1 files changed, 49 insertions, 27 deletions

diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index 52d698bb2595..813d5e0e458d 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -428,14 +428,6 @@ e1000_up(struct e1000_adapter *adapter)
 
 	/* hardware has been reset, we need to reload some things */
 
-	/* Reset the PHY if it was previously powered down */
-	if (adapter->hw.media_type == e1000_media_type_copper) {
-		uint16_t mii_reg;
-		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
-		if (mii_reg & MII_CR_POWER_DOWN)
-			e1000_phy_hw_reset(&adapter->hw);
-	}
-
 	e1000_set_multi(netdev);
 
 	e1000_restore_vlan(adapter);
@@ -464,12 +456,56 @@ e1000_up(struct e1000_adapter *adapter)
 	return 0;
 }
 
+/**
+ * e1000_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000_reset ***
+ *
+ **/
+
+static void e1000_power_up_phy(struct e1000_adapter *adapter)
+{
+	uint16_t mii_reg = 0;
+
+	/* Just clear the power down bit to wake the phy back up */
+	if (adapter->hw.media_type == e1000_media_type_copper) {
+		/* according to the manual, the phy will retain its
+		 * settings across a power-down/up cycle */
+		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+		mii_reg &= ~MII_CR_POWER_DOWN;
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
+	}
+}
+
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+	boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
+	                              e1000_check_mng_mode(&adapter->hw);
+	/* Power down the PHY so no link is implied when interface is down
+	 * The PHY cannot be powered down if any of the following is TRUE
+	 * (a) WoL is enabled
+	 * (b) AMT is active
+	 * (c) SoL/IDER session is active */
+	if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
+	    adapter->hw.media_type == e1000_media_type_copper &&
+	    !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
+	    !mng_mode_enabled &&
+	    !e1000_check_phy_reset_block(&adapter->hw)) {
+		uint16_t mii_reg = 0;
+		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+		mii_reg |= MII_CR_POWER_DOWN;
+		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
+		mdelay(1);
+	}
+}
+
 void
 e1000_down(struct e1000_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
-	boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
-	                              e1000_check_mng_mode(&adapter->hw);
 
 	e1000_irq_disable(adapter);
 
@@ -489,23 +525,6 @@ e1000_down(struct e1000_adapter *adapter)
 	e1000_reset(adapter);
 	e1000_clean_all_tx_rings(adapter);
 	e1000_clean_all_rx_rings(adapter);
-
-	/* Power down the PHY so no link is implied when interface is down *
-	 * The PHY cannot be powered down if any of the following is TRUE *
-	 * (a) WoL is enabled
-	 * (b) AMT is active
-	 * (c) SoL/IDER session is active */
-	if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
-	   adapter->hw.media_type == e1000_media_type_copper &&
-	   !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
-	   !mng_mode_enabled &&
-	   !e1000_check_phy_reset_block(&adapter->hw)) {
-		uint16_t mii_reg;
-		e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
-		mii_reg |= MII_CR_POWER_DOWN;
-		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
-		mdelay(1);
-	}
 }
 
 void
@@ -1117,6 +1136,8 @@ e1000_open(struct net_device *netdev)
 	if (err)
 		goto err_up;
 
+	e1000_power_up_phy(adapter);
+
 	if ((err = e1000_up(adapter)))
 		goto err_up;
 	adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
@@ -1162,6 +1183,7 @@ e1000_close(struct net_device *netdev)
 
 	WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
 	e1000_down(adapter);
+	e1000_power_down_phy(adapter);
 	e1000_free_irq(adapter);
 
 	e1000_free_all_tx_resources(adapter);