diff options
Diffstat (limited to 'drivers/net/ethernet/dlink/de620.h')
| -rw-r--r-- | drivers/net/ethernet/dlink/de620.h | 117 |
1 files changed, 0 insertions, 117 deletions
diff --git a/drivers/net/ethernet/dlink/de620.h b/drivers/net/ethernet/dlink/de620.h deleted file mode 100644 index e8d9a88f4cb5..000000000000 --- a/drivers/net/ethernet/dlink/de620.h +++ /dev/null @@ -1,117 +0,0 @@ -/********************************************************* - * * - * Definition of D-Link DE-620 Ethernet Pocket adapter * - * * - *********************************************************/ - -/* DE-620's CMD port Command */ -#define CS0 0x08 /* 1->0 command strobe */ -#define ICEN 0x04 /* 0=enable DL3520 host interface */ -#define DS0 0x02 /* 1->0 data strobe 0 */ -#define DS1 0x01 /* 1->0 data strobe 1 */ - -#define WDIR 0x20 /* general 0=read 1=write */ -#define RDIR 0x00 /* (not 100% confirm ) */ -#define PS2WDIR 0x00 /* ps/2 mode 1=read, 0=write */ -#define PS2RDIR 0x20 - -#define IRQEN 0x10 /* 1 = enable printer IRQ line */ -#define SELECTIN 0x08 /* 1 = select printer */ -#define INITP 0x04 /* 0 = initial printer */ -#define AUTOFEED 0x02 /* 1 = printer auto form feed */ -#define STROBE 0x01 /* 0->1 data strobe */ - -#define RESET 0x08 -#define NIS0 0x20 /* 0 = BNC, 1 = UTP */ -#define NCTL0 0x10 - -/* DE-620 DIC Command */ -#define W_DUMMY 0x00 /* DIC reserved command */ -#define W_CR 0x20 /* DIC write command register */ -#define W_NPR 0x40 /* DIC write Next Page Register */ -#define W_TBR 0x60 /* DIC write Tx Byte Count 1 reg */ -#define W_RSA 0x80 /* DIC write Remote Start Addr 1 */ - -/* DE-620's STAT port bits 7-4 */ -#define EMPTY 0x80 /* 1 = receive buffer empty */ -#define INTLEVEL 0x40 /* 1 = interrupt level is high */ -#define TXBF1 0x20 /* 1 = transmit buffer 1 is in use */ -#define TXBF0 0x10 /* 1 = transmit buffer 0 is in use */ -#define READY 0x08 /* 1 = h/w ready to accept cmd/data */ - -/* IDC 1 Command */ -#define W_RSA1 0xa0 /* write remote start address 1 */ -#define W_RSA0 0xa1 /* write remote start address 0 */ -#define W_NPRF 0xa2 /* write next page register NPR15-NPR8 */ -#define W_DFR 0xa3 /* write delay factor register */ -#define W_CPR 0xa4 /* write current page register */ -#define W_SPR 0xa5 /* write start page register */ -#define W_EPR 0xa6 /* write end page register */ -#define W_SCR 0xa7 /* write system configuration register */ -#define W_TCR 0xa8 /* write Transceiver Configuration reg */ -#define W_EIP 0xa9 /* write EEPM Interface port */ -#define W_PAR0 0xaa /* write physical address register 0 */ -#define W_PAR1 0xab /* write physical address register 1 */ -#define W_PAR2 0xac /* write physical address register 2 */ -#define W_PAR3 0xad /* write physical address register 3 */ -#define W_PAR4 0xae /* write physical address register 4 */ -#define W_PAR5 0xaf /* write physical address register 5 */ - -/* IDC 2 Command */ -#define R_STS 0xc0 /* read status register */ -#define R_CPR 0xc1 /* read current page register */ -#define R_BPR 0xc2 /* read boundary page register */ -#define R_TDR 0xc3 /* read time domain reflectometry reg */ - -/* STATUS Register */ -#define EEDI 0x80 /* EEPM DO pin */ -#define TXSUC 0x40 /* tx success */ -#define T16 0x20 /* tx fail 16 times */ -#define TS1 0x40 /* 0=Tx success, 1=T16 */ -#define TS0 0x20 /* 0=Tx success, 1=T16 */ -#define RXGOOD 0x10 /* rx a good packet */ -#define RXCRC 0x08 /* rx a CRC error packet */ -#define RXSHORT 0x04 /* rx a short packet */ -#define COLS 0x02 /* coaxial collision status */ -#define LNKS 0x01 /* UTP link status */ - -/* Command Register */ -#define CLEAR 0x10 /* reset part of hardware */ -#define NOPER 0x08 /* No Operation */ -#define RNOP 0x08 -#define RRA 0x06 /* After RR then auto-advance NPR & BPR(=NPR-1) */ -#define RRN 0x04 /* Normal Remote Read mode */ -#define RW1 0x02 /* Remote Write tx buffer 1 ( page 6 - 11 ) */ -#define RW0 0x00 /* Remote Write tx buffer 0 ( page 0 - 5 ) */ -#define TXEN 0x01 /* 0->1 tx enable */ - -/* System Configuration Register */ -#define TESTON 0x80 /* test host data transfer reliability */ -#define SLEEP 0x40 /* sleep mode */ -#if 0 -#define FASTMODE 0x04 /* fast mode for intel 82360SL fast mode */ -#define BYTEMODE 0x02 /* byte mode */ -#else -#define FASTMODE 0x20 /* fast mode for intel 82360SL fast mode */ -#define BYTEMODE 0x10 /* byte mode */ -#endif -#define NIBBLEMODE 0x00 /* nibble mode */ -#define IRQINV 0x08 /* turn off IRQ line inverter */ -#define IRQNML 0x00 /* turn on IRQ line inverter */ -#define INTON 0x04 -#define AUTOFFSET 0x02 /* auto shift address to TPR+12 */ -#define AUTOTX 0x01 /* auto tx when leave RW mode */ - -/* Transceiver Configuration Register */ -#define JABBER 0x80 /* generate jabber condition */ -#define TXSUCINT 0x40 /* enable tx success interrupt */ -#define T16INT 0x20 /* enable T16 interrupt */ -#define RXERRPKT 0x10 /* accept CRC error or short packet */ -#define EXTERNALB2 0x0C /* external loopback 2 */ -#define EXTERNALB1 0x08 /* external loopback 1 */ -#define INTERNALB 0x04 /* internal loopback */ -#define NMLOPERATE 0x00 /* normal operation */ -#define RXPBM 0x03 /* rx physical, broadcast, multicast */ -#define RXPB 0x02 /* rx physical, broadcast */ -#define RXALL 0x01 /* rx all packet */ -#define RXOFF 0x00 /* rx disable */ |
