diff options
Diffstat (limited to 'drivers/net/e1000e/lib.c')
| -rw-r--r-- | drivers/net/e1000e/lib.c | 50 |
1 files changed, 13 insertions, 37 deletions
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c index 16f35fadb74b..95f75a43c9f9 100644 --- a/drivers/net/e1000e/lib.c +++ b/drivers/net/e1000e/lib.c @@ -589,9 +589,6 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw) s32 ret_val; u16 nvm_data; - if (mac->fc != e1000_fc_default) - return 0; - /* Read and store word 0x0F of the EEPROM. This word contains bits * that determine the hardware's default PAUSE (flow control) mode, * a bit that determines whether the HW defaults to enabling or @@ -1107,34 +1104,13 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { mac->fc = e1000_fc_rx_pause; hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n"); - } - /* Per the IEEE spec, at this point flow control should be - * disabled. However, we want to consider that we could - * be connected to a legacy switch that doesn't advertise - * desired flow control, but can be forced on the link - * partner. So if we advertised no flow control, that is - * what we will resolve to. If we advertised some kind of - * receive capability (Rx Pause Only or Full Flow Control) - * and the link partner advertised none, we will configure - * ourselves to enable Rx Flow Control only. We can do - * this safely for two reasons: If the link partner really - * didn't want flow control enabled, and we enable Rx, no - * harm done since we won't be receiving any PAUSE frames - * anyway. If the intent on the link partner was to have - * flow control enabled, then by us enabling RX only, we - * can at least receive pause frames and process them. - * This is a good idea because in most cases, since we are - * predominantly a server NIC, more times than not we will - * be asked to delay transmission of packets than asking - * our link partner to pause transmission of frames. - */ - else if ((mac->original_fc == e1000_fc_none) || - (mac->original_fc == e1000_fc_tx_pause)) { + } else { + /* + * Per the IEEE spec, at this point flow control + * should be disabled. + */ mac->fc = e1000_fc_none; hw_dbg(hw, "Flow Control = NONE.\r\n"); - } else { - mac->fc = e1000_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n"); } /* Now we need to do one last check... If we auto- @@ -1164,7 +1140,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) } /** - * e1000e_get_speed_and_duplex_copper - Retreive current speed/duplex + * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex * @hw: pointer to the HW structure * @speed: stores the current speed * @duplex: stores the current duplex @@ -1200,7 +1176,7 @@ s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *dup } /** - * e1000e_get_speed_and_duplex_fiber_serdes - Retreive current speed/duplex + * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex * @hw: pointer to the HW structure * @speed: stores the current speed * @duplex: stores the current duplex @@ -1410,7 +1386,7 @@ s32 e1000e_cleanup_led_generic(struct e1000_hw *hw) * e1000e_blink_led - Blink LED * @hw: pointer to the HW structure * - * Blink the led's which are set to be on. + * Blink the LEDs which are set to be on. **/ s32 e1000e_blink_led(struct e1000_hw *hw) { @@ -1515,7 +1491,7 @@ void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop) * @hw: pointer to the HW structure * * Returns 0 if successful, else returns -10 - * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not casued + * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused * the master requests to be disabled. * * Disables PCI-Express master access and verifies there are no pending @@ -1876,7 +1852,7 @@ static s32 e1000_ready_nvm_eeprom(struct e1000_hw *hw) } /** - * e1000e_read_nvm_spi - Read EEPROM's using SPI + * e1000e_read_nvm_spi - Reads EEPROM using SPI * @hw: pointer to the HW structure * @offset: offset of word in the EEPROM to read * @words: number of words to read @@ -1980,7 +1956,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) * Writes data to EEPROM at offset using SPI interface. * * If e1000e_update_nvm_checksum is not called after this function , the - * EEPROM will most likley contain an invalid checksum. + * EEPROM will most likely contain an invalid checksum. **/ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { @@ -2222,7 +2198,7 @@ static u8 e1000_calculate_checksum(u8 *buffer, u32 length) * * Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND * - * This function checks whether the HOST IF is enabled for command operaton + * This function checks whether the HOST IF is enabled for command operation * and also checks whether the previous command is completed. It busy waits * in case of previous command is not completed. **/ @@ -2254,7 +2230,7 @@ static s32 e1000_mng_enable_host_if(struct e1000_hw *hw) } /** - * e1000e_check_mng_mode - check managament mode + * e1000e_check_mng_mode - check management mode * @hw: pointer to the HW structure * * Reads the firmware semaphore register and returns true (>0) if |
