diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/reg.h')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/reg.h | 42 |
1 files changed, 29 insertions, 13 deletions
diff --git a/drivers/net/wireless/ath/ath5k/reg.h b/drivers/net/wireless/ath/ath5k/reg.h index 1464f89b249c..55b4ac6d236f 100644 --- a/drivers/net/wireless/ath/ath5k/reg.h +++ b/drivers/net/wireless/ath/ath5k/reg.h @@ -212,10 +212,10 @@ * MIB control register */ #define AR5K_MIBC 0x0040 /* Register Address */ -#define AR5K_MIBC_COW 0x00000001 /* Warn test indicator */ +#define AR5K_MIBC_COW 0x00000001 /* Counter Overflow Warning */ #define AR5K_MIBC_FMC 0x00000002 /* Freeze MIB Counters */ -#define AR5K_MIBC_CMC 0x00000004 /* Clean MIB Counters */ -#define AR5K_MIBC_MCS 0x00000008 /* MIB counter strobe */ +#define AR5K_MIBC_CMC 0x00000004 /* Clear MIB Counters */ +#define AR5K_MIBC_MCS 0x00000008 /* MIB counter strobe, increment all */ /* * Timeout prescale register @@ -1139,8 +1139,8 @@ #define AR5K_STA_ID1_DEFAULT_ANTENNA 0x00200000 /* Use default antenna */ #define AR5K_STA_ID1_DESC_ANTENNA 0x00400000 /* Update antenna from descriptor */ #define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS */ -#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS */ -#define AR5K_STA_ID1_BASE_RATE_11B 0x02000000 /* Use 11b base rate for ACK/CTS [5211+] */ +#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Rate to use for ACK/CTS. 0: highest mandatory rate <= RX rate; 1: 1Mbps in B mode */ +#define AR5K_STA_ID1_BASE_RATE_11B 0x02000000 /* 802.11b base rate. 0: 1, 2, 5.5 and 11Mbps; 1: 1 and 2Mbps. [5211+] */ #define AR5K_STA_ID1_SELFGEN_DEF_ANT 0x04000000 /* Use def. antenna for self generated frames */ #define AR5K_STA_ID1_CRYPT_MIC_EN 0x08000000 /* Enable MIC */ #define AR5K_STA_ID1_KEYSRCH_MODE 0x10000000 /* Look up key when key id != 0 */ @@ -1516,7 +1516,14 @@ AR5K_NAV_5210 : AR5K_NAV_5211) /* - * RTS success register + * MIB counters: + * + * max value is 0xc000, if this is reached we get a MIB interrupt. + * they can be controlled via AR5K_MIBC and are cleared on read. + */ + +/* + * RTS success (MIB counter) */ #define AR5K_RTS_OK_5210 0x8090 #define AR5K_RTS_OK_5211 0x8088 @@ -1524,7 +1531,7 @@ AR5K_RTS_OK_5210 : AR5K_RTS_OK_5211) /* - * RTS failure register + * RTS failure (MIB counter) */ #define AR5K_RTS_FAIL_5210 0x8094 #define AR5K_RTS_FAIL_5211 0x808c @@ -1532,7 +1539,7 @@ AR5K_RTS_FAIL_5210 : AR5K_RTS_FAIL_5211) /* - * ACK failure register + * ACK failure (MIB counter) */ #define AR5K_ACK_FAIL_5210 0x8098 #define AR5K_ACK_FAIL_5211 0x8090 @@ -1540,7 +1547,7 @@ AR5K_ACK_FAIL_5210 : AR5K_ACK_FAIL_5211) /* - * FCS failure register + * FCS failure (MIB counter) */ #define AR5K_FCS_FAIL_5210 0x809c #define AR5K_FCS_FAIL_5211 0x8094 @@ -1667,11 +1674,17 @@ /* * Profile count registers + * + * These registers can be cleared and freezed with ATH5K_MIBC, but they do not + * generate a MIB interrupt. + * Instead of overflowing, they shift by one bit to the right. All registers + * shift together, i.e. when one reaches the max, all shift at the same time by + * one bit to the right. This way we should always get consistent values. */ #define AR5K_PROFCNT_TX 0x80ec /* Tx count */ #define AR5K_PROFCNT_RX 0x80f0 /* Rx count */ -#define AR5K_PROFCNT_RXCLR 0x80f4 /* Clear Rx count */ -#define AR5K_PROFCNT_CYCLE 0x80f8 /* Cycle count (?) */ +#define AR5K_PROFCNT_RXCLR 0x80f4 /* Busy count */ +#define AR5K_PROFCNT_CYCLE 0x80f8 /* Cycle counter */ /* * Quiet period control registers @@ -1758,7 +1771,7 @@ #define AR5K_CCK_FIL_CNT 0x8128 /* - * PHY Error Counters (?) + * PHY Error Counters (same masks as AR5K_PHY_ERR_FIL) */ #define AR5K_PHYERR_CNT1 0x812c #define AR5K_PHYERR_CNT1_MASK 0x8130 @@ -1766,6 +1779,9 @@ #define AR5K_PHYERR_CNT2 0x8134 #define AR5K_PHYERR_CNT2_MASK 0x8138 +/* if the PHY Error Counters reach this maximum, we get MIB interrupts */ +#define ATH5K_PHYERR_CNT_MAX 0x00c00000 + /* * TSF Threshold register (?) */ @@ -1974,7 +1990,7 @@ #define AR5K_PHY_SETTLING 0x9844 /* Register Address */ #define AR5K_PHY_SETTLING_AGC 0x0000007f /* AGC settling time */ #define AR5K_PHY_SETTLING_AGC_S 0 -#define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Switch settlig time */ +#define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Switch settling time */ #define AR5K_PHY_SETTLING_SWITCH_S 7 /* |
