373c30 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -20,7 +20,6 @@ #undef DEBUG -#include <linux/config.h> #include <linux/module.h> #include <linux/errno.h> #include <linux/signal.h> @@ -842,7 +841,7 @@ static int sci_request_irq(struct sci_port *port) printk(KERN_ERR "sci: Cannot allocate irq.(IRQ=0)\n"); return -ENODEV; } - if (request_irq(port->irqs[0], sci_mpxed_interrupt, SA_INTERRUPT, + if (request_irq(port->irqs[0], sci_mpxed_interrupt, IRQF_DISABLED, "sci", port)) { printk(KERN_ERR "sci: Cannot allocate irq.\n"); return -ENODEV; @@ -851,7 +850,7 @@ static int sci_request_irq(struct sci_port *port) for (i = 0; i < ARRAY_SIZE(handlers); i++) { if (!port->irqs[i]) continue; - if (request_irq(port->irqs[i], handlers[i], SA_INTERRUPT, + if (request_irq(port->irqs[i], handlers[i], IRQF_DISABLED, desc[i], port)) { printk(KERN_ERR "sci: Cannot allocate irq.\n"); return -ENODEV; @@ -1699,9 +1698,6 @@ static char banner[] __initdata = static struct uart_driver sci_uart_driver = { .owner = THIS_MODULE, .driver_name = "sci", -#ifdef CONFIG_DEVFS_FS - .devfs_name = "ttsc/", -#endif .dev_name = "ttySC", .major = SCI_MAJOR, .minor = SCI_MINOR_START, diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h index 1f14bb4382f6..ab320fa3237c 100644 --- a/drivers/serial/sh-sci.h +++ b/drivers/serial/sh-sci.h @@ -10,7 +10,6 @@ * Modified to support SH7300(SH-Mobile) SCIF. Takashi Kusuda (Jun 2003). * Modified to support H8/300 Series Yoshinori Sato (Feb 2004). */ -#include <linux/config.h> #include <linux/serial_core.h> #if defined(__H8300H__) || defined(__H8300S__) diff --git a/drivers/serial/sn_console.c b/drivers/serial/sn_console.c index 60ea4a3f0713..2f148e5b9255 100644 --- a/drivers/serial/sn_console.c +++ b/drivers/serial/sn_console.c @@ -37,7 +37,6 @@ * http://oss.sgi.com/projects/GenInfo/NoticeExplan */ -#include <linux/config.h> #include <linux/interrupt.h> #include <linux/tty.h> #include <linux/serial.h> @@ -649,7 +648,7 @@ static irqreturn_t sn_sal_interrupt(int irq, void *dev_id, struct pt_regs *regs) static int sn_sal_connect_interrupt(struct sn_cons_port *port) { if (request_irq(SGI_UART_VECTOR, sn_sal_interrupt, - SA_INTERRUPT | SA_SHIRQ, + IRQF_DISABLED | IRQF_SHARED, "SAL console driver", port) >= 0) { return SGI_UART_VECTOR; } diff --git a/drivers/serial/suncore.c b/drivers/serial/suncore.c index fa4ae94243c2..e35d9ab359f1 100644 --- a/drivers/serial/suncore.c +++ b/drivers/serial/suncore.c @@ -10,7 +10,6 @@ * Copyright (C) 2002 David S. Miller (davem@redhat.com) */ -#include <linux/config.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/console.h> diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c index f137804b3133..f851f0f44f9b 100644 --- a/drivers/serial/sunhv.c +++ b/drivers/serial/sunhv.c @@ -20,8 +20,8 @@ #include <asm/hypervisor.h> #include <asm/spitfire.h> -#include <asm/vdev.h> -#include <asm/oplib.h> +#include <asm/prom.h> +#include <asm/of_device.h> #include <asm/irq.h> #if defined(CONFIG_MAGIC_SYSRQ) @@ -353,7 +353,6 @@ static struct uart_ops sunhv_pops = { static struct uart_driver sunhv_reg = { .owner = THIS_MODULE, .driver_name = "serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, }; @@ -408,143 +407,120 @@ static inline struct console *SUNHV_CONSOLE(void) return &sunhv_console; } -static int __init hv_console_compatible(char *buf, int len) -{ - while (len) { - int this_len; - - if (!strcmp(buf, "qcn")) - return 1; - - this_len = strlen(buf) + 1; - - buf += this_len; - len -= this_len; - } - - return 0; -} - -static unsigned int __init get_interrupt(void) -{ - const char *cons_str = "console"; - const char *compat_str = "compatible"; - int node = prom_getchild(sun4v_vdev_root); - char buf[64]; - int err, len; - - node = prom_searchsiblings(node, cons_str); - if (!node) - return 0; - - len = prom_getproplen(node, compat_str); - if (len == 0 || len == -1) - return 0; - - err = prom_getproperty(node, compat_str, buf, 64); - if (err == -1) - return 0; - - if (!hv_console_compatible(buf, len)) - return 0; - - /* Ok, the this is the OBP node for the sun4v hypervisor - * console device. Decode the interrupt. - */ - return sun4v_vdev_device_interrupt(node); -} - -static int __init sunhv_init(void) +static int __devinit hv_probe(struct of_device *op, const struct of_device_id *match) { struct uart_port *port; - int ret; + int err; - if (tlb_type != hypervisor) + if (op->irqs[0] == 0xffffffff) return -ENODEV; - port = kmalloc(sizeof(struct uart_port), GFP_KERNEL); + port = kzalloc(sizeof(struct uart_port), GFP_KERNEL); if (unlikely(!port)) return -ENOMEM; - memset(port, 0, sizeof(struct uart_port)); + sunhv_port = port; port->line = 0; port->ops = &sunhv_pops; port->type = PORT_SUNHV; port->uartclk = ( 29491200 / 16 ); /* arbitrary */ - /* Set this just to make uart_configure_port() happy. */ port->membase = (unsigned char __iomem *) __pa(port); - port->irq = get_interrupt(); - if (!port->irq) { - kfree(port); - return -ENODEV; - } + port->irq = op->irqs[0]; + + port->dev = &op->dev; sunhv_reg.minor = sunserial_current_minor; sunhv_reg.nr = 1; - ret = uart_register_driver(&sunhv_reg); - if (ret < 0) { - printk(KERN_ERR "SUNHV: uart_register_driver() failed %d\n", - ret); - kfree(port); - - return ret; - } + err = uart_register_driver(&sunhv_reg); + if (err) + goto out_free_port; sunhv_reg.tty_driver->name_base = sunhv_reg.minor - 64; sunserial_current_minor += 1; sunhv_reg.cons = SUNHV_CONSOLE(); - sunhv_port = port; + err = uart_add_one_port(&sunhv_reg, port); + if (err) + goto out_unregister_driver; - ret = uart_add_one_port(&sunhv_reg, port); - if (ret < 0) { - printk(KERN_ERR "SUNHV: uart_add_one_port() failed %d\n", ret); - sunserial_current_minor -= 1; - uart_unregister_driver(&sunhv_reg); - kfree(port); - sunhv_port = NULL; - return -ENODEV; - } + err = request_irq(port->irq, sunhv_interrupt, 0, "hvcons", port); + if (err) + goto out_remove_port; - if (request_irq(port->irq, sunhv_interrupt, - SA_SHIRQ, "serial(sunhv)", port)) { - printk(KERN_ERR "sunhv: Cannot register IRQ\n"); - uart_remove_one_port(&sunhv_reg, port); - sunserial_current_minor -= 1; - uart_unregister_driver(&sunhv_reg); - kfree(port); - sunhv_port = NULL; - return -ENODEV; - } + dev_set_drvdata(&op->dev, port); return 0; + +out_remove_port: + uart_remove_one_port(&sunhv_reg, port); + +out_unregister_driver: + sunserial_current_minor -= 1; + uart_unregister_driver(&sunhv_reg); + +out_free_port: + kfree(port); + sunhv_port = NULL; + return err; } -static void __exit sunhv_exit(void) +static int __devexit hv_remove(struct of_device *dev) { - struct uart_port *port = sunhv_port; - - BUG_ON(!port); + struct uart_port *port = dev_get_drvdata(&dev->dev); free_irq(port->irq, port); uart_remove_one_port(&sunhv_reg, port); - sunserial_current_minor -= 1; + sunserial_current_minor -= 1; uart_unregister_driver(&sunhv_reg); - kfree(sunhv_port); + kfree(port); sunhv_port = NULL; + + dev_set_drvdata(&dev->dev, NULL); + + return 0; +} + +static struct of_device_id hv_match[] = { + { + .name = "console", + .compatible = "qcn", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, hv_match); + +static struct of_platform_driver hv_driver = { + .name = "hv", + .match_table = hv_match, + .probe = hv_probe, + .remove = __devexit_p(hv_remove), +}; + +static int __init sunhv_init(void) +{ + if (tlb_type != hypervisor) + return -ENODEV; + + return of_register_driver(&hv_driver, &of_bus_type); +} + +static void __exit sunhv_exit(void) +{ + of_unregister_driver(&hv_driver); } module_init(sunhv_init); module_exit(sunhv_exit); MODULE_AUTHOR("David S. Miller"); -MODULE_DESCRIPTION("SUN4V Hypervisor console driver") +MODULE_DESCRIPTION("SUN4V Hypervisor console driver"); +MODULE_VERSION("2.0"); MODULE_LICENSE("GPL"); diff --git a/drivers/serial/sunsab.c b/drivers/serial/sunsab.c index bfbe9dc90cca..0dbd4df44c05 100644 --- a/drivers/serial/sunsab.c +++ b/drivers/serial/sunsab.c @@ -1,7 +1,7 @@ /* sunsab.c: ASYNC Driver for the SIEMENS SAB82532 DUSCC. * * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) - * Copyright (C) 2002 David S. Miller (davem@redhat.com) + * Copyright (C) 2002, 2006 David S. Miller (davem@davemloft.net) * * Rewrote buffer handling to use CIRC(Circular Buffer) macros. * Maxim Krasnyanskiy <maxk@qualcomm.com> @@ -12,10 +12,9 @@ * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 * * Ported to new 2.5.x UART layer. - * David S. Miller <davem@redhat.com> + * David S. Miller <davem@davemloft.net> */ -#include <linux/config.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/sched.h> @@ -37,8 +36,8 @@ #include <asm/io.h> #include <asm/irq.h> -#include <asm/oplib.h> -#include <asm/ebus.h> +#include <asm/prom.h> +#include <asm/of_device.h> #if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -851,7 +850,6 @@ static struct uart_ops sunsab_pops = { static struct uart_driver sunsab_reg = { .owner = THIS_MODULE, .driver_name = "serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, }; @@ -977,199 +975,188 @@ static inline struct console *SUNSAB_CONSOLE(void) #define sunsab_console_init() do { } while (0) #endif -static void __init for_each_sab_edev(void (*callback)(struct linux_ebus_device *, void *), void *arg) +static int __devinit sunsab_init_one(struct uart_sunsab_port *up, + struct of_device *op, + unsigned long offset, + int line) { - struct linux_ebus *ebus; - struct linux_ebus_device *edev = NULL; - - for_each_ebus(ebus) { - for_each_ebusdev(edev, ebus) { - if (!strcmp(edev->prom_name, "se")) { - callback(edev, arg); - continue; - } else if (!strcmp(edev->prom_name, "serial")) { - char compat[32]; - int clen; - - /* On RIO this can be an SE, check it. We could - * just check ebus->is_rio, but this is more portable. - */ - clen = prom_getproperty(edev->prom_node, "compatible", - compat, sizeof(compat)); - if (clen > 0) { - if (strncmp(compat, "sab82532", 8) == 0) { - callback(edev, arg); - continue; - } - } - } - } - } -} + up->port.line = line; + up->port.dev = &op->dev; + + up->port.mapbase = op->resource[0].start + offset; + up->port.membase = of_ioremap(&op->resource[0], offset, + sizeof(union sab82532_async_regs), + "sab"); + if (!up->port.membase) + return -ENOMEM; + up->regs = (union sab82532_async_regs __iomem *) up->port.membase; -static void __init sab_count_callback(struct linux_ebus_device *edev, void *arg) -{ - int *count_p = arg; + up->port.irq = op->irqs[0]; - (*count_p)++; -} + up->port.fifosize = SAB82532_XMIT_FIFO_SIZE; + up->port.iotype = UPIO_MEM; -static void __init sab_attach_callback(struct linux_ebus_device *edev, void *arg) -{ - int *instance_p = arg; - struct uart_sunsab_port *up; - unsigned long regs, offset; - int i; + writeb(SAB82532_IPC_IC_ACT_LOW, &up->regs->w.ipc); - /* Note: ports are located in reverse order */ - regs = edev->resource[0].start; - offset = sizeof(union sab82532_async_regs); - for (i = 0; i < 2; i++) { - up = &sunsab_ports[(*instance_p * 2) + 1 - i]; + up->port.ops = &sunsab_pops; + up->port.type = PORT_SUNSAB; + up->port.uartclk = SAB_BASE_BAUD; - memset(up, 0, sizeof(*up)); - up->regs = ioremap(regs + offset, sizeof(union sab82532_async_regs)); - up->port.irq = edev->irqs[0]; - up->port.fifosize = SAB82532_XMIT_FIFO_SIZE; - up->port.mapbase = (unsigned long)up->regs; - up->port.iotype = UPIO_MEM; + up->type = readb(&up->regs->r.vstr) & 0x0f; + writeb(~((1 << 1) | (1 << 2) | (1 << 4)), &up->regs->w.pcr); + writeb(0xff, &up->regs->w.pim); + if ((up->port.line & 0x1) == 0) { + up->pvr_dsr_bit = (1 << 0); + up->pvr_dtr_bit = (1 << 1); + } else { + up->pvr_dsr_bit = (1 << 3); + up->pvr_dtr_bit = (1 << 2); + } + up->cached_pvr = (1 << 1) | (1 << 2) | (1 << 4); + writeb(up->cached_pvr, &up->regs->w.pvr); + up->cached_mode = readb(&up->regs->rw.mode); + up->cached_mode |= SAB82532_MODE_FRTS; + writeb(up->cached_mode, &up->regs->rw.mode); + up->cached_mode |= SAB82532_MODE_RTS; + writeb(up->cached_mode, &up->regs->rw.mode); - writeb(SAB82532_IPC_IC_ACT_LOW, &up->regs->w.ipc); + up->tec_timeout = SAB82532_MAX_TEC_TIMEOUT; + up->cec_timeout = SAB82532_MAX_CEC_TIMEOUT; - offset -= sizeof(union sab82532_async_regs); + if (!(up->port.line & 0x01)) { + int err; + + err = request_irq(up->port.irq, sunsab_interrupt, + IRQF_SHARED, "sab", up); + if (err) { + of_iounmap(up->port.membase, + sizeof(union sab82532_async_regs)); + return err; + } } - - (*instance_p)++; + + return 0; } -static int __init probe_for_sabs(void) +static int __devinit sab_probe(struct of_device *op, const struct of_device_id *match) { - int this_sab = 0; + static int inst; + struct uart_sunsab_port *up; + int err; + + up = &sunsab_ports[inst * 2]; + + err = sunsab_init_one(&up[0], op, + sizeof(union sab82532_async_regs), + (inst * 2) + 0); + if (err) + return err; + + err = sunsab_init_one(&up[0], op, 0, + (inst * 2) + 1); + if (err) { + of_iounmap(up[0].port.membase, + sizeof(union sab82532_async_regs)); + free_irq(up[0].port.irq, &up[0]); + return err; + } - /* Find device instances. */ - for_each_sab_edev(&sab_count_callback, &this_sab); - if (!this_sab) - return -ENODEV; + uart_add_one_port(&sunsab_reg, &up[0].port); + uart_add_one_port(&sunsab_reg, &up[1].port); - /* Allocate tables. */ - sunsab_ports = kmalloc(sizeof(struct uart_sunsab_port) * this_sab * 2, - GFP_KERNEL); - if (!sunsab_ports) - return -ENOMEM; + dev_set_drvdata(&op->dev, &up[0]); - num_channels = this_sab * 2; + inst++; - this_sab = 0; - for_each_sab_edev(&sab_attach_callback, &this_sab); return 0; } -static void __init sunsab_init_hw(void) +static void __devexit sab_remove_one(struct uart_sunsab_port *up) { - int i; - - for (i = 0; i < num_channels; i++) { - struct uart_sunsab_port *up = &sunsab_ports[i]; - - up->port.line = i; - up->port.ops = &sunsab_pops; - up->port.type = PORT_SUNSAB; - up->port.uartclk = SAB_BASE_BAUD; - - up->type = readb(&up->regs->r.vstr) & 0x0f; - writeb(~((1 << 1) | (1 << 2) | (1 << 4)), &up->regs->w.pcr); - writeb(0xff, &up->regs->w.pim); - if (up->port.line == 0) { - up->pvr_dsr_bit = (1 << 0); - up->pvr_dtr_bit = (1 << 1); - } else { - up->pvr_dsr_bit = (1 << 3); - up->pvr_dtr_bit = (1 << 2); - } - up->cached_pvr = (1 << 1) | (1 << 2) | (1 << 4); - writeb(up->cached_pvr, &up->regs->w.pvr); - up->cached_mode = readb(&up->regs->rw.mode); - up->cached_mode |= SAB82532_MODE_FRTS; - writeb(up->cached_mode, &up->regs->rw.mode); - up->cached_mode |= SAB82532_MODE_RTS; - writeb(up->cached_mode, &up->regs->rw.mode); - - up->tec_timeout = SAB82532_MAX_TEC_TIMEOUT; - up->cec_timeout = SAB82532_MAX_CEC_TIMEOUT; - - if (!(up->port.line & 0x01)) { - if (request_irq(up->port.irq, sunsab_interrupt, - SA_SHIRQ, "serial(sab82532)", up)) { - printk("sunsab%d: can't get IRQ %x\n", - i, up->port.irq); - continue; - } - } - } + uart_remove_one_port(&sunsab_reg, &up->port); + if (!(up->port.line & 1)) + free_irq(up->port.irq, up); + of_iounmap(up->port.membase, + sizeof(union sab82532_async_regs)); } -static int __init sunsab_init(void) +static int __devexit sab_remove(struct of_device *op) { - int ret = probe_for_sabs(); - int i; - - if (ret < 0) - return ret; + struct uart_sunsab_port *up = dev_get_drvdata(&op->dev); - sunsab_init_hw(); + sab_remove_one(&up[0]); + sab_remove_one(&up[1]); - sunsab_reg.minor = sunserial_current_minor; - sunsab_reg.nr = num_channels; + dev_set_drvdata(&op->dev, NULL); - ret = uart_register_driver(&sunsab_reg); - if (ret < 0) { - int i; + return 0; +} - for (i = 0; i < num_channels; i++) { - struct uart_sunsab_port *up = &sunsab_ports[i]; +static struct of_device_id sab_match[] = { + { + .name = "se", + }, + { + .name = "serial", + .compatible = "sab82532", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, sab_match); - if (!(up->port.line & 0x01)) - free_irq(up->port.irq, up); - iounmap(up->regs); - } - kfree(sunsab_ports); - sunsab_ports = NULL; +static struct of_platform_driver sab_driver = { + .name = "sab", + .match_table = sab_match, + .probe = sab_probe, + .remove = __devexit_p(sab_remove), +}; - return ret; +static int __init sunsab_init(void) +{ + struct device_node *dp; + int err; + + num_channels = 0; + for_each_node_by_name(dp, "su") + num_channels += 2; + for_each_node_by_name(dp, "serial") { + if (of_device_is_compatible(dp, "sab82532")) + num_channels += 2; } - sunsab_reg.tty_driver->name_base = sunsab_reg.minor - 64; + if (num_channels) { + sunsab_ports = kzalloc(sizeof(struct uart_sunsab_port) * + num_channels, GFP_KERNEL); + if (!sunsab_ports) + return -ENOMEM; - sunsab_reg.cons = SUNSAB_CONSOLE(); + sunsab_reg.minor = sunserial_current_minor; + sunsab_reg.nr = num_channels; - sunserial_current_minor += num_channels; - - for (i = 0; i < num_channels; i++) { - struct uart_sunsab_port *up = &sunsab_ports[i]; + err = uart_register_driver(&sunsab_reg); + if (err) { + kfree(sunsab_ports); + sunsab_ports = NULL; - uart_add_one_port(&sunsab_reg, &up->port); + return err; + } + + sunsab_reg.tty_driver->name_base = sunsab_reg.minor - 64; + sunsab_reg.cons = SUNSAB_CONSOLE(); + sunserial_current_minor += num_channels; } - return 0; + return of_register_driver(&sab_driver, &of_bus_type); } static void __exit sunsab_exit(void) { - int i; - - for (i = 0; i < num_channels; i++) { - struct uart_sunsab_port *up = &sunsab_ports[i]; - - uart_remove_one_port(&sunsab_reg, &up->port); - - if (!(up->port.line & 0x01)) - free_irq(up->port.irq, up); - iounmap(up->regs); + of_unregister_driver(&sab_driver); + if (num_channels) { + sunserial_current_minor -= num_channels; + uart_unregister_driver(&sunsab_reg); } - sunserial_current_minor -= num_channels; - uart_unregister_driver(&sunsab_reg); - kfree(sunsab_ports); sunsab_ports = NULL; } diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index 2b4f96541b8e..f9013baba05b 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -12,10 +12,9 @@ * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 * * Converted to new 2.5.x UART layer. - * David S. Miller (davem@redhat.com), 2002-Jul-29 + * David S. Miller (davem@davemloft.net), 2002-Jul-29 */ -#include <linux/config.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/sched.h> @@ -40,11 +39,8 @@ #include <asm/io.h> #include <asm/irq.h> -#include <asm/oplib.h> -#include <asm/ebus.h> -#ifdef CONFIG_SPARC64 -#include <asm/isa.h> -#endif +#include <asm/prom.h> +#include <asm/of_device.h> #if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -94,10 +90,10 @@ struct uart_sunsu_port { /* Probing information. */ enum su_type su_type; unsigned int type_probed; /* XXX Stupid */ - int port_node; + unsigned long reg_size; #ifdef CONFIG_SERIO - struct serio *serio; + struct serio serio; int serio_open; #endif }; @@ -509,7 +505,7 @@ static void receive_kbd_ms_chars(struct uart_sunsu_port *up, struct pt_regs *reg /* Stop-A is handled by drivers/char/keyboard.c now. */ if (up->su_type == SU_PORT_KBD) { #ifdef CONFIG_SERIO - serio_interrupt(up->serio, ch, 0, regs); + serio_interrupt(&up->serio, ch, 0, regs); #endif } else if (up->su_type == SU_PORT_MS) { int ret = suncore_mouse_baud_detection(ch, is_break); @@ -523,7 +519,7 @@ static void receive_kbd_ms_chars(struct uart_sunsu_port *up, struct pt_regs *reg case 0: #ifdef CONFIG_SERIO - serio_interrupt(up->serio, ch, 0, regs); + serio_interrupt(&up->serio, ch, 0, regs); #endif break; }; @@ -671,10 +667,10 @@ static int sunsu_startup(struct uart_port *port) if (up->su_type != SU_PORT_PORT) { retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt, - SA_SHIRQ, su_typev[up->su_type], up); + IRQF_SHARED, su_typev[up->su_type], up); } else { retval = request_irq(up->port.irq, sunsu_serial_interrupt, - SA_SHIRQ, su_typev[up->su_type], up); + IRQF_SHARED, su_typev[up->su_type], up); } if (retval) { printk("su: Cannot register IRQ %d\n", up->port.irq); @@ -1031,99 +1027,14 @@ static void sunsu_autoconfig(struct uart_sunsu_port *up) { unsigned char status1, status2, scratch, scratch2, scratch3; unsigned char save_lcr, save_mcr; - struct linux_ebus_device *dev = NULL; - struct linux_ebus *ebus; -#ifdef CONFIG_SPARC64 - struct sparc_isa_bridge *isa_br; - struct sparc_isa_device *isa_dev; -#endif -#ifndef CONFIG_SPARC64 - struct linux_prom_registers reg0; -#endif unsigned long flags; - if (!up->port_node || !up->su_type) + if (up->su_type == SU_PORT_NONE) return; up->type_probed = PORT_UNKNOWN; up->port.iotype = UPIO_MEM; - /* - * First we look for Ebus-bases su's - */ - for_each_ebus(ebus) { - for_each_ebusdev(dev, ebus) { - if (dev->prom_node == up->port_node) { - /* - * The EBus is broken on sparc; it delivers - * virtual addresses in resources. Oh well... - * This is correct on sparc64, though. - */ - up->port.membase = (char *) dev->resource[0].start; - /* - * This is correct on both architectures. - */ - up->port.mapbase = dev->resource[0].start; - up->port.irq = dev->irqs[0]; - goto ebus_done; - } - } - } - -#ifdef CONFIG_SPARC64 - for_each_isa(isa_br) { - for_each_isadev(isa_dev, isa_br) { - if (isa_dev->prom_node == up->port_node) { - /* Same on sparc64. Cool architecure... */ - up->port.membase = (char *) isa_dev->resource.start; - up->port.mapbase = isa_dev->resource.start; - up->port.irq = isa_dev->irq; - goto ebus_done; - } - } - } -#endif - -#ifdef CONFIG_SPARC64 - /* - * Not on Ebus, bailing. - */ - return; -#else - /* - * Not on Ebus, must be OBIO. - */ - if (prom_getproperty(up->port_node, "reg", - (char *)®0, sizeof(reg0)) == -1) { - prom_printf("sunsu: no \"reg\" property\n"); - return; - } - prom_apply_obio_ranges(®0, 1); - if (reg0.which_io != 0) { /* Just in case... */ - prom_printf("sunsu: bus number nonzero: 0x%x:%x\n", - reg0.which_io, reg0.phys_addr); - return; - } - up->port.mapbase = reg0.phys_addr; - if ((up->port.membase = ioremap(reg0.phys_addr, reg0.reg_size)) == 0) { - prom_printf("sunsu: Cannot map registers.\n"); - return; - } - - /* - * 0x20 is sun4m thing, Dave Redman heritage. - * See arch/sparc/kernel/irq.c. - */ -#define IRQ_4M(n) ((n)|0x20) - - /* - * There is no intr property on MrCoffee, so hardwire it. - */ - up->port.irq = IRQ_4M(13); -#endif - -ebus_done: - spin_lock_irqsave(&up->port.lock, flags); if (!(up->port.flags & UPF_BUGGY_UART)) { @@ -1265,23 +1176,17 @@ out: static struct uart_driver sunsu_reg = { .owner = THIS_MODULE, .driver_name = "serial", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, }; -static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up, int channel) +static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up) { int quot, baud; #ifdef CONFIG_SERIO struct serio *serio; #endif - spin_lock_init(&up->port.lock); - up->port.line = channel; - up->port.type = PORT_UNKNOWN; - up->port.uartclk = (SU_BASE_BAUD * 16); - if (up->su_type == SU_PORT_KBD) { up->cflag = B1200 | CS8 | CLOCAL | CREAD; baud = 1200; @@ -1293,41 +1198,31 @@ static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up, int channel) sunsu_autoconfig(up); if (up->port.type == PORT_UNKNOWN) - return -1; - - printk(KERN_INFO "su%d at 0x%p (irq = %s) is a %s\n", - channel, - up->port.membase, __irq_itoa(up->port.irq), - sunsu_type(&up->port)); + return -ENODEV; #ifdef CONFIG_SERIO - up->serio = serio = kmalloc(sizeof(struct serio), GFP_KERNEL); - if (serio) { - memset(serio, 0, sizeof(*serio)); - - serio->port_data = up; - - serio->id.type = SERIO_RS232; - if (up->su_type == SU_PORT_KBD) { - serio->id.proto = SERIO_SUNKBD; - strlcpy(serio->name, "sukbd", sizeof(serio->name)); - } else { - serio->id.proto = SERIO_SUN; - serio->id.extra = 1; - strlcpy(serio->name, "sums", sizeof(serio->name)); - } - strlcpy(serio->phys, (channel == 0 ? "su/serio0" : "su/serio1"), - sizeof(serio->phys)); - - serio->write = sunsu_serio_write; - serio->open = sunsu_serio_open; - serio->close = sunsu_serio_close; + serio = &up->serio; + serio->port_data = up; - serio_register_port(serio); + serio->id.type = SERIO_RS232; + if (up->su_type == SU_PORT_KBD) { + serio->id.proto = SERIO_SUNKBD; + strlcpy(serio->name, "sukbd", sizeof(serio->name)); } else { - printk(KERN_WARNING "su%d: not enough memory for serio port\n", - channel); + serio->id.proto = SERIO_SUN; + serio->id.extra = 1; + strlcpy(serio->name, "sums", sizeof(serio->name)); } + strlcpy(serio->phys, + (!(up->port.line & 1) ? "su/serio0" : "su/serio1"), + sizeof(serio->phys)); + + serio->write = sunsu_serio_write; + serio->open = sunsu_serio_open; + serio->close = sunsu_serio_close; + serio->dev.parent = up->port.dev; + + serio_register_port(serio); #endif sunsu_change_speed(&up->port, up->cflag, 0, quot); @@ -1459,22 +1354,20 @@ static struct console sunsu_cons = { * Register console. */ -static inline struct console *SUNSU_CONSOLE(void) +static inline struct console *SUNSU_CONSOLE(int num_uart) { int i; if (con_is_present()) return NULL; - for (i = 0; i < UART_NR; i++) { + for (i = 0; i < num_uart; i++) { int this_minor = sunsu_reg.minor + i; if ((this_minor - 64) == (serial_console - 1)) break; } - if (i == UART_NR) - return NULL; - if (sunsu_ports[i].port_node == 0) + if (i == num_uart) return NULL; sunsu_cons.index = i; @@ -1482,252 +1375,186 @@ static inline struct console *SUNSU_CONSOLE(void) return &sunsu_cons; } #else -#define SUNSU_CONSOLE() (NULL) +#define SUNSU_CONSOLE(num_uart) (NULL) #define sunsu_serial_console_init() do { } while (0) #endif -static int __init sunsu_serial_init(void) +static enum su_type __devinit su_get_type(struct device_node *dp) { - int instance, ret, i; + struct device_node *ap = of_find_node_by_path("/aliases"); - /* How many instances do we need? */ - instance = 0; - for (i = 0; i < UART_NR; i++) { - struct uart_sunsu_port *up = &sunsu_ports[i]; + if (ap) { + char *keyb = of_get_property(ap, "keyboard", NULL); + char *ms = of_get_property(ap, "mouse", NULL); - if (up->su_type == SU_PORT_MS || - up->su_type == SU_PORT_KBD) - continue; + if (keyb) { + if (dp == of_find_node_by_path(keyb)) + return SU_PORT_KBD; + } + if (ms) { + if (dp == of_find_node_by_path(ms)) + return SU_PORT_MS; + } + } - spin_lock_init(&up->port.lock); - up->port.flags |= UPF_BOOT_AUTOCONF; - up->port.type = PORT_UNKNOWN; - up->port.uartclk = (SU_BASE_BAUD * 16); + return SU_PORT_PORT; +} - sunsu_autoconfig(up); - if (up->port.type == PORT_UNKNOWN) - continue; +static int __devinit su_probe(struct of_device *op, const struct of_device_id *match) +{ + static int inst; + struct device_node *dp = op->node; + struct uart_sunsu_port *up; + struct resource *rp; + int err; - up->port.line = instance++; - up->port.ops = &sunsu_pops; - } + if (inst >= UART_NR) + return -EINVAL; - sunsu_reg.minor = sunserial_current_minor; + up = &sunsu_ports[inst]; + up->port.line = inst; - sunsu_reg.nr = instance; + spin_lock_init(&up->port.lock); - ret = uart_register_driver(&sunsu_reg); - if (ret < 0) - return ret; + up->su_type = su_get_type(dp); - sunsu_reg.tty_driver->name_base = sunsu_reg.minor - 64; + rp = &op->resource[0]; + up->port.mapbase = op->resource[0].start; - sunserial_current_minor += instance; + up->reg_size = (rp->end - rp->start) + 1; + up->port.membase = of_ioremap(rp, 0, up->reg_size, "su"); + if (!up->port.membase) + return -ENOMEM; - sunsu_reg.cons = SUNSU_CONSOLE(); + up->port.irq = op->irqs[0]; - for (i = 0; i < UART_NR; i++) { - struct uart_sunsu_port *up = &sunsu_ports[i]; + up->port.dev = &op->dev; - /* Do not register Keyboard/Mouse lines with UART - * layer. - */ - if (up->su_type == SU_PORT_MS || - up->su_type == SU_PORT_KBD) - continue; + up->port.type = PORT_UNKNOWN; + up->port.uartclk = (SU_BASE_BAUD * 16); - if (up->port.type == PORT_UNKNOWN) - continue; + err = 0; + if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) { + err = sunsu_kbd_ms_init(up); + if (err) + goto out_unmap; - uart_add_one_port(&sunsu_reg, &up->port); + return 0; } - return 0; -} + up->port.flags |= UPF_BOOT_AUTOCONF; -static int su_node_ok(int node, char *name, int namelen) -{ - if (strncmp(name, "su", namelen) == 0 || - strncmp(name, "su_pnp", namelen) == 0) - return 1; - - if (strncmp(name, "serial", namelen) == 0) { - char compat[32]; - int clen; - - /* Is it _really_ a 'su' device? */ - clen = prom_getproperty(node, "compatible", compat, sizeof(compat)); - if (clen > 0) { - if (strncmp(compat, "sab82532", 8) == 0) { - /* Nope, Siemens serial, not for us. */ - return 0; - } - } - return 1; - } + sunsu_autoconfig(up); - return 0; -} + err = -ENODEV; + if (up->port.type == PORT_UNKNOWN) + goto out_unmap; -#define SU_PROPSIZE 128 + up->port.ops = &sunsu_pops; -/* - * Scan status structure. - * "prop" is a local variable but it eats stack to keep it in each - * stack frame of a recursive procedure. - */ -struct su_probe_scan { - int msnode, kbnode; /* PROM nodes for mouse and keyboard */ - int msx, kbx; /* minors for mouse and keyboard */ - int devices; /* scan index */ - char prop[SU_PROPSIZE]; -}; + err = uart_add_one_port(&sunsu_reg, &up->port); + if (err) + goto out_unmap; -/* - * We have several platforms which present 'su' in different parts - * of the device tree. 'su' may be found under obio, ebus, isa and pci. - * We walk over the tree and find them wherever PROM hides them. - */ -static void __init su_probe_any(struct su_probe_scan *t, int sunode) -{ - struct uart_sunsu_port *up; - int len; + dev_set_drvdata(&op->dev, up); - if (t->devices >= UART_NR) - return; + inst++; - for (; sunode != 0; sunode = prom_getsibling(sunode)) { - len = prom_getproperty(sunode, "name", t->prop, SU_PROPSIZE); - if (len <= 1) - continue; /* Broken PROM node */ - - if (su_node_ok(sunode, t->prop, len)) { - up = &sunsu_ports[t->devices]; - if (t->kbnode != 0 && sunode == t->kbnode) { - t->kbx = t->devices; - up->su_type = SU_PORT_KBD; - } else if (t->msnode != 0 && sunode == t->msnode) { - t->msx = t->devices; - up->su_type = SU_PORT_MS; - } else { -#ifdef CONFIG_SPARC64 - /* - * Do not attempt to use the truncated - * keyboard/mouse ports as serial ports - * on Ultras with PC keyboard attached. - */ - if (prom_getbool(sunode, "mouse")) - continue; - if (prom_getbool(sunode, "keyboard")) - continue; -#endif - up->su_type = SU_PORT_PORT; - } - up->port_node = sunode; - ++t->devices; - } else { - su_probe_any(t, prom_getchild(sunode)); - } - } + return 0; + +out_unmap: + of_iounmap(up->port.membase, up->reg_size); + return err; } -static int __init sunsu_probe(void) +static int __devexit su_remove(struct of_device *dev) { - int node; - int len; - struct su_probe_scan scan; + struct uart_sunsu_port *up = dev_get_drvdata(&dev->dev);; - /* - * First, we scan the tree. - */ - scan.devices = 0; - scan.msx = -1; - scan.kbx = -1; - scan.kbnode = 0; - scan.msnode = 0; + if (up->su_type == SU_PORT_MS || + up->su_type == SU_PORT_KBD) { +#ifdef CONFIG_SERIO + serio_unregister_port(&up->serio); +#endif + } else if (up->port.type != PORT_UNKNOWN) + uart_remove_one_port(&sunsu_reg, &up->port); - /* - * Get the nodes for keyboard and mouse from 'aliases'... - */ - node = prom_getchild(prom_root_node); - node = prom_searchsiblings(node, "aliases"); - if (node != 0) { - len = prom_getproperty(node, "keyboard", scan.prop, SU_PROPSIZE); - if (len > 0) { - scan.prop[len] = 0; - scan.kbnode = prom_finddevice(scan.prop); - } + return 0; +} - len = prom_getproperty(node, "mouse", scan.prop, SU_PROPSIZE); - if (len > 0) { - scan.prop[len] = 0; - scan.msnode = prom_finddevice(scan.prop); - } - } +static struct of_device_id su_match[] = { + { + .name = "su", + }, + { + .name = "su_pnp", + }, + { + .name = "serial", + .compatible = "su", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, su_match); - su_probe_any(&scan, prom_getchild(prom_root_node)); +static struct of_platform_driver su_driver = { + .name = "su", + .match_table = su_match, + .probe = su_probe, + .remove = __devexit_p(su_remove), +}; - /* - * Second, we process the special case of keyboard and mouse. - * - * Currently if we got keyboard and mouse hooked to "su" ports - * we do not use any possible remaining "su" as a serial port. - * Thus, we ignore values of .msx and .kbx, then compact ports. - */ - if (scan.msx != -1 && scan.kbx != -1) { - sunsu_ports[0].su_type = SU_PORT_MS; - sunsu_ports[0].port_node = scan.msnode; - sunsu_kbd_ms_init(&sunsu_ports[0], 0); +static int num_uart; - sunsu_ports[1].su_type = SU_PORT_KBD; - sunsu_ports[1].port_node = scan.kbnode; - sunsu_kbd_ms_init(&sunsu_ports[1], 1); +static int __init sunsu_init(void) +{ + struct device_node *dp; + int err; - return 0; + num_uart = 0; + for_each_node_by_name(dp, "su") { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; } - - if (scan.msx != -1 || scan.kbx != -1) { - printk("sunsu_probe: cannot match keyboard and mouse, confused\n"); - return -ENODEV; + for_each_node_by_name(dp, "su_pnp") { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } + for_each_node_by_name(dp, "serial") { + if (of_device_is_compatible(dp, "su")) { + if (su_get_type(dp) == SU_PORT_PORT) + num_uart++; + } } - if (scan.devices == 0) - return -ENODEV; + if (num_uart) { + sunsu_reg.minor = sunserial_current_minor; + sunsu_reg.nr = num_uart; + err = uart_register_driver(&sunsu_reg); + if (err) + return err; + sunsu_reg.tty_driver->name_base = sunsu_reg.minor - 64; + sunserial_current_minor += num_uart; + sunsu_reg.cons = SUNSU_CONSOLE(num_uart); + } - /* - * Console must be initiated after the generic initialization. - */ - sunsu_serial_init(); + err = of_register_driver(&su_driver, &of_bus_type); + if (err && num_uart) + uart_unregister_driver(&sunsu_reg); - return 0; + return err; } static void __exit sunsu_exit(void) { - int i, saw_uart; - - saw_uart = 0; - for (i = 0; i < UART_NR; i++) { - struct uart_sunsu_port *up = &sunsu_ports[i]; - - if (up->su_type == SU_PORT_MS || - up->su_type == SU_PORT_KBD) { -#ifdef CONFIG_SERIO - if (up->serio) { - serio_unregister_port(up->serio); - up->serio = NULL; - } -#endif - } else if (up->port.type != PORT_UNKNOWN) { - uart_remove_one_port(&sunsu_reg, &up->port); - saw_uart++; - } - } - - if (saw_uart) + if (num_uart) uart_unregister_driver(&sunsu_reg); } -module_init(sunsu_probe); +module_init(sunsu_init); module_exit(sunsu_exit); + +MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller"); +MODULE_DESCRIPTION("Sun SU serial port driver"); +MODULE_VERSION("2.0"); MODULE_LICENSE("GPL"); diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c index cd49ebbf4a45..a1456d9352cb 100644 --- a/drivers/serial/sunzilog.c +++ b/drivers/serial/sunzilog.c @@ -1,5 +1,4 @@ -/* - * sunzilog.c +/* sunzilog.c: Zilog serial driver for Sparc systems. * * Driver for Zilog serial chips found on Sun workstations and * servers. This driver could actually be made more generic. @@ -10,10 +9,9 @@ * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their * work there. * - * Copyright (C) 2002 David S. Miller (davem@redhat.com) + * Copyright (C) 2002, 2006 David S. Miller (davem@davemloft.net) */ -#include <linux/config.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/sched.h> @@ -38,10 +36,8 @@ #include <asm/io.h> #include <asm/irq.h> -#ifdef CONFIG_SPARC64 -#include <asm/fhc.h> -#endif -#include <asm/sbus.h> +#include <asm/prom.h> +#include <asm/of_device.h> #if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -65,7 +61,7 @@ #define ZSDELAY() #define ZSDELAY_LONG() #define ZS_WSYNC(__channel) \ - sbus_readb(&((__channel)->control)) + readb(&((__channel)->control)) #endif static int num_sunzilog; @@ -107,7 +103,7 @@ struct uart_sunzilog_port { unsigned char prev_status; #ifdef CONFIG_SERIO - struct serio *serio; + struct serio serio; int serio_open; #endif }; @@ -138,9 +134,9 @@ static unsigned char read_zsreg(struct zilog_channel __iomem *channel, { unsigned char retval; - sbus_writeb(reg, &channel->control); + writeb(reg, &channel->control); ZSDELAY(); - retval = sbus_readb(&channel->control); + retval = readb(&channel->control); ZSDELAY(); return retval; @@ -149,9 +145,9 @@ static unsigned char read_zsreg(struct zilog_channel __iomem *channel, static void write_zsreg(struct zilog_channel __iomem *channel, unsigned char reg, unsigned char value) { - sbus_writeb(reg, &channel->control); + writeb(reg, &channel->control); ZSDELAY(); - sbus_writeb(value, &channel->control); + writeb(value, &channel->control); ZSDELAY(); } @@ -162,17 +158,17 @@ static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel) for (i = 0; i < 32; i++) { unsigned char regval; - regval = sbus_readb(&channel->control); + regval = readb(&channel->control); ZSDELAY(); if (regval & Rx_CH_AV) break; regval = read_zsreg(channel, R1); - sbus_readb(&channel->data); + readb(&channel->data); ZSDELAY(); if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) { - sbus_writeb(ERR_RES, &channel->control); + writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } @@ -194,7 +190,7 @@ static void __load_zsregs(struct zilog_channel __iomem *channel, unsigned char * udelay(100); } - sbus_writeb(ERR_RES, &channel->control); + writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); @@ -291,7 +287,7 @@ static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up, /* Stop-A is handled by drivers/char/keyboard.c now. */ #ifdef CONFIG_SERIO if (up->serio_open) - serio_interrupt(up->serio, ch, 0, regs); + serio_interrupt(&up->serio, ch, 0, regs); #endif } else if (ZS_IS_MOUSE(up)) { int ret = suncore_mouse_baud_detection(ch, is_break); @@ -306,7 +302,7 @@ static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up, case 0: #ifdef CONFIG_SERIO if (up->serio_open) - serio_interrupt(up->serio, ch, 0, regs); + serio_interrupt(&up->serio, ch, 0, regs); #endif break; }; @@ -330,12 +326,12 @@ sunzilog_receive_chars(struct uart_sunzilog_port *up, r1 = read_zsreg(channel, R1); if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { - sbus_writeb(ERR_RES, &channel->control); + writeb(ERR_RES, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } - ch = sbus_readb(&channel->control); + ch = readb(&channel->control); ZSDELAY(); /* This funny hack depends upon BRK_ABRT not interfering @@ -347,7 +343,7 @@ sunzilog_receive_chars(struct uart_sunzilog_port *up, if (!(ch & Rx_CH_AV)) break; - ch = sbus_readb(&channel->data); + ch = readb(&channel->data); ZSDELAY(); ch &= up->parity_mask; @@ -406,10 +402,10 @@ static void sunzilog_status_handle(struct uart_sunzilog_port *up, { unsigned char status; - status = sbus_readb(&channel->control); + status = readb(&channel->control); ZSDELAY(); - sbus_writeb(RES_EXT_INT, &channel->control); + writeb(RES_EXT_INT, &channel->control); ZSDELAY(); ZS_WSYNC(channel); @@ -421,7 +417,7 @@ static void sunzilog_status_handle(struct uart_sunzilog_port *up, * confusing the PROM. */ while (1) { - status = sbus_readb(&channel->control); + status = readb(&channel->control); ZSDELAY(); if (!(status & BRK_ABRT)) break; @@ -458,7 +454,7 @@ static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, struct circ_buf *xmit; if (ZS_IS_CONS(up)) { - unsigned char status = sbus_readb(&channel->control); + unsigned char status = readb(&channel->control); ZSDELAY(); /* TX still busy? Just wait for the next TX done interrupt. @@ -487,7 +483,7 @@ static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, if (up->port.x_char) { up->flags |= SUNZILOG_FLAG_TX_ACTIVE; - sbus_writeb(up->port.x_char, &channel->data); + writeb(up->port.x_char, &channel->data); ZSDELAY(); ZS_WSYNC(channel); @@ -506,7 +502,7 @@ static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, goto ack_tx_int; up->flags |= SUNZILOG_FLAG_TX_ACTIVE; - sbus_writeb(xmit->buf[xmit->tail], &channel->data); + writeb(xmit->buf[xmit->tail], &channel->data); ZSDELAY(); ZS_WSYNC(channel); @@ -519,7 +515,7 @@ static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, return; ack_tx_int: - sbus_writeb(RES_Tx_P, &channel->control); + writeb(RES_Tx_P, &channel->control); ZSDELAY(); ZS_WSYNC(channel); } @@ -540,7 +536,7 @@ static irqreturn_t sunzilog_interrupt(int irq, void *dev_id, struct pt_regs *reg /* Channel A */ tty = NULL; if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { - sbus_writeb(RES_H_IUS, &channel->control); + writeb(RES_H_IUS, &channel->control); ZSDELAY(); ZS_WSYNC(channel); @@ -563,7 +559,7 @@ static irqreturn_t sunzilog_interrupt(int irq, void *dev_id, struct pt_regs *reg spin_lock(&up->port.lock); tty = NULL; if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { - sbus_writeb(RES_H_IUS, &channel->control); + writeb(RES_H_IUS, &channel->control); ZSDELAY(); ZS_WSYNC(channel); @@ -594,7 +590,7 @@ static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *p unsigned char status; channel = ZILOG_CHANNEL_FROM_PORT(port); - status = sbus_readb(&channel->control); + status = readb(&channel->control); ZSDELAY(); return status; @@ -682,7 +678,7 @@ static void sunzilog_start_tx(struct uart_port *port) up->flags |= SUNZILOG_FLAG_TX_ACTIVE; up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; - status = sbus_readb(&channel->control); + status = readb(&channel->control); ZSDELAY(); /* TX busy? Just wait for the TX done interrupt. */ @@ -693,7 +689,7 @@ static void sunzilog_start_tx(struct uart_port *port) * IRQ sending engine. */ if (port->x_char) { - sbus_writeb(port->x_char, &channel->data); + writeb(port->x_char, &channel->data); ZSDELAY(); ZS_WSYNC(channel); @@ -702,7 +698,7 @@ static void sunzilog_start_tx(struct uart_port *port) } else { struct circ_buf *xmit = &port->info->xmit; - sbus_writeb(xmit->buf[xmit->tail], &channel->data); + writeb(xmit->buf[xmit->tail], &channel->data); ZSDELAY(); ZS_WSYNC(channel); @@ -779,7 +775,7 @@ static void __sunzilog_startup(struct uart_sunzilog_port *up) struct zilog_channel __iomem *channel; channel = ZILOG_CHANNEL_FROM_PORT(&up->port); - up->prev_status = sbus_readb(&channel->control); + up->prev_status = readb(&channel->control); /* Enable receiver and transmitter. */ up->curregs[R3] |= RxENAB; @@ -963,7 +959,7 @@ sunzilog_set_termios(struct uart_port *port, struct termios *termios, static const char *sunzilog_type(struct uart_port *port) { - return "SunZilog"; + return "zs"; } /* We do not request/release mappings of the registers here, this @@ -1012,242 +1008,55 @@ static struct uart_sunzilog_port *sunzilog_port_table; static struct zilog_layout __iomem **sunzilog_chip_regs; static struct uart_sunzilog_port *sunzilog_irq_chain; -static int zilog_irq = -1; static struct uart_driver sunzilog_reg = { .owner = THIS_MODULE, .driver_name = "ttyS", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, }; -static void * __init alloc_one_table(unsigned long size) -{ - void *ret; - - ret = kmalloc(size, GFP_KERNEL); - if (ret != NULL) - memset(ret, 0, size); - - return ret; -} - -static void __init sunzilog_alloc_tables(void) -{ - sunzilog_port_table = - alloc_one_table(NUM_CHANNELS * sizeof(struct uart_sunzilog_port)); - sunzilog_chip_regs = - alloc_one_table(NUM_SUNZILOG * sizeof(struct zilog_layout __iomem *)); - - if (sunzilog_port_table == NULL || sunzilog_chip_regs == NULL) { - prom_printf("SunZilog: Cannot allocate tables.\n"); - prom_halt(); - } -} - -#ifdef CONFIG_SPARC64 - -/* We used to attempt to use the address property of the Zilog device node - * but that totally is not necessary on sparc64. - */ -static struct zilog_layout __iomem * __init get_zs_sun4u(int chip, int zsnode) +static int __init sunzilog_alloc_tables(void) { - void __iomem *mapped_addr; - unsigned int sun4u_ino; - struct sbus_bus *sbus = NULL; - struct sbus_dev *sdev = NULL; - int err; - - if (central_bus == NULL) { - for_each_sbus(sbus) { - for_each_sbusdev(sdev, sbus) { - if (sdev->prom_node == zsnode) - goto found; - } - } - } - found: - if (sdev == NULL && central_bus == NULL) { - prom_printf("SunZilog: sdev&¢ral == NULL for " - "Zilog %d in get_zs_sun4u.\n", chip); - prom_halt(); - } - if (central_bus == NULL) { - mapped_addr = - sbus_ioremap(&sdev->resource[0], 0, - PAGE_SIZE, - "Zilog Registers"); - } else { - struct linux_prom_registers zsregs[1]; - - err = prom_getproperty(zsnode, "reg", - (char *) &zsregs[0], - sizeof(zsregs)); - if (err == -1) { - prom_printf("SunZilog: Cannot map " - "Zilog %d regs on " - "central bus.\n", chip); - prom_halt(); - } - apply_fhc_ranges(central_bus->child, - &zsregs[0], 1); - apply_central_ranges(central_bus, &zsregs[0], 1); - mapped_addr = (void __iomem *) - ((((u64)zsregs[0].which_io)<<32UL) | - ((u64)zsregs[0].phys_addr)); - } - - if (zilog_irq == -1) { - if (central_bus) { - unsigned long iclr, imap; - - iclr = central_bus->child->fhc_regs.uregs - + FHC_UREGS_ICLR; - imap = central_bus->child->fhc_regs.uregs - + FHC_UREGS_IMAP; - zilog_irq = build_irq(12, 0, iclr, imap); - } else { - err = prom_getproperty(zsnode, "interrupts", - (char *) &sun4u_ino, - sizeof(sun4u_ino)); - zilog_irq = sbus_build_irq(sbus_root, sun4u_ino); - } - } - - return (struct zilog_layout __iomem *) mapped_addr; -} -#else /* CONFIG_SPARC64 */ - -/* - * XXX The sun4d case is utterly screwed: it tries to re-walk the tree - * (for the 3rd time) in order to find bootbus and cpu. Streamline it. - */ -static struct zilog_layout __iomem * __init get_zs_sun4cmd(int chip, int node) -{ - struct linux_prom_irqs irq_info[2]; - void __iomem *mapped_addr = NULL; - int zsnode, cpunode, bbnode; - struct linux_prom_registers zsreg[4]; - struct resource res; - - if (sparc_cpu_model == sun4d) { - int walk; - - zsnode = 0; - bbnode = 0; - cpunode = 0; - for (walk = prom_getchild(prom_root_node); - (walk = prom_searchsiblings(walk, "cpu-unit")) != 0; - walk = prom_getsibling(walk)) { - bbnode = prom_getchild(walk); - if (bbnode && - (bbnode = prom_searchsiblings(bbnode, "bootbus"))) { - if ((zsnode = prom_getchild(bbnode)) == node) { - cpunode = walk; - break; - } - } - } - if (!walk) { - prom_printf("SunZilog: Cannot find the %d'th bootbus on sun4d.\n", - (chip / 2)); - prom_halt(); - } + struct uart_sunzilog_port *up; + unsigned long size; + int i; - if (prom_getproperty(zsnode, "reg", - (char *) zsreg, sizeof(zsreg)) == -1) { - prom_printf("SunZilog: Cannot map Zilog %d\n", chip); - prom_halt(); - } - /* XXX Looks like an off by one? */ - prom_apply_generic_ranges(bbnode, cpunode, zsreg, 1); - res.start = zsreg[0].phys_addr; - res.end = res.start + (8 - 1); - res.flags = zsreg[0].which_io | IORESOURCE_IO; - mapped_addr = sbus_ioremap(&res, 0, 8, "Zilog Serial"); + size = NUM_CHANNELS * sizeof(struct uart_sunzilog_port); + sunzilog_port_table = kzalloc(size, GFP_KERNEL); + if (!sunzilog_port_table) + return -ENOMEM; - } else { - zsnode = node; + for (i = 0; i < NUM_CHANNELS; i++) { + up = &sunzilog_port_table[i]; -#if 0 /* XXX When was this used? */ - if (prom_getintdefault(zsnode, "slave", -1) != chipid) { - zsnode = prom_getsibling(zsnode); - continue; - } -#endif + spin_lock_init(&up->port.lock); - /* - * "address" is only present on ports that OBP opened - * (from Mitch Bradley's "Hitchhiker's Guide to OBP"). - * We do not use it. - */ + if (i == 0) + sunzilog_irq_chain = up; - if (prom_getproperty(zsnode, "reg", - (char *) zsreg, sizeof(zsreg)) == -1) { - prom_printf("SunZilog: Cannot map Zilog %d\n", chip); - prom_halt(); - } - if (sparc_cpu_model == sun4m) /* Crude. Pass parent. XXX */ - prom_apply_obio_ranges(zsreg, 1); - res.start = zsreg[0].phys_addr; - res.end = res.start + (8 - 1); - res.flags = zsreg[0].which_io | IORESOURCE_IO; - mapped_addr = sbus_ioremap(&res, 0, 8, "Zilog Serial"); + if (i < NUM_CHANNELS - 1) + up->next = up + 1; + else + up->next = NULL; } - if (prom_getproperty(zsnode, "intr", - (char *) irq_info, sizeof(irq_info)) - % sizeof(struct linux_prom_irqs)) { - prom_printf("SunZilog: Cannot get IRQ property for Zilog %d.\n", - chip); - prom_halt(); - } - if (zilog_irq == -1) { - zilog_irq = irq_info[0].pri; - } else if (zilog_irq != irq_info[0].pri) { - /* XXX. Dumb. Should handle per-chip IRQ, for add-ons. */ - prom_printf("SunZilog: Inconsistent IRQ layout for Zilog %d.\n", - chip); - prom_halt(); + size = NUM_SUNZILOG * sizeof(struct zilog_layout __iomem *); + sunzilog_chip_regs = kzalloc(size, GFP_KERNEL); + if (!sunzilog_chip_regs) { + kfree(sunzilog_port_table); + sunzilog_irq_chain = NULL; + return -ENOMEM; } - return (struct zilog_layout __iomem *) mapped_addr; + return 0; } -#endif /* !(CONFIG_SPARC64) */ -/* Get the address of the registers for SunZilog instance CHIP. */ -static struct zilog_layout __iomem * __init get_zs(int chip, int node) +static void sunzilog_free_tables(void) { - if (chip < 0 || chip >= NUM_SUNZILOG) { - prom_printf("SunZilog: Illegal chip number %d in get_zs.\n", chip); - prom_halt(); - } - -#ifdef CONFIG_SPARC64 - return get_zs_sun4u(chip, node); -#else - - if (sparc_cpu_model == sun4) { - struct resource res; - - /* Not probe-able, hard code it. */ - switch (chip) { - case 0: - res.start = 0xf1000000; - break; - case 1: - res.start = 0xf0000000; - break; - }; - zilog_irq = 12; - res.end = (res.start + (8 - 1)); - res.flags = IORESOURCE_IO; - return sbus_ioremap(&res, 0, 8, "SunZilog"); - } - - return get_zs_sun4cmd(chip, node); -#endif + kfree(sunzilog_port_table); + sunzilog_irq_chain = NULL; + kfree(sunzilog_chip_regs); } #define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */ @@ -1261,7 +1070,7 @@ static void sunzilog_putchar(struct uart_port *port, int ch) * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM */ do { - unsigned char val = sbus_readb(&channel->control); + unsigned char val = readb(&channel->control); if (val & Tx_BUF_EMP) { ZSDELAY(); break; @@ -1269,7 +1078,7 @@ static void sunzilog_putchar(struct uart_port *port, int ch) udelay(5); } while (--loops); - sbus_writeb(ch, &channel->data); + writeb(ch, &channel->data); ZSDELAY(); ZS_WSYNC(channel); } @@ -1386,28 +1195,6 @@ static struct console sunzilog_console = { .data = &sunzilog_reg, }; -static int __init sunzilog_console_init(void) -{ - int i; - - if (con_is_present()) - return 0; - - for (i = 0; i < NUM_CHANNELS; i++) { - int this_minor = sunzilog_reg.minor + i; - - if ((this_minor - 64) == (serial_console - 1)) - break; - } - if (i == NUM_CHANNELS) - return 0; - - sunzilog_console.index = i; - sunzilog_port_table[i].flags |= SUNZILOG_FLAG_IS_CONS; - register_console(&sunzilog_console); - return 0; -} - static inline struct console *SUNZILOG_CONSOLE(void) { int i; @@ -1432,101 +1219,8 @@ static inline struct console *SUNZILOG_CONSOLE(void) #else #define SUNZILOG_CONSOLE() (NULL) -#define sunzilog_console_init() do { } while (0) #endif -/* - * We scan the PROM tree recursively. This is the most reliable way - * to find Zilog nodes on various platforms. However, we face an extreme - * shortage of kernel stack, so we must be very careful. To that end, - * we scan only to a certain depth, and we use a common property buffer - * in the scan structure. - */ -#define ZS_PROPSIZE 128 -#define ZS_SCAN_DEPTH 5 - -struct zs_probe_scan { - int depth; - void (*scanner)(struct zs_probe_scan *t, int node); - - int devices; - char prop[ZS_PROPSIZE]; -}; - -static int __inline__ sunzilog_node_ok(int node, const char *name, int len) -{ - if (strncmp(name, "zs", len) == 0) - return 1; - /* Don't fold this procedure just yet. Compare to su_node_ok(). */ - return 0; -} - -static void __init sunzilog_scan(struct zs_probe_scan *t, int node) -{ - int len; - - for (; node != 0; node = prom_getsibling(node)) { - len = prom_getproperty(node, "name", t->prop, ZS_PROPSIZE); - if (len <= 1) - continue; /* Broken PROM node */ - if (sunzilog_node_ok(node, t->prop, len)) { - (*t->scanner)(t, node); - } else { - if (t->depth < ZS_SCAN_DEPTH) { - t->depth++; - sunzilog_scan(t, prom_getchild(node)); - --t->depth; - } - } - } -} - -static void __init sunzilog_prepare(void) -{ - struct uart_sunzilog_port *up; - struct zilog_layout __iomem *rp; - int channel, chip; - - /* - * Temporary fix. - */ - for (channel = 0; channel < NUM_CHANNELS; channel++) - spin_lock_init(&sunzilog_port_table[channel].port.lock); - - sunzilog_irq_chain = up = &sunzilog_port_table[0]; - for (channel = 0; channel < NUM_CHANNELS - 1; channel++) - up[channel].next = &up[channel + 1]; - up[channel].next = NULL; - - for (chip = 0; chip < NUM_SUNZILOG; chip++) { - rp = sunzilog_chip_regs[chip]; - up[(chip * 2) + 0].port.membase = (void __iomem *)&rp->channelA; - up[(chip * 2) + 1].port.membase = (void __iomem *)&rp->channelB; - - /* Channel A */ - up[(chip * 2) + 0].port.iotype = UPIO_MEM; - up[(chip * 2) + 0].port.irq = zilog_irq; - up[(chip * 2) + 0].port.uartclk = ZS_CLOCK; - up[(chip * 2) + 0].port.fifosize = 1; - up[(chip * 2) + 0].port.ops = &sunzilog_pops; - up[(chip * 2) + 0].port.type = PORT_SUNZILOG; - up[(chip * 2) + 0].port.flags = 0; - up[(chip * 2) + 0].port.line = (chip * 2) + 0; - up[(chip * 2) + 0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A; - - /* Channel B */ - up[(chip * 2) + 1].port.iotype = UPIO_MEM; - up[(chip * 2) + 1].port.irq = zilog_irq; - up[(chip * 2) + 1].port.uartclk = ZS_CLOCK; - up[(chip * 2) + 1].port.fifosize = 1; - up[(chip * 2) + 1].port.ops = &sunzilog_pops; - up[(chip * 2) + 1].port.type = PORT_SUNZILOG; - up[(chip * 2) + 1].port.flags = 0; - up[(chip * 2) + 1].port.line = (chip * 2) + 1; - up[(chip * 2) + 1].flags |= 0; - } -} - static void __init sunzilog_init_kbdms(struct uart_sunzilog_port *up, int channel) { int baud, brg; @@ -1540,8 +1234,6 @@ static void __init sunzilog_init_kbdms(struct uart_sunzilog_port *up, int channe up->cflag = B4800 | CS8 | CLOCAL | CREAD; baud = 4800; } - printk(KERN_INFO "zs%d at 0x%p (irq = %s) is a SunZilog\n", - channel, up->port.membase, __irq_itoa(zilog_irq)); up->curregs[R15] = BRKIE; brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); @@ -1553,216 +1245,268 @@ static void __init sunzilog_init_kbdms(struct uart_sunzilog_port *up, int channe #ifdef CONFIG_SERIO static void __init sunzilog_register_serio(struct uart_sunzilog_port *up, int channel) { - struct serio *serio; - - up->serio = serio = kmalloc(sizeof(struct serio), GFP_KERNEL); - if (serio) { - memset(serio, 0, sizeof(*serio)); - - serio->port_data = up; - - serio->id.type = SERIO_RS232; - if (channel == KEYBOARD_LINE) { - serio->id.proto = SERIO_SUNKBD; - strlcpy(serio->name, "zskbd", sizeof(serio->name)); - } else { - serio->id.proto = SERIO_SUN; - serio->id.extra = 1; - strlcpy(serio->name, "zsms", sizeof(serio->name)); - } - strlcpy(serio->phys, - (channel == KEYBOARD_LINE ? "zs/serio0" : "zs/serio1"), - sizeof(serio->phys)); + struct serio *serio = &up->serio; - serio->write = sunzilog_serio_write; - serio->open = sunzilog_serio_open; - serio->close = sunzilog_serio_close; + serio->port_data = up; - serio_register_port(serio); + serio->id.type = SERIO_RS232; + if (channel == KEYBOARD_LINE) { + serio->id.proto = SERIO_SUNKBD; + strlcpy(serio->name, "zskbd", sizeof(serio->name)); } else { - printk(KERN_WARNING "zs%d: not enough memory for serio port\n", - channel); + serio->id.proto = SERIO_SUN; + serio->id.extra = 1; + strlcpy(serio->name, "zsms", sizeof(serio->name)); } + strlcpy(serio->phys, + (channel == KEYBOARD_LINE ? "zs/serio0" : "zs/serio1"), + sizeof(serio->phys)); + + serio->write = sunzilog_serio_write; + serio->open = sunzilog_serio_open; + serio->close = sunzilog_serio_close; + serio->dev.parent = up->port.dev; + + serio_register_port(serio); } #endif -static void __init sunzilog_init_hw(void) +static void __init sunzilog_init_hw(struct uart_sunzilog_port *up) { - int i; - - for (i = 0; i < NUM_CHANNELS; i++) { - struct uart_sunzilog_port *up = &sunzilog_port_table[i]; - struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(&up->port); - unsigned long flags; - int baud, brg; + struct zilog_channel __iomem *channel; + unsigned long flags; + int baud, brg; - spin_lock_irqsave(&up->port.lock, flags); + channel = ZILOG_CHANNEL_FROM_PORT(&up->port); - if (ZS_IS_CHANNEL_A(up)) { - write_zsreg(channel, R9, FHWRES); - ZSDELAY_LONG(); - (void) read_zsreg(channel, R0); - } + spin_lock_irqsave(&up->port.lock, flags); + if (ZS_IS_CHANNEL_A(up)) { + write_zsreg(channel, R9, FHWRES); + ZSDELAY_LONG(); + (void) read_zsreg(channel, R0); + } - if (i == KEYBOARD_LINE || i == MOUSE_LINE) { - sunzilog_init_kbdms(up, i); - up->curregs[R9] |= (NV | MIE); - write_zsreg(channel, R9, up->curregs[R9]); - } else { - /* Normal serial TTY. */ - up->parity_mask = 0xff; - up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; - up->curregs[R4] = PAR_EVEN | X16CLK | SB1; - up->curregs[R3] = RxENAB | Rx8; - up->curregs[R5] = TxENAB | Tx8; - up->curregs[R9] = NV | MIE; - up->curregs[R10] = NRZ; - up->curregs[R11] = TCBR | RCBR; - baud = 9600; - brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); - up->curregs[R12] = (brg & 0xff); - up->curregs[R13] = (brg >> 8) & 0xff; - up->curregs[R14] = BRSRC | BRENAB; - __load_zsregs(channel, up->curregs); - write_zsreg(channel, R9, up->curregs[R9]); - } + if (up->port.line == KEYBOARD_LINE || + up->port.line == MOUSE_LINE) { + sunzilog_init_kbdms(up, up->port.line); + up->curregs[R9] |= (NV | MIE); + write_zsreg(channel, R9, up->curregs[R9]); + } else { + /* Normal serial TTY. */ + up->parity_mask = 0xff; + up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; + up->curregs[R4] = PAR_EVEN | X16CLK | SB1; + up->curregs[R3] = RxENAB | Rx8; + up->curregs[R5] = TxENAB | Tx8; + up->curregs[R9] = NV | MIE; + up->curregs[R10] = NRZ; + up->curregs[R11] = TCBR | RCBR; + baud = 9600; + brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); + up->curregs[R12] = (brg & 0xff); + up->curregs[R13] = (brg >> 8) & 0xff; + up->curregs[R14] = BRSRC | BRENAB; + __load_zsregs(channel, up->curregs); + write_zsreg(channel, R9, up->curregs[R9]); + } - spin_unlock_irqrestore(&up->port.lock, flags); + spin_unlock_irqrestore(&up->port.lock, flags); #ifdef CONFIG_SERIO - if (i == KEYBOARD_LINE || i == MOUSE_LINE) - sunzilog_register_serio(up, i); + if (up->port.line == KEYBOARD_LINE || up->port.line == MOUSE_LINE) + sunzilog_register_serio(up, up->port.line); #endif - } -} - -static struct zilog_layout __iomem * __init get_zs(int chip, int node); - -static void __init sunzilog_scan_probe(struct zs_probe_scan *t, int node) -{ - sunzilog_chip_regs[t->devices] = get_zs(t->devices, node); - t->devices++; } -static int __init sunzilog_ports_init(void) +static int __devinit zs_get_instance(struct device_node *dp) { - struct zs_probe_scan scan; int ret; - int uart_count; - int i; - - printk(KERN_DEBUG "SunZilog: %d chips.\n", NUM_SUNZILOG); - - scan.scanner = sunzilog_scan_probe; - scan.depth = 0; - scan.devices = 0; - sunzilog_scan(&scan, prom_getchild(prom_root_node)); - - sunzilog_prepare(); - if (request_irq(zilog_irq, sunzilog_interrupt, SA_SHIRQ, - "SunZilog", sunzilog_irq_chain)) { - prom_printf("SunZilog: Unable to register zs interrupt handler.\n"); - prom_halt(); - } + ret = of_getintprop_default(dp, "slave", -1); + if (ret != -1) + return ret; - sunzilog_init_hw(); + if (of_find_property(dp, "keyboard", NULL)) + ret = 1; + else + ret = 0; - /* We can only init this once we have probed the Zilogs - * in the system. Do not count channels assigned to keyboards - * or mice when we are deciding how many ports to register. - */ - uart_count = 0; - for (i = 0; i < NUM_CHANNELS; i++) { - struct uart_sunzilog_port *up = &sunzilog_port_table[i]; + return ret; +} - if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) - continue; +static int zilog_irq = -1; - uart_count++; - } - - sunzilog_reg.nr = uart_count; - sunzilog_reg.minor = sunserial_current_minor; +static int __devinit zs_probe(struct of_device *dev, const struct of_device_id *match) +{ + struct of_device *op = to_of_device(&dev->dev); + struct uart_sunzilog_port *up; + struct zilog_layout __iomem *rp; + int inst = zs_get_instance(dev->node); + int err; - ret = uart_register_driver(&sunzilog_reg); - if (ret == 0) { - sunzilog_reg.tty_driver->name_base = sunzilog_reg.minor - 64; - sunzilog_reg.cons = SUNZILOG_CONSOLE(); + sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0, + sizeof(struct zilog_layout), + "zs"); + if (!sunzilog_chip_regs[inst]) + return -ENOMEM; - sunserial_current_minor += uart_count; + rp = sunzilog_chip_regs[inst]; - for (i = 0; i < NUM_CHANNELS; i++) { - struct uart_sunzilog_port *up = &sunzilog_port_table[i]; + if (zilog_irq == -1) { + zilog_irq = op->irqs[0]; + err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED, + "zs", sunzilog_irq_chain); + if (err) { + of_iounmap(rp, sizeof(struct zilog_layout)); - if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) - continue; + return err; + } + } - if (uart_add_one_port(&sunzilog_reg, &up->port)) { - printk(KERN_ERR - "SunZilog: failed to add port zs%d\n", i); - } + up = &sunzilog_port_table[inst * 2]; + + /* Channel A */ + up[0].port.mapbase = op->resource[0].start + 0x00; + up[0].port.membase = (void __iomem *) &rp->channelA; + up[0].port.iotype = UPIO_MEM; + up[0].port.irq = op->irqs[0]; + up[0].port.uartclk = ZS_CLOCK; + up[0].port.fifosize = 1; + up[0].port.ops = &sunzilog_pops; + up[0].port.type = PORT_SUNZILOG; + up[0].port.flags = 0; + up[0].port.line = (inst * 2) + 0; + up[0].port.dev = &op->dev; + up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A; + if (inst == 1) + up[0].flags |= SUNZILOG_FLAG_CONS_KEYB; + sunzilog_init_hw(&up[0]); + + /* Channel B */ + up[1].port.mapbase = op->resource[0].start + 0x04; + up[1].port.membase = (void __iomem *) &rp->channelB; + up[1].port.iotype = UPIO_MEM; + up[1].port.irq = op->irqs[0]; + up[1].port.uartclk = ZS_CLOCK; + up[1].port.fifosize = 1; + up[1].port.ops = &sunzilog_pops; + up[1].port.type = PORT_SUNZILOG; + up[1].port.flags = 0; + up[1].port.line = (inst * 2) + 1; + up[1].port.dev = &op->dev; + up[1].flags |= 0; + if (inst == 1) + up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE; + sunzilog_init_hw(&up[1]); + + if (inst != 1) { + err = uart_add_one_port(&sunzilog_reg, &up[0].port); + if (err) { + of_iounmap(rp, sizeof(struct zilog_layout)); + return err; + } + err = uart_add_one_port(&sunzilog_reg, &up[1].port); + if (err) { + uart_remove_one_port(&sunzilog_reg, &up[0].port); + of_iounmap(rp, sizeof(struct zilog_layout)); + return err; } } - return ret; + dev_set_drvdata(&dev->dev, &up[0]); + + return 0; } -static void __init sunzilog_scan_count(struct zs_probe_scan *t, int node) +static void __devexit zs_remove_one(struct uart_sunzilog_port *up) { - t->devices++; + if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) { +#ifdef CONFIG_SERIO + serio_unregister_port(&up->serio); +#endif + } else + uart_remove_one_port(&sunzilog_reg, &up->port); } -static int __init sunzilog_ports_count(void) +static int __devexit zs_remove(struct of_device *dev) { - struct zs_probe_scan scan; + struct uart_sunzilog_port *up = dev_get_drvdata(&dev->dev); + struct zilog_layout __iomem *regs; - /* Sun4 Zilog setup is hard coded, no probing to do. */ - if (sparc_cpu_model == sun4) - return 2; + zs_remove_one(&up[0]); + zs_remove_one(&up[1]); - scan.scanner = sunzilog_scan_count; - scan.depth = 0; - scan.devices = 0; + regs = sunzilog_chip_regs[up[0].port.line / 2]; + of_iounmap(regs, sizeof(struct zilog_layout)); - sunzilog_scan(&scan, prom_getchild(prom_root_node)); + dev_set_drvdata(&dev->dev, NULL); - return scan.devices; + return 0; } +static struct of_device_id zs_match[] = { + { + .name = "zs", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, zs_match); + +static struct of_platform_driver zs_driver = { + .name = "zs", + .match_table = zs_match, + .probe = zs_probe, + .remove = __devexit_p(zs_remove), +}; + static int __init sunzilog_init(void) { + struct device_node *dp; + int err; - NUM_SUNZILOG = sunzilog_ports_count(); - if (NUM_SUNZILOG == 0) - return -ENODEV; + NUM_SUNZILOG = 0; + for_each_node_by_name(dp, "zs") + NUM_SUNZILOG++; - sunzilog_alloc_tables(); + if (NUM_SUNZILOG) { + int uart_count; - sunzilog_ports_init(); + err = sunzilog_alloc_tables(); + if (err) + return err; - return 0; + /* Subtract 1 for keyboard, 1 for mouse. */ + uart_count = (NUM_SUNZILOG * 2) - 2; + + sunzilog_reg.nr = uart_count; + sunzilog_reg.minor = sunserial_current_minor; + err = uart_register_driver(&sunzilog_reg); + if (err) { + sunzilog_free_tables(); + return err; + } + sunzilog_reg.tty_driver->name_base = sunzilog_reg.minor - 64; + sunzilog_reg.cons = SUNZILOG_CONSOLE(); + + sunserial_current_minor += uart_count; + } + + return of_register_driver(&zs_driver, &of_bus_type); } static void __exit sunzilog_exit(void) { - int i; + of_unregister_driver(&zs_driver); - for (i = 0; i < NUM_CHANNELS; i++) { - struct uart_sunzilog_port *up = &sunzilog_port_table[i]; - - if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) { -#ifdef CONFIG_SERIO - if (up->serio) { - serio_unregister_port(up->serio); - up->serio = NULL; - } -#endif - } else - uart_remove_one_port(&sunzilog_reg, &up->port); + if (zilog_irq != -1) { + free_irq(zilog_irq, sunzilog_irq_chain); + zilog_irq = -1; } - uart_unregister_driver(&sunzilog_reg); + if (NUM_SUNZILOG) { + uart_unregister_driver(&sunzilog_reg); + sunzilog_free_tables(); + } } module_init(sunzilog_init); @@ -1770,4 +1514,5 @@ module_exit(sunzilog_exit); MODULE_AUTHOR("David S. Miller"); MODULE_DESCRIPTION("Sun Zilog serial port driver"); +MODULE_VERSION("2.0"); MODULE_LICENSE("GPL"); diff --git a/drivers/serial/v850e_uart.c b/drivers/serial/v850e_uart.c index df705fda4243..f802867c95c5 100644 --- a/drivers/serial/v850e_uart.c +++ b/drivers/serial/v850e_uart.c @@ -372,13 +372,13 @@ static int v850e_uart_startup (struct uart_port *port) /* Alloc RX irq. */ err = request_irq (V850E_UART_RX_IRQ (port->line), v850e_uart_rx_irq, - SA_INTERRUPT, "v850e_uart", port); + IRQF_DISABLED, "v850e_uart", port); if (err) return err; /* Alloc TX irq. */ err = request_irq (V850E_UART_TX_IRQ (port->line), v850e_uart_tx_irq, - SA_INTERRUPT, "v850e_uart", port); + IRQF_DISABLED, "v850e_uart", port); if (err) { free_irq (V850E_UART_RX_IRQ (port->line), port); return err; @@ -468,7 +468,6 @@ static struct uart_ops v850e_uart_ops = { static struct uart_driver v850e_uart_driver = { .owner = THIS_MODULE, .driver_name = "v850e_uart", - .devfs_name = "tts/", .dev_name = "ttyS", .major = TTY_MAJOR, .minor = V850E_UART_MINOR_BASE, diff --git a/drivers/serial/vr41xx_siu.c b/drivers/serial/vr41xx_siu.c index df5e8713fa31..e93d0edc2e08 100644 --- a/drivers/serial/vr41xx_siu.c +++ b/drivers/serial/vr41xx_siu.c @@ -19,7 +19,6 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include <linux/config.h> #if defined(CONFIG_SERIAL_VR41XX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ @@ -911,7 +910,6 @@ static struct uart_driver siu_uart_driver = { .owner = THIS_MODULE, .driver_name = "SIU", .dev_name = "ttyVR", - .devfs_name = "ttvr/", .major = SIU_MAJOR, .minor = SIU_MINOR_BASE, .cons = SERIAL_VR41XX_CONSOLE, |
