diff options
Diffstat (limited to 'drivers/scsi/ncr53c8xx.h')
| -rw-r--r-- | drivers/scsi/ncr53c8xx.h | 1263 |
1 files changed, 1262 insertions, 1 deletions
diff --git a/drivers/scsi/ncr53c8xx.h b/drivers/scsi/ncr53c8xx.h index 05c7b83cef09..6a7bef2e6118 100644 --- a/drivers/scsi/ncr53c8xx.h +++ b/drivers/scsi/ncr53c8xx.h @@ -2,6 +2,7 @@ ** Device driver for the PCI-SCSI NCR538XX controller family. ** ** Copyright (C) 1994 Wolfgang Stanglmeier +** Copyright (C) 1998-2001 Gerard Roudier <groudier@free.fr> ** ** This program is free software; you can redistribute it and/or modify ** it under the terms of the GNU General Public License as published by @@ -36,15 +37,1275 @@ ** And has been ported to NetBSD by ** Charles M. Hannum <mycroft@gnu.ai.mit.edu> ** +** NVRAM detection and reading. +** Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk> +** +** Added support for MIPS big endian systems. +** Carsten Langgaard, carstenl@mips.com +** Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved. +** +** Added support for HP PARISC big endian systems. +** Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved. +** ******************************************************************************* */ #ifndef NCR53C8XX_H #define NCR53C8XX_H +#include <linux/config.h> #include <scsi/scsi_host.h> -#include "sym53c8xx_defs.h" +/* +** If you want a driver as small as possible, do not define the +** following options. +*/ +#define SCSI_NCR_BOOT_COMMAND_LINE_SUPPORT +#define SCSI_NCR_DEBUG_INFO_SUPPORT + +/* +** To disable integrity checking, do not define the +** following option. +*/ +#ifdef CONFIG_SCSI_NCR53C8XX_INTEGRITY_CHECK +# define SCSI_NCR_ENABLE_INTEGRITY_CHECK +#endif + +/* --------------------------------------------------------------------- +** Take into account kernel configured parameters. +** Most of these options can be overridden at startup by a command line. +** --------------------------------------------------------------------- +*/ + +/* + * For Ultra2 and Ultra3 SCSI support option, use special features. + * + * Value (default) means: + * bit 0 : all features enabled, except: + * bit 1 : PCI Write And Invalidate. + * bit 2 : Data Phase Mismatch handling from SCRIPTS. + * + * Use boot options ncr53c8xx=specf:1 if you want all chip features to be + * enabled by the driver. + */ +#define SCSI_NCR_SETUP_SPECIAL_FEATURES (3) + +#define SCSI_NCR_MAX_SYNC (80) + +/* + * Allow tags from 2 to 256, default 8 + */ +#ifdef CONFIG_SCSI_NCR53C8XX_MAX_TAGS +#if CONFIG_SCSI_NCR53C8XX_MAX_TAGS < 2 +#define SCSI_NCR_MAX_TAGS (2) +#elif CONFIG_SCSI_NCR53C8XX_MAX_TAGS > 256 +#define SCSI_NCR_MAX_TAGS (256) +#else +#define SCSI_NCR_MAX_TAGS CONFIG_SCSI_NCR53C8XX_MAX_TAGS +#endif +#else +#define SCSI_NCR_MAX_TAGS (8) +#endif + +/* + * Allow tagged command queuing support if configured with default number + * of tags set to max (see above). + */ +#ifdef CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS +#define SCSI_NCR_SETUP_DEFAULT_TAGS CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS +#elif defined CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE +#define SCSI_NCR_SETUP_DEFAULT_TAGS SCSI_NCR_MAX_TAGS +#else +#define SCSI_NCR_SETUP_DEFAULT_TAGS (0) +#endif + +/* + * Immediate arbitration + */ +#if defined(CONFIG_SCSI_NCR53C8XX_IARB) +#define SCSI_NCR_IARB_SUPPORT +#endif + +/* + * Sync transfer frequency at startup. + * Allow from 5Mhz to 80Mhz default 20 Mhz. + */ +#ifndef CONFIG_SCSI_NCR53C8XX_SYNC +#define CONFIG_SCSI_NCR53C8XX_SYNC (20) +#elif CONFIG_SCSI_NCR53C8XX_SYNC > SCSI_NCR_MAX_SYNC +#undef CONFIG_SCSI_NCR53C8XX_SYNC +#define CONFIG_SCSI_NCR53C8XX_SYNC SCSI_NCR_MAX_SYNC +#endif + +#if CONFIG_SCSI_NCR53C8XX_SYNC == 0 +#define SCSI_NCR_SETUP_DEFAULT_SYNC (255) +#elif CONFIG_SCSI_NCR53C8XX_SYNC <= 5 +#define SCSI_NCR_SETUP_DEFAULT_SYNC (50) +#elif CONFIG_SCSI_NCR53C8XX_SYNC <= 20 +#define SCSI_NCR_SETUP_DEFAULT_SYNC (250/(CONFIG_SCSI_NCR53C8XX_SYNC)) +#elif CONFIG_SCSI_NCR53C8XX_SYNC <= 33 +#define SCSI_NCR_SETUP_DEFAULT_SYNC (11) +#elif CONFIG_SCSI_NCR53C8XX_SYNC <= 40 +#define SCSI_NCR_SETUP_DEFAULT_SYNC (10) +#else +#define SCSI_NCR_SETUP_DEFAULT_SYNC (9) +#endif + +/* + * Disallow disconnections at boot-up + */ +#ifdef CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT +#define SCSI_NCR_SETUP_DISCONNECTION (0) +#else +#define SCSI_NCR_SETUP_DISCONNECTION (1) +#endif + +/* + * Force synchronous negotiation for all targets + */ +#ifdef CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO +#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO (1) +#else +#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO (0) +#endif + +/* + * Disable master parity checking (flawed hardwares need that) + */ +#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK +#define SCSI_NCR_SETUP_MASTER_PARITY (0) +#else +#define SCSI_NCR_SETUP_MASTER_PARITY (1) +#endif + +/* + * Disable scsi parity checking (flawed devices may need that) + */ +#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK +#define SCSI_NCR_SETUP_SCSI_PARITY (0) +#else +#define SCSI_NCR_SETUP_SCSI_PARITY (1) +#endif + +/* + * Settle time after reset at boot-up + */ +#define SCSI_NCR_SETUP_SETTLE_TIME (2) + +/* +** Bridge quirks work-around option defaulted to 1. +*/ +#ifndef SCSI_NCR_PCIQ_WORK_AROUND_OPT +#define SCSI_NCR_PCIQ_WORK_AROUND_OPT 1 +#endif + +/* +** Work-around common bridge misbehaviour. +** +** - Do not flush posted writes in the opposite +** direction on read. +** - May reorder DMA writes to memory. +** +** This option should not affect performances +** significantly, so it is the default. +*/ +#if SCSI_NCR_PCIQ_WORK_AROUND_OPT == 1 +#define SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM +#define SCSI_NCR_PCIQ_MAY_REORDER_WRITES +#define SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS + +/* +** Same as option 1, but also deal with +** misconfigured interrupts. +** +** - Edge triggerred instead of level sensitive. +** - No interrupt line connected. +** - IRQ number misconfigured. +** +** If no interrupt is delivered, the driver will +** catch the interrupt conditions 10 times per +** second. No need to say that this option is +** not recommended. +*/ +#elif SCSI_NCR_PCIQ_WORK_AROUND_OPT == 2 +#define SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM +#define SCSI_NCR_PCIQ_MAY_REORDER_WRITES +#define SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS +#define SCSI_NCR_PCIQ_BROKEN_INTR + +/* +** Some bridge designers decided to flush +** everything prior to deliver the interrupt. +** This option tries to deal with such a +** behaviour. +*/ +#elif SCSI_NCR_PCIQ_WORK_AROUND_OPT == 3 +#define SCSI_NCR_PCIQ_SYNC_ON_INTR +#endif + +/* +** Other parameters not configurable with "make config" +** Avoid to change these constants, unless you know what you are doing. +*/ + +#define SCSI_NCR_ALWAYS_SIMPLE_TAG +#define SCSI_NCR_MAX_SCATTER (127) +#define SCSI_NCR_MAX_TARGET (16) + +/* +** Compute some desirable value for CAN_QUEUE +** and CMD_PER_LUN. +** The driver will use lower values if these +** ones appear to be too large. +*/ +#define SCSI_NCR_CAN_QUEUE (8*SCSI_NCR_MAX_TAGS + 2*SCSI_NCR_MAX_TARGET) +#define SCSI_NCR_CMD_PER_LUN (SCSI_NCR_MAX_TAGS) + +#define SCSI_NCR_SG_TABLESIZE (SCSI_NCR_MAX_SCATTER) +#define SCSI_NCR_TIMER_INTERVAL (HZ) + +#if 1 /* defined CONFIG_SCSI_MULTI_LUN */ +#define SCSI_NCR_MAX_LUN (16) +#else +#define SCSI_NCR_MAX_LUN (1) +#endif + +/* + * IO functions definition for big/little endian CPU support. + * For now, the NCR is only supported in little endian addressing mode, + */ + +#ifdef __BIG_ENDIAN + +#define inw_l2b inw +#define inl_l2b inl +#define outw_b2l outw +#define outl_b2l outl + +#define readb_raw readb +#define writeb_raw writeb + +#if defined(SCSI_NCR_BIG_ENDIAN) +#define readw_l2b __raw_readw +#define readl_l2b __raw_readl +#define writew_b2l __raw_writew +#define writel_b2l __raw_writel +#define readw_raw __raw_readw +#define readl_raw __raw_readl +#define writew_raw __raw_writew +#define writel_raw __raw_writel +#else /* Other big-endian */ +#define readw_l2b readw +#define readl_l2b readl +#define writew_b2l writew +#define writel_b2l writel +#define readw_raw readw +#define readl_raw readl +#define writew_raw writew +#define writel_raw writel +#endif + +#else /* little endian */ + +#define inw_raw inw +#define inl_raw inl +#define outw_raw outw +#define outl_raw outl + +#define readb_raw readb +#define readw_raw readw +#define readl_raw readl +#define writeb_raw writeb +#define writew_raw writew +#define writel_raw writel + +#endif + +#if !defined(__hppa__) && !defined(__mips__) +#ifdef SCSI_NCR_BIG_ENDIAN +#error "The NCR in BIG ENDIAN addressing mode is not (yet) supported" +#endif +#endif + +#define MEMORY_BARRIER() mb() + + +/* + * If the NCR uses big endian addressing mode over the + * PCI, actual io register addresses for byte and word + * accesses must be changed according to lane routing. + * Btw, ncr_offb() and ncr_offw() macros only apply to + * constants and so donnot generate bloated code. + */ + +#if defined(SCSI_NCR_BIG_ENDIAN) + +#define ncr_offb(o) (((o)&~3)+((~((o)&3))&3)) +#define ncr_offw(o) (((o)&~3)+((~((o)&3))&2)) + +#else + +#define ncr_offb(o) (o) +#define ncr_offw(o) (o) + +#endif + +/* + * If the CPU and the NCR use same endian-ness addressing, + * no byte reordering is needed for script patching. + * Macro cpu_to_scr() is to be used for script patching. + * Macro scr_to_cpu() is to be used for getting a DWORD + * from the script. + */ + +#if defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN) + +#define cpu_to_scr(dw) cpu_to_le32(dw) +#define scr_to_cpu(dw) le32_to_cpu(dw) + +#elif defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN) + +#define cpu_to_scr(dw) cpu_to_be32(dw) +#define scr_to_cpu(dw) be32_to_cpu(dw) + +#else + +#define cpu_to_scr(dw) (dw) +#define scr_to_cpu(dw) (dw) + +#endif + +/* + * Access to the controller chip. + * + * If the CPU and the NCR use same endian-ness addressing, + * no byte reordering is needed for accessing chip io + * registers. Functions suffixed by '_raw' are assumed + * to access the chip over the PCI without doing byte + * reordering. Functions suffixed by '_l2b' are + * assumed to perform little-endian to big-endian byte + * reordering, those suffixed by '_b2l' blah, blah, + * blah, ... + */ + +/* + * MEMORY mapped IO input / output + */ + +#define INB_OFF(o) readb_raw((char __iomem *)np->reg + ncr_offb(o)) +#define OUTB_OFF(o, val) writeb_raw((val), (char __iomem *)np->reg + ncr_offb(o)) + +#if defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN) + +#define INW_OFF(o) readw_l2b((char __iomem *)np->reg + ncr_offw(o)) +#define INL_OFF(o) readl_l2b((char __iomem *)np->reg + (o)) + +#define OUTW_OFF(o, val) writew_b2l((val), (char __iomem *)np->reg + ncr_offw(o)) +#define OUTL_OFF(o, val) writel_b2l((val), (char __iomem *)np->reg + (o)) + +#elif defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN) + +#define INW_OFF(o) readw_b2l((char __iomem *)np->reg + ncr_offw(o)) +#define INL_OFF(o) readl_b2l((char __iomem *)np->reg + (o)) + +#define OUTW_OFF(o, val) writew_l2b((val), (char __iomem *)np->reg + ncr_offw(o)) +#define OUTL_OFF(o, val) writel_l2b((val), (char __iomem *)np->reg + (o)) + +#else + +#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS +/* Only 8 or 32 bit transfers allowed */ +#define INW_OFF(o) (readb((char __iomem *)np->reg + ncr_offw(o)) << 8 | readb((char __iomem *)np->reg + ncr_offw(o) + 1)) +#else +#define INW_OFF(o) readw_raw((char __iomem *)np->reg + ncr_offw(o)) +#endif +#define INL_OFF(o) readl_raw((char __iomem *)np->reg + (o)) + +#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS +/* Only 8 or 32 bit transfers allowed */ +#define OUTW_OFF(o, val) do { writeb((char)((val) >> 8), (char __iomem *)np->reg + ncr_offw(o)); writeb((char)(val), (char __iomem *)np->reg + ncr_offw(o) + 1); } while (0) +#else +#define OUTW_OFF(o, val) writew_raw((val), (char __iomem *)np->reg + ncr_offw(o)) +#endif +#define OUTL_OFF(o, val) writel_raw((val), (char __iomem *)np->reg + (o)) + +#endif + +#define INB(r) INB_OFF (offsetof(struct ncr_reg,r)) +#define INW(r) INW_OFF (offsetof(struct ncr_reg,r)) +#define INL(r) INL_OFF (offsetof(struct ncr_reg,r)) + +#define OUTB(r, val) OUTB_OFF (offsetof(struct ncr_reg,r), (val)) +#define OUTW(r, val) OUTW_OFF (offsetof(struct ncr_reg,r), (val)) +#define OUTL(r, val) OUTL_OFF (offsetof(struct ncr_reg,r), (val)) + +/* + * Set bit field ON, OFF + */ + +#define OUTONB(r, m) OUTB(r, INB(r) | (m)) +#define OUTOFFB(r, m) OUTB(r, INB(r) & ~(m)) +#define OUTONW(r, m) OUTW(r, INW(r) | (m)) +#define OUTOFFW(r, m) OUTW(r, INW(r) & ~(m)) +#define OUTONL(r, m) OUTL(r, INL(r) | (m)) +#define OUTOFFL(r, m) OUTL(r, INL(r) & ~(m)) + +/* + * We normally want the chip to have a consistent view + * of driver internal data structures when we restart it. + * Thus these macros. + */ +#define OUTL_DSP(v) \ + do { \ + MEMORY_BARRIER(); \ + OUTL (nc_dsp, (v)); \ + } while (0) + +#define OUTONB_STD() \ + do { \ + MEMORY_BARRIER(); \ + OUTONB (nc_dcntl, (STD|NOCOM)); \ + } while (0) + + +/* +** NCR53C8XX devices features table. +*/ +struct ncr_chip { + unsigned short revision_id; + unsigned char burst_max; /* log-base-2 of max burst */ + unsigned char offset_max; + unsigned char nr_divisor; + unsigned int features; +#define FE_LED0 (1<<0) +#define FE_WIDE (1<<1) /* Wide data transfers */ +#define FE_ULTRA (1<<2) /* Ultra speed 20Mtrans/sec */ +#define FE_DBLR (1<<4) /* Clock doubler present */ +#define FE_QUAD (1<<5) /* Clock quadrupler present */ +#define FE_ERL (1<<6) /* Enable read line */ +#define FE_CLSE (1<<7) /* Cache line size enable */ +#define FE_WRIE (1<<8) /* Write & Invalidate enable */ +#define FE_ERMP (1<<9) /* Enable read multiple */ +#define FE_BOF (1<<10) /* Burst opcode fetch */ +#define FE_DFS (1<<11) /* DMA fifo size */ +#define FE_PFEN (1<<12) /* Prefetch enable */ +#define FE_LDSTR (1<<13) /* Load/Store supported */ +#define FE_RAM (1<<14) /* On chip RAM present */ +#define FE_VARCLK (1<<15) /* SCSI clock may vary */ +#define FE_RAM8K (1<<16) /* On chip RAM sized 8Kb */ +#define FE_64BIT (1<<17) /* Have a 64-bit PCI interface */ +#define FE_IO256 (1<<18) /* Requires full 256 bytes in PCI space */ +#define FE_NOPM (1<<19) /* Scripts handles phase mismatch */ +#define FE_LEDC (1<<20) /* Hardware control of LED */ +#define FE_DIFF (1<<21) /* Support Differential SCSI */ +#define FE_66MHZ (1<<23) /* 66MHz PCI Support */ +#define FE_DAC (1<<24) /* Support DAC cycles (64 bit addressing) */ +#define FE_ISTAT1 (1<<25) /* Have ISTAT1, MBOX0, MBOX1 registers */ +#define FE_DAC_IN_USE (1<<26) /* Platform does DAC cycles */ +#define FE_EHP (1<<27) /* 720: Even host parity */ +#define FE_MUX (1<<28) /* 720: Multiplexed bus */ +#define FE_EA (1<<29) /* 720: Enable Ack */ + +#define FE_CACHE_SET (FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP) +#define FE_SCSI_SET (FE_WIDE|FE_ULTRA|FE_DBLR|FE_QUAD|F_CLK80) +#define FE_SPECIAL_SET (FE_CACHE_SET|FE_BOF|FE_DFS|FE_LDSTR|FE_PFEN|FE_RAM) +}; + + +/* +** Driver setup structure. +** +** This structure is initialized from linux config options. +** It can be overridden at boot-up by the boot command line. +*/ +#define SCSI_NCR_MAX_EXCLUDES 8 +struct ncr_driver_setup { + u8 master_parity; + u8 scsi_parity; + u8 disconnection; + u8 special_features; + u8 force_sync_nego; + u8 reverse_probe; + u8 pci_fix_up; + u8 use_nvram; + u8 verbose; + u8 default_tags; + u16 default_sync; + u16 debug; + u8 burst_max; + u8 led_pin; + u8 max_wide; + u8 settle_delay; + u8 diff_support; + u8 irqm; + u8 bus_check; + u8 optimize; + u8 recovery; + u8 host_id; + u16 iarb; + u32 excludes[SCSI_NCR_MAX_EXCLUDES]; + char tag_ctrl[100]; +}; + +/* +** Initial setup. +** Can be overriden at startup by a command line. +*/ +#define SCSI_NCR_DRIVER_SETUP \ +{ \ + SCSI_NCR_SETUP_MASTER_PARITY, \ + SCSI_NCR_SETUP_SCSI_PARITY, \ + SCSI_NCR_SETUP_DISCONNECTION, \ + SCSI_NCR_SETUP_SPECIAL_FEATURES, \ + SCSI_NCR_SETUP_FORCE_SYNC_NEGO, \ + 0, \ + 0, \ + 1, \ + 0, \ + SCSI_NCR_SETUP_DEFAULT_TAGS, \ + SCSI_NCR_SETUP_DEFAULT_SYNC, \ + 0x00, \ + 7, \ + 0, \ + 1, \ + SCSI_NCR_SETUP_SETTLE_TIME, \ + 0, \ + 0, \ + 1, \ + 0, \ + 0, \ + 255, \ + 0x00 \ +} + +/* +** Boot fail safe setup. +** Override initial setup from boot command line: +** ncr53c8xx=safe:y +*/ +#define SCSI_NCR_DRIVER_SAFE_SETUP \ +{ \ + 0, \ + 1, \ + 0, \ + 0, \ + 0, \ + 0, \ + 0, \ + 1, \ + 2, \ + 0, \ + 255, \ + 0x00, \ + 255, \ + 0, \ + 0, \ + 10, \ + 1, \ + 1, \ + 1, \ + 0, \ + 0, \ + 255 \ +} + +/**************** ORIGINAL CONTENT of ncrreg.h from FreeBSD ******************/ + +/*----------------------------------------------------------------- +** +** The ncr 53c810 register structure. +** +**----------------------------------------------------------------- +*/ + +struct ncr_reg { +/*00*/ u8 nc_scntl0; /* full arb., ena parity, par->ATN */ + +/*01*/ u8 nc_scntl1; /* no reset */ + #define ISCON 0x10 /* connected to scsi */ + #define CRST 0x08 /* force reset */ + #define IARB 0x02 /* immediate arbitration */ + +/*02*/ u8 nc_scntl2; /* no disconnect expected */ + #define SDU 0x80 /* cmd: disconnect will raise error */ + #define CHM 0x40 /* sta: chained mode */ + #define WSS 0x08 /* sta: wide scsi send [W]*/ + #define WSR 0x01 /* sta: wide scsi received [W]*/ + +/*03*/ u8 nc_scntl3; /* cnf system clock dependent */ + #define EWS 0x08 /* cmd: enable wide scsi [W]*/ + #define ULTRA 0x80 /* cmd: ULTRA enable */ + /* bits 0-2, 7 rsvd for C1010 */ + +/*04*/ u8 nc_scid; /* cnf host adapter scsi address */ + #define RRE 0x40 /* r/w:e enable response to resel. */ + #define SRE 0x20 /* r/w:e enable response to select */ + +/*05*/ u8 nc_sxfer; /* ### Sync speed and count */ + /* bits 6-7 rsvd for C1010 */ + +/*06*/ u8 nc_sdid; /* ### Destination-ID */ + +/*07*/ u8 nc_gpreg; /* ??? IO-Pins */ + +/*08*/ u8 nc_sfbr; /* ### First byte in phase */ + +/*09*/ u8 nc_socl; + #define CREQ 0x80 /* r/w: SCSI-REQ */ + #define CACK 0x40 /* r/w: SCSI-ACK */ + #define CBSY 0x20 /* r/w: SCSI-BSY */ + #define CSEL 0x10 /* r/w: SCSI-SEL */ + #define CATN 0x08 /* r/w: SCSI-ATN */ + #define CMSG 0x04 /* r/w: SCSI-MSG */ + #define CC_D 0x02 /* r/w: SCSI-C_D */ + #define CI_O 0x01 /* r/w: SCSI-I_O */ + +/*0a*/ u8 nc_ssid; + +/*0b*/ u8 nc_sbcl; + +/*0c*/ u8 nc_dstat; + #define DFE 0x80 /* sta: dma fifo empty */ + #define MDPE 0x40 /* int: master data parity error */ + #define BF 0x20 /* int: script: bus fault */ + #define ABRT 0x10 /* int: script: command aborted */ + #define SSI 0x08 /* int: script: single step */ + #define SIR 0x04 /* int: script: interrupt instruct. */ + #define IID 0x01 /* int: script: illegal instruct. */ + +/*0d*/ u8 nc_sstat0; + #define ILF 0x80 /* sta: data in SIDL register lsb */ + #define ORF 0x40 /* sta: data in SODR register lsb */ + #define OLF 0x20 /* sta: data in SODL register lsb */ + #define AIP 0x10 /* sta: arbitration in progress */ + #define LOA 0x08 /* sta: arbitration lost */ + #define WOA 0x04 /* sta: arbitration won */ + #define IRST 0x02 /* sta: scsi reset signal */ + #define SDP 0x01 /* sta: scsi parity signal */ + +/*0e*/ u8 nc_sstat1; + #define FF3210 0xf0 /* sta: bytes in the scsi fifo */ + +/*0f*/ u8 nc_sstat2; + #define ILF1 0x80 /* sta: data in SIDL register msb[W]*/ + #define ORF1 0x40 /* sta: data in SODR register msb[W]*/ + #define OLF1 0x20 /* sta: data in SODL register msb[W]*/ + #define DM 0x04 /* sta: DIFFSENS mismatch (895/6 only) */ + #define LDSC 0x02 /* sta: disconnect & reconnect */ + +/*10*/ u8 nc_dsa; /* --> Base page */ +/*11*/ u8 nc_dsa1; +/*12*/ u8 nc_dsa2; +/*13*/ u8 nc_dsa3; + +/*14*/ u8 nc_istat; /* --> Main Command and status */ + #define CABRT 0x80 /* cmd: abort current operation */ + #define SRST 0x40 /* mod: reset chip */ + #define SIGP 0x20 /* r/w: message from host to ncr */ + #define SEM 0x10 /* r/w: message between host + ncr */ + #define CON 0x08 /* sta: connected to scsi */ + #define INTF 0x04 /* sta: int on the fly (reset by wr)*/ + #define SIP 0x02 /* sta: scsi-interrupt */ + #define DIP 0x01 /* sta: host/script interrupt */ + +/*15*/ u8 nc_istat1; /* 896 and later cores only */ + #define FLSH 0x04 /* sta: chip is flushing */ + #define SRUN 0x02 /* sta: scripts are running */ + #define SIRQD 0x01 /* r/w: disable INT pin */ + +/*16*/ u8 nc_mbox0; /* 896 and later cores only */ +/*17*/ u8 nc_mbox1; /* 896 and later cores only */ + +/*18*/ u8 nc_ctest0; + #define EHP 0x04 /* 720 even host parity */ +/*19*/ u8 nc_ctest1; + +/*1a*/ u8 nc_ctest2; + #define CSIGP 0x40 + /* bits 0-2,7 rsvd for C1010 */ + +/*1b*/ u8 nc_ctest3; + #define FLF 0x08 /* cmd: flush dma fifo */ + #define CLF 0x04 /* cmd: clear dma fifo */ + #define FM 0x02 /* mod: fetch pin mode */ + #define WRIE 0x01 /* mod: write and invalidate enable */ + /* bits 4-7 rsvd for C1010 */ + +/*1c*/ u32 nc_temp; /* ### Temporary stack */ + +/*20*/ u8 nc_dfifo; +/*21*/ u8 nc_ctest4; + #define MUX 0x80 /* 720 host bus multiplex mode */ + #define BDIS 0x80 /* mod: burst disable */ + #define MPEE 0x08 /* mod: master parity error enable */ + +/*22*/ u8 nc_ctest5; + #define DFS 0x20 /* mod: dma fifo size */ + /* bits 0-1, 3-7 rsvd for C1010 */ +/*23*/ u8 nc_ctest6; + +/*24*/ u32 nc_dbc; /* ### Byte count and command */ +/*28*/ u32 nc_dnad; /* ### Next command register */ +/*2c*/ u32 nc_dsp; /* --> Script Pointer */ +/*30*/ u32 nc_dsps; /* --> Script pointer save/opcode#2 */ + +/*34*/ u8 nc_scratcha; /* Temporary register a */ +/*35*/ u8 nc_scratcha1; +/*36*/ u8 nc_scratcha2; +/*37*/ u8 nc_scratcha3; + +/*38*/ u8 nc_dmode; + #define BL_2 0x80 /* mod: burst length shift value +2 */ + #define BL_1 0x40 /* mod: burst length shift value +1 */ + #define ERL 0x08 /* mod: enable read line */ + #define ERMP 0x04 /* mod: enable read multiple */ + #define BOF 0x02 /* mod: burst op code fetch */ + +/*39*/ u8 nc_dien; +/*3a*/ u8 nc_sbr; + +/*3b*/ u8 nc_dcntl; /* --> Script execution control */ + #define CLSE 0x80 /* mod: cache line size enable */ + #define PFF 0x40 /* cmd: pre-fetch flush */ + #define PFEN 0x20 /* mod: pre-fetch enable */ + #define EA 0x20 /* mod: 720 enable-ack */ + #define SSM 0x10 /* mod: single step mode */ + #define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */ + #define STD 0x04 /* cmd: start dma mode */ + #define IRQD 0x02 /* mod: irq disable */ + #define NOCOM 0x01 /* cmd: protect sfbr while reselect */ + /* bits 0-1 rsvd for C1010 */ + +/*3c*/ u32 nc_adder; + +/*40*/ u16 nc_sien; /* -->: interrupt enable */ +/*42*/ u16 nc_sist; /* <--: interrupt status */ + #define SBMC 0x1000/* sta: SCSI Bus Mode Change (895/6 only) */ + #define STO 0x0400/* sta: timeout (select) */ + #define GEN 0x0200/* sta: timeout (general) */ + #define HTH 0x0100/* sta: timeout (handshake) */ + #define MA 0x80 /* sta: phase mismatch */ + #define CMP 0x40 /* sta: arbitration complete */ + #define SEL 0x20 /* sta: selected by another device */ + #define RSL 0x10 /* sta: reselected by another device*/ + #define SGE 0x08 /* sta: gross error (over/underflow)*/ + #define UDC 0x04 /* sta: unexpected disconnect */ + #define RST 0x02 /* sta: scsi bus reset detected */ + #define PAR 0x01 /* sta: scsi parity error */ + +/*44*/ u8 nc_slpar; +/*45*/ u8 nc_swide; +/*46*/ u8 nc_macntl; +/*47*/ u8 nc_gpcntl; +/*48*/ u8 nc_stime0; /* cmd: timeout for select&handshake*/ +/*49*/ u8 nc_stime1; /* cmd: timeout user defined */ +/*4a*/ u16 nc_respid; /* sta: Reselect-IDs */ + +/*4c*/ u8 nc_stest0; + +/*4d*/ u8 nc_stest1; + #define SCLK 0x80 /* Use the PCI clock as SCSI clock */ + #define DBLEN 0x08 /* clock doubler running */ + #define DBLSEL 0x04 /* clock doubler selected */ + + +/*4e*/ u8 nc_stest2; + #define ROF 0x40 /* reset scsi offset (after gross error!) */ + #define DIF 0x20 /* 720 SCSI differential mode */ + #define EXT 0x02 /* extended filtering */ + +/*4f*/ u8 nc_stest3; + #define TE 0x80 /* c: tolerAnt enable */ + #define HSC 0x20 /* c: Halt SCSI Clock */ + #define CSF 0x02 /* c: clear scsi fifo */ + +/*50*/ u16 nc_sidl; /* Lowlevel: latched from scsi data */ +/*52*/ u8 nc_stest4; + #define SMODE 0xc0 /* SCSI bus mode (895/6 only) */ + #define SMODE_HVD 0x40 /* High Voltage Differential */ + #define SMODE_SE 0x80 /* Single Ended */ + #define SMODE_LVD 0xc0 /* Low Voltage Differential */ + #define LCKFRQ 0x20 /* Frequency Lock (895/6 only) */ + /* bits 0-5 rsvd for C1010 */ + +/*53*/ u8 nc_53_; +/*54*/ u16 nc_sodl; /* Lowlevel: data out to scsi data */ +/*56*/ u8 nc_ccntl0; /* Chip Control 0 (896) */ + #define ENPMJ 0x80 /* Enable Phase Mismatch Jump */ + #define PMJCTL 0x40 /* Phase Mismatch Jump Control */ + #define ENNDJ 0x20 /* Enable Non Data PM Jump */ + #define DISFC 0x10 /* Disable Auto FIFO Clear */ + #define DILS 0x02 /* Disable Internal Load/Store */ + #define DPR 0x01 /* Disable Pipe Req */ + +/*57*/ u8 nc_ccntl1; /* Chip Control 1 (896) */ + #define ZMOD 0x80 /* High Impedance Mode */ + #define DIC 0x10 /* Disable Internal Cycles */ + #define DDAC 0x08 /* Disable Dual Address Cycle */ + #define XTIMOD 0x04 /* 64-bit Table Ind. Indexing Mode */ + #define EXTIBMV 0x02 /* Enable 64-bit Table Ind. BMOV */ + #define EXDBMV 0x01 /* Enable 64-bit Direct BMOV */ + +/*58*/ u16 nc_sbdl; /* Lowlevel: data from scsi data */ +/*5a*/ u16 nc_5a_; + +/*5c*/ u8 nc_scr0; /* Working register B */ +/*5d*/ u8 nc_scr1; /* */ +/*5e*/ u8 nc_scr2; /* */ +/*5f*/ u8 nc_scr3; /* */ + +/*60*/ u8 nc_scrx[64]; /* Working register C-R */ +/*a0*/ u32 nc_mmrs; /* Memory Move Read Selector */ +/*a4*/ u32 nc_mmws; /* Memory Move Write Selector */ +/*a8*/ u32 nc_sfs; /* Script Fetch Selector */ +/*ac*/ u32 nc_drs; /* DSA Relative Selector */ +/*b0*/ u32 nc_sbms; /* Static Block Move Selector */ +/*b4*/ u32 nc_dbms; /* Dynamic Block Move Selector */ +/*b8*/ u32 nc_dnad64; /* DMA Next Address 64 */ +/*bc*/ u16 nc_scntl4; /* C1010 only */ + #define U3EN 0x80 /* Enable Ultra 3 */ + #define AIPEN 0x40 /* Allow check upper byte lanes */ + #define XCLKH_DT 0x08 /* Extra clock of data hold on DT + transfer edge */ + #define XCLKH_ST 0x04 /* Extra clock of data hold on ST + transfer edge */ + +/*be*/ u8 nc_aipcntl0; /* Epat Control 1 C1010 only */ +/*bf*/ u8 nc_aipcntl1; /* AIP Control C1010_66 Only */ + +/*c0*/ u32 nc_pmjad1; /* Phase Mismatch Jump Address 1 */ +/*c4*/ u32 nc_pmjad2; /* Phase Mismatch Jump Address 2 */ +/*c8*/ u8 nc_rbc; /* Remaining Byte Count */ +/*c9*/ u8 nc_rbc1; /* */ +/*ca*/ u8 nc_rbc2; /* */ +/*cb*/ u8 nc_rbc3; /* */ + +/*cc*/ u8 nc_ua; /* Updated Address */ +/*cd*/ u8 nc_ua1; /* */ +/*ce*/ u8 nc_ua2; /* */ +/*cf*/ u8 nc_ua3; /* */ +/*d0*/ u32 nc_esa; /* Entry Storage Address */ +/*d4*/ u8 nc_ia; /* Instruction Address */ +/*d5*/ u8 nc_ia1; +/*d6*/ u8 nc_ia2; +/*d7*/ u8 nc_ia3; +/*d8*/ u32 nc_sbc; /* SCSI Byte Count (3 bytes only) */ +/*dc*/ u32 nc_csbc; /* Cumulative SCSI Byte Count */ + + /* Following for C1010 only */ +/*e0*/ u16 nc_crcpad; /* CRC Value */ +/*e2*/ u8 nc_crccntl0; /* CRC control register */ + #define SNDCRC 0x10 /* Send CRC Request */ +/*e3*/ u8 nc_crccntl1; /* CRC control register */ +/*e4*/ u32 nc_crcdata; /* CRC data register */ +/*e8*/ u32 nc_e8_; /* rsvd */ +/*ec*/ u32 nc_ec_; /* rsvd */ +/*f0*/ u16 nc_dfbc; /* DMA FIFO byte count */ + +}; + +/*----------------------------------------------------------- +** +** Utility macros for the script. +** +**----------------------------------------------------------- +*/ + +#define REGJ(p,r) (offsetof(struct ncr_reg, p ## r)) +#define REG(r) REGJ (nc_, r) + +typedef u32 ncrcmd; + +/*----------------------------------------------------------- +** +** SCSI phases +** +** DT phases illegal for ncr driver. +** +**----------------------------------------------------------- +*/ + +#define SCR_DATA_OUT 0x00000000 +#define SCR_DATA_IN 0x01000000 +#define SCR_COMMAND 0x02000000 +#define SCR_STATUS 0x03000000 +#define SCR_DT_DATA_OUT 0x04000000 +#define SCR_DT_DATA_IN 0x05000000 +#define SCR_MSG_OUT 0x06000000 +#define SCR_MSG_IN 0x07000000 + +#define SCR_ILG_OUT 0x04000000 +#define SCR_ILG_IN 0x05000000 + +/*----------------------------------------------------------- +** +** Data transfer via SCSI. +** +**----------------------------------------------------------- +** +** MOVE_ABS (LEN) +** <<start address>> +** +** MOVE_IND (LEN) +** <<dnad_offset>> +** +** MOVE_TBL +** <<dnad_offset>> +** +**----------------------------------------------------------- +*/ + +#define OPC_MOVE 0x08000000 + +#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l)) +#define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) +#define SCR_MOVE_TBL (0x10000000 | OPC_MOVE) + +#define SCR_CHMOV_ABS(l) ((0x00000000) | (l)) +#define SCR_CHMOV_IND(l) ((0x20000000) | (l)) +#define SCR_CHMOV_TBL (0x10000000) + +struct scr_tblmove { + u32 size; + u32 addr; +}; + +/*----------------------------------------------------------- +** +** Selection +** +**----------------------------------------------------------- +** +** SEL_ABS | SCR_ID (0..15) [ | REL_JMP] +** <<alternate_address>> +** +** SEL_TBL | << dnad_offset>> [ | REL_JMP] +** <<alternate_address>> +** +**----------------------------------------------------------- +*/ + +#define SCR_SEL_ABS 0x40000000 +#define SCR_SEL_ABS_ATN 0x41000000 +#define SCR_SEL_TBL 0x42000000 +#define SCR_SEL_TBL_ATN 0x43000000 + + +#ifdef SCSI_NCR_BIG_ENDIAN +struct scr_tblsel { + u8 sel_scntl3; + u8 sel_id; + u8 sel_sxfer; + u8 sel_scntl4; +}; +#else +struct scr_tblsel { + u8 sel_scntl4; + u8 sel_sxfer; + u8 sel_id; + u8 sel_scntl3; +}; +#endif + +#define SCR_JMP_REL 0x04000000 +#define SCR_ID(id) (((u32)(id)) << 16) + +/*----------------------------------------------------------- +** +** Waiting for Disconnect or Reselect +** +**----------------------------------------------------------- +** +** WAIT_DISC +** dummy: <<alternate_address>> +** +** WAIT_RESEL +** <<alternate_address>> +** +**----------------------------------------------------------- +*/ + +#define SCR_WAIT_DISC 0x48000000 +#define SCR_WAIT_RESEL 0x50000000 + +/*----------------------------------------------------------- +** +** Bit Set / Reset +** +**----------------------------------------------------------- +** +** SET (flags {|.. }) +** +** CLR (flags {|.. }) +** +**----------------------------------------------------------- +*/ + +#define SCR_SET(f) (0x58000000 | (f)) +#define SCR_CLR(f) (0x60000000 | (f)) + +#define SCR_CARRY 0x00000400 +#define SCR_TRG 0x00000200 +#define SCR_ACK 0x00000040 +#define SCR_ATN 0x00000008 + + + + +/*----------------------------------------------------------- +** +** Memory to memory move +** +**----------------------------------------------------------- +** +** COPY (bytecount) +** << source_address >> +** << destination_address >> +** +** SCR_COPY sets the NO FLUSH option by default. +** SCR_COPY_F does not set this option. +** +** For chips which do not support this option, +** ncr_copy_and_bind() will remove this bit. +**----------------------------------------------------------- +*/ + +#define SCR_NO_FLUSH 0x01000000 + +#define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n)) +#define SCR_COPY_F(n) (0xc0000000 | (n)) + +/*----------------------------------------------------------- +** +** Register move and binary operations +** +**----------------------------------------------------------- +** +** SFBR_REG (reg, op, data) reg = SFBR op data +** << 0 >> +** +** REG_SFBR (reg, op, data) SFBR = reg op data +** << 0 >> +** +** REG_REG (reg, op, data) reg = reg op data +** << 0 >> +** +**----------------------------------------------------------- +** On 810A, 860, 825A, 875, 895 and 896 chips the content +** of SFBR register can be used as data (SCR_SFBR_DATA). +** The 896 has additionnal IO registers starting at +** offset 0x80. Bit 7 of register offset is stored in +** bit 7 of the SCRIPTS instruction first DWORD. +**----------------------------------------------------------- +*/ + +#define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80)) + +#define SCR_SFBR_REG(reg,op,data) \ + (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) + +#define SCR_REG_SFBR(reg,op,data) \ + (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) + +#define SCR_REG_REG(reg,op,data) \ + (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) + + +#define SCR_LOAD 0x00000000 +#define SCR_SHL 0x01000000 +#define SCR_OR 0x02000000 +#define SCR_XOR 0x03000000 +#define SCR_AND 0x04000000 +#define SCR_SHR 0x05000000 +#define SCR_ADD 0x06000000 +#define SCR_ADDC 0x07000000 + +#define SCR_SFBR_DATA (0x00800000>>8ul) /* Use SFBR as data */ + +/*----------------------------------------------------------- +** +** FROM_REG (reg) SFBR = reg +** << 0 >> +** +** TO_REG (reg) reg = SFBR +** << 0 >> +** +** LOAD_REG (reg, data) reg = <data> +** << 0 >> +** +** LOAD_SFBR(data) SFBR = <data> +** << 0 >> +** +**----------------------------------------------------------- +*/ + +#define SCR_FROM_REG(reg) \ + SCR_REG_SFBR(reg,SCR_OR,0) + +#define SCR_TO_REG(reg) \ + SCR_SFBR_REG(reg,SCR_OR,0) + +#define SCR_LOAD_REG(reg,data) \ + SCR_REG_REG(reg,SCR_LOAD,data) + +#define SCR_LOAD_SFBR(data) \ + (SCR_REG_SFBR (gpreg, SCR_LOAD, data)) + +/*----------------------------------------------------------- +** +** LOAD from memory to register. +** STORE from register to memory. +** +** Only supported by 810A, 860, 825A, 875, 895 and 896. +** +**----------------------------------------------------------- +** +** LOAD_ABS (LEN) +** <<start address>> +** +** LOAD_REL (LEN) (DSA relative) +** <<dsa_offset>> +** +**----------------------------------------------------------- +*/ + +#define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul) +#define SCR_NO_FLUSH2 0x02000000 +#define SCR_DSA_REL2 0x10000000 + +#define SCR_LOAD_R(reg, how, n) \ + (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) + +#define SCR_STORE_R(reg, how, n) \ + (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) + +#define SCR_LOAD_ABS(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2, n) +#define SCR_LOAD_REL(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n) +#define SCR_LOAD_ABS_F(reg, n) SCR_LOAD_R(reg, 0, n) +#define SCR_LOAD_REL_F(reg, n) SCR_LOAD_R(reg, SCR_DSA_REL2, n) + +#define SCR_STORE_ABS(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2, n) +#define SCR_STORE_REL(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n) +#define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n) +#define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n) + + +/*----------------------------------------------------------- +** +** Waiting for Disconnect or Reselect +** +**----------------------------------------------------------- +** +** JUMP [ | IFTRUE/IFFALSE ( ... ) ] +** <<address>> +** +** JUMPR [ | IFTRUE/IFFALSE ( ... ) ] +** <<distance>> +** +** CALL [ | IFTRUE/IFFALSE ( ... ) ] +** <<address>> +** +** CALLR [ | IFTRUE/IFFALSE ( ... ) ] +** <<distance>> +** +** RETURN [ | IFTRUE/IFFALSE ( ... ) ] +** <<dummy>> +** +** INT [ | IFTRUE/IFFALSE ( ... ) ] +** <<ident>> +** +** INT_FLY [ | IFTRUE/IFFALSE ( ... ) ] +** <<ident>> +** +** Conditions: +** WHEN (phase) +** IF (phase) +** CARRYSET +** DATA (data, mask) +** +**----------------------------------------------------------- +*/ + +#define SCR_NO_OP 0x80000000 +#define SCR_JUMP 0x80080000 +#define SCR_JUMP64 0x80480000 +#define SCR_JUMPR 0x80880000 +#define SCR_CALL 0x88080000 +#define SCR_CALLR 0x88880000 +#define SCR_RETURN 0x90080000 +#define SCR_INT 0x98080000 +#define SCR_INT_FLY 0x98180000 + +#define IFFALSE(arg) (0x00080000 | (arg)) +#define IFTRUE(arg) (0x00000000 | (arg)) + +#define WHEN(phase) (0x00030000 | (phase)) +#define IF(phase) (0x00020000 | (phase)) + +#define DATA(D) (0x00040000 | ((D) & 0xff)) +#define MASK(D,M) (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff)) + +#define CARRYSET (0x00200000) + +/*----------------------------------------------------------- +** +** SCSI constants. +** +**----------------------------------------------------------- +*/ + +/* +** Messages +*/ + +#define M_COMPLETE COMMAND_COMPLETE +#define M_EXTENDED EXTENDED_MESSAGE +#define M_SAVE_DP SAVE_POINTERS +#define M_RESTORE_DP RESTORE_POINTERS +#define M_DISCONNECT DISCONNECT +#define M_ID_ERROR INITIATOR_ERROR +#define M_ABORT ABORT_TASK_SET +#define M_REJECT MESSAGE_REJECT +#define M_NOOP NOP +#define M_PARITY MSG_PARITY_ERROR +#define M_LCOMPLETE LINKED_CMD_COMPLETE +#define M_FCOMPLETE LINKED_FLG_CMD_COMPLETE +#define M_RESET TARGET_RESET +#define M_ABORT_TAG ABORT_TASK +#define M_CLEAR_QUEUE CLEAR_TASK_SET +#define M_INIT_REC INITIATE_RECOVERY +#define M_REL_REC RELEASE_RECOVERY +#define M_TERMINATE (0x11) +#define M_SIMPLE_TAG SIMPLE_QUEUE_TAG +#define M_HEAD_TAG HEAD_OF_QUEUE_TAG +#define M_ORDERED_TAG ORDERED_QUEUE_TAG +#define M_IGN_RESIDUE IGNORE_WIDE_RESIDUE +#define M_IDENTIFY (0x80) + +#define M_X_MODIFY_DP EXTENDED_MODIFY_DATA_POINTER +#define M_X_SYNC_REQ EXTENDED_SDTR +#define M_X_WIDE_REQ EXTENDED_WDTR +#define M_X_PPR_REQ EXTENDED_PPR + +/* +** Status +*/ + +#define S_GOOD (0x00) +#define S_CHECK_COND (0x02) +#define S_COND_MET (0x04) +#define S_BUSY (0x08) +#define S_INT (0x10) +#define S_INT_COND_MET (0x14) +#define S_CONFLICT (0x18) +#define S_TERMINATED (0x20) +#define S_QUEUE_FULL (0x28) +#define S_ILLEGAL (0xff) +#define S_SENSE (0x80) + +/* + * End of ncrreg from FreeBSD + */ /* Build a scatter/gather entry. |
